JWA MIRAMAR 69406 User manual

Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
1
69406
4 Drawer Shoe Cabinet
MIRAMAR
ITEM CODE
960MM
900MM
180MM

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when ling. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instrucons carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over ghten the screws and bolts as this may damage the threads
Allow 30 min For 1 person Addional tools required
2

PARTS LIST
3
1
2
3
4
5
5
5
5
6
7
8
9
X4

PARTS LIST
4
NO. ITEM QTY
A19PCS
B19PCS
NO. ITEM QTY
G2PCS
H8PCSC
D
E
F
13PCS
4PCS
24PCS
16PCS
8PCS
8PCS
8PCS
I
J
K
NO. ITEM QTY NO. ITEM QTY
1TOP PANEL 1 PC
21 PC
Φ15*10
Φ6*35
Φ6*30
Φ4*12
Φ3*25
3
4
5
6
7
8
9
1 PC
1 PC
4 PCE
1 PC
4 PCE
4 PCE
4 PCE
LEFT SIDE PANEL
RIGHT SIDE PANEL DRAWER BACK PANEL
UPPER PANEL
BACK SUPPORT PANEL
FRONT SUPPORT PANEL
DRAWER DOOR PANEL
DRAWER BOTTOM PANEL

STEP 1:
STEP 2:
5
E X24D X4
X4
X4
F X8
F
F
7
9
D
D
EEE
E
EE
7

STEP 3:
STEP 4:
6
X4
F X8
7
89
F
F
4
4
A
A
A
AHH
H
H
K
K
K
K
K X4H X4A X4

STEP 5:
STEP 6:
7
K X4H X4A X8
3
2
KK
K
K
HH
H
H
A
A
A
A
AA
A A
A X1
A
6

STEP 7:
STEP 8:
8
6
B
B X1
4
B X6C X5
B
B
B
BB
B
C
C
C
C
C
3
4
6
5
5

STEP 9:
STEP 10:
9
B X6C X5
C
C
C
C
C
B
B
B
B
BB
4
2
6
5
5
3
G X2A X6
1
A
AA
A
A
A
G
GG
G

STEP 11:
STEP 12:
10
B X6C X3
J X8I X8
1
C
C
C
B
B
B
B
23
4
6
I
I
J
J
J
JI
I

STEP 13:
11
G X2
WALL
G
G
G
G

ASSEMBLY IS COMPLETE
12

13
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
WALL
BACK SLDE
SCREWS X1 SCREWS X1WALL FIXING X1 Expanded plastic pipe X1
HARDWARE

To protect your furniture, we suggest the following:
• Avoid placing your furniture in direct sunlight.
• Do not place furniture directly under windows.
• Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
• Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
• Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void
14