JWA JARVIS 74673 User manual

Imported by JWA Furniture Pty Ltd, Brisbane Qld, Australia.
For any assistance with assembly or for missing parts please refer to your receipt
1
ASSEMBLY INSTRUCTION
ITEM CODE 74673
JARVIS Lingerie Chest

Allow 6 0min For2person Additional toolsrequired
PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when liing. Product should be assembled as near as possible to the
point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instrucons carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over ghten the screws and bolts as this may damage the threads
7. Assembly is to be carried out by a competent adult(s) ONLY
8. During assembly, children should be kept away from the product due to possible
risk to injury.
9. Do not use this item if any components are missing or damaged.
10. Please keep the instrucons for future reference.
2

8mm
3

PARTSLIST
A
22pcs
M6x40mm
BCEF
J
O
22pcs
15x12mm
20pcs
8x30mm
1pc
M4 4pcs 4pcs
48pcs
32pcs
P
Z1 Z2
ST
6pcs
16pcs
1pc
1pc
GHI1 N
32pcs 1pc
V1
M3.5x12
16pcs 16pcs
12x10.5mm
4
M6x34mm
M6x15mm
I2=2pcs
V2=12pcs

5

STEP 1: Fixdowel(B) and campin (A)to panel(2) (3) (4) (5).
6

7
STEP 2: Fix rails (N-1) to panel (3) (4) with screw (V1) .
N-1=8
V1=24
Front
Back
hole location
N-1 N-2

8
STEP 3: Fix panel (6)to panel(5)withcamlock (C).
STEP 4:
Fix panel (8) to panel (5) with cam lock (C) .
Fix panel (5) (6) (8) (14) (15) to panel (3) (4) with cam
lock (C)

9
STEP 5:
Insert panel (7) into grooves between panel (2) (3) (4).

10
STEP 6:Fix panel (2) to panel (3) (4) with cam lock (C) .

11
STEP 7:Fix metal leg (J) to bottom panel (2) with bolt (G) ,
lock washer (Z1), washer (Z2). Using allen key ( ) to fix
100% as shown.
H

12
STEP 8:Attach pneumatic rod (S-1) to panel (3) with screw.
Insert soft closing bumper (T) into hole panel (4).

13
STEP 9:Attach hinge (I1) to panel (1) with screw (V2).
STEP 10:Fix top panel (1) to panel (6) with screw (V2).
V2
V2
V2 V2
V2

14
STEP 11:Adjust to proper position.

15
STEP 12: Attach pneumatic rod (S-2) to panel (1) with screw.

16
1
STEP 13-1:Fix cam pin (O) to panel (9) (10) (11) (12).
STEP 13-2:
Fix panel (10) to panel (11) (12) with cam lock (P).
Insert panel (13) into grooves between panel (10) (11) (12).
Fix panel (11) (12) to panel (9) with cam lock (P).
STEP 13-3:Fix rails (N-2) to panel (11) (12) with screw (V1)

17
STEP 14:Adjust to proper position.

STEP 15:Insert the back panel hook (E) into the back and using
screw to fix , as shown.
18

19
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
all Back side
Mounting Plate x 2 all Strap x 1 Large Screw x 2 Small Screw x 2
HARDARE

20
ASSEMBLY COMPLETE