JWA 70823 User manual

ASSEMBLY INSTRUCTION
Advance
2drw Clothes Rack
ITEM CODE 70823
1

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that
may damage the product
2.Take care when lifting. Product should be assembled as near as possible
to the point of use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instructions carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over tighten the screws and bolts as this may damage the threads
Allow 45min For 2 person Additional tools required
Serious or fatal injuries may occur from furniture toppling over.
To help avoid this please follow the below recommendations;
· Install the provided"Tipping Kit" as per the instructions
· Never allow children to climb on or hang off of any part of this
product
· Unless specifically designed to accommodate,do not set Tvs or
other heavy objects on top of this product
IFthisproducthasdrawers:
· Place the heaviest items in lowest drawers
· Do not open more than 1 drawer at a time as this may cause
the product to become unbalanced
· Do not tamper with or remove any drawer
interlocking/running system
Note:The use of the provided"Tipping Kit" may reduce but not
necessarily eliminate the risk of furniture toppling over.
Please use this product with caution.
This is a permanent label.Do not attempt to remove!
TIPPING WARNING
2

PARTS LIST
ABCDE
FG
3
H
1top panel
middle layer
2
back panel
3
P1
5
ST3.5X14mm
20pcs
ST3.5X18mm
6pcs
ST5X50mm
12pcs 8pcs 6pcs
24pcs
M6X40 mm
8pcs
M6X30 mm
16pcs
M4X18mm
4pcs
E1
E2
4pcs
2pcs
ST4X25mm
2pcs 2pcs 2pcs 4pcs
KLM
I J
N O
1
3
2
3
4
6
7
8
10
11
12
14
9
P1
P2
P2 P3
P3
13
4
5
6
7
8
9
10
11
12
13
14
P1
P2
drawer top panel
dr a we r b ot t o m p a n el
Left side panel
right side panel
back panel
drawer front panel
drawer left panel
drawer right panel
drawer back panel
drawer support panel
drawer bottom panel
metal frame
back net
P3 coat hanger

STEP 1:
STEP 2:
Sc r ew t he f it t in g O in t o t h e P1 .
At t ac h th e P3 t o t he P 1 wi t h f i tt in g C .
4
O
O
O
O
P1
P1
C
C
C
C
P1
P1
P3 P3

STEP 3:
STEP 4:
At t a c h P2 t o th e P 1 wi th f i t t in g B.
At t a c h th e pa n el 3 t o Pa n e l 1 w it h fi t t i ng H . Th e s am e pr oc e ss f or t h e P a ne l
2.
5
B
B
BBB
B
B
B
P2 P2
3
1
3
2
H
H
H
H
P1
P1

STEP 5:
STEP 6:
6
Rai se the plas tic tab o n th e runne rs and sepa rate E1 f ro m E2.
At t ac h th e co m po ne n t s o f st ep 4 t o P 1 w i th f it t in g C.
2
1
C
CC
C
E1 E2
E1 E2
P1
P1

STEP 7:
STEP 8:
7
Attach the Pa n e l 6 a nd 7 t o th e P an el 5 w i t h f it ti n g A a n d I.
Us e f it ti ng F t o f ix E 1 at t h e c o rr es p o n di ng p o si ti o n s h ol es o f P a n el 6
an d P an el 7 .
67
E1
E1
E1
E1
F
F
F
FF
F
F
F
6
7
5
A
A
A
A
I
I
A

STEP 9:
STEP 10:
8
Attach Panel 4 to p a n e l 6 an d 7 wi t h fi tt i n g A a nd I .
In s er t th e Pa n el 8 t o pa n e l 6 ,7 a nd 5 a l i g n the groove.
8
4
6
7
A
A
AA
I
I
A
6
7
5

STEP 11:
STEP 12:
9
As the direction o f arrow, insert the component o f P an el 5 i n t o t he
bottom of metal f ra m e, a nd f a s t en w it h f it ti ng C.
In s er t th e fi t ti ng J t o t h e c or re s p o nd in g h ol es o f Pa n el 8 a nd f a s t en w it h
fitting G.
J
G
8
5
C
C
C
C
P1
P1

STEP 13:
STEP 14:
10
At t a c h th e ha n dl e K to t h e P a ne l 9 wi t h f i tt in g D . An d in se r t Pa ne l 1 4 i n to
Pa n e l 1 0 ,1 1 an d 1 2 al ig n t h e g ro ov e . T h en a tt a ch p an el 9 t o t he c om p o n en t
with fitting A.
At t ac h th e Pa n el 1 0 an d 1 1 t o P an el 1 2 w i t h fi tt i ng H , th e n a t ta ch P a n e l 13 t o
Pa n el 1 2 wi th f i tt in g A .
11
12
13
H
H
H
H
A
A
10
A
A
A
14
9
11
A
9
10
13
D
K
A