JWA SALTA 73033 User manual

1
Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
SALTA
ITEM CODE 73033/73035
QUEEN BED
Allow 20 minutes Addional tools requiredFor 2 person
PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the product
2. Take care when liing. Product should be assembled as near as possible to the point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instrucons carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over ghten the screws and bolts as this may damage the threads.

2
PARTS LIST
A
Bolt
M8 x 30mm 12 x A
B
Allen Key
M8 1 x F
C
Washer
M8 2 x C
F
Bolt
M6 x 40mm 8 x B
E
Bolt
M8 x 20mm 8 x E
2 FOOTBOARD ( x 1 )
1 HEADBOARD ( x 1 )
4
CENTER RAIL ( x 2 )
3 SIDE RAIL RIGHT ( x 2 )
6
FLAT SLAT 1540mm x 62mm x 14mm
7
CENTER SUPPORT LEG ( x 1 )
5
PLASTIC LEGS ( x 4 )
DG
Bolt
M8 x 50mm 4 x G
H
Bolt
M6 x 30mm 8 x H
Nylon Nut
M8 2 x D
9
METAL LEGS ( x 2 )
1.
2.
3.
4.
3.
10.
5.
6.
6.
6.
6.
7.
10.
5.
4.
9.
8.
9.
8
Center Support Legs
175mm 1 x 8.
5
Center Rail
1033mm 2 x 5.
9
Support Legs
175mm 2 x 9.
10
Metal Legs
150mm 2 x 10.
Allen Key
M6 1 x I
I
CARTON
CARTON
Step 1: Unpack the Carton Top. Step 2: Remove the plasc and carton edge fold down.
Step 3: Unzip the Woven Cover. Step 4: Open the Woven Cover.
8
SUPPORT LEG ( x 2 )
10
SIDE RAIL LEFT ( x 2 )

Step 5: Remove the Foam. Step 6: Rip the Velcro.
Step 7: Remove the Foam. Step 8: Slowly take out the Side Rail.
Step 9: Take out the Plasc Legs.
Step 11: Take out the Center Support Legs. Step 12: Slowly take out another Side Rail
3
Step 10: Take out the Metal Legs + Hardware.

Step 13: Slowly move the Slat to the end.
Carefully li up one side.
Step 14: Then take out the whole Slat.
Step 15: Slowly move the Footboard to the end.
Carefully li up one side.
Step 16: Then take out the whole Footboard.
Step 17: Sck the Velcro. Step 18: Close back the Woven Cover.
Step 19: Then Zip it back to normal.
4
Step 20: Flip the Headboard.

Please ensure the legs are fix and same position according to diagram 1.
Step 21 : Attach the Legs (6.) to the bottom of Headboard (1.) and Footboard (2.) by screwing in
a clockwise direction. Then tighten them before you continue to the next step.
Note :
Diagram 1
1 & 2. 6.
1.
2.
6.
6.
B.
B.
B.
B.
6.
6.
Note : Please ensure the legs are fix and same position according to diagram 1.
B. M6 X 40mm ~ 8nos
Step 22: Attach the 2 Side Rail (3.) & (4.) with Metal Legs (10.) using the screw E. M8 x 20mm by
screwing in a clockwise direction. Then tighten them.
Step 23 : Attach Side Rail (3.) & (4.)to Headboard (1.) and Footboard (2.) by hooking the bracket on
Side Rail (3.) & (4.) to pre installed bolts on Headboard (1.) and Footboard (2.). Do not tighten until
center rail attaches.
E. M8 X 20mm ~ 8nos
3.
4.
3.
4.
10.
4
3
10
E.
A. M8 x 30mm ~ 8nos.
A.
1.
2.
5
Slighly losen
the prex screw
for hook in bracket
A.
1& 2
1& 2
3 & 4
3 & 4

6
Adjustable
Step 24 : Attach the 2 Center Rail (5.) with Center Support Rail (8.) using screw G. M8 x 50mm with
D. M8 Bolt and C . M8 Washer on Center Rail (5.).Install the Support Leg (9) using screw
G. M8 X 50mm on Center Rail (5.).
G. M8 X 50mm ~ 4nos
D. M8 ~ 2nos
C. M8 ~ 2nos
9.
9.
5
9
9
G.
5.
5.
8.
5
5
8
D.
C.
G.
Step 26 : Attach Flat Slat and fix with screw (H).
Step 25 : Attach Center Rail (5.) to Headboard (1.) and Footboard (2.) by screwing in a clockwise
direction and tighten them.
A. M8 X 30mm ~ 4nos
H. M6 X 30mm ~ 8nos
1.
2.
5.
5
1 & 2
A.
7
3 & 4
H.

7
Note : Please Lift up the bed to move, DO NOT push or pull the bed with mattress on top.
ASSEMBLY IS COMPLETED
•
•
•
•
•
•
Product Name : SALTA QUEEN BED
Item Code : 73033 / 73035
PRODUCT CARE
To protect your furniture, we suggest the following:
Avoid placing your furniture in direct sunlight.
Do not place furniture directly under windows.
Do not place sharp materials (knife, fork, etc.) directly onto your furniture as sharp
material may scrape and damage the finish.
Do not place material with high temperature directly onto the surface of your furniture.
Clean up spills quickly. Water left over a prolonged period of time may cause damage.
Alcohol, perfume, nail polishes, aftershave and some medication may cause severe finish
damage if not cleaned immediately.
Use a clean, soft, dry, lint free absorbent cloth to clean your furniture. Do not use any
detergent as they may contain ingredients that may react and damage the finish.
Made In: Malaysia
Imported By:
JWA Furniture Pty Ltd
Brisbane, Old, Australia
Item Code: 73033 / 73035
Product Name: SALTA QUEEN BED