JWA LACHEN 70445 User manual

ASSEMBLY INSTRUCTION
LACHEN
GAMING TABLE
ITEM CODE 70445
1200mm
600mm
760mm
1

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that
may damage the product
2.Take care when lifting. Product should be assembled as near as possible
to the point of use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instructions carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over tighten the screws and bolts as this may damage the threads
Allow 45min For 2 person Additional tools required
Serious or fatal injuries may occur from furniture toppling over.
To help avoid this please follow the below recommendations;
· Install the provided"Tipping Kit" as per the instructions
· Never allow children to climb on or hang off of any part of this
product
· Unless specifically designed to accommodate,do not set Tvs or
other heavy objects on top of this product
IF this product has drawers:
· Place the heaviest items in lowest drawers
· Do not open more than 1 drawer at a time as this may cause
the product to become unbalanced
· Do not tamper with or remove any drawer
interlocking/running system
Note:The use of the provided"Tipping Kit" may reduce but not
necessarily eliminate the risk of furniture toppling over.
Please use this product with caution.
This is a permanent label.Do not attempt to remove!
TIPPING WARNING
2

PARTS LIST
ABC D E
FGH
M6X50 mm
4pcs
M6X30 mm
8pcs
M6X12mm
6pcs
ST3.5X14mm
4pcs 2pcs
1pc 2pcs 4pcs
1Desktop panel
1
P1
P2
P3
P4
Left Frame
P1
Right Frame
P2
Connection Pipe
P3
Support Pipe
P4
P5
Rack
P5
ST4X25mm
2pcs 2pcs
2pcs
IJ
K
3

STEP 1:
H
H
H
H
A
A
A
A
C
C
C
C
STEP 2:
P1 P2
P3
P4
P1
P2
Insert the fitting H into the P1 and P2.
1.Assemble the P3 to P1 and P2 with fitting C.
2.Then assemble the P4 with P1 and P2 with fitting A.
4

STEP 3:
STEP 4:
BBBB
BBBB
1
G
D
C
Assemble the Panel 1 onto the metal frame with fitting B.
P4
Install the rack G at righ t side of the desktop with
fitting C and D.
5

STEP 5:
STEP 6:
F
E
E
Put the fitting E and F accordingly as the below picture.
1. Install the belt K onto the desktop with fitting D.
2. Insert the fitting J into the wall, and connect it
with the belt by fitting I.
1
KJ
I
D
K
1
6

STEP 7:
Assembly complete!
7

8
To protect your furniture, we suggest the following:
• Avoid placing your furniture in direct sunlight.
• Do not place furniture directly under windows.
• Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
• Do not place material with high temperature directly onto the
surface of your furniture.
• Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
• Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void