JWA HARDING 74705 User manual

Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
1
74705
4 DRAWER TALL CHEST
HARDING
ITEM CODE
800MM
400MM
940MM

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when lig. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instrucns carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over hten the screws and bolts as this may damage the threads
Allow 1 hour For 2 person Addinal tools required
2

PARTS LIST
3
1
2
3
4
56
6
6
7
8
X4
9
10
11
12
13
13
14
14
15 15
16 16

4
NO. ITEM QTY NO. ITEM QTY
A34PCS
B34PCS
C14PCS
D4PCS
E
16PCS
F16PCS
O
I
J4PCS
K4PCS
L
P
4PCS
Φ6*35
Φ15*10
Φ6*30
Φ4*40
Φ3*16
PARTS LIST
Φ3*12
G
1PC
H48PCS
4PCS
M8PCS
N16PCS
Φ3.5*12
1PC
8PCS
Φ6*30
QΦ5*30 8PCS
R8PCS
S20PCS
Φ4*35

9
5
NO. ITEM QTY NO. ITEM QTY
PARTS LIST
NO. ITEM QTY NO. ITEM QTY
1TOP PANEL 1 PC
3
1 PC
1 PC
41 PC
51 PC
4 PCE
4 PCE
4 PCE
4 PCE
4 PCE
2LEFT SIDE PANEL
13
RIGHT SIDE PANEL
BOTTOM PANEL
6
7
8
10
11
12
BOTTOM SUPPORT PANEL
3 PCE
4 PCE
2 PCE
BACK SUPPORT PANE
DRAWER FRONT PANEL
DRAWER LEFT SIDE PANEL
DRAWER RIGHT SIDE PANEL
DRAWER BACK PANEL
DRAWER BOTTOM PANEL
DRAWER SUPPORT PANEL
BACK PANEL
14
15
16
2 PCE
2 PCE
2 PCE
METAL LEG
METAL LEG
METAL LEG

STEP 1:
STEP 2:
6
A X6
1
A
A X2
A
AA
A
A
4
AA

STEP 3:
STEP 4:
7
A X6
2
A
C X6
J X4I X4H X24
3
A
A
A
A
A
I
I
I
I
J
J
J
J
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
B X6
2
3
6
6
6
B
B
B
B
B
B
C
C
C
C

STEP 5:
STEP 6:
8
B X2
1
B
C X4
5
B
B X4
1
2
3
5
6
6
6
B
B
B
B
C
C

STEP 7:
STEP 8:
9
2
3
13
13
C X4B X2 D X4
2
3
4
B
D
D
D
D
C
C

STEP 9:
STEP 10:
10
Q X8
15
O
3
O X1
P X8O X1
R X8
P
P
P
P
P
P
P
P15
16
16
14
14
4
15
15
16
16
O
Q
Q
Q
Q
Q
Q
Q
Q
R
R
R
R
R
R
R

STEP 11:
STEP 12:
11
X4
10
A7
7
8
8
8
9
9
9
10
10
11
11
12
AA
A
BB
B
S
S
S
M
M
N
N
A X20B X20S X20M X8N X16
7
K
L
H
H
H
H
H
9
H
H X24L X4K X4
X4

STEP 13:
STEP 14:
12
F X16G X16
2
13
G
GG
G
G
G
G
E
G
G
G
G
E
G
G
F
F
F
F
F
F
F
FF
FF
FF
F
F
F
F
F
13
G
7
7
7
7

STEP 15:
13
E X1
E
E
E
WALL E
EE
ASSEMBLY IS COMPLETE

14
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
WALL
BACK SLDE
SCREWS X1 SCREWS X1Anti-tiit Strap X1 Expanded plastic pipe X1
HARDWARE
washer X2

To protect your furniture, we suggest the following:
• Avoid placing your furniture in direct sunlight.
• Do not place furniture directly under windows.
• Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
• Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
• Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void
15