JWA MAXIMILIAN 70412 User manual

1
Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
70412/70413
QUEEN 4 POST BED
MAXIMILIAN

PRE-ASSEMBLY PREPARATION
2
Before you start:
1.Choose aclean, level, spacious assembly area.Avoid hard surfaces that may damage the
product
2.Take care when lifting.Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instructions carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over tighten the screws and bolts as this may damage the threads
7.Assembly is to be carried out by acompetent adult(s) ONLY
8.During assembly, children should be kept away from the product due to possible risk to
injury.
9.Do not use this item if any components are missing or damaged.
10.Please keep the instructions for future reference.
Allow 30 min For 2person Additional tools
required

3
PARTS LIST
1Headboard x 1pc 8End Cap x 26pcs
2Cross Rail x 2pcs 9Centre Cap x 13pcs
3Siderails x 2pcs 10 Head Post L/R x 2pcs
4Cross Bar x 2pcs 11 Foot Post L/R x 2pcs
5Centre Rail x 1pc 12 Canopy Short Rail x 2pcs
6Support Leg x 3pcs 13 Canopy Long Rail x 2pcs
7Slat (752mm) x 26pcs

4
STEP 1:
•Prepare a protected surface with a blanket or cardboard.
•Attach the headboard(1), cross rail(2) and canopy short rail(12)
to the 2x head post(10), as shown below. Use 6x bolt(B) per post.
Fasten with Allen key(F).
•Attach the cross rail(2) and canopy short rail(12) to the 2x foot
post(11), as shown below. Use 4x screw(B) per post. Fasten with
Allen key(F).

5
STEP 2:
•Connect a side rail(3) to the head post(10) and foot post(11).
Secure with 2x bolt(B) per corner. Fasten with Allen key(F).
•Repeat for the other side rail.
•Attach the 2x canopy long rail(13) to the head post(10) and foot
post(11). Use 4x bolt(B) per rail. Fasten with Allen key(F).

6
STEP 3:
•Attach the 3x supports(6) to the centre rail(5), as shown below.
Use 2x bolt(A) per leg, threaded from the top, and lock with
nut(E). Fasten with Allen key(F) and hold the nut with a pair of
pliers.
•Attach the cross rails(4) near the head post and foot post, as
shown below. Thread bolt(C) from the top on every corner, and
lock with nut(E). Fasten with Allen key(F) and hold the nut with a
pair of pliers.
•Attach the centre rail(5) to the cross rails(4), as shown below.
Thread 2x bolt(D) from the top, in the middle of each cross
rail(4), and lock with nut(E). Fasten with Allen key(F) and hold
the nut with a pair of pliers.

7
STEP 4:
•Attach an end cap(8) onto every slat, 1 per slat(7).
•Take 2x slats and cup the non capped end into either side of
the middle cap(9). Form 13x slat pairs.
•Attach the slat pairs to the bed as shown below. Push the caps
into the holes.

8
Assembly Is Complete

9
PRODUCT CARE:
FURNITURE / BED
1. When assembling your furniture / bed please ensure that you have
checked the contents for all relevant parts.
2. When tightening bolts make sure that they are fully tightened but not
forced.
3. When moving your fully assembled bed you must first remove the
mattress and lift the frame into position, take care when lifting and
always have two people handling the bed. PLEASE DO NOT DRAG THE
BED as this will cause damage to the rail.
4. It is advisable to use approved cleaning products when cleaning the
furniture and bed frame as certain chemical based cleaners could have
an adverse effect on the bed finish.