Kaboodle W-50130 User manual

Cordless drill with:
• Number 2 screw tip
• 2mm drill bit
• 5mm drill bit (for
Ø5mm peg holes)
Tape
measure
Screw
driver
Safety
gearPencil
Tools you will need
To put your kaboodle kitchen accessory together you will need the following tools.
drilling template x 2
G
slimline lift
mechanism x 2
AE
Ø4 x 38mm screws
x 6
F
Ø4 x 16mm screws
x 4
B D
door brackets
cover caps x 2
C
mechanism
cover caps x 2 door brackets x 2
Hardware included
Things you need to know
p. 1Ver. 1
W-50130 / W-50131
Follow these
instructions to
add your parts
and accessories.
• Always read the full instructions prior to installation.
• Consider possible obstructions to your part and accessories,
like hinges inside the cabinet or adjacent cabinet doors
and handles, prior to installation.
• Make sure you leave plumbing and electrical work
to qualified trades people. Never try this yourself.
• Make sure you always use safety gear like a mask, ear muffs
and glasses when using tools.
• Tip: After marking out the pre-drill holes as per the
instructions, take the part that is to be installed and align
the appropriate holes with the markings to ensure they
match up prior to pre-drilling the holes.
• If you have any questions, contact us on:
Australia: 1800 666 078 Monday to Friday between
8:00am and 6:00pm AEST, New Zealand: 0800 522 663
Monday to Friday between 8:00am and 5:00pm NZST
or email: [e-mail].
slimline cabinet door lift mechanism
step 2

step 2
p. 2Ver. 1
W-50130 / W-50131
Position mechanism so that pegs locate
into 5mm peg holes. Fix with 3 x 38mm
screws each side.
Caution when opening arm. The arm of this device could spring up and
cause injury. Do not push the arm down
without door attached.
Use included 16mm screws to fix
the door brackets to the door. Clip door bracket into place on hinge arm.
1.
3.2.
6.
7.
p. 2
attaching slimline cabinet door lift mechanism
position cabinet drilling
template
pre-drill locator holes fitting mechanism
fitting door brackets
Position included drilling template on
cabinet sides and mark out drilling
positions. 2 x peg holes (Ø5x5mm) and 3x
screw holes (each side). Refer back page for
actual drilling measurements (if required).
Pre drill 2 x peg holes (Ø5x5mm) and
screw holes.
attaching door
to mechanism
G
F
Pre drill locator holes as marked
5.
pre drill locator holes
E
A
A
Mark out drilling positions for door brackets
on each side of door as per above.
Top of door
4.
mark out drilling positions
for door brackets
An audible “click” will be
heard when locked in place.
27
76.532
F
C

step 2
p. 3Ver. 1
W-50130 / W-50131
To adjust doors horizontal position, turn cam
screw at front of hinge arm accordingly.
8.
9.
attaching slimline cabinet door lift mechanism
adjusting door tension
adjusting door position
If door is dropping, increase door
resistance by turning adjustment
screw clockwise until door holds
in position
If door is lifting, decrease door
resistance by turning adjustment
screw counter clockwise until door
holds in position
1. vertical adjustment
2. horizontal adjustment
3. depth adjustment
1
2
3
1 2 3

step 2
p. 4Ver. 1
W-50130 / W-50131
attaching slimline cabinet door lift mechanism
step 1
step 2
step 3
step 4
Then follow the
instructions to fit
your doors and
panels.
Finish off your
Kaboodle Kitchen
by installing your
benchtop.
You’ve installed
your parts and
accessories.
Your cabinets are
now assembled.
caring for your kaboodle parts and accessories
Looking after your parts and accessories is really easy and with the right care and maintenance
they will last you for many years. Just follow these simple step. Hinges, runners and other parts and
accessories should be kept dry at all times.
To keep the mechanisms performing at their best, regularly wipe them with a dry cloth removing
any dust and grime that may build up. We offer a dedicated customer service line for advice or any
questions you may have on Kaboodle products.
Just follow these simple steps and if you need any more information you can contact
us us: Australia: 1800 666 078 Monday to Friday between 8:00am and 6:00pm AEST.
New Zealand: 0800 522 663 Monday to Friday between 8:00am and 5:00pm NZST
or email: [e-mail].
Fit covers to mechanism. Covers are labelled
L and R to to easily identify position.
Peg position and space requirement Fixing position
3x wooden screws Ø4x 38mm
10.
11.
fitting covers
Installation dimensions as per drilling template