KAM TRI 160 User manual

instruction manual
www.kam.co.uk
l Setting DIP SWITCH NO.1 & NO.10 in “ON”, theTRI 160 LASER can be
control by DMX controller.
l When using a DMX controller, the mini-controller function is no
available. When using the mini-controller, the DMX function is not
available.
l Linkable laser to master & slave by DMX control, Master & slave DIP
SWITCH setting to No.1 & NO.10 in “ON”, then all lasers will show same
patterns work together in sync.
l Linkable laser to master & slave by DMX control, Master laser DIP
SWITCH setting to No.1 & NO.10 in “ON”, slave lasers DIP SWITCH
setting will follow laser function DMX channels binary number to setting
in different switch number in each unit. Then all lasers will show
different patterns by DMX controller setting program to work.
l When not using DMX controller to control laser light, the DIP SWITCH
No.10 in “ON”, then the laser light will be in sound activated mode
When not using a DMX controller to control laser light, the DIP SWITCH
No.1 in “ON”, then the laser light will be in automatic mode
l When not using a DMX controller to control laser light, for linking , the
Master DIP SWITCH No.1 in “ON”, Slave No.2 in “ON”, the laser will be is
automatic mode.
l When not using a controller to control laser light, the laser light will be
in automatic and sound active mode. The laser light can be linked in
master and slave mode . set DIP SWITCH as follows:
Master DIP SWITCH address: From NO.1 to NO.10 in “OFF”.
All slave DIP SWITCH address: NO.2 in “ON”.
l The Tri 160 laser is designed with a black out function.
When there is no sound to active The Tri 160 laser the laser will go into
black out mode. And when sensitivity is set to low the laser will go into
black out mode.
Technical Specification
Operation Voltage: AC 220V~240V/50Hz
Working power: 15W
Laser Wavelength: 532nm, 650nm
Laser power: 532nm/30mW +650nm/100mW
Laser class: Class IIIb
Fuse: 3A F
Channels: 10 channels
Control signal: DMX512 signal
Control mode: DMX/Sound active/Automatic
Net weight: 5.00Kg
Light body Dimensions: 400x230x120mm
Attention: The laser light is designed only for use indoors
Operating temperature is 10°~ 60°C.
Due to continuous product development, specifications
and appearance are subject to change. E&O E.
KAM KSM1100
KAM TRI 160 LASER
KAM TRI 160 LASER
TRI160_manual 12/10/07 11:10 Page 1

INTRODUCTION
Thank you for purchasing the KAM TRI 160
LASER”. To optimize the performance of this
product, prior to use, please read these
operating instructions carefully to familiarize
yourself with the basic operations of this unit.
The TRI 160 LASER has the KAM funky design
and is an amazing Laser effect. Please keep
these user instructions in safe place for future
reference. This unit has been Tested at the
factory before being shipped to you.
There is no Assembly required.
Warning!
To prevent or reduce the risk of electrical shock
or fire, do not expose this unit to high
Temperature / rain or moisture.
Laser Class 3B product. National
Regulations must be adhered to at all steps of
installation.
(In Germany apply DIN 56912 and BGVR LASER
note: additional Regulations may apply).
Unintended reflections of the laser beam from
reflective or metallic surfaces can be
dangerous.
This appliance is to used by Qualified personnel
only.
Laser Radiation Warning
This unit uses diode lasers in green and red. This
is CLASS 3B laser product.
Avoid exposure to eyes. Never open the laser
diode box, please refer unit to a qualified engi-
neer for servicing or repairs
OVERVIEW
DMX LASER TRI 160
Green: 532nm 30mW/ Red:650nm 100mW/
Yellow:130mW
Red and green and yellow laser
DMX 512 10 channel
40 pre programmed moving patterns
Sound activated, auto and DMX modes
Static, flat beam and pulse gobo effects
Linkable Master/Slave in sound active,
automatic, DMX
Trigger mode, built in black out with in no sound
Micro step scanning motor
Stand alone mode or DMX 512
Key switch
Endless show creation possibilities
Easy-Mini controller
XLR DMX in and out
DMX connection
DMX INPUT: DMX signal input -
Male XLR
DMX OUTPUT: DMX signal output -
Female XLR
MIC: Sound active
Min-Max: Adjust the sensitivity knob for sound
active
POWER SWITCH: ON/OFF power
FUSE: 3A Fuse
DMX channels functions and options
When using a DMX controller, DIP SWITCH 1~10
setting as follows: NO.1 & NO.10 in
“ON” for control via DMX.
PANEL
(A) DMX INPUT: DMX signal input----Male XLR
(B) DMX OUTPUT: DMX signal output----
Female XLR
(C) MINI CONTROLLER: Use 5-XLR Male
(D) DIP SWITCH: DMX address
(E) MIC: Sound active
(F) MIN-MAX: Adjust the sensitivity knob for
sound active
(G) POWER SWITCH: ON/OFF power
(H) KEY: LOCK laser
(I) MAINS INLET WITH FUSE: 3A F
A
CHANNEL DMX512 OPTIONS FUNCTION
1 0~63 Sound active programs
64~127 Automation program (3ch-10ch not available)
128~191 Manual and with sound activation
192~255 Automation and automatic activation
2 0~63 Blackout
64~127 On blanking off
128~191 Pulse
192~255 Off blanking on
3 0~255 Select patterns
4 0~255 gobo moving speed
5 0~63 Keep gobo to static
64~255 Gobo change to flat effect
6 0~63 Keep gobo to static
64~127 Follow the gobo form pulse to fast speed
dotting effect
128~191 Follow the gobo form pulse to middle speed
dotting effect
192~255 Follow the gobo form pulse to slow speed
dotting effect
7 0~63 Keep gobo to static
64~255 Gobo to up and down
8 0~255 Laser effect projection speed.
9 0~255 Control the gobo to zoom
10 0~255 Slow-draw speed, There are 12 mode speeds
to control gobo to slow-draw.
From slowly and fast.
l When using a DMX controller with the laser select No.1ch to Manual mode or Automation
mode, and select No.2ch to line.
l When using a DMX controller with the laser, please note No.4ch to 0, speed function doesn't
work. Select No.4ch speed mode function to begin working from small to large. images
BD
CE
F
GHI
TRI160_manual 12/10/07 11:10 Page 2