Kapro Prolaser 862 User manual

862 Laser level
Maintenance manual
KAPRO
1

Catalogue
1.Basic function……………………………………………………………………3
2. instrument structure………………………………………………………… 4-8
2.1、Final assembly ………………………………………………………… 4
2.2、Battery cover assembly……………………………………………… 5
2.3、Pendulum assembly ………………………………………………… 6
2.4、Lock seat assembly …………………………………………………… 7
2.5、Battery box assembly………………………………………………… 8
2.6、Electrical jobs chart……………………………………………………… 8
3.Common fault and eliminating methods………………………………………9
3.1、Don’t start up…………………………………………………………………9
3.2、fter startup without laser line …………………………………………………9
3.3、fter startup cannot level …………………………………………………9
4.SPEC………………………………………………………………………………10
2

1. Basic function
The instrument can produce two mutually orthogonal laser sector (a horizontal and a vertical
plane).Laser sector projected on the walls, laser line creating two orthogonal.
As shown in the figure below laser projection.
3

2、Instrument structure
2.1 Final assembly
NO
.
NAME Material TY
1862 摆体组 Pendulum Assembly 1
2862 1/4“base screw sus304 1
3886-23 电池盖组 battery cover
assembly
1
4862 主板 main board PCBA 1
5 GB_CROSS_SCREWS_TYPE1
M2.5X5-5 H type-N
2
6862 开关钮 Switch button PA6+30GF 1
7862 开关卡座 Switch seat POM 1
4

8873 开关 switch 1
862 窗玻璃橡胶 window rubber SI RUBBER 1
10 862 按键标贴 label PC 1
11 862 电池按钮 battery cover
button
PA6+30GF 1
12 862 窗玻璃 window K9 1
13 873 紫铜片联接钉 Copper sheet
screw
2AL12 1
14 GB_FASTENER_WASHER_SMW
C 2.5
SUS304 2
15 GB_CROSS_SCREWS_TYPE128
ST2.2X4.5 H C-N
SUS304 1
16 GB_CROSS_SCREWS_TYPE128
ST2.2X .5 H C-N
SUS304 1
17 GB_CROSS_SCREWS_TYPE128
ST2. X13 H C-N
SUS304 4
18 862 右外壳 shell right ABS 1
1 862 左外壳 left right ABS 1
20 862 锁紧座组件 locking
assembly
1
21 862 电池盒组件 battery box
assembly
1
2.2.Battery cover assembly
5

NO. NAME Material TY
1935 磁铁 Magnet MAGNET 2
2862 橡胶塞 rubber SI
RUBBER
4
3862 电池盖 Battery
cover
PA6+30GF 1
2.3.Pendulum assembly
6

NO
.
NAME Material TY
1 862 摆体 Pendulum AC43A 1
2862 紫铜片 Red copper sheet T2 1
3hex socket set screws with
flat point GB ,M3*8
45# 4
4 GB_FASTENER_SCREWS_HSFP M3X5-N 45# 4
5hex socket set screws with
flat point gb,M5*12
SUS304 4
6872 轴承 deep groove ball bearings gb 4
7872 中心轴 1 center shaft-1 SUS304 1
8872 压圈 /pressure ring HPb59-1 4
872 中心轴 2center shaft-2 SUS304 1
10 862 顶板 roof ADC-12 1
11 hexagon socket set screws with cup point GB 8
11 862 线激光器 line laser 2
7

13 862 减震垫 rubber shock pad SI
rubber
2
14 872 导电橡胶圈 conductive aprons 1
15 o-rings series a GB Rubber 1
16 875 联线板 On-line plate 1
17 GB_CROSS_SCREWS_TYPE1 M2.5X6 SUS304 1
18 862 主板 main board PCBA 1
19 GB_CROSS_SCREWS_TYPE1 M2.5X5 SUS304 2
20 873 紫铜片联接钉 Copper
sheet screw
2AL12 1
21 GB_FASTENER_SCREWS_HSFP M2.5X4-N SUS304 1
2.4 .Lock seat assembly
8

NO
.
NAME Material TY
1862 锁紧座 Lock seat ABS 1
2892 磁铁 Magnet Magnet 1
3862 右爪 right claw PA6+30GF 1
4862 左爪 left claw PA6+30GF 1
5862 扭簧 Torsional spring 65Mn 1
6 GB_FASTENER_WASHER_SMWC 2.5 sus304 2
7 GB_CROSS_SCREWS_TYPE128
ST2.2X6.5 H C-N
sus304 2
8873 接地端子 terminal q235 1
GB_CROSS_SCREWS_TYPE128
ST2.2X4.5 H C-N
sus304 1
10 862 导电胶布 Conductive TapesB5 1
2.5.Battery box assembly
9

NO
.
NAME Material TY
1862 电池盒 Battery box ABS 1
2872 正极端子 /positive terminal 65Mn 2
3872 弹簧端子 spring terminal 65Mn 2
2.6 Electrical jobs chart
10

3、Common fault and eliminating methods
3.1、Don’t start up
Cause anal sis:
(1) Three dr cells working voltage is lower than 3 V
(2)The power plug contact with the motherboard
(3) The travel switch contact undesirable
Troubleshooting:
(1) Replace the batter in time
(2)Open the shell, reinstall the power plug
(3) Open the shell to adjust the position of the switch chip
Note: ke board or motherboard damage can also cause cannot boot (less likel ),
and to change the contact.
3.2、After startup without laser line
Cause anal sis:
(1) Instrument tilt is too large, be ond the scope of work is the police
(2) laser tube main board attachment poor contact or broken
Troubleshooting:
(1)Adjust the Angle of screw adjust equipment to work within the scope of returned to normal
(2) To open the shell welding laser tube connection
Note: the main board or damage to the laser tube can also be caused no laser line (less likel ), and to
11

change the contact.
3.3、After startup cannot level
Cause anal sis:
(1) The bearing surface is oxidation corrosion
(2) The alarm ring contact surface oxidation b pollution or lead to poor contact
Troubleshooting:
(1) Open the shell, with rust spot bearing replacement
(2) Open the shell, after the alarm ring with anh drous ethanol removal of contamination or oxidation
4、SPEC
12