KaVo ESTETICA E30 User manual

Short instructions for use
ESTETICA E30

Distributed by:
KaVo Dental GmbH
Bismarckring 39
D-88400 Biberach
Tel. [phone]
Fax [phone]
Manufacturer:
Kaltenbach & Voigt GmbH
Bismarckring 39
D-88400 Biberach
www.kavo.com

Table of contents
1 Controls .......................................................................................................................................... 2
1.1 Dentist element TM table ..................................................................................................... 2
1.2 Dentist element S table ........................................................................................................ 2
1.3 Assistant element ................................................................................................................. 3
1.4 Groups of keys ..................................................................................................................... 3
1.5 Foot control .......................................................................................................................... 6
2 Moving the patient chair ................................................................................................................. 7
2.1 Positioning the dental chair manually ................................................................................... 7
2.2 Positioning the patient chair with the foot control ................................................................. 7
2.3 Automatic positioning of patient chair ................................................................................... 7
3 User menu ...................................................................................................................................... 9
3.1 Starting and exiting from the user menu .............................................................................. 9
3.2 Selecting and setting an option .......................................................................................... 10
4 Standby menu .............................................................................................................................. 11
5 Setting the timer ........................................................................................................................... 12
5.1 Select the timer time ........................................................................................................... 12
5.2 Set the timer time ............................................................................................................... 12
6 Setting the handpieces ................................................................................................................. 13
6.1 Adjusting functions ............................................................................................................. 13
6.2 Turbine ............................................................................................................................... 14
6.3 INTRA LUX Motor KL 701 / KL 703 LED ............................................................................ 14
6.4 KL 703 LED in ENDO mode (optional accessories) ........................................................... 15
7 Operate handpieces with the foot control ..................................................................................... 18
8 Hygiene ........................................................................................................................................ 19
8.1 Tumbler filling and bowl flushing ........................................................................................ 19
8.2 Manual hygiene functions of the water-conducting system ................................................ 19
8.3 Manual intensive sterilisation ............................................................................................. 19
8.4 Conditioning the suction system ......................................................................................... 20
8.5 Replenishing Oxygenal ...................................................................................................... 21
9 Troubleshooting / warning signals ................................................................................................ 24
9.1 Safety shut-off .................................................................................................................... 24
9.2 Troubleshooting .................................................................................................................. 25
9.3 Service and error messages in the stand-by menu ............................................................ 26
Table of contents 1

1 Controls
CAUTION
These brief instructions for use only contain the essential operating functions.
They do not substitute for the instructions for use and care that are part of the scope
of delivery.
▶Take note of the instructions for use and care that are part of the scope of de‐
livery.
1.1 Dentist element TM table
FE
ABC D
AGroup of keys for the dental chair DGroup of keys for the menu
BGroup of keys for illumination EGroup of keys for hygiene
CGroup of keys for the handpieces FGroup of keys for the timer
1.2 Dentist element S table
A
BC
D
F
E
AGroup of keys for the menu DGroup of keys for the handpieces
BGroup of keys for illumination EGroup of keys for the timer
CGroup of keys for hygiene FGroup of keys for the dental chair
Controls 2

1.3 Assistant element
AGroup of keys for hygiene CGroup of keys for the timer
BGroup of keys for illumination DGroup of keys for the dental chair
1.4 Groups of keys
Group of keys for the dental chair
The keys of the assistant unit each have two functions and show two symbols.
Assistant unit key Dentist unit key Labelling
"Chair up" key
"AP 0" key
(automatic position 0)
"Chair down" key
"SP" key
(rinsing position)
"LP" key
(last position)
"AP" key
(activate automatic position)
Controls 3

Assistant unit key Dentist unit key Labelling
"Backrest down" key
"AP 1" key
(automatic position 1)
"Backrest up" key
"AP 2" key
(automatic position 2)
"Collapsed position" key
Group of keys for illumination/handpieces
Key Name Control element
Key
"Operating light"
Dentist element and assistant el‐
ement
"Operating light dimming" key Dentist element
Key
"X-ray viewer"
Dentist element
"Direction of motor rotation" but‐
ton
Dentist element
"Preselected spray" button Dentist element
"Cold light" button Dentist element
Group of keys for hygiene
Key Name Control element
"Tumbler filler" key Dentist element and assistant
element
"Bowl rinsing" key Dentist element and assistant
element
Controls 4

Key Name Control element
"Bell" key Dentist element and assistant
element
"Intensive disinfection" key Assistant element (unassigned
key)
"HYDROclean" key Assistant element (unassigned
key)
Group of keys for the menu
Group of keys for the menu
① Menu function selection keys ② Display
Group of keys for the timer
Key Name Control element
"Remote Control" key unassigned key
"Additional motor drives" key dentist element only
"Timer 1" key Dentist element and assistant
element
Controls 5

1.5 Foot control
3
2
1
5
4
Item Name with mounted
handpiece
with removed
handpiece
① "LP/preselected spray" foot-
operated button
Drives dental chair to previ‐
ous position
optional. Sets the spray pre-
selection.
② U-shaped switch Switches the foot-operated
buttons to the "Chair motion"
function.
③ "SP/blown air" foot-operated
button
Drives dental chair to rinsing
position.
optional. Sets the preset
blown air at the dental instru‐
ment (does not apply to
PiezoLED).
④ "Chair position/direction of
motor rotation" 4-way switch
Changes the position of the
dental chair.
Selects the direction of motor
rotation (for KL 701 / KL 703
motor).
⑤ "Preselection of level/hand‐
pieces" foot-operated button
Preselection of level Starts the handpieces and
controls the speed/intensity
of the handpieces.
"Chair position" cross switch
① Chair up ③ Chair down
② Backrest up ④ Backrest down
Controls 6

2 Moving the patient chair
2.1 Positioning the dental chair manually
Key Function
The chair moves up.
The chair moves down.
The backrest moves upward.
The backrest moves downward.
2.2 Positioning the patient chair with the foot control
See also: 1.5, Foot control, Page 6
2.3 Automatic positioning of patient chair
Recalling automatic position through the dentist element
▶ Briefly press the desired button.
Chair automatically moves to the saved position.
Upon arrival at the saved position, the display diode on the button is turned on.
Saving the automatic position through the dentist element
▶ Move the chair to the desired position.
▶ To save the chair position, press the "AP 0", "AP 1", "AP 2", "SP" or "Collapsed po‐
sition" button until you hear a signal.
The display diode of the pressed button is turned on. The chair position is saved.
Recalling an automatic position through the assistant element
▶ Briefly press the "AP" key.
Moving the patient chair 7

The LEDs of the "AP 0", " AP 1", " AP 2", "SP", and "LP" keys flash for approxi‐
mately four seconds.
▶ During these four seconds, briefly press the "AP 0", " AP 1", " AP 2", "SP" or "LP"
key.
The chair moves into the selected automatic position.
Saving an automatic position through the assistant element
▶ Move the chair to the desired position.
▶ Briefly press the "AP" key.
The LEDs of the "AP 0", " AP 1", " AP 2", "SP", and "LP" keys flash for approxi‐
mately four seconds.
▶ During these four seconds, press the "AP 0", "AP 1", "AP 2", "SP" or "LP" button,
until a signal sound is issued.
The display diode of the pressed button is turned on. The chair position is saved.
Recalling an automatic position through the foot control
▶ Press the "SP" foot switch.
or
▶ Press the "LP" foot switch.
The chair moves into the selected automatic position.
Saving an automatic position with the foot control
▶ Hold down the foot pedal and foot-operated button "SP", and simultaneously press
any button for an automatic position ("AP 0", "AP 1", "AP 2" or "SP") on the dentist
or assistant unit until you hear a beep.
The automatic position is saved for the foot-operated button.
or
▶ Hold down the foot pedal and foot-operated button "LP", and simultaneously press
any button for an automatic position ("AP 0", "AP 1", "AP 2" or "SP") on the dentist
or assistant unit until you hear a beep.
The automatic position is saved for the foot-operated button.
Moving the patient chair 8

3 User menu
The following options can be opened in the user menu:
Option Function Description
1 Users Set number of users.
2 Tumbler Set tumbler filling time.
3 Bowl Set bowl rinsing time.
4 Handpiece light Set cold light afterglow period.
5 ENDO Set ENDO holder.
Available only if an ENDO dongle is present.
6 Time of day Set time of day.
7 Date Set date.
8 Time / date display mode Set display mode for time of day and date:
▪ Time of day only
▪ Time of day without seconds
▪ Time of day and date
▪ Date only
9 LCD Set contrast of LCD display.
10 Language Set menu language:
▪ Deutsch
▪ English
▪ Italiano
▪ Français
▪ Castellano
11 Firmware Display current firmware version.
3.1 Starting and exiting from the user menu
Group of keys for the menu
① Menu function selection keys ② Display
▶ Press the "Next" key (S4) to start-up the user menu.
The user menu displays options and parameters. These can be adjusted and changed by the user.
▶ Press the "Save" (S1) key to save the selection made.
User menu 9

Option 1: Set number of users
S1 S2 S3 S4 S1 S2 S3 S4
▶ Press button "S1", "S2", "S3".
Users 1, 2 or 3 will be selected.
▶ Press "S4" button.
2. level is displayed. Users 4 – 6 can be selected.
▶ Press button "S1", "S2", "S3".
Users 4, 5 or 6 will be selected.
3.2 Selecting and setting an option
S1 S2 S3 S4
▶ Press the "Increase value" and "Decrease value" keys to select the desired param‐
eter or value.
See also: Instructions for useESTETICA E30
User menu 10

4 Standby menu
The stand-by menu is used to start the device.
The device switches to the stand-by menu upon closing of the handpiece and endo menus.
S1 S2 S3 S4
▶ Press the "Next" key (S4) to start-up the user menu.
The user menu displays options and parameters. These can be adjusted and changed by the user.
▶ Press the "Save" (S1) key to save the selection made.
Standby menu 11

5 Setting the timer
5.1 Select the timer time
▶ Press the "Timer" key briefly to start or stop the timer.
LED flashes while the timer counts down.
5.2 Set the timer time
▶ Press the "Timer" key for an extended period of time to start the timer programming mode. The pro‐
gramming mode can be started in the stand-by menu only.
S1 S2 S3 S4
Key Settings
S1 Saves the parameters
Closes the settings menu
S2 Changes the value
S3 Changes the value
S4 Switches counter/timer function
Setting the timer 12

6 Setting the handpieces
6.1 Adjusting functions
▶ Settings can be changed using the corresponding keys on the control panel or on the foot control.
Motor speed is set with the foot control only.
The direction of motor rotation, cooling status and light intensity are set with the foot control or the
control keys.
The current settings are saved and activated the next time the handpiece is taken out.
Setting Actuation Pane
Motor speed Foot control Display
Light intensity Foot control, control keys Display
Direction of motor rotation Foot control, control keys LED control keys
Spray status Foot control, control keys LED control keys
Saving the values
▶ Press the "Save" key to save the values. You can save after setting each value, or
after setting all values.
Saving is acknowledged by a beep.
speed/intensity
▶ Remove the handpiece (e.g. turbine, motor, etc.) from the holder.
The handpiece is active.
▶ Press the foot pedal.
The removed handpiece runs at the set speed or intensity.
▶ Changing speed or intensity with the foot pedal.
The left stop corresponds to the minimum speed/intensity.
The right stop corresponds to the maximum speed/intensity.
Setting the light intensity
Only the spray status and light intensity can be set for air instruments.
Setting the handpieces 13

▶ Press the button for "light intensity" (S4) to set the light intensity from 1 to 9 (ring counter).
S1 S2 S3 S4
Setting the direction of motor rotation
Note
The rotational direction of the motor can only be changed when the motor is at rest.
▶ Take motor off the holder.
The handpiece is active.
▶ Press "Motor rotational direction" on the dentist element.
The direction of motor rotation is reversed each time the switch is actuated: coun‐
terclockwise rotation - clockwise rotation.
The direction of motor rotation is displayed on the dentist element.
Setting the cooling level
▶ Remove the handpiece (such as turbine, motor) from the holder.
The handpiece is active.
▶ Press the "Preselected spray" button on the dentist element.
The cooling status is switched each time the button is pressed: air - spray.
The cooling level is displayed on the dentist and assistant element.
6.2 Turbine
The following settings can be changed with the foot control:
▪ Speed
▪ Cooling status
▪ Cold light intensity
6.3 INTRA LUX Motor KL 701 / KL 703 LED
The following settings can be changed in the menu:
▪ Direction of motor rotation
▪ Spray status
▪ Light on/off
Setting the handpieces 14

The following settings can be changed with the foot control:
▪ Direction of motor rotation
▪ Speed
▪ Cold light intensity
▪ Spray status
▪ Light on/off
6.4 KL 703 LED in ENDO mode (optional accessories)
Note
The functions of the ENDO menu are available only if an ENDO dongle is present.
Start-up ENDO menu
The ENDO menu is started-up through:
▪ taking the ENDO motor out of the dentist element (setting in user menu, option 5).
▪ activating the (M) "Additional motor drives" key afterwards.
S1 S2 S3 S4
Key Settings
S1 Saves the parameters
Selects the ENDO menu
S2 Changes the value
S3 Changes the value
S4 Moves the flashing cursor
Torque mode, speed, torque, torque mode, .. (ring counter)
▶ Press the "S1" key for an extended time to select the ENDO settings menu. The individual parame‐
ters can be set and changed in this menu.
Setting the handpieces 15

Setting options
▶ Press the "S4" key to select the ENDO options menu.
S1 S2 S3 S4
Parameters Values
Transmission factor 1:1, 3:1
Parameter memory P1,P2,P3,P4,P5,P6
Torque mode TQ-Ctrl, Autoreverse, AutoRev/Forw.
Direction of motor rotation R, L
Speed 100 to 6,000 rpm
Torque Transmission ratio 1:1: 0.15 to 2.50 Ncm
Transmission ratio 3:1: 0.4 to 8.0 Ncm
The following parameters can be changed:
▪ Speed
▪ Torque
▪ Torque mode
Speed
The speed can be adjusted as follows:
▪ in steps of ten:
in the range from 100 rpm to 500 rpm
▪ in steps of fifty:
in the range from 500 rpm to 1,000 rpm
▪ in steps of 100:
in the range from 1,000 rpm to 6,000 rpm
Torque
1:1 transmission ratio
The torque can be changed as follows:
▪ in steps of 0.05 Ncm:
in the range from 0.15 Ncm to 2.5 Ncm
▪ in steps of 2%:
in the range from 1 % to 100 %
3:1 transmission ratio
Setting the handpieces 16

The torque can be changed as follows:
▪ in steps of 0.05 Ncm:
in the range from 0.4 Ncm to 8 Ncm
▪ in steps of 2%:
in the range from 1 % to 100 %
Torque mode
Three different torque modes are available:
▪ Torque only
▪ Autoreverse
▪ Autoreverse / Forward
Setting the handpieces 17

7 Operate handpieces with the foot control
▶ Remove the handpiece (such as turbine, motor) from the holder.
The handpiece is active.
▶ Press the foot pedal.
The removed handpiece runs at the set speed or intensity.
▶ Changing speed or intensity with the foot pedal.
The left stop corresponds to the minimum speed/intensity.
The right stop corresponds to the maximum speed/intensity.
Preselect counterclockwise motor rotation
▶ Take motor off the holder.
The handpiece is active.
▶ Slide the cross switch upward.
The direction of motor rotation is reversed each time the cross-switch is actuated:
counterclockwise rotation - clockwise rotation.
The direction of motor rotation is displayed on the dentist element.
Setting the instrument light
▶ Slide the cross switch to the right. (spotlight function)
Cold light "On" (even when Cold light: "Off" is preselected).
▶ Slide the cross switch to the left.
Change the cold light status: "On/Off"
Operate handpieces with the foot control 18