KaVo ESTETICA E70 Vision Installation guide

Care instructions
ESTETICA E70 Vision / E80 Vision

Distributed by:
KaVo Dental Technologies, LLC
11727 Fruehauf Drive
Charlotte, NC 28273 USA
Tel. [phone]
Fax [phone]
Manufacturer:
Kaltenbach & Voigt GmbH
Bismarckring 39
88400 Biberach
Germany
www.kavo.com

Table of contents
1 User instructions ................................................................................................................ 4
1.1 User guide .................................................................................................................... 4
1.1.1 Abbreviations ..................................................................................................... 4
1.1.2 Symbols ............................................................................................................ 4
1.1.3 Target group ...................................................................................................... 4
2 Setup methods according to ISO 17664 ............................................................................ 5
2.1 instructions ................................................................................................................... 5
2.2 General instructions for the reprocessing of KaVo treatment units....................................... 6
2.2.1 Overview of ESTETICA E70 Vision / E80 Vision reprocessing.................................... 8
2.3 Reprocessing of the surfaces of treatment centre / upholstery............................................ 9
2.4 Preparation of the dentist unit......................................................................................... 11
2.4.1 Preparation of the handle and holder pad/ anti-slip mat .......................................... 11
2.4.2 Preparing the instrument holder ........................................................................... 12
2.4.3 Reprocessing of the swing-arm S table (E70 Vision only) ........................................ 13
2.4.4 Setting up the triple-function and multifunction handpiece ...................................... 14
2.4.5 Preparation of the instrument hoses ..................................................................... 17
2.4.6 Servicing the turbine return air filter ..................................................................... 17
2.4.7 Reprocessing of the kit for physiological saline solution and surgical motor ............... 18
2.4.8 Reprocessing KaVo ERGOcam One ....................................................................... 22
2.5 Preparation of the assistant unit ...................................................................................... 23
2.5.1 Preparing the instrument holder ........................................................................... 23
2.5.2 Preparing the connector for the suction hose ......................................................... 24
2.5.3 Reprocessing of sieve inserts and suction hoses ..................................................... 25
2.5.4 Preparation of the sleeve of the Aquamat device .................................................... 26
2.6 Reprocessing of the patient element (optional) ................................................................. 26
2.6.1 Preparation of the tumbler................................................................................... 27
2.6.2 Preparation of the tumbler holder and filler............................................................ 27
2.6.3 Preparation of the spittoon................................................................................... 28
2.7 Automatic cleaning programmes ..................................................................................... 29
2.7.1 Preparation of the cleaning programmes ............................................................... 29
2.7.2 Discontinuing a cleaning programme .................................................................... 32
2.7.3 Cleaning programme, "After treatment" ................................................................ 32
2.7.4 Cleaning programs "Morning" and "Evening".......................................................... 33
2.7.5 "Weekly" cleaning programme ............................................................................. 34
2.7.6 Manual internal cleaning of the suction hoses......................................................... 37
2.8 Reprocessing of the handpiece holder .............................................................................. 37
2.9 Preparation of the amalgam separator ............................................................................. 39
2.10Reprocessing KaVo Screen One / KaVo Screen HD ............................................................ 39
2.11Reprocessing of the service table 1568 ............................................................................ 40
3 Replacing and checking cleaning and germ reduction agents ...........................................41
3.1 Replace the DEKAPURE Gel cleaner.................................................................................. 41
3.2 Replace the OXYGENAL 6 cleaner .................................................................................... 42
3.3 Check the OXYGENAL 6 concentration.............................................................................. 43
Care instructions ESTETICA E70 Vision / E80 Vision
Table of contents
3 / 48

Care instructions ESTETICA E70 Vision / E80 Vision
1 User instructions | 1.1 User guide
4 / 48
1 User instructions
1.1 User guide
Requirement
Read these instructions prior to first startup to avoid misuse and prevent dam-
age.
Note
Comply with the Instructions for Use of the treatment unit!
1.1.1 Abbreviations
Ab-
brevi-
ation
Explanation
IfU Instructions for use
CI Care instructions
AI Assembly instructions
TI Technician's instructions
SC Safety checks
IEC International Electrotechnical Commission
RI Repair instructions
EMC Electromagnetic compatibility
Scaler Scaler (ZEG)
IR Infrared
IrDA Infrared Data Association
1.1.2 Symbols
Refer to the chapter on Safety/Warning symbol
Important information for users and service technicians
Action request
CE mark according to Medical Devices Directive EC 93/42
Thermodisinfectable at up to 95 °C (203 °F)
Suitable for steam sterilisation at up to 135 oC (275 °F)
1.1.3 Target group
This document is for dentists and dental office staff.

Care instructions ESTETICA E70 Vision / E80 Vision
2 Setup methods according to ISO 17664 | 2.1 instructions
2 Setup methods according to ISO 17664
2.1 instructions
The reprocessing consists of the following basic steps:
▪ Cleaning and disinfection ( manually or automatically)
▪ Sterilisation
Note
Comply with national hygiene requirements, e.g. RKI guidelines.
CAUTION
Risk of injury during cleaning of the treatment unit.
Lack of instructions to the cleaning staff and lack of preparation of the treat-
ment unit can lead to the cleaning personnel sustaining injuries.
▶Only trained professionals and instructed cleaning personnel may be
present in the treatment rooms.
▶Position the chair for cleaning and turn the device off.
NOTICE
Product damage due to improper disinfection.
Malfunctions.
▶Use the disinfectant according to the specifications of the manufacturer.
▶No spray disinfection, perform wipe disinfection only.
▶Do not immerse product or parts of the product in liquids.
▶Mop up any spilled cleanser or disinfectant immediately.
CAUTION
Improper disinfection may lead to health hazards and material dam-
age.
Infection hazard to users and patients.
Damage to the sterile product.
▶No hot air sterilisation, no chemical cold sterilisation, do not sterilise with
ethylene oxide.
CAUTION
Health hazard and property damage due to non-compliance with servi-
cing schedule.
Infection hazard to users and patients.
Product damage.
▶Comply with servicing schedule.
Note
The preparation methods for the instruments and motors are found in the
separate instructions for use that accompany the instrument and motor
packages.
5 / 48

Care instructions ESTETICA E70 Vision / E80 Vision
2 Setup methods according to ISO 17664 | 2.2 General instructions for the reprocessing of KaVo treatment units
6 / 48
Note
Dental Handpieces, Instruments and Accessories
Please refer to respective manufacturer’s Instructions for Use (IFU) for ap-
propriate cleaning, disinfecting and sterilization requirements. These include,
but not limited to, pneumatic handpieces, electric motors with handpieces,
scalers, intra-oral cameras, curing lights, air/water syringes and SE and HVE
vacuum instruments.
Note
It is essential to comply with the hygiene requirements (sterility) during the
test after reprocessing. If sites of fracture and clear changes of the surface
are visible, the parts need to be checked by the Service.
2.2 General instructions for the reprocessing of KaVo
treatment units
Please comply with the general reprocessing instructions at all times. Detailed
product-specific reprocessing instructions are provided subsequently.
At the site of use ▶Remove any surface contamination using a disposable cloth/pa-
per towel.
Storage and transport KaVo recommends reprocessing as soon as possible after use.
Preparations for cleaning ▶Comply with product-specific reprocessing instructions.
Manual cleaning Fixtures:
▪ Brush or cloth
▪ Tap water 30 °C ± 5 °C
▶Remove any dirt on the surface using a suitable cleanser accord-
ing to the recommendations of the manufacturer. Before doing
so, check the compatibility of the cleanser on a inconspicuous
place of the treatment centre.
Automatic cleaning KaVo recommends washer disinfectors in compliance with ISO
15883-1, which are operated using alkaline cleaning agents.
▶For programme settings as well as cleansers and disinfectants to
be used, please refer to the Instructions for Use of the washer
disinfector.
▶Directly after automated cleaning/disinfection, treat the medical
device with the care products and systems provided by KaVo.
Manual disinfection ▶Perform wipe disinfection only, the use of spray disinfection and
disinfection baths is not feasible.
▶Wipe all outer surfaces with a soft cloth and an approved disin-
fectant.
Approved disinfectants:
▪ CaviCide / CaviWipes (Metrex)
▶Use disinfectants according to the manufacturer's Instructions for
Use.
▶Please note the disinfectant safety data sheet.

Care instructions ESTETICA E70 Vision / E80 Vision
2 Setup methods according to ISO 17664 | 2.2 General instructions for the reprocessing of KaVo treatment units
Automatic disinfection KaVo recommends washer disinfectors in compliance with ISO
15883-1, which are operated using alkaline cleaning agents.
▶For programme settings as well as cleansers and disinfectants to
be used, please refer to the Instructions for Use of the washer
disinfector.
▶In order to prevent negative effects on the medical device, make
sure that the interior and the exterior of the medical device are
dry after completion of the cycle, and then grease it immediately
with servicing agents from the KaVo care system.
Manual drying ▶Supply dry, clean and uncontaminated compressed air according
to ISO 7494-2 only.
▶Blow off the outside and inside with compressed air until water
drops are no longer visible.
Automatic drying Usually, automatic drying is part of the cleaning/disinfection cycle of
the washer disinfector and should not be carried out above 95 °C.
Servicing ▶Discard damaged products.
Control and functional test ▶Perform a visual inspection to check for damage and wear and
tear.
▶Test products for function regularly.
Packaging ▶Use standardised packaging material. Sealing should not be un-
der tension.
▶Use sterile goods packaging in order to ensure sterility.
Sterilisation All sterilisable products are temperature-resistant up to max. 138
°C.
Select a suitable procedure (depending on the available autoclave)
from the following sterilisation processes:
▪ Autoclave with three times pre-vacuum:
- at least 3 minutes at 134 °C -1 °C / +4 °C (273 °F -1.6 °F /
+7.4 °F)
▪ Autoclave using the gravity method:
- at least 10 minutes at 134 °C -1 °C / +4 °C (273 °F -1.6 °F /
+7.4 °F)
▶Use according to the manufacturer's Instructions for Use.
Storage ▶Reprocessed products should be stored protected from dust with
minimum exposure to germs in a dry, dark and cool place.
▶Comply with the expiry date of the sterilised items.
7 / 48

Care instructions ESTETICA E70 Vision / E80 Vision
2 Setup methods according to ISO 17664 | 2.2 General instructions for the reprocessing of KaVo treatment units
8 / 48
2.2.1 Overview of ESTETICA E70 Vision / E80 Vision
reprocessing
Reprocessing items/medical
devices
Cleaning Disinfection Sterilisa-
tion
manual automatic manual automatic automatic
Surfaces
Equipment
Cushion
Gripping sleeve, white
Gripping sleeve, grey
Light
Monitor
Dentist element
Handpiece sleeve of the three-func-
tion or multifunctional handpiece
Cannula of the three-function or mul-
tifunctional handpiece
Holder pad/anti-slip mat
Handpiece holder
Swing-arm S-table
Instrument tray for surgery assembly
kit
Intraoral camera
Assistant element
Connection parts of the suction hose
Patient element
Tumbler support
Tumbler filler
Glass spittoon bowl
Porcelain spittoon bowl
Handpiece holder of the hygiene
centre

Care instructions ESTETICA E70 Vision / E80 Vision
2 Setup methods according to ISO 17664 | 2.3 Reprocessing of the surfaces of treatment centre / upholstery
2.3 Reprocessing of the surfaces of treatment centre /
upholstery
Position the chair for cleaning
▶Tap the "Cleaning position" button in the "Cleaning" tab to drive the chair
into the cleaning position.
See also:
2Instructions for use of the treatment centre
Locking the touchscreen
▶Tap the "Lock screen" button on the dentist element or the KaVo Logo on
the assistant element to lock the screen for wiping with a disinfectant.
ðThe following display is shown on the dentist element:
Cleaning and disinfecting the surfaces of treatment
unit / upholstery
NOTICE
Non-colour-fast textiles.
Non-colour-fast textiles can cause permanent discoloration.
▶Remove discolorations with water immediately.
9 / 48

Care instructions ESTETICA E70 Vision / E80 Vision
2 Setup methods according to ISO 17664 | 2.3 Reprocessing of the surfaces of treatment centre / upholstery
10 / 48
▶Clean the surfaces and upholstery with a soft cloth and water, and wipe-dis-
infect them with an approved surface disinfectant.
Approved disinfectants:
▪ CaviCide / CaviWipes (Metrex)
NOTICE
Damage caused by spray disinfection.
Disinfectant gets into cracks and loosens the paint.
▶Do not use spray disinfection.
▶Only disinfect by wiping.
Cleaning and disinfection of the foot control
NOTICE
Damage caused by inappropriate use of water.
Damage to the foot control.
▶For cleaning, the foot control must not be immersed in water or placed un-
der running water.
▶When wiping it off with a moist cloth, do not touch the contacts of the
charge socket.
▶Only wipe off. Do not spray.

Care instructions ESTETICA E70 Vision / E80 Vision
2 Setup methods according to ISO 17664 | 2.4 Preparation of the dentist unit
2.4 Preparation of the dentist unit
2.4.1 Preparation of the handle and holder pad/ anti-
slip mat
Cleaning and disinfection of the handle and holder pad/
antislip mat (T table / S table)
▶Press the push button and pull off the handle.
▶Clean the handle under flowing water.
▶Disinfect the white and grey handle by wiping or thermodisinfection (minor
discolouration may occur).
▶Sterilise the holder pad and anti-slip mat by thermodisinfection.
Sterilisation of the handle and holder pad/ anti-slip mat
(T table / S table)
CAUTION
Damage caused by sterilisation.
▶Do not sterilise the white standard handle.
▶Sterilise the holder pad/ anti-slip mat.
The grey handle (Mat. no. 1.002.4489) can be sterilised (see symbol on the
handle).
11 / 48

Care instructions ESTETICA E70 Vision / E80 Vision
2 Setup methods according to ISO 17664 | 2.4 Preparation of the dentist unit
12 / 48
2.4.2 Preparing the instrument holder
Note
The handpiece tray with 5-handpieces holder (Mat. no. 30014236) and
with 6-handpieces holder (Mat. no. 30014251) can be removed for easier
cleaning.
Cleaning and disinfection of the instrument holder
NOTICE
Damage caused by treatment in a washer disinfector.
▶Do not treat the instrument holder in a washer disinfector.
▶Place the handpiece hoses in the designated places of the hygiene centre
during the cleaning and germ reduction of the handpiece holder.
▶Pull the latches evenly outward and carefully remove the handpiece tray.
▶Clean the handpiece tray under running water.
▶Wipe-disinfect the instrument holder.

Care instructions ESTETICA E70 Vision / E80 Vision
2 Setup methods according to ISO 17664 | 2.4 Preparation of the dentist unit
Sterilize the instrument holder
NOTICE
Damage caused by sterilisation.
▶Do not sterilise the instrument holder.
2.4.3 Reprocessing of the swing-arm S table (E70 Vision
only)
Note
The swing-arm S-table (Mat. no. 10074755)) can be removed to facilitate
cleaning.
Cleaning and disinfection of the instrument arm S table
NOTICE
Damage caused by treatment in a washer disinfector.
▶Do not sterilise the instrument arm S table in a washer disinfector.
Note
No cleaning programmes can be run when the swing-arm is removed.
▶Locking the screen.
See also:
2Locking the touchscreen, Page 9
▶Take the handpieces off the hoses.
▶Take the roller out of the swing-arm and then place the hose in the hygiene
centre.
▶Pull-off the swing-arm in an upward direction.
▶Clean the swing-arm and roller under running water.
13 / 48

Care instructions ESTETICA E70 Vision / E80 Vision
2 Setup methods according to ISO 17664 | 2.4 Preparation of the dentist unit
14 / 48
▶Wipe the instrument arm S table with disinfectant.
Sterilisation of instrument arm S table
NOTICE
Damage caused by sterilisation.
▶Do not sterilise the instrument arm S table.
2.4.4 Setting up the triple-function and multifunction
handpiece
Note
Wet the O-rings of the gripping sleeves after sterilisation using silicone
grease (Mat. no. 1.000.6403) or KaVo Rota Spray 2 (Mat. no.
0.411.7510). After replacing the cannula, the air channel must be blown out
before the start of treatment to ensure that the air exiting during treatment
is dry.
Cleaning the triple-function and multifunction handpiece
Automatic cleaning
Not applicable.
NOTICE
Damage caused by improper cleaning/disinfection.
▶Do not wash the gripping sleeve and the cannula in the washer disinfector.
▶Do not sterilise the gripping sleeve and the cannula in the hot-air steriliser.
▶Do not place the gripping sleeve and the cannula in a disinfectant or ultra-
sonic bath.
Manual cleaning
Note
Combine manual cleaning with disinfection.
Cleaning the interior
▶Leave the gripping sleeve and cannula on the instrument, and activate the
air and water for 60 seconds.
External cleaning
CAUTION
Danger of injury if the valve body is hot (heating elements, high-pres-
sure lamp).
Risk of burn injury.
▶Switch off the unit at the main switch.
▶Let the handpiece cool after long use.

Care instructions ESTETICA E70 Vision / E80 Vision
2 Setup methods according to ISO 17664 | 2.4 Preparation of the dentist unit
Accessories required:
▪ Tap water 30oC ± 5oC
▪ Brush, e.g. medium-hard toothbrush
▶Disassemble the gripping sleeve and cannula.
▶Detach the key part from the gripping sleeve.
▶Clean the key part, gripping sleeve and cannula by brushing them under
running water (at least tap water quality).
▶Immediately remove contamination from materials used in the dental prac-
tice (impression materials, caustic chemicals).
▶Carefully wipe off contamination from the cannula tip with a soft Q-tip or
soft cloth and water.
NOTICE
Damage caused by using a nozzle needle that is too long.
Damage to the internal hoses of the cannula.
▶Use a short nozzle needle (Mat. no. 1.004.4986) to clean the media exit
holes.
▶Carefully remove contamination from the media exit ports using the short
nozzle cleaning needle.
Disinfection of the triple-function and multifunction
handpiece
Manual disinfection
External disinfection
▶Wipe-disinfect the surfaces with a soft cloth.
Automatic disinfecting
Not applicable.
NOTICE
Damage caused by improper cleaning/disinfection.
▶Do not wash the gripping sleeve and the cannula in the washer disinfector.
▶Do not sterilise the gripping sleeve and the cannula in the hot-air steriliser.
▶Do not place the gripping sleeve and the cannula in a disinfectant or ultra-
sonic bath.
15 / 48

Care instructions ESTETICA E70 Vision / E80 Vision
2 Setup methods according to ISO 17664 | 2.4 Preparation of the dentist unit
16 / 48
Drying the triple-function and multifunction handpiece
Manual drying
▶Blow off the outside and inside with compressed air until water drops are no
longer visible.
Automatic drying
Not applicable.
Care of the triple-function and multifunctional
handpiece
Requirement
The multifunctional handpiece has been reprocessed.
▶Apply KaVo silicone grease (Mat. no. 1.000.6403) or KaVo Rota Spray 2
(Mat. no. 0.411.7510) to the O-rings of the joint between the gripping
sleeve and cannula. Use cotton buds for this purpose.
Sterilising the triple-function and multifunction
handpiece
Note
The grip sleeve and cannula can be sterilised.
▶Hold the 3-way or multifunctional handpiece at the gripping sleeve and take
off the cannula with a slight twisting motion.
▶Pull the gripping sleeve off the valve body.

Care instructions ESTETICA E70 Vision / E80 Vision
2 Setup methods according to ISO 17664 | 2.4 Preparation of the dentist unit
Sterilisation in a steam sterilizer in compliance with ISO
13060
▶Weld the cannula and grip sleeve in sterile goods packaging.
▶Sterilise with a triple fractionated vacuum (B class steriliser); hold for 4
minutes; 134°C ± 1 °C; overpressure: 2.13 bar.
NOTICE
Damage caused by over-heating.
Damage to the gripping sleeve.
▶Immediately remove the parts from the steriliser after the sterilisation cycle
is completed.
Storage
▶Reprocessed products should be stored protected from dust with minimum
exposure to germs in a dry, dark and cool place.
2.4.5 Preparation of the instrument hoses
Cleaning and disinfection of instrument hoses
▶Clean the hoses and couplings with a cloth and water.
NOTICE
Damage caused by spray disinfection.
▶Do not subject instrument hoses to spray disinfection.
▶Subject instrument hoses to wipe disinfection.
2.4.6 Servicing the turbine return air filter
Cleaning the turbine return air filter
Note
The liquid collector must be checked weekly.
▶If there is any liquid in the filter, drain the liquid and replace the O-rings of
the multiflex couplings.
17 / 48

Care instructions ESTETICA E70 Vision / E80 Vision
2 Setup methods according to ISO 17664 | 2.4 Preparation of the dentist unit
18 / 48
▶If necessary, replace the turbine return air filter (Mat. no. 0.200.3098)
and clean the filter holder.
Note
The turbine return air filter is in the same position in the dentist element vari-
ant with S table.
2.4.7 Reprocessing of the kit for physiological saline
solution and surgical motor
The kit for the physiological saline solution and surgery motor are optional.
Note
The reprocessing steps for surgical motors with motor cable and for the
straight and contra-angle handpieces are described in the corresponding In-
structions for use.
Note
The reprocessing instructions have been validated by the manufacturer. Any
departure from the instructions provided must be checked by the repro-
cessing entity for efficacy and possible detrimental consequences.
Cleaning the kit for physiological saline solution
Manual cleaning
▶Use a soft disposable cloth to wipe down all visible surfaces of the unit,
bottle holder, foot control surfaces, and connecting cables.

Care instructions ESTETICA E70 Vision / E80 Vision
2 Setup methods according to ISO 17664 | 2.4 Preparation of the dentist unit
Machine cleaning
NOTICE
Damage by liquids.
Faults on electrical components.
▶Do not machine-clean the device.
The following parts of the unit are released for machine-based cleaning:
▪ Handpiece tray
▪ Motor and motor cable
Note
Please comply with the corresponding Instructions for use when you re-pro-
cess the motor and motor cable.
The re-processing steps for the handpiece tray are as follows:
KaVo recommends washer disinfectors according to ISO 15883-1, which are
operated using alkaline cleaning agents.
▶For program settings as well as cleansers and disinfectants to be used,
please refer to the Instructions for Use of the thermodisinfector.
Disinfection of the assembly kit for physiological saline
solution
Note
After each treatment of a patient, the surfaces near the patient that may
have been contaminated by contact or aerosol need to be disinfected. All dis-
infection measures need to be carried out by wipe disinfection.
Note
Please comply with the corresponding Instructions for use when you re-pro-
cess the motor and motor cable.
Manual disinfection
▶Use a soft disposable cloth and an approved disinfectant for disinfection by
wiping down all visible surfaces of the unit, bottle holder, foot control sur-
faces, and connecting cables. Make sure that all surfaces are wetted.
▶Let the disinfectant act for the prescribed time.
▶Dry the surfaces.
Permissible disinfectants (application range in accordance with the available
manufacturer's instructions and national guidelines. Please note material safety
data sheets.) KaVo recommends the following products based on the compatib-
ility of the materials. The microbiological efficacy must be confirmed by the dis-
infectant manufacturer.
▪ CaviCide made by Metrex
Automated disinfection
The following parts of the unit are released for machine-based disinfection:
▪ Handpiece tray
19 / 48

Care instructions ESTETICA E70 Vision / E80 Vision
2 Setup methods according to ISO 17664 | 2.4 Preparation of the dentist unit
20 / 48
▪ Motor and motor cable
Note
Please comply with the corresponding Instructions for use when you re-pro-
cess the motor and motor cable.
The re-processing steps for the handpiece tray are as follows:
KaVo recommends washer disinfectors in compliance with ISO 15883-1, which
are operated using alkaline cleaning agents.
▶For program settings as well as cleansers and disinfectants to be used,
please refer to the Instructions for Use of the thermodisinfector.
Drying
Note
Coolant hose with accessories is intended for single use only and is not to be
disinfected and sterilised. No drying required.
▶Allow all disinfected and and sterilised parts to dry fully on room air before
using them again.
Automatic Drying
The drying procedure is normally part of the cleaning program of the thermod-
isinfector.
▶Please observe the instructions for use of the thermodisinfector.
Service, inspection and testing after preparation
Note
It is essential to comply with the hygiene requirements (sterility) during the
test after reprocessing. If sites of fracture and clear changes of the surface
are visible, the parts need to be checked by the Service.
Check for cleanliness, intactness, servicing, and repair as described in the fol-
lowing:
▶Check the adjustable functions of the unit and the motor function.
▶Check the hose pump for sufficient coolant flow rate.
▶Check the control commands on the wireless foot control.
Packaging the assembly kit for physiological saline
solution
Note
The quality and use of the sterilisation packaging must comply with applic-
able standards and be suitable for the sterilisation procedure!
Note
If potentially infectious liquids and particles can contact the products, it is re-
commendable to cover and protect these areas with sterile disposable
products.
▶Seal the handpiece tray and motor cable in a sterilisation pouch.