KaVo KaVo Primus 1058 Life TM Installation guide

Care instructions
Primus 1058 Life

Manufacturer:
Kaltenbach & Voigt GmbH
Bismarckring 39
D-88400 Biberach
www.kavo.com
Distributed by:
KaVo Dental GmbH
Bismarckring 39
D-88400 Biberach
Phone [phone]
Fax [phone]

Table of contents
1 User instructions ................................................................................................................ 4
1.1 User guide .................................................................................................................... 4
1.1.1 Abbreviations ..................................................................................................... 4
1.1.2 Symbols ............................................................................................................ 4
1.1.3 Target group ...................................................................................................... 4
2 Setup methods according to DIN EN ISO 17664................................................................ 5
2.1 References.................................................................................................................... 5
2.2 General instructions for the reprocessing of KaVo treatment units....................................... 6
2.2.1 Reprocessing Overview Primus 1058 Life............................................................... 7
2.3 Reprocessing of the surfaces of treatment unit / upholstery ............................................... 8
2.4 Preparation of the dentist unit......................................................................................... 9
2.4.1 Reprocessing of handle and holder pad/anti-slip mat .............................................. 9
2.4.2 Reprocessing of the instrument holder of the TM table............................................ 11
2.4.3 Reprocessing of the instrument arm S table........................................................... 13
2.4.4 Setting up the 3-function and multifunction handpiece............................................ 14
2.4.5 Preparation of the instrument hoses ..................................................................... 17
2.4.6 Servicing the turbine return air filter ..................................................................... 18
2.4.7 Reprocessing KaVo ERGOcam One ....................................................................... 18
2.5 Reprocessing of the assistant unit.................................................................................... 20
2.5.1 Preparing the instrument holder ........................................................................... 20
2.5.2 Preparing the connector for the suction hose ......................................................... 20
2.5.3 Reprocessing of sieve inserts and suction hoses ..................................................... 21
2.6 Preparation of the patient unit......................................................................................... 21
2.6.1 Preparation of the tumbler................................................................................... 21
2.6.2 Preparation of the tumbler holder and filler............................................................ 21
2.6.3 Preparation of the spittoon................................................................................... 23
2.7 Manual reprocessing of the water-conducting system ........................................................ 24
2.8 Automatic hygiene functions of the water conducting system ............................................. 24
2.8.1 Rinsing programme............................................................................................. 25
2.8.2 Intensive germ reduction..................................................................................... 28
2.9 Reprocessing and automatic hygiene functions of the suction system.................................. 32
2.9.1 Reprocessing of the suction system including suction hoses..................................... 32
2.9.2 HYDROclean function .......................................................................................... 32
2.10Preparation of the amalgam separator ............................................................................. 33
2.11Reprocessing KaVo Screen One / KaVo Screen HD ............................................................ 34
2.12Reprocessing of the service table 1568 ............................................................................ 34
3 Replenish and check the disinfectant.................................................................................36
3.1 Replenish OXYGENAL 6 .................................................................................................. 36
3.1.1 Replenish OXYGENAL 6 when using the water bottle............................................... 37
3.2 Check the OXYGENAL 6 concentration.............................................................................. 40
Care instructions Primus 1058 Life
Table of contents
3 / 44

Care instructions Primus 1058 Life
1 User instructions | 1.1 User guide
4 / 44
1 User instructions
1.1 User guide
Requirement
Read these instructions prior to first use to avoid misuse and prevent damage.
Note
Comply with the Instructions for Use of the Primus 1058 Life treatment unit!
1.1.1 Abbreviations
Ab-
brevi-
ation
Explanation
IfU Instructions for use
CI Care instructions
AI Assembly instructions
TI Technician's instructions
SC Safety checks
IEC International Electrotechnical Commission
RI Repair instructions
EMC Electromagnetic compatibility
Scaler Scaler (ZEG)
IR Infrared
IrDA Infrared Data Association
1.1.2 Symbols
Refer to the chapter on Safety/Warning symbol
Important information for users and service technicians
Action request
CE mark according to Medical Devices Directive EC 93/42
Thermodisinfectable at up to 95 °C (203 °F)
Suitable for steam sterilisation at up to 135 oC (275 °F)
1.1.3 Target group
This document is for dentists and dental office staff.

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.1 References
2 Setup methods according to DIN EN ISO 17664
2.1 References
The reprocessing consists of the following basic steps:
▪ Cleaning and disinfection ( manually or automatically)
▪ Sterilisation
Note
Comply with national hygiene requirements, e.g. RKI guidelines.
CAUTION
Risk of injury during cleaning of the treatment unit.
Lack of instructions to the cleaning staff and lack of preparation of the treat-
ment unit can lead to the cleaning personnel sustaining injuries.
▶Only trained professionals and instructed cleaning personnel may be
present in the treatment rooms.
▶Position the chair for cleaning and turn the device off.
NOTICE
Product damage due to improper disinfection.
Malfunctions.
▶Use the disinfectant according to the specifications of the manufacturer.
▶No spray disinfection, perform wipe disinfection only.
▶Do not immerse product or parts of the product in liquids.
▶Mop up any spilled cleanser or disinfectant immediately.
CAUTION
Improper disinfection may lead to health hazards and material dam-
age.
Infection hazard to users and patients.
Damage to the sterile product.
▶No hot air sterilisation, no chemical cold sterilisation, do not sterilise with
ethylene oxide.
CAUTION
Health hazard and property damage due to non-compliance with servi-
cing schedule.
Infection hazard to users and patients.
Product damage.
▶Comply with servicing schedule.
Note
The preparation methods for the instruments and motors are found in the
separate instructions for use that accompany the instrument and motor
packages.
5 / 44

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.2 General instructions for the reprocessing of KaVo treatment
units
6 / 44
2.2 General instructions for the reprocessing of KaVo
treatment units
Please comply with the general reprocessing instructions at all times. Detailed
product-specific reprocessing instructions are provided subsequently.
At the site of use ▶Remove any surface contamination using a disposable cloth/pa-
per towel.
Storage and transport KaVo recommends reprocessing as soon as possible after use.
Preparations for cleaning ▶Comply with product-specific reprocessing instructions.
Manual cleaning Fixtures:
▪ Brush or cloth
▪ Tap water 30 °C ± 5 °C
▶Remove any dirt on the surface using a suitable cleanser accord-
ing to the recommendations of the manufacturer. Before doing
so, check the compatibility of the cleanser on a inconspicuous
place of the treatment centre.
Automatic cleaning KaVo recommends washer disinfectors from Miele in accordance
with EN ISO 15883-1 that are operated with alkaline cleaning
agents.
The validations were conducted with the VARIO-TD programme, the
cleaning agent neodisher® MediClean and the neutralisation agent
neodisher® Z.
▶For programme settings as well as cleansers and disinfectants to
be used, please refer to the Instructions for Use of the washer
disinfector.
▶Directly after automated cleaning/disinfection, treat the medical
device with the care products and systems provided by KaVo.
Manual disinfection ▶Perform wipe disinfection only, the use of spray disinfection and
disinfection baths is not feasible.
▶Wipe all outer surfaces with a soft cloth and an approved disin-
fectant.
Approved disinfectants:
▪ CaviCide / CaviWipes (Metrex)
▪ Microcide AF Liquid (Schülke & Mayr)
▪ FD 322 (Dürr Dental)
▪ Incidin Liquid (Ecolab)
▶Use disinfectants according to the manufacturer's Instructions for
Use.
▶Please note the disinfectant safety data sheet.
Automatic disinfection KaVo recommends washer disinfectors from Miele in accordance
with EN ISO 15883-1 that are operated with alkaline cleaning
agents.
The validations were conducted with the VARIO-TD programme, the
cleaning agent neodisher® MediClean and the neutralisation agent
neodisher® Z.
▶For programme settings as well as cleansers and disinfectants to
be used, please refer to the Instructions for Use of the washer
disinfector.
▶In order to prevent negative effects on the medical device, make
sure that the interior and the exterior of the medical device are
dry after completion of the cycle, and then grease it immediately
with servicing agents from the KaVo care system.

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.2 General instructions for the reprocessing of KaVo treatment
units
Manual drying ▶Supply dry, clean and uncontaminated compressed air according
to ISO 7494-2 only.
▶Blow off the outside and inside with compressed air until water
drops are no longer visible.
Automatic drying Usually, automatic drying is part of the cleaning/disinfection cycle of
the washer disinfector and should not be carried out above 95 °C.
Servicing ▶Discard damaged products.
Control and functional test ▶Perform a visual inspection to check for damage and wear and
tear.
▶Test products for function regularly.
Packaging ▶Use standardised packaging material. Sealing should not be un-
der tension.
▶Use sterile goods packaging in order to ensure sterility.
Sterilisation All sterilisable products are temperature-resistant up to max. 138
°C.
Select a suitable procedure (depending on the available autoclave)
from the following sterilisation processes:
▪ Autoclave with three times pre-vacuum:
- at least 3 minutes at 134 °C -1 °C / +4 °C (273 °F -1.6 °F /
+7.4 °F)
▪ Autoclave using the gravity method:
- at least 10 minutes at 134 °C -1 °C / +4 °C (273 °F -1.6 °F /
+7.4 °F)
▶Use according to the manufacturer's Instructions for Use.
Storage ▶Reprocessed products should be stored protected from dust with
minimum exposure to germs in a dry, dark and cool place.
▶Comply with the expiry date of the sterilised items.
2.2.1 Reprocessing Overview Primus 1058 Life
Reprocessing items/medical
devices
Cleaning Disinfection Sterilisa-
tion
manual automatic manual automatic automatic
Surfaces
Unit
Cushion
Gripping sleeve, white
Gripping sleeve, grey
Light
Dentist element
Handpiece sleeve 3F and MF
handpieces
Cannula for 3F and MF hand-
pieces
Holder pad/anti-slip mat
Handpiece holder
Swing-arm S-table
Assistant element
7 / 44

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.3 Reprocessing of the surfaces of treatment unit / upholstery
8 / 44
Reprocessing items/medical
devices
Cleaning Disinfection Sterilisa-
tion
Connection parts of the suction
hose
Patient element
Tumbler support
Tumbler filler
Porcelain spittoon bowl
Glass spittoon bowl
2.3 Reprocessing of the surfaces of treatment unit /
upholstery
Position the chair for cleaning
▶Adjust the backrest to vertical position and move the chair upward.
Also refer to:
Instructions for usePrimus 1058 Life
Turn device off
▶Switch main device switch off.
Cleaning and disinfecting the surfaces of treatment
unit / upholstery
NOTICE
Non-colour-fast textiles.
Non-colour-fast textiles can cause permanent discoloration.
▶Remove discolorations with water immediately.
Approved disinfectants:
▪ CaviCide / CaviWipes (Metrex)
▪ Microcide AF Liquid (Schülke & Mayr)
▪ FD 322 (Dürr Dental)
▪ Incidin Liquid (Ecolab)
▶Clean the surfaces and upholstery with a soft cloth and water, and wipe-dis-
infect them with an approved surface disinfectant.

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.4 Preparation of the dentist unit
NOTICE
Damage caused by spray disinfection.
Disinfectant gets into cracks and loosens the paint.
▶Do not use spray disinfection.
▶Only disinfect by wiping.
Cleaning and disinfection of the foot control
NOTICE
Damage caused by inappropriate use of water.
Damage to the foot control.
▶For cleaning, the foot control must not be immersed in water or placed un-
der running water.
▶When wiping it off with a moist cloth, do not touch the contacts of the
charge socket.
▶Only wipe off. Do not spray.
2.4 Preparation of the dentist unit
2.4.1 Reprocessing of handle and holder pad/anti-slip
mat
Note
The handle of the TM table cannot be detached.
Cleaning and disinfection of the handle TM table / cart
▶Clean the handle with a soft cloth and water, and wipe-disinfect it with an
approved surface disinfectant.
9 / 44

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.4 Preparation of the dentist unit
10 / 44
Cleaning and disinfection of S-table handle and holder
pad/anti-slip mat
▶Press the push button and pull off the handle.
▶Clean the handle under flowing water.
▶Disinfect the white and grey handle by wiping or thermodisinfection (minor
discolouration may occur).
▶Sterilise the holder pad and anti-slip mat by thermodisinfection.

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.4 Preparation of the dentist unit
Sterilisation of S-table handle and holder pad/anti-slip
mat
NOTICE
Damage caused by sterilisation.
▶Do not sterilise the white standard handle.
▶Sterilise the holder pad/ anti-slip mat.
The grey handle (Mat. no. 1.002.4489) can be sterilised (see symbol on the
handle).
2.4.2 Reprocessing of the instrument holder of the TM
table
Note
The handpiece holder (Mat. no. 3.001.4229) can be removed to facilitate
cleaning.
Cleaning and disinfection of the instrument holder
NOTICE
Damage caused by treatment in a washer disinfector.
▶Do not treat the instrument holder in a washer disinfector.
11 / 44

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.4 Preparation of the dentist unit
12 / 44
▶Place the instrument hoses in the corresponding places of the germ reduc-
tion attachment during the cleaning and germ reduction of the instrument
holder.
with patient part assembly kit / without patient part assembly kit
▶Pull the latches evenly outward and carefully remove the handpiece holder.
▶Clean the handpiece holder under running water.
▶Wipe-disinfect the instrument holder.
Sterilize the instrument holder
NOTICE
Damage caused by sterilisation.
▶Do not sterilise the instrument holder.

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.4 Preparation of the dentist unit
2.4.3 Reprocessing of the instrument arm S table
Note
The instrument arm S table (Mat. no. 1.007.4756) can be removed to facil-
itate cleaning.
Cleaning and disinfection of the instrument arm S table
NOTICE
Damage caused by treatment in a washer disinfector.
▶Do not sterilise the instrument arm S table in a washer disinfector.
Note
Neither the rinsing program nor the intensive germ reduction can be carried
out when the instrument arm is removed.
▶Switch off the unit at the main switch.
▶Attach the germ reduction attachment.
with patient part assembly kit / without patient part assembly kit
▶Take the handpieces off the hoses.
13 / 44

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.4 Preparation of the dentist unit
14 / 44
▶Take the roller out of the instrument arm and then place the hose in the
germ reduction attachment.
▶Pull-off the swing-arm in an upward direction.
▶Clean the swing-arm and roller under running water.
▶Wipe the instrument arm S table with disinfectant.
Sterilisation of instrument arm S table
NOTICE
Damage caused by sterilisation.
▶Do not sterilise the instrument arm S table.
2.4.4 Setting up the 3-function and multifunction
handpiece
Note
Wet the O-rings of the gripping sleeves after sterilisation using silicone
grease (Mat. no. 1.000.6403) or KaVo Rota Spray 2 (Mat. no.
0.411.7510). After replacing the cannula, the air channel must be blown out
before the start of treatment to ensure that the air exiting during treatment
is dry.
Cleaning the triple-function and multifunctional
handpiece
Automatic cleaning
Not applicable.
NOTICE
Damage caused by improper cleaning/disinfection.
▶Do not wash the gripping sleeve and the cannula in the washer disinfector.
▶Do not sterilise the gripping sleeve and the cannula in the hot-air steriliser.
▶Do not place the gripping sleeve and the cannula in a disinfectant or ultra-
sonic bath.

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.4 Preparation of the dentist unit
Manual cleaning
Note
Combine manual cleaning with disinfection.
Cleaning the interior
▶Leave the gripping sleeve and cannula on the instrument, and activate the
air and water for 60 seconds.
External cleaning
CAUTION
Danger of injury if the valve body is hot (heating elements, high-pres-
sure lamp).
Risk of burn injury.
▶Switch off the unit at the main switch.
▶Let the handpiece cool after long use.
Accessories required:
▪ Tap water 30oC ± 5oC
▪ Brush, e.g. medium-hard toothbrush
▶Disassemble the gripping sleeve and cannula.
▶Detach the key part from the gripping sleeve.
▶Clean the key part, gripping sleeve and cannula by brushing them under
running water (at least tap water quality).
▶Immediately remove contamination from materials used in the dental prac-
tice (impression materials, caustic chemicals).
▶Carefully wipe off contamination from the cannula tip with a soft Q-tip or
soft cloth and water.
NOTICE
Damage caused by using a nozzle needle that is too long.
Damage to the internal hoses of the cannula.
▶Use a short nozzle needle (Mat. no. 1.004.4986) to clean the media exit
holes.
▶Carefully remove contamination from the media exit ports using the short
nozzle cleaning needle.
15 / 44

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.4 Preparation of the dentist unit
16 / 44
Disinfection of the 3-function and multifunction
handpiece
Manual disinfection
External disinfection
▶Wipe-disinfect the surfaces with a soft cloth.
Automatic disinfection
Not applicable.
NOTICE
Damage caused by improper cleaning/disinfection.
▶Do not wash the gripping sleeve and the cannula in the washer disinfector.
▶Do not sterilise the gripping sleeve and the cannula in the hot-air steriliser.
▶Do not place the gripping sleeve and the cannula in a disinfectant or ultra-
sonic bath.
Drying the 3-function and multifunction handpiece
Manual drying
▶Blow off the outside and inside with compressed air until water drops are no
longer visible.
Automatic drying
Not applicable.
Care of the 3-function and multifunctional handpiece
Requirement
The multifunctional handpiece has been reprocessed.
▶Apply KaVo silicone grease (Mat. no. 1.000.6403) or KaVo Rota Spray 2
(Mat. no. 0.411.7510) to the O-rings of the joint between the gripping
sleeve and cannula. Use cotton buds for this purpose.
Sterilising the 3-function and multifunction handpiece
Note
The grip sleeve and cannula can be sterilised.
▶Hold the 3-way or multifunctional handpiece at the gripping sleeve and take
off the cannula with a slight twisting motion.

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.4 Preparation of the dentist unit
▶Pull the gripping sleeve off the valve body.
Sterilization in a steam sterilizer in compliance with DIN
EN 13060
▶Weld the cannula and grip sleeve in sterile goods packaging.
▶Sterilise with a triple fractionated vacuum (B class steriliser); hold for 4
minutes; 134°C ± 1 °C; overpressure: 2.13 bar.
NOTICE
Damage caused by over-heating.
Damage to the gripping sleeve.
▶Immediately remove the parts from the steriliser after the sterilisation cycle
is completed.
Storage
▶Reprocessed products should be stored protected from dust with minimum
exposure to germs in a dry, dark and cool place.
2.4.5 Preparation of the instrument hoses
Cleaning and disinfection of instrument hoses
▶Clean the hoses and couplings with a cloth and water.
NOTICE
Damage caused by spray disinfection.
▶Do not subject instrument hoses to spray disinfection.
▶Subject instrument hoses to wipe disinfection.
17 / 44

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.4 Preparation of the dentist unit
18 / 44
2.4.6 Servicing the turbine return air filter
Cleaning the turbine return air filter
Note
The liquid collector must be checked weekly.
▶If there is any liquid in the filter, drain the liquid and replace the O-rings of
the multiflex couplings.
▶If necessary, replace the turbine return air filter (Mat. no. 0.200.3098)
and clean the filter holder.
Note
The turbine return air filter is in the same position in the dentist element vari-
ant with S table.
2.4.7 Reprocessing KaVo ERGOcam One
Note
The camera handle cannot be sterilised or disinfected with heat.
Cleaning
Note
Disinfect the camera before cleaning.
Disinfect after cleaning if necessary.
Exterior cleaning by hand
NOTICE
Damage to the camera due to improper cleaning.
Destroys the surface or the optical system of the camera.
▶Do not use abrasives or aggressive cleansers!
▶Do not immerse the camera in liquids!
▶Switch main device switch off.
▶Remove the camera.

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.4 Preparation of the dentist unit
▶Clean the surface with a soft cloth and mild liquid cleaning agent.
Disinfection
Exterior disinfection by hand
WARNING
Highly flammable gases-.
Explosion.
▶Allow product to cool before disinfecting.
NOTICE
Damage to the camera due to improper disinfection.
Irreversible destruction of the camera.
▶Disinfect with wipes only, do not use disinfectant sprays!
▶Do not immerse the camera in liquids!
▶Do not sterilise the camera in an autoclave!
▶Do not store the camera in Steri pack!
▶Do not sterilise the camera with hot air or in a washer disinfector!
▶Switch main device switch off.
▶Allow the camera to cool down.
▶Remove the camera.
▶Disinfect the surface using a soft wipe and disinfectant.
Approved disinfectants:
▪ CaviCide / CaviWipes (Metrex)
19 / 44

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.5 Reprocessing of the assistant unit
20 / 44
▪ Microcide AF Liquid (Schülke & Mayr)
▪ FD 322 (Dürr Dental)
▪ Incidin Liquid (Ecolab)
Note
The exterior of the camera and camera hose can be disinfected with chemical
disinfectants.
Comply with the manufacturer's instructions for use with regard to the applic-
ation range. and exposure time.
NOTICE
Material damage due to use of non-approved disinfectant.
Damage to the camera.
▶Use approved disinfectants only.
2.5 Reprocessing of the assistant unit
2.5.1 Preparing the instrument holder
The instrument holder on the assistant unit is prepared in the same way as the
instrument holder on the dentist unit.
See also:
22.4.2 Reprocessing of the instrument holder of the TM table, Page 11
2.5.2 Preparing the connector for the suction hose
▶Remove connectors ① and ② from the suction hoses.
Cleaning and disinfection of the suction hose connector
▶Clean the disassembled parts under running water.
▶Thermodisinfect the disassembled parts for at least 10 minutes at 93 °C
(total cycle: approximately 20 minutes)
Sterilising the suction hose connector
NOTICE
Damage caused by sterilisation.
▶Do not sterilise the suction hose connector.
Note
Sterilise the suction cannulas according to the manufacturer's instructions.