KBR multimess 1D4 User manual

EDEBDA0193_1112-1_GB
multimess
System I English
User manual
Technical parameters
1D4
Your partner for
network analysis
Energy measuring device

© KBR Kompensationsanlagenbau GmbH
Subject to technical changes
2

V1.00 3
EDEBDA0193_1112-1_GB
KBR multimess 1D4Introduction
Introduction .............................................................................................................. 5
User manual ............................................................................................................... 5
Intended use .............................................................................................................. 5
Explanation of safety relevant symbols ......................................................... 6
Safety notes ................................................................................................................7
Product liability ........................................................................................................ 8
Disposal ...................................................................................................................... 8
Range of functions ..................................................................................................9
multimess 1D4-BS with multimess 1F96-DS ..................................................9
multimess 1D4-BS with multisio 6D6 and
multisio 6F96-DS ....................................................................................................10
multimess 1D4-BS with multisys 3D2-ESBS ..................................................10
Device overview ....................................................................................................11
Installation ................................................................................................................14
Device assembly ....................................................................................................14
Connections .............................................................................................................15
Start-up ......................................................................................................................16
Start-up of the multimess 1D4 with
multimess 1F96-DS display.................................................................................16
Start-up of the multimess 1D4 at the
multisio 6D6 with multisio 6F96-DS ...............................................................19
Start-up of the multimess 1D4 with
multisys 3D2-ESBS .................................................................................................20
System operation ..................................................................................................20
Conguration of system parameters
in the Extras menu ................................................................................................20
Commi function .....................................................................................................22
Para function .......................................................................................................... 22
Consumption monitoring ..................................................................................22
Menu overview ...................................................................................................... 24
Technical data of the measuring module ..................................................... 28
Measuring accuracy ..............................................................................................28
Measuring principle ............................................................................................. 28
Device memory ......................................................................................................29
Power supply ..........................................................................................................29
Hardware inputs and outputs ............................................................................29
Inputs ..........................................................................................................................29
Outputs .................................................................................................................... 29
Electrical connection.............................................................................................30
Mechanical data ......................................................................................................30

KBR multimess 1D4
V1.00
EDEBDA0193_1112-1_GB
4
Standards and miscellaneous ............................................................................31
Technical data of the measuring module ..................................................... 32
Power supply ..........................................................................................................32
Hardware inputs and outputs ............................................................................32
Electrical connection.............................................................................................32
Mechanical data ......................................................................................................32
Standards and miscellaneous ........................................................................... 33
Protective measures ..............................................................................................33
Overvoltage and lightning protection ...........................................................33
Index .......................................................................................................................... 34

V1.00
KBR multimess 1D4
EDEBDA0193_1112-1_GB
5
1 Introduction
Thank you for choosing this KBR quality product. In order to familiarize
yourself with the operation and conguration of the device, we
recommend that you read this manual thoroughly, so that you are
able to make use of the entire range of functions of this high-quality
product.
The individual chapters serve to explain the technical details of
the device and show how to avoid damage by means of proper
installation and commissioning.
1.1 User manual
This user manual describes the multimess 1D4 device version
with multimess 1F96-DS display. For other device versions, e.g.
for multimess 1D4 on multisio 6D6 with multisio 6F96-DS or
multimess 1D4 with multisys 3D2-ESBS, please read the respective
device manual.
This user manual is included in the scope of delivery of the device
and must be accessible for the user at all times (e.g. in the switchgear
cabinet). Even when the device is resold to third parties, the manual
remains part of the device.
Although we used the utmost care in assembling this user manual, we
would like to thank you in advance for notifying us about any errors or
ambiguous descriptions you might notice.
1.2 Intended use
This device is intended for measuring electrical parameters via
external transformers in the low-voltage network (400VAC Ph-Ph).
Introduction

KBR multimess 1D4
V1.00
EDEBDA0193_1112-1_GB
6
1.3 Explanation of safety relevant symbols
This user manual contains notes that must be observed for your
personal safety and to avoid damage to equipment.
These notes are identied by an i or information symbol,
depending on the degree of hazard they represent.
"Warning" means that death, major injuries or damage may occur in
case the appropriate safety measures are not taken.
"Caution" means that minor injuries or damage may occur in case the
appropriate safety measures are not taken.
"Note" is an important information on the product, its operation or the
respective part of the user manual to which special reference is made.
Disclaimer
The content of this user manual has been carefully reviewed in terms
of the hardware and software described. Certain deviations, however,
cannot be excluded, and the manufacturer is not liable for complete
conformity. The specications made in this user manual are checked
on a regular basis, necessary corrections will be included in the next
revision.
Warning
j
Caution
h
Note
i
Introduction

V1.00
KBR multimess 1D4
EDEBDA0193_1112-1_GB
7
Introduction
1.4 Safety notes
 In order to prevent operating errors, operation of this device is
kept as simple as possible. This way, you will be able to quickly start
working with the device.
 In your own interest, however, you should read the following
safety notes carefully. During assembly, the applicable DIN / VDE
regulations must be observed!
 Power supply connection, setup and operation of the device must
be performed by qualied personnel only. Qualied personnel in
accordance with the safety notes in this user manual are persons
authorized to set up, ground and mark devices, systems and circuits
in accordance with the applicable standards and regulations.
 To avoid re and electrical shock, the device must not be exposed to
rain or humidity!
 Before connecting the device to the power supply, check whether
the local power supply conditions comply with the specications on
the nameplate.
 A faulty connection can lead to the destruction of the device!
 When connecting the device, observe the connection chart (see
chapter “Connection chart”) and make sure that no voltage is applied
to the connection lines. Only use proper wiring material and observe
the correct polarity when wiring!
 In order to ensure proper and safe operation of the product, it must
be transported, stored, installed and assembled in accordance with
the specications and operated and maintained carefully.
 A visibly damaged device must generally be considered unt for use
and disconnected from the power supply!
 Error detection, repair and maintenance work may only be carried
out in our facilities or after contacting the service team.
 Unauthorized opening of the device voids any warranty. Correct
operation can no longer be guaranteed!
 Opening the device may expose live parts. Capacitors in the device
may still be loaded, even if the device has been disconnected from
all voltage sources. It is generally not allowed to operate an open
device!

KBR multimess 1D4
V1.00
EDEBDA0193_1112-1_GB
8
Introduction
 In systems susceptible to lightning, lightning protection must be
provided for all input and output lines (for recommendations, see
chapter “Protective measures”)!
1.5 Product liability
You have acquired a high quality product. In its manufacture, only
components of the highest reliability and quality were used. Each
device is subject to long-term testing before it is delivered. Regarding
product liability, we refer to our general terms and conditions for
electronic equipment, which you can nd at www.kbr.de . The
warranted characteristics of the device only apply for operation in
accordance with its intended use!
1.6 Disposal
Defective, outdated or no longer used devices must be properly
disposed of. At your request, we will dispose of the devices for you.

V1.00
KBR multimess 1D4
EDEBDA0193_1112-1_GB
9
Insert battery
2 Range of functions
multimess 1D4 is a multimeter for busbar mounting. On the output
side, it can measure all typical alternating and direct current
parameters of consumers.
The following device expansion stages are possible, featuring dierent
ranges of function:
 “multimess 1D4-BS with multimess 1F96-DS” on page 9
 “multimess 1D4-BS with multisio 6D6
and multisio 6F96-DS” on page 10
 “multimess 1D4-BS with multisys 3D2-ESBS” on page 10
2.1 multimess 1D4-BS with multimess 1F96-DS
Connection of the optional multimess 1F96-DS display can be
established with a ready-made RJ12 cable. For operation of the
display, an additional power supply unit is needed, e. g. the multisys
1D4-PS-24V. This way, no complicated wiring of voltage and current
paths from the converter to the switchgear cabinet door is necessary.
Up to 10 measuring modules can be read out and displayed.
Connection between the modules is also established via ready-made
RJ12 cables.
Power supply of the measuring device is provided by the measuring
voltage. A separate control voltage is not necessary.
multimess 1D4-BS with multimess 1F96-DS is the version described in
this user manual.
Note
i

KBR multimess 1D4
V1.00
EDEBDA0193_1112-1_GB
10
2.2 multimess 1D4-BS with multisio 6D6 and multisio 6F96-DS
If the multimess 1D4 is connected to the multisio 6D6 instead of to
the display, the multisio 6D6 creates a load prole memory (P+ P-/ Q+
Q-) and an eBus interface. Five measuring modules can be connected
to each central storage module Connection between the modules is
established via ready-made RJ12 cables.
2.3 multimess 1D4-BS with multisys 3D2-ESBS
For direct connection of the multimess 1D4 to the KBR eBus, the
multisys 3D2-ESBS gateway is required, which also provides the
supply voltage for the module bus interface via ready-made RJ12
cables. A maximum of 15 measuring modules can be connected
(power consumption of the measuring module interface approx. 0.3
W, power output of the multisys 3D2-ESBS gateway approx. 5 W at 24
VDC). For a larger number of measuring modules, the multisys 1D4-PS-
24V power supply unit is required (power output 24 VDC, 10 W).
3 Device overview
multimess 1D4 measuring module
For busbar assembly (7.5 mm rail)
Connection to measuring voltage Ph-N 230 VAC
Measuring current connection via transformer
x/1A or x/5A
Plug terminal connection 2.5 mm2
RJ12 display connection
RJ12 module bus connection for
supply voltage of the bus interface /
connection of additional measuring modules.
Recording of momentary current
and voltage values.
Continuous energy meter for active and
reactive energy

V1.00
KBR multimess 1D4
EDEBDA0193_1112-1_GB
11
multimess 1F96-DS
Display illumination (Dot Matrix 128x96)
Brightness and contrast adjustable
Display dimming time adjustable
(energy saving function)
Operation via sensor buttons
Mounting depth 40 mm
Door assembly cut-out 92x92 mm
Module bus connection RJ12 for measuring
modules and supply voltage
Display of momentary current and voltage
values
Continuous energy meter for active and
reactive energy
Management of up to 10 measuring modules
Assignment of station names to the measuring
modules
Display language selectable
German ("deut") / English ("engl")

KBR multimess 1D4
V1.00
EDEBDA0193_1112-1_GB
12
3.1 Operating structure
The following overview gives
you an idea of the multimess
1D4 operating structure with the
1F96-DS display. For a detailed
description, please refer to
“Menu overview” on page 24.
U PH-N measuring module 1
Module name
Voltage channel 1
Voltage channel 2
Voltage channel 3
Additional
measuring
modules
U PH-PH measuring module 1
Module name
Voltage channel 1
Voltage channel 2
Voltage channel 3
Additional
measuring
modules
Apparent current meas. module 1
Module name
Apparent current channel 1
Apparent current channel 2
Apparent current channel 3
Additional
measuring
modules
Total power
Module name
Apparent power
Active power
Reactive power
Additional
measuring
modules
Apparent power meas. module 1
Module name
Apparent power channel 1
Apparent power channel 2
Apparent power channel 3
Additional
measuring
modules
Instantaneous value display

V1.00
KBR multimess 1D4
EDEBDA0193_1112-1_GB
13
Active power meas. module 1
Module name
Active power channel 1
Active power channel 2
Active power channel 3
Additional
measuring
modules
Reactive power meas. module 1
Module name
Reactive power channel 1
Reactive power channel 2
Reactive power channel 3
Additional
measuring
modules
Cosine Phi measuring module 1
Module name
Cosine Phi channel 1
Cosine Phi channel 2
Cosine Phi channel 3
Additional
measuring
modules
Frequency
Module name
Network frequency
Additional
measuring
modules
Energy meter:
Continuous counter
active energy
Continuous counter
reactive energy
Additional
measuring
modules
Extras (Settings)
Display rmware version
Commissioning
Conguration
Commissioning
Password
Module name
Scan / remove module
Reset display
Single-phase / 3-phase measurement
Transformer I 1 / 2
Transformer U 1 / 2
Conguration
Display rmware module
Measuring module selection
LCD contrast
LCD brightness
LCD dimmer brightness
Dimmer delay
Display test
Language selection

KBR multimess 1D4
V1.00
EDEBDA0193_1112-1_GB
14
4 Installation
In this chapter, you will nd a description of:
“Device assembly” on page 14
“Connections” on page 15
“Commissioning” on page 16
4.1 Device assembly
During installation, the applicable DIN / VDE regulations must
be observed! Before connecting the device to the power supply,
check whether the local power supply conditions comply with the
specications on the nameplate. A faulty connection may destroy
the system! The device must be connected in accordance with the
connection chart. For energy and synchronous pulse input, polarity
must be observed (contact your energy supplier).
In systems susceptible to lightning, lightning protection must be
provided for the control voltage, bus line and pulse lines (e.g. energy
supplier pulse lines from the transformer station to the location of the
energy control system).

V1.00
KBR multimess 1D4
EDEBDA0193_1112-1_GB
15
4.2 Connections
Terminals 10 - 13
(L1, L2, L3, N)
Measuring voltage. The power supply
of the device is also provided by the
measuring voltage. For technical data,
please refer to the nameplate.
Terminals 20 (k1) and 21 (l1), 22 (k2) and
23(l2), 24 (k3) and 25 (l3)
Measuring inputs for current. The
measuring inputs for current must be
connected via current transformers
x/1A AC or x/5A AC. When connecting
transformers, pay attention to the energy
ow direction and the correct assignment
of measuring voltage inputs to the current
transformers.
Measuring voltage
Messspannung
23
l2
Messstrom
Measuring current
21
l1k1
20
k2
22 25
l3k3
24
L2
N
L3
L1
Stromflussrichtung / current direction
101213 11
L1L3N L2 Modul Modul
Index Änderung Datum Name
Strasser02.05.11
Erstellung
Bezeichnung:
EDV Bezeichnung:
Artikelnr.:
Geprüft Datum
02.05.2011
Anschlussplan
multimess 1D4-BS
DTDASP0042_1811-1_multimess 1D4-BS.ai
Blatt
1 / 1
A4Maßstab: 1 : 1
GmbH
Am Kiefernschlag 7
91126 Schwabach

KBR multimess 1D4
V1.00
EDEBDA0193_1112-1_GB
16
4.3 Start-up
The following section describes the start-up procedure for the
dierent device versions.
4.3.1 Start-up of the multimess 1D4 with multimess 1F96-DS display
For starting up the multimess 1D4 with multimess 1F96-DS display,
please proceed as follows:
1. Connect the measuring module to the multimess 1F96-DS display
via the module bus interface.
2. With the "Module out" connector, connect the measuring module to
the multisys 1D4-PS-24V power supply unit via the second module
bus interface.
3. At the multisys 1D4 power supply unit, connect the supply voltage
(refer to nameplate). The operation LED on the device is illuminated
green.
4. At the terminals 10 (L1), 11 (L2), 12 (L3) and 13 (N), connect the
measuring voltage (the operating voltage of the measuring
module).
5. At the display, select the menu Extras > Commissioning to scan
measuring modules connected.
6. Displayed are modules already existing, as well as the menu items
"scan" and "rem." (for removing measuring modules from the
module bus list).
7. After selection of the menu item "scan", the scan mode is activated
and the function LED at the measuring modules ashes slowly.

V1.00
KBR multimess 1D4
EDEBDA0193_1112-1_GB
17
8. At the measuring module, the scan sensor button (close to the
status LED, ashing green) is unlocked.
9. To set the measuring module into scan mode, touch the scan
sensor button for about 4 seconds (the green status LED ashes
more quickly)
10. The multimess display recognizes the measuring module and adds
it to the list of modules connected.
11. You can now scan further modules, which are automatically
added to the module list or, by touching the stop button, end the
scanning process. The display can manage a maximum number of
ten modules.
Set-up diagram for operation of the
multimess 1D4 with multimess 1D4-DS (example):
LCD Measuring module 1
to 10 (maximum)
multisys
1D4-PS-24V
power supply
unit
101 102 PE
+_N PE
multisys 1D4-PS24V
24V DC 85 - 260V AC
Netz / Power
Modul
out
Modul
in
1 2
L

KBR multimess 1D4
V1.00
EDEBDA0193_1112-1_GB
18
Conguration
Extras menu
Display of the rmware version
and release of the display
DS display
01.00 version
005 release
Previous menu
Display of measuring module version,
Display conguration
Start commissioning
Next menu
Display of the rmware version
and release of the measuring
module at the module bus
Measuring module designation
BS type module bus device
01.00 version
001 release
Selection of next measuring module
Selection of previous measuring module
Next menu

V1.00
KBR multimess 1D4
EDEBDA0193_1112-1_GB
19
4.3.2 Start-up of the multimess 1D4
at the multisio 6D6 with multisio 6F96-DS
For starting up the multimess 1D4 at the multisio 6D6, please proceed
as follows:
1. Connect the measuring module to the multisio 6D6 via the module
bus interface.
2. At the terminals 10 (L1), 11 (L2), 12 (L3) and 13 (N), connect the
measuring voltage (the operating voltage of the measuring
module).
3. On the display, select the menu Settings > Module management.
4. Displayed are the multisio basic module as well as modules already
existing and the menu item "scan".
5. After selecting this menu item with the cursor buttons, the scan
mode can be started with the scan button and the scan display
begins to ash. This way, the scan button at the measuring module
(close to the status LED, ashing green) is unlocked.
6. By pressing the scan sensor button for approx. 4 seconds, set the
measuring module into scan mode (the green status LED ashes
more quickly).
The multisio basic module now recognizes the measuring module and
adds it to the list of modules connected.
You can now scan further modules, which are automatically added
to the module list or, by touching the stop button, end the scanning
process. The multisio 6D6 can manage a maximum number of ten
modules.
You can now read out and process the data.

KBR multimess 1D4
V1.00
EDEBDA0193_1112-1_GB
20
4.3.3 Start-up of the multimess 1D4 with multisys 3D2-ESBS
For starting up the multimess 1D4 at the KBR eBus via the multisys
3D2-ESBS gateway, please proceed as follows:
1. Connect the measuring module to the multisys 3D2 gateway via the
module bus interface.
2. At the terminals 10 (L1), 11 (L2), 12 (L3) and 13 (N), connect the
measuring voltage (the operating voltage of the measuring module).
3. Connect the multisys 3D2 gateway to the KBR eBus using terminals
90, 91 and 92.
A command, triggered by the visual energy computer software,
unlocks the scan button at the measuring module (close to the
status LED, ashing green).
4. By pressing the scan sensor button for approx. 4 seconds, set the
measuring module into scan mode (the green status LED ashes
more quickly).
The measuring module is detected and included in the bus list.
You can now read out and process the data.
5 System operation
In this chapter, you will nd instructions on how to operate the
multimess 1D4 with the multisio 1D4-DS display in daily use.
Furthermore, it contains references to the complete range of
functions.
5.1 Conguration of system parameters in the Extras menu
To adapt multimess 1D4 to the system monitored, its parameters have
to be congured.
 Press the F1 key eleven times, selecting the Extras menu.
Here, measuring modules connected and the rmware version of the
display are shown.
You have access to the following functions:
 “Commi function” on page 22
 “Para function” on page 22
The menu navigation of the multimess 1D4-DS is self-explanatory.
The operator is guided and supported by the device through
operating instructions displayed for the respective situation.