KEBCO COMBILINE Z2 Series User manual

COMBILINE Z2
INSTRUCTIONS FOR USE | INSTALLATION Z2 OUTPUT FILTER
Translation of the original manual
Document 20184032 EN 03

3
PREFACE
Preface
The described hard- and software are developments of the KEB Automation KG. The
enclosed documents correspond to conditions valid at printing. Misprint, mistakes and
technical changes reserved.
Signal words and symbols
Certain operations can cause hazards during the installation, operation or thereafter.
There are safety informations in the documentation in front of these operations. Security
signs are located on the device or machine. A warning contains signal words which are
explained in the following table:
DANGER Dangerous situation, which will cause death or serious injury in case of
non-observance of this safety instruction.
WARNING Dangerous situation, which may cause death or serious injury in case of
non-observance of this safety instruction.
CAUTION Dangerous situation, which may cause minor injury in case of non-ob-
servance of this safety instruction.
NOTICE Situation, which can cause damage to property in case of non-obser-
vance.
RESTRICTION
Is used when certain conditions must meet the validity of statements or the result is
limited to a certain validity range.
Is used when the result will be better, more economic or trouble-free by follow-
ing these procedures.
More symbols
► Thisarrowstartsanactionstep.
• / - Enumerations are marked with dots or indents.
=> Cross reference to another chapter or another page.
Note to further documentation.
www.keb.de/service/downloads

4
PREFACE
Laws and guidelines
KEBAutomationKGconrmswiththeECdeclarationofconformityandtheCEmarkon
the device nameplate that it complies with the essential safety requirements.
The EC declaration of conformity can be downloaded on demand via our website. Fur-
therinformationisprovidedinchapter"Certication".
Warranty and liability
The warranty and liability on design, material or workmanship for the acquired device is
given in the general sales conditions.
Hereyouwillndourgeneralsalesconditions.
www.keb.de/terms-and-conditions
Furtheragreementsorspecicationsrequireawrittenconrmation.
Support
Through multiple applications not every imaginable case has been taken into ac-
count. If you require further information or if problems occur which are not treated de-
tailed in the documentation, you can request the necessary information via the local
KEB Automation KG agency.
The use of our units in the target products is outside of our control and therefore
lies exclusively in the area of responsibility of the customer.
Theinformationcontainedinthetechnicaldocumentation,aswellasanyuser-specic
advice in spoken and written and through tests, are made to best of our knowledge and
information about the intended use. However, they are regarded as being only informal
and changes are expressly reserved, in particular due to technical changes. This also
applies to any violation of industrial property rights of a third-party. Selection of our units
in view of their suitability for the intended use must be done generally by the user.
Tests can only be done within the intended end use of the product (application) by
the customer. They must be repeated, even if only parts of hardware, software or
the unit adjustment are modied.
Copyright
The customer may use the instructions for use as well as further documents or parts
from it for internal purposes. Copyrights are with KEB Automation KG and remain valid
in its entirety.
This KEB product or parts thereof may contain third-party software, including free and/
or open source software. If applicable, the license terms of this software are contained
in the instructions for use. The instructions for use are already available to you, can be
downloaded free of charge from the KEB website or can be requested from the respec-
tive KEB contact person.
Other wordmarks or/and logos are trademarks (™) or registered trademarks (®) of their
respective owners.

5
TABLE OF CONTENTS
Table of Contents
Preface ....................................................................................................................................................3
Signal words and symbols .............................................................................................................3
More symbols.................................................................................................................................3
Laws and guidelines.......................................................................................................................4
Warranty and liability......................................................................................................................4
Support ........................................................................................................................................4
Copyright........................................................................................................................................4
Table of Contents ...................................................................................................................................5
List of Figures.........................................................................................................................................7
List of Tables ..........................................................................................................................................8
Standards for EMC components...........................................................................................................9
Product standards:.........................................................................................................................9
Basic standards:.............................................................................................................................9
General standards:.........................................................................................................................9
1 Basic Safety Instructions............................................ 10
1.1 Target group................................................................................................................................... 10
1.2 Transport, storage and proper use.............................................................................................. 10
1.3 Installation...................................................................................................................................... 11
1.4 Electrical connection ....................................................................................................................12
1.5 Start-up and operation ..................................................................................................................12
1.6 Repair .............................................................................................................................................13
1.7 Disposal..........................................................................................................................................13
2 Product Description .................................................... 14
2.1 Specied application.....................................................................................................................14
2.2 Unintended use.............................................................................................................................. 14
2.3 Product features ............................................................................................................................15
3 Technical Data.............................................................. 16
3.1 Operating conditions ....................................................................................................................16
3.1.1 Climatic environmental conditions......................................................................................16
3.1.2 Mechanical environmental conditions ................................................................................17
3.1.3 Chemical/mechanical active substances............................................................................17
3.1.4 Electrical operating conditions............................................................................................17
3.1.4.1 Deviceclassication........................................................................................................17
3.2 Device data..................................................................................................................................... 18
3.2.1 Mechanical data of the motor chokes.................................................................................18
3.2.2 Electrical data of the motor chokes ....................................................................................19
3.2.3 Mechanical data of the capacitor modules.........................................................................20
3.2.4 Electrical data of the capacitor modules.............................................................................21
3.2.5 Technical data of the cable sets .........................................................................................22
3.2.6 Possiblecombinationofoutputlters.................................................................................23

6
TABLE OF CONTENTS
3.3 Dimensions and weights ..............................................................................................................25
3.3.1 Motor chokes size 07 to 12 ................................................................................................25
3.3.2 Motor chokes size 13 to 19 ................................................................................................26
3.3.3 Motor chokes size 20 to 22 ................................................................................................27
3.3.4 Motor chokes size 23 to 30 ................................................................................................28
3.3.5 Capacitor modules in housing............................................................................................29
3.3.6 Capacitor module with a power capacitor ..........................................................................30
3.3.7 Capacitor module with two power capacitors.....................................................................31
3.3.8 Capacitor module with three power capacitors ..................................................................32
3.3.9 Capacitor module with four power capacitors ....................................................................33
4 Installation and Connection........................................ 34
4.1 Schematic diagram with motor choke.........................................................................................34
4.2 Schematic diagram with output lter .......................................................................................... 35
4.3 Overtemperature shutdown.......................................................................................................... 36
4.3.1 Rated data NC contact temperature monitoring.................................................................36
4.4 Connection of the motor chokes .................................................................................................37
4.4.1 Connection of the motor chokes size 07 to 12 ...................................................................37
4.4.2 Connection of the motor chokes size 13 to 19 ...................................................................38
4.4.3 Connection of the motor chokes size 20 to 22 ...................................................................39
4.4.4 Connection of the motor chokes size 23 to 30 ...................................................................40
4.5 Connection of the capacitor modules .........................................................................................41
4.5.1 Connecting example for capacitor modules with M12 screw connection...........................41
4.5.2 Connection of the capacitor module in the housing ...........................................................41
4.5.3 Connection of the capacitor module with a power capacitor..............................................42
4.5.4 Connection of the capacitor module with two power capacitors.........................................42
4.5.5 Connection of the capacitor module with three power capacitors......................................43
4.5.6 Connection of the capacitor module with four power capacitors........................................44
4.6 Transport of the motor chokes from size 23...............................................................................45
4.7 Control cabinet installation .......................................................................................................... 46
4.7.1 Installation position of the motor chokes ............................................................................46
4.7.2 Installation position of the capacitor modules.....................................................................46
4.7.3 Ventilation of the motor chokes from size 25......................................................................47
4.7.4 Installation clearances for wall mounting for capacitors 00Z2G24-00x5, 00Z2G24-
00x6, 00Z2G24-00x7 and motor chokes 07...12Z2F04-1003.......................................48
4.7.5 Installationclearancesforoormountingforcapacitors00Z2G24-00x1,00Z2G24-00x2,
00Z2G24-00x3, 00Z2G24-00x4 and motor chokes 13...30Z2F04-1003.......................... 48
5 Certication.................................................................. 49
5.1 CE-Marking.....................................................................................................................................49
5.2 UL certication ..............................................................................................................................49
6 Revision History .......................................................... 51

7
LIST OF FIGURES
List of Figures
Figure 1: Dimensions and weights motor chokes size 07 to 12......................................................25
Figure 2: Dimensions and weights motor chokes size 13 to 19......................................................26
Figure 3: Dimensions and weights motor chokes size 20 to 22......................................................27
Figure 4: Dimensions and weights motor chokes size 23 to 30......................................................28
Figure 5: Dimensions and weight of capacitor modules in housing ................................................29
Figure 6: Dimensions and weight capacitor module with a power capacitor ..................................30
Figure 7: Dimensions and weight capacitor module with two power capacitors .............................31
Figure 8: Dimensions and weight capacitor module with three power capacitors ..........................32
Figure 9: Dimensions and weight capacitor module with four power capacitors ............................33
Figure 10: Schematic diagram with motor choke..............................................................................34
Figure11: Schematicdiagramwithoutputlter................................................................................35
Figure 12: Connection of the motor chokes size 07 to 12.................................................................37
Figure 13: Connection of the motor chokes size 13 to 19.................................................................38
Figure 14: Connection of the motor chokes size 20 to 22.................................................................39
Figure 15: Connection of the motor chokes size 23 to 30.................................................................40
Figure 16: Connecting example for capacitor modules with M12 screw connection ........................41
Figure 17: Connection of the capacitor module in the housing.........................................................41
Figure 18: Connection of the capacitor module with a power capacitor ...........................................42
Figure 19: Connection of the capacitor module with two power capacitors ......................................42
Figure 20: Connection of the capacitor module with three power capacitors ...................................43
Figure 21: Connection of the capacitor module with four power capacitors .....................................44
Figure 22: Transport of a motor choke..............................................................................................45
Figure 23: Ventilation of the motor chokes from size 25...................................................................47
Figure 24: Installation clearances for wall mounting .........................................................................48
Figure25: Installationclearancesforoormounting ........................................................................48

8
LIST OF TABLES
List of Tables
Table 1: Climatic environmental conditions ...................................................................................16
Table 2: Mechanical environmental conditions..............................................................................17
Table 3: Chemical/mechanical active substances .........................................................................17
Table4: Deviceclassication.........................................................................................................17
Table 5: Mechanical data of the motor chokes ..............................................................................18
Table 6: Electrical data of the motor chokes..................................................................................19
Table 7: Mechanical data of the capacitor modules.......................................................................20
Table 8: Electrical data of the capacitor modules ..........................................................................21
Table 9: Technical data of the cable sets.......................................................................................22
Table10: Possiblecombinationofoutputlters ..............................................................................24
Table 11: Rated data NC contact.....................................................................................................36

9
STANDARDS FOR EMC COMPONENTS
Standards for EMC components
Product standards:
EN61558-1 Safety of transformers, reactors, power supply units and combinations thereof -
Part 1: General requirements and tests (IEC 96/449/CD:2015)
EN 61558-2-20 Safety of transformers, reactors, power supply units and combinations thereof
- Part 2-20: Particular requirements and tests for small reactors (IEC 61558-2-
20:2010); German version EN 61558-2-20:2011
EN61800-5-1 Adjustable speed electrical power drive systems - Part 5-1: Safety requirements
- Electrical, thermal and energy (IEC 61800-5-1); German version EN 61800-5-1
UL61800-5-1 American version of the EN 61800-5-1 with „National Deviations“
Basic standards:
EN60529 Degrees of protection provided by enclosures (IP Code) (IEC 60529)
EN60664-1 Insulation coordination for equipment within low-voltage systems Part 1: Princi-
ples, requirements and tests (IEC 60664-1)
EN60721-3-1 Classicationofenvironmentalconditions-Part3-1:Classicationofgroupsof
environmental parameters and their severities - Section 1: Storage (IEC 60721-
3-1); German version EN 60721-3-1
EN60721-3-2 Classicationofenvironmentalconditions-Part3:Classicationofgroupsof
environmental parameters and their severities - Section 2: Transportation and
handling (IEC 104/670/CD)
EN60721-3-3 Classicationofenvironmentalconditions-Part3:Classicationofgroupsof
environmental parameters and their severities; section 3: Stationary use at
weatherprotected locations; Amendment A2 (IEC 60721-3-3); German version
EN 60721-3-3
General standards:
DGUV regulation 3 Electrical installations and equipment
DNVGL-CG-0339 Environmentaltestspecicationforelectrical,electronicandprogrammable
equipment and systems
DINIEC60364-5-54 Low-voltage electrical installations - Part 5-54: Selection and erection of
electrical equipment - Earthing arrangements, protective conductors and protec-
tive bonding conductors (IEC 64/1610/CD)
EN60204-1 Safety of machinery - electrical equipment of machines Part 1: General require-
ments (VDE0113-1, IEC44/709/CDV)
EN61373 Railway applications - Rolling stock equipment - Shock and vibration tests (IEC
61373); German version EN 61373
ISO 4762 Hexagon socket head cap screws

10
BASIC SAFETY INSTRUCTIONS
1.2 Transport, storage and proper use
Thetransport iscarried outby qualiedpersons in accordancewith theenvironmen-
talconditionsspeciedinthismanual.Thefiltersshallbeprotectedagainstexcessive
strains.
Donotstorethelters
• in the environment of aggressive and/or conductive liquids or gases.
• with direct sunlight.
• outsidethespeciedenvironmentalconditions.
1 Basic Safety Instructions
The COMBIVERT is designed and constructed in accordance with state-of-the-art tech-
nology and the recognised safety rules and regulations However, the use of such de-
vices may cause functional hazards for life and limb of the user or third parties, or dama-
ges to the system and other material property.
The following safety instructions have been created by the manufacturer for the area of
electric drive technology. They can be supplemented by local, country- or application-
specic safety instructions. This list is not exhaustive. Non-observance of the safety
instructions by the customer, user or other third party leads to the loss of all resulting
claims against the manufacturer.
NOTICE Hazards and risks through ignorance.
►Read the instructions for use !
►Observe the safety and warning instructions !
►If anything is unclear, please contact KEB Automation KG !
1.1 Target group
This instruction manual is determined exclusively for electrical personnel. Electrical per-
sonnelforthepurposeofthisinstructionmanualmusthavethefollowingqualications:
• Knowledge and understanding of the safety instructions.
• Skills for installation and assembly.
• Start-up and operation of the product.
• Understanding of the function in the used machine.
• Detection of hazards and risks of the electrical drive technology.
• Knowledge of DIN IEC 60364-5-54.
• Knowledge of national safety regulations.

11
BASIC SAFETY INSTRUCTIONS
CAUTION Maximum design edges and high weight!
Contusions and bruises!
►Never stand under suspended loads.
►Wear safety shoes.
►Secure drive converter accordingly when using lifting gear.
• To prevent damages to the device:
• Make sure that no components are bent and/or isolation distances are changed.
• The device must not be put into operation in case of mechanical defects. Non-
compliance with the applicable standards.
• Do not allow moisture or mist to penetrate the unit.
• Avoiddustpermeatingthedevice.Allowforsu󰀩cientheatdissipationifinstalledin
a dust-proof housing.
• Note installation position and minimum distances to surrounding elements. Do not
cover the ventilation openings.
• Mountthedriveinverteraccordingtothespecieddegreeofprotection.
• Make sure that no small parts fall into the COMBIVERT during assembly and wiring
(drilling chips, screws etc.). This also applies to mechanical components, which can
lose small parts during operation.
• Checkthereliabletofthedeviceconnectionsinordertoavoidcontactresistances
and sparking.
• Do not walk-on drive converter.
• The safety instructions are to be kept!
1.3 Installation
DANGER Do not operate in an explosive environment!
EX
►The COMBIVERT is not intended for the use in potentially explosive
environment.

12
BASIC SAFETY INSTRUCTIONS
1.4 Electrical connection
DANGER Voltage at the terminals and in the device!
Danger to life due to electric shock!
► Foranyworkontheunitswitcho󰀨thesupplyvoltageandsecureit
against switching on.
►The supplied drive converters and filters form a technical unit and
must therefore not be disconnected from the mains independently of
one another.
►Wait until the drive has stopped in order that no regenerative energy
can be generated.
►Observe capacitor discharge time, if necessary measure DC voltage
at the terminals.
►Never bridge upstream protective devices (also not for test purpos-
es).
For a trouble-free and safe operation, please pay attention to the following instructions:
• The electrical installation shall be carried out in accordance with the relevant re-
quirements.
• Cable cross-sections and fuses must be dimensioned according to the design of
themachinemanufacturer.Speciedminimum/maximumvaluesmaynotbefallen
below /exceeded.
• With existing or newly wired circuits the person installing the units or machines must
ensure the EN requirements are met.
1.5 Start-up and operation
CAUTION High temperatures at heat sink and coolant !
Burning of the skin!
►Cover hot surfaces safe-to-touch.
►If necessary, attach warning signs on the system.
►Check surface and coolant lines before touching them.
►Before working let the unit cool down.
• During operation, all covers and control cabinet doors shall be kept closed.
• Only use accessories approved for the device.
• Never touch terminals, busbars or cable ends.

13
BASIC SAFETY INSTRUCTIONS
1.6 Repair
In case of malfunction, unusual noises or smells inform a person in charge!
DANGER Unauthorized exchange, repair and modications!
Unpredictable malfunctions!
► Modicationorrepairispermittedonlybyauthorizedpersonnelby
KEB Automation KG.
►Only use original manufacturer parts.
►Infringement will annul the liability for resulting consequences.
In case of failure, please contact the machine manufacturer. Only the machine manu-
facturer knows the components and can provide appropriate sqare parts or induce the
maintenance.
1.7 Disposal
Electronic devices of the KEB Automation KG are exclusively professional devices for
further industrial processing (so-called B2B devices).
Manufacturers of B2B devices are obliged to take back and recycle devices manufac-
tured after 14.08.2018. These devices may not be disposed at the collection centres of
public sector disposal organisations.
If no deviating agreement has been made between the customer and
KEB or no deviating mandatory legal regulation exists, KEB products
marked in this way can be returned. Company and keyword to the return
point can be taken from the list below. Shipping costs are paid by the
customer. Thereupon the devices will be professionally recycled and
disposed.
Theentrynumbersarelistedcountry-specicinthefollowingtable.Thecorresponding
KEB return addresses can be found on our website.
Withdrawal by WEEE-Reg.-No. Keyword
Austria
KEB Automation GmbH ERA: 51976 Stichwort „Rücknahme WEEE“
France
RÉCYLUM - Recycle point ADEME: FR021806 Mots clés „KEB DEEE“
Germany
KEB Automation KG EAR: DE12653519 Stichwort „Rücknahme WEEE“
Italy
COBAT AEE: (IT) 19030000011216 Parola chiave „Ritiro RAEE“
The packaging must be feed to paper and cardboard recycling.

14
PRODUCT DESCRIPTION
2 Product Description
ThisinstructionsforusedescribetheoutputltersoftheCOMBILINEZ2series.These
are consisting of a motor choke, a capacitor module and an appropriate cable set.
Component Material number
Z2 motor choke xxZ2F04-1003
Z2 capacitor module 00Z2G24-xxxx
Z2 cable set 00Z2T09-xxxx
The use of the motor choke is also possible on its own. It reduces the ripple of the motor
current and the dv/dt to protect the motor insulation.
Ifthecapacitorunitisconnecteddownstream,asine-wavelterisobtained.Thesine-
wavelteractsasalow-passlterfortheswitchingfrequencycomponentsofthedrive
converter output voltage and provides a sinusoidal voltage between the phases.
The components can be combined with each other in such a way that there is an optimal
solution for every application!
2.1 Specied application
Theoutputltersareintendedfortheinstallationintoelectricalsystemsormachines.
Technical data and information for connection conditions shall be taken from the name-
plate and from the instructions for use and must be strictly observed.
2.2 Unintended use
The operation of our products outside the indicated limit values of the technical data
leads to the loss of any liability claims.

15
PRODUCT DESCRIPTION
2.3 Product features
ThisinstructionsforusedescribethecomponentsoftheZ2outputlters:
Device type: Outputlter
Series: COMBILINE Z2
Application range: 0...1600 Hz
TheCOMBILINEZ2outputltersarecharacterizedbythefollowingfeatures:
When using a motor choke
Reduction of the:
• rate of voltage rise (dv/dt)
• motor bearing currents
• motor losses
• motor noises
Whenusinganoutputlter
Sinusoidal output voltage, resulting in a reduction of:
• motor losses
• motor warming
• motor noises
• bearing currents
• EMC emitted interference
The structure itself is determined by:
• Low-loss winding strands as conductor material
• Core material specially designed for this frequency range
• Special capacitors for operation up to 800 / 1600 Hz
Thesefeaturesleadtoasignicantextensionofthemotorlifetime.

3 Technical Data
3.1 Operating conditions
3.1.1 Climatic environmental conditions
Storage Standard Class Notes
Ambient temperature EN 60721-3-1 1K4 -25…55°C
Relative humidity EN 60721-3-1 1K3 5…95% (without condensation)
Storage height – – max. 3000m above sea level
Transport Standard Class Notes
Ambient temperature EN 60721-3-2 2K3 -25…70°C
Relative humidity EN 60721-3-2 2K3 95% at 40°C (without condensation)
Operation Standard Class Notes
Ambient temperature EN 60721-3-3 3K3 5…40°C (extended to -10…45°C)
Coolant inlet tem-
perature Air – – 5…40°C (-10…45°C)
Relative humidity EN 60721-3-3 3K3 5…85% (without condensation)
Version and degree of protec-
tion EN 60529 IP20 Size 07...19
IP00 From size 20
Site altitude – –
Max. 2000m above sea level
• With site altitudes over 1000m a derating
of 1% per 100m must be taken into con-
sideration.
Table 1: Climatic environmental conditions
16
OPERATING CONDITIONS

3.1.2 Mechanical environmental conditions
Storage Standard Class Notes
Vibration limits EN 60721-3-1 1M2 Vibration amplitude 1.5mm (2…9 Hz)
Acceleration amplitude 5m/s² (9…200Hz)
Shock limit values EN 60721-3-1 1M2 40m/s²; 22 ms
Transport Standard Class Notes
Vibration limits EN 60721-3-3 2M1
Vibration amplitude 3.5mm (2…9Hz)
Acceleration amplitude 10m/s² (9…200Hz)
(Acceleration amplitude 15m/s² (200…500Hz)) 1)
Shock limit values EN 60721-3-2 2M1 100m/s²; 11 ms
Operation Standard Class Notes
Vibration limits EN 60721-3-3 3M4 Vibration amplitude 0.3mm (2…9 Hz)
Acceleration amplitude 10m/s² (9…200Hz)
Shock limit values EN 60721-3-3 3M4 100m/s²; 11 ms
Table 2: Mechanical environmental conditions
1) Not tested.
3.1.3 Chemical/mechanical active substances
Storage Standard Class Notes
Contamination Gases EN 60721-3-1 1C2 –
Solids 1S2 –
Transport Standard Class Notes
Contamination Gases EN 60721-3-2 2C2 –
Solids 2S2 –
Operation Standard Class Notes
Contamination Gases EN 60721-3-3 3C2 –
Solids 3S2 –
Table 3: Chemical/mechanical active substances
3.1.4 Electrical operating conditions
3.1.4.1 Deviceclassication
Requirement Standard Class Notes
Pollution degree EN 60664-1 2Non-conductive pollution, occasional condensa-
tion when PDS is out of service.
Table 4: Device classication
17
OPERATING CONDITIONS

18
DEVICE DATA
3.2 Device data
3.2.1 Mechanical data of the motor chokes
Material
number
Connection Typ.
conductor
cross-
section in
mm² /AWG
Tightening torque
in Nm / lb inch With
temperature
switch
Type U, V, W PE U, V, W PE
07Z2F04-1003
Terminal
Push-Lock 6 / 10 — —
—
09Z2F04-1003 —
10Z2F04-1003 —
12Z2F04-1003 —
13Z2F04-1003
RK 6-10/35 M6 10 / 8 2 / 17.7 4.5 / 39.8
—
14Z2F04-1003 —
15Z2F04-1003 —
16Z2F04-1003 —
17Z2F04-1003 RK 16/35
M8
16 / 6 4 / 35.4
10 / 88.5
—
18Z2F04-1003 —
19Z2F04-1003 RK 35/35 35 / 2 5 / 44.3 —
20Z2F04-1003
Bolt
M10
25 / 4
20 / 177
—
21Z2F04-1003 35 / 2 —
22Z2F04-1003 —
23Z2F04-1003
M10
50 / 1
20 / 177
—
24Z2F04-1003 70 / 2/0 —
25Z2F04-1003 ✓
26Z2F04-1003
M12
95 / 3/0
40 / 354
✓
27Z2F04-1003 ✓
28Z2F04-1003 120 / 4/0 ✓
29Z2F04-1003 150 / 250 ✓
30Z2F04-1003 240 / 450 ✓
All data are rated values
Table 5: Mechanical data of the motor chokes
NOTICE Overheating of the motor choke !
►Motor chokes from size 25 must be ventilated!
Further information
=> „Ventilation of the motor chokes from size 25“.

19
DEVICE DATA
3.2.2 Electrical data of the motor chokes
Material
number
Current
in A
Inductance
in mH 1)
Resistance
in mΩ1)
Frequency
in Hz
Typically
power loss
Frequency
range
in Hz
at 600Hz
in W
at 800Hz
in W
at 1600Hz
in W
07Z2F04-1003 2.6 3.5 407 800
—
18 26.5
0...1600
09Z2F04-1003 4.1 2.2 198 800 32 44
10Z2F04-1003 5.8 1.5 172 800 48 74
12Z2F04-1003 9.5 0.967 104 800 99 136
13Z2F04-1003 12 0.766 52 800 35 46
14Z2F04-1003 16.5 0.557 31 800 44 61
15Z2F04-1003 24 0.383 22 800 66 92
16Z2F04-1003 33 0.278 16 800 102 135
17Z2F04-1003 42 0.219 9.52 800 115 148
18Z2F04-1003 50 0.184 6 800 92 109
19Z2F04-1003 60 0.153 6 800 124 152
20Z2F04-1003 75 0.123 6.1 800 152 180
21Z2F04-1003 90 0.102 3.6 800 147 177
22Z2F04-1003 115 0.08 3.7 800 224 264
23Z2F04-1003 150 0,082 2.4 600 264
—
340
24Z2F04-1003 180 0.068 2.4 600 390 530
25Z2F04-1003 210 0,058 1.5 600 430 572
26Z2F04-1003 250 0.049 1 600 492 732
27Z2F04-1003 300 0.041 1 600 515 852
28Z2F04-1003 370 0.033 0.58 600 515 935
29Z2F04-1003 460 0.027 0.48 600 777 1079
30Z2F04-1003 570 0.021 0.39 600 963 1122
Table 6: Electrical data of the motor chokes
1) Limit deviation ±10%.
• Rated voltage corresponds to UN= 400 / 480V.
• All data are rated values except minimum and maximum values.
• The output frequency is to be limited in such a way that it does not exceed 1/10 of the switching
frequency.

20
DEVICE DATA
3.2.3 Mechanical data of the capacitor modules
Material number Connection Tightening torque in Nm / lb inch
L1, L2 (N), L3 PE L1, L2 (N), L3 PE
00Z2G24-0005
Push-Lock
Terminal
3 x 10mm²
Crimp connector
M4 — 2.5 / 21.1
00Z2G24-0015
00Z2G24-0025
00Z2G24-0035
00Z2G24-0045
00Z2G24-0055
00Z2G24-0065
00Z2G24-0006
00Z2G24-0016
00Z2G24-0007
00Z2G24-0017
00Z2G24-0027
00Z2G24-0037
00Z2G24-0047
00Z2G24-0057
00Z2G24-0051
3 x M12 bolt Crimp connector
M6 10 / 88.5 8 / 70.8
00Z2G24-0061
00Z2G24-0001
00Z2G24-0011
00Z2G24-0021
00Z2G24-0031
00Z2G24-0002
3 x FlatAL 80x2mm
drilling: ⌀= 13mm
Crimp connector
M6 25 / 221 8 / 70.8
00Z2G24-0012
00Z2G24-0022
00Z2G24-0032
00Z2G24-0041
00Z2G24-0003
00Z2G24-0042
00Z2G24-0052
00Z2G24-0053
00Z2G24-0013
00Z2G24-0004
00Z2G24-0062
00Z2G24-0023
00Z2G24-0033
00Z2G24-0043
00Z2G24-0014
Table 7: Mechanical data of the capacitor modules
All data are rated values except minimum and maximum values.