Ken A Vision Comprehensive Scope 2 User manual

Digital C mprehensive Sc pe 2
Instruction anual
T-19541C
T-19641C

Table f C ntents
Introduction 2
Packing Contents 2
icroscope Set-up Guide 3
Specifications 5
Troubleshooting 6

Warranty SheetInstruction
anual
icroscope
Cover
Digital Comprehensive Scope 2
icroscope
Power Supply Allen Wrench
Slide icrometer
2
AV 4 Software
Instruction
anual
CameraSoftware
APPLIEDVISION 4.0
Applied VisionT
4 Software
USB Cable
Intr ducti n
Thank you for purchasing the Digital Comprehensive Scope 2. This
digital compound microscope series is specifically designed with
advanced features of a 3.2 megapixel digital camera, a mechanical
stage with spring-loaded stage clips, an Abbe condenser with iris
diaphragm, an adjustable light dimmer (rheostat), and high-quality
objective lenses that will magnify 40-1000 times. Combined with
Ken-A-Vision’s Applied Vision™ software, this microscope is a powerful
product allowing the user to take digital pictures, annotate images, make
measurements, and record full-length or time-lapse videos that add to
the classroom and educational experience.
Packing C ntents

Micr sc pe Set-up Guide
The Digital Comprehensive Scope 2 compound microscope can be set
up in a matter of minutes. To get the most out of this amazing tool,
follow these step-by-step instructions:
1. After unpacking the box, take the Applied Vision™
software CD and insert it into your computer to install.
NOTE: For a complete instruction manual of Applied Vision software,
refer to the .pdf version on the Applied Vision CD.
2. Follow the directions to install the software. Once
completed, an Applied Vision icon should appear on
your computer’s desktop.
3. Remove the Applied Vision CD from your computer
and restart the computer.
4. Remove the Digital Comprehensive Scope 2 from the
plastic bag and remove the protective coverings from
the objective lenses and the eyepiece(s).
5. Place the microscope on a flat, firm surface next to the
computer with the installed Applied Vision software.
6. Check the coarse focus knob on either side of the main
body support. The coarse focus knobs should turn
easily.
NOTE: The stage should move freely up and down the main body
support when focusing. When you release the knob, the stage should
remain stationary, and not slide down the post on its own.
7. To operate the cordless feature of this microscope,
immediately plug in the microscope to charge for eight
(8) hours.
a. Plug in the round pin adapter from the power
supply to the back of your microscope.
b. Connect the opposite end to a Ken-A-Vision®
multicharger (Part # SCGN061) or an 110V
(220V international) electrical outlet.
NOTE: With one (1) overnight eight (8) hour charge, you can use the
microscope for up to forty (40) hours of continuous operation. The
cordless microscope can also be operated with the cord plugged into the
power source.
c. The best option, when not in use, is to plug the
microscope into a Ken-A-Vision multicharger
that will automatically stop charging once the
microscope is fully charged to keep it at the
3

optimal full charge for longer battery-life. This
prevents over charging and the user can charge
up to eight (8) microscopes at once.
d. Once finished charging, store the power cord in
the stow away integrated storage compartment
on the back of the microscope.
8. Plug the narrow end of the USB 2.0 cable into the back
of the camera body.
9. Plug the wide end of the USB 2.0 cable into the USB port
of your computer with the installed Applied Vision™
software.
10. To turn on the LED lights, locate the power switch on the
right back side of each microscope base.
11. Place a prepared slide on the stage and move it into
position for viewing.
12. Start with the 4x objective by raising the stage with the
coarse focus knobs until it will go no higher.
13. Lower the stage slowly to bring it into focus using the
coarse focus knobs.
14. To sharpen the image, adjust with the fine focus knobs.
15. Launch Applied Vision software.
16. The image that is being viewed through the eyepiece(s)
of the microscope should be displayed on the computer
screen.
17. Once the image appears on the computer screen,
simply turn the nosepiece to the next higher objective
lens and do minor adjustments with the fine focus knobs.
NOTE: If the image on the screen is flickering, reduce the amount of
light entering through the iris diaphragm and rheostat (light dimmer).
18. After obtaining focus of the specimen on the computer
screen, adjust the diopter on the eyepiece tube for
individual eye correction when viewing through the
microscope.
NOTE: The T-19641C binocular diopter is on the left eyepiece tube.
4

Product Number T-19541C T-19641C
Stand/Frame
SC12 Comp 2 Stand with 4 hole nose piece X X
SC12M Com
p
2 Mechanical Sta
g
e
X
X
SC12DP Comp 2 4 hole NP w/ upper/lower
light
Standard Features
Char
g
er Stora
g
eCom
p
artment
X
X
Stow and Go Handle™
X
X
Green Batter
y
™
X
X
Cordless Rechar
g
eable
X
X
COOL LIGHT™ illumination
X
X
Increased Ran
g
e of Focus
UPPER LIGHT STALK
Heads
SC12MH Comp 2 Monocular with eyepiece
SC12DH Comp 2 Dual View Head with 2
eyepieces
SC12BH Comp 2 Binocular Head with 2
e
y
e
p
ieces
SC12TH Comp 2Trinocular Head 2
e
y
e
p
ieces
SC12CMH Comp 2 Monocular with 3.2MP
Camera X
SC12CBH Comp 2 Binocular Head with 3.2MP
Camera X
Stage
SC12FS Comp 2 Floating Stage with built in
Condensor
SC12MS Comp 2 Mechanical Stage with
Built in Abbe XX
SC12SS Comp 2 Standard Stage with 5 Hole
Disc Diaphragm
Eyepieces
SC12EP5 5X
SC100EP10-19 10X
X
X
SC12EP16 16X
SC12EP20 20X
Objectives
SC12O B2 2X Plan DIN Achromat
SC12OB4 4X Plan DIN Achromat
X
X
SC12OB10 10X Plan DIN Achromat
X
X
SC12OB40
R
40X Plan DIN Achromat 0.65NA
X
X
XXtamorhcANIDX001R001BO21CS
Optional
T-12UG Comp 2 Mechanical Stage with Abbe
and 100X DIN Achromat Objective
SC12OB4
P
4X Plan
SC12OB10
P
10X Plan
SC12OB20
P
20X Plan
SC12OB40RP 40X Plan
SC12OB60RP 60X Plan
SC12OB100RP 100X Plan
SC12CMH Monocular Camera Head
SC12CBH Binocular Camera Head

5
Specificati ns

6
Tr ublesh ting
This section provides many useful tips on how to solve common problems
while setting up or using the Digital Comprehensive Scope 2 compound
microscope:
I can’t see an image. I can only see a partial image.
• Check to see if the USB plug is in the USB port of the
computer with installed Applied Vision™ software, or the
power supply is plugged into an electrical outlet, or the
battery is charged if using cordless.
• Check to see if the objective lens is clicked into place.
• Check to see if the LED lights are turned on by switching
the power button on the back of the microscope. A red
indicator light should glow if the LED lights are on.
• Check to see if the dimmer switch (rheostat) is turned
clockwise to allow the intensity of light to increase.
• Adjust the iris diaphragm, located underneath the stage,
to control the amount of light illuminating the prepared
slide.
• Close Applied Vision and then reboot Applied Vision
to activate the camera.
It is difficult to get an image in focus.
• Adjust the coarse focus knobs slowly.
• Check to see if the objective lens is clicked into place.
• If the image is focused on the computer screen, adjust
the diopter on the eyepiece tube to focus for the user’s
individual vision when viewing through the eyepiece.
• Check to see if there has been damage to the objective
lenses and eyepiece(s). If the lens/eyepiece is dirty, use
lens paper and distilled water to rub gently clean.
NOTE: Never rub the lens/eyepiece when it is dry. This can cause static
charge that will attract dirt.

C rp rate Headquarters
Ken-A-Visi n Mfg. C ., Inc.
5615 Raytown Road
Kansas City, O 64133 U.S.A.
Tel.: [phone]
Fax: [phone]
[email protected]
INS-SC12D
© 2011 Ken-A-Visi n Mfg. C ., Inc. All rights reserved. Other trademark names may be f their pr spective
wners. N part f the c ntents f this publicati n may be repr duced r transmitted in any f rm with ut the
written permissi n f Ken-A-Visi n Mfg. C ., Inc.
Ken-A-Visi n Mfg. C ., Inc. reserves the right t make design impr vements and ther changes in
acc rdance with the latest techn l gy. There is n bligati n t make changes in pr ducts already
manufactured.
www.kenavisi n.c m
Internati nal Office
Ken-A-Visi n Internati nal GmbH
Alte Bohle 33
D-50321 Brühl, Germany
Tel.: [phone]
Fax: [phone]
[email protected]