Kenmore 25378066890 User manual

Installing Your Air Conditioner
NOTE: These instructions describeinstallationin a typicalwood framed window with a wood SLIDE-BY sash,
or installation in a metal CASEMENT window. Modificationmay be necessary when installing in windows made
differentlythan those shown in these instructions.
A high window accessory kit is available for window heights up to 62" (1575mm).
TABLE OF CONTENTS
SUBJECT PAGE
MeetingElectricalRequirements 1
ElectricalConnection 2
PreparingForInstallation 2
InstallingUnitinaSlidingWindow 4
AlternateWindowJambApplications 7
InstallingUnitina CasementWindow 8
Optional Mounting Kit 11
appliance.
i,i
Failuretofollow
Ielectricalshock,
Meeting Electrical Requirements
OBSERVE ALL LOCAL GOVERNING CODES
AND ORDINANCES.
DO NOT, UNDER ANY CIRCUMSTANCES,
REMOVE THE POWER SUPPLY CORD
GROUNDING PRONG.
NOTE: If codes permit, and a separate
groundingwire is used; itis recommended that a
qualified electdcian determine that the grounding
path is adequate and not interrupted by plastic,
non-metallic gaskets, or other insulatii_gmaterials.
RECEPTACLE WIRING
Receptacle widng should be a minimum of 14
gauge, Use copper wire only. It is your responsibility
to provide proper and adequate receptacle widng,
installed by a qualified electdcian.
ELECTRICAL REQUIREMENTS
A 115 volt (103.5 minimum, 126.5 maximum), 60
Hertz, AC only, 15 ampere fused electdcal supply
isrequired. Atime delay fuse or time delay circuit
breaker is a_sorequired. Aseparate circuit, serving
onlythis appliance, MUST be provided.
P/N309000903 (9708)

Electrical Connection
Electrical ground isrequired on this appliance.
Recommended grounding method:
For your personal safety, this appliance must be
grounded. This air conditionerincludesa power
supply cord with a 3-prong grounding plug. To
minimize possible electricalshock hazard:
-cord must be plugged into a mating 3-prong
grounding-type wail receptacle,
-must be grounded in accordance with
National ElectricalCode (ANSI/NFPA 70-
latest version) and
-all local codes and ordinances.
Ifa mating 3-prong grounding-typewall receptacle is
not available, itis the responsibilityof the consumer
to have a property grounded 3-prong wall receptacle
installedby a qualified electrician.
3 Prong
GroundingPlug
3 Prong
GroundingType _
Wall Receptacle
Grounding
prong
PO(_6rfSeetPlPolyg_Ord
Preparing for Installation
Installation Tips
For wood-frame casement windows: It may be
necessary to constructa frame, using at least 1-inch
thickwood, with a 15-1/2-inch wide opening.
For brick or cement building construction: It may
be necessary to put a wood stool strip under AC, for
mounting purposes.
Tools Required
Flat-head screwdriver
Phillips-head screwdriver
Carpenter's level
Tape measure
Fine tooth saw
Electricor hand drill
2

1. Make sure you have all the necessary parts.
Installation kit contents:
1. Platform (1)
2. Support brace (1)
3. Adjustment bolt (1)
4. Hex flange nut - 1/4" (1)
5. Track seal (1)
6. Side channel seal (1)
7. Foam seal strip/Sash seal
8. Safety bracket (1)
9-11. Screw - #10x2-1/2" fiat-head (2), OR
Screw - #10xl-3/4" pan-heed (2), OR
Screw -#10xl" pan-heed (2)
12. Screw -#8x3/4" pan head (6)
13. Screw - #8-32x3/4" self-threading (7)
14. Window locking bracket (1)
15. Plasticwindow panel (1)
16. Side channel (2)
17. Screw -#8x3/8 truss head (6)
18. Panel frame/seal assembly (1)
T_,10,11
NOTE: Use scale below to measure length of your
screws.The scale will come in handy when
separating screws for installation.
(13mm) (25mm) (44mm) (63mm)
IDENTIFY SCREWS 1/2" 1" 1 3/4" 2 1/2"
LENOTIll, I
III!1 IIIIIIIIIIIIIllI
3/8" 3/4" 1 1/2" 2"
(10mmX19mm) (28mm) (50ram)
2. Choose aproper sized window, as shown right.
15-1/2 inches minimum width
16-1/4 inches maximum width (for
casement windows)
21-1/4 inches minimum height (with
window panel retainer)
20-5/16 inches minimum height
(window panel retainer removed)
39-7/16 inches maximum height
NOTE: He;ght measurement must be of a clear
opening above mountingplatform. In some cases,
due to a variety of stop and track arrangements, the
above dimensions may vary slightly. If necessary,
installationcan be made by alternating window
jambs. (See Alternate Window Jamb Applications.)
(continued) 3
15 _hinches
minimum _
width
205/,_ inches
minimum
height
39 V_6inches
maximum
height
16 V4inches
maximum
width
casement
windows)

3. Choose the proper window location.
Choose a window that allows the cooled air to flow
freely and directly intoroom(s) you wish to cool.
Remember, itis difficultto move air around comers.
Also, choose a window that is within 6 feet of an
electrical outlet. (See Meeting Electrical
Requirements/Receptacle wiring needs.) Do not
use an extension cord.
Installing Unit in a Sliding Window
1. Attach support brace to platform as shown.
Use adjustment bolt and hex flange nut to complete
assembly. Choose slot and adjustment bolt hole
IocaUonsthat willcreate a 45 degree angle between
platformand supportbrace. Try assembly in the
window to determine if platform will rest properly,and
allow proper slope (3/16-inch lower on outside).
NOTE: Ifyou are planning to use a siding-
protection board (see Step 5) on the outside of your
house, holdboard in place when testing assembly in
window.
2. Measure, and lightly mark a line 8-11116 Inches
from window Jamb.
NOTE: If any sash stop protrudes more than 1
inchfrom the side window jambs, the 8-11/16-inch
measurement must be increased accordingly.
Screen and storm window frames may also require
adjustments to the measurement.
3. Center platform assembly on the linewith inside
platform tab pressed against inside edge of window
track. Using the holes in the platform as a guide,
mark and drilltwo 9/64-inch diameter holes. Ddll
holes in either track or stool.
Property Damage Hazard-Failure to adhere to
the following precaution could result in
damage to window or air conditioner.
Be sure wood stool or window track is securely
attached to the building construction. Use longer
screws in sub-framing if necessary.
PlatformAssembly
Y4'(6mm) HEX FLANGE NUT
Center platform
assembly on the
line with platform
lab I_nmKI against
window track
(continued) 4

4. Peel off protective backing from track seal. Apply
seal to room side of window track. Center of seal strip
should coincidewith the linemarked in Step 2. The
two screw holesddlled in Step 3 should be directly
above seal stripin the innertrack.
Applyback seal
to window side
5. Securely attach a siding-protection board to
side of house.
NOTE: Siding-protectionboard should be long
enough to span 2 wall studs.
Inside
w_l of
house in_n
6. Place platform assembly, with platform tab
against inside of window track, and attach it to
window jamb. Use appropdate length screws (Items
9-11 in Prepadng For Installation).
7. Adjust platform assembly so that outside edge is
3/16-inch lower than inside edge, as shown right.
This ensures proper water drainage from the air
conditioner.
8. Level platform assembly from side-to-side.
Also, make sure windowtrack is level, Use leveling
shims as necessary to ensure unit is level from side-
to-side.
9. Measure he_ht of window opening from topof
platformassembly as shown dght. Subtract 20-5/8
inches. Mark this measurement on plastic window
panel, along the longer side. (continued)
tab=_mt
k_de o_
Out=Maleedgeis3/16_ch
Ioww than P.sk:le.
iT--

10, Clamp plastic window panel between a board
and awork table, and cut along cuffingline with a fine
tooth saw. Remove any burrs with a file.
11. Fasten side channels to the sides of the AC
using 3 screws (Item 17) per channel. Start with first
screw at top of channel. Make sure hook ends of
channels face toward back of unit.
12. Slide plastic window panel into panel frame,
with the smooth side to the room. Slide panel frame
assembly into side channels of the AC cabinet. Make
sure plasticwindow panel is firmlyenclosed onall
sides by the retainer grooves.
13. Cut side channel seal into 2 equal lengths.
Remove protective backing and apply it to the rear
side ofcabinet side channels, startingjust below
panelframe assembly. Pinch off excess length so
seal iseven with the bottom of the cabinet side
channel.
Fastening Side Channels
P_ window
Applyv_
jto llde
ch_
belowedgeo(
pw_ fTarne.
14. To remove front
1. Remove knobs by pullingfirmly, and then remove
dialplate.
2. Remove front retaining screw, whichis under the
dialplate.
3. Press firmlyon each side of the metal case close
to the front, approximately 2/3 ofthe way down.
4. While pressing on the sides of the metalcase,
gently pullthe front out and riftup to release it from
the case.
NOTE: DO NOT push or pull air directionlouvers.
15. Place AC in window opening. As shown right, it
shouldsit on platform assembly so that window panel
frame, and cabinet side channels are against top and
side window jambs. (continued)
Fro_
SlideInner
windowNBh 1_,,_]
f
f
6
JJ
J

16. Slide inner window sash firmly against side
of the cabinet, Make sure not to peel the seal strips
from the window track and cabinet side channels. If
the panel frame does not fit snugly to the inner
window sash, secure the panel frame to the sash
with #Sx3/4-inch screws, or #8-32x3/4-inch self-
threading screws. Use the partially plugged holes in
the panel frame. Drill 1/8-inch
pilot holes for the screws.
17. Hook the safety bracket over the base of the
unit and fasten it to the front of the platform
assembly. Use a #8-32x3/4-inch self-threading
screw.
NOTE: The bracket prevents movement of the
air conditioner (either in or out) after completing the
installation.
Install safety bracket
18. Stuff the foam seal strip/sash seal between
the vertical sash and the window glass, as shown
right.
19. Use the window locking bracket to lock the
innerwindow sash to the base of the outer window
sash. Use one #Sx3/4-inch screw, or #8-32x3/4-
inchself-threading screw. (Drill 1/8-inch pilothole).
20. Replace the air conditioner filter and front
panel frame. Make sure you replace the 2 screws
that hold the front panel frame in place!
Alternate Window Jamb
Applications
To install in windows having no flanges or wood stops
on the top and side jambs, the channels and panel
frame must fit against amating flange (or 1/16-inch
max. thick angle) attached to the window jambs.
Figure A shows this angle installed. Figures B & C
show alternate treatments. On the sash side of the
opening, the leading corner of the inner sash
becomes the flange. You can purchase the angle
strip locally.
A B C
Add _u_gleto Add wood Md 16- or 18-
•_ood stop _ _.tt'_ G_tugoangdo
7

Installing the Unit in a Casement
Window
NOTE: Open the window the maximum amount to
allow for clearance of the cabinet. The crank handle
should be removed to allowthe platformto be
fastened to the jamb. If the window cannot open far
enough (more than 15-1/2 inches) for the cabinet to
clear the window, remove the window entirely by
drillingout the rivets. Bolts can serve as the pivots in
the future.
To avoidcrank handle and window clearance
problems, the unitcan be installed in a stationary
sash section. However, the horizontal mullionand the
2 glass panels must be removed before installation.
1. Attach Support brace to platform as shown. Use
the adjustment bolt and hex flange nut to complete
the assembly. Choose the slot and adjustmentbelt
hole locationsthat will create a 45 degree angle
between the platform and the supportbrace. Try the
assembly in the window to determine ifthe platform
will restproperly, and allow the proper slope (3/16-
inchlower on outside).
NOTE: Ifyou are planning to use a siding-
protectionboard (see Step 6) on the outsideof your
house,hold the board in place when testingthe
assembly in the window.
2. Drill a9/64-Inch diameter pilot hole in the
window jamb an equal distance from each side of the
jamb, and 3/16-inch up from the window sill. If the
hole coincides with the window lever slot in the jamb
bottom, an additional hole will have to be drilled
through the platform edge and the window jamb to
miss this slot.
3. Peel off the protective backing from the track
seal, and stick the seal to the window sill on the
outside of the bottom jamb.
1/4"(6ram)HEXFLANGENUT
Equal distance from bo_l sides
It111. Inchel
Platform Assembly
4. Screw the platform assembly to the window
jamb through the pilot hole you drilled in Step 2. Use
a#8x3/4-inch self-threading screw. (continued)
8

5.Adjust the platform assemblysothattherearof
theairconditionerwillbe3/16-inchlowerthanthe
front.Thisensuresproperwaterdrainagefromthe
airconditioner.
NOTE: A projection below the base ofthe air
conditionerwill require the rear of the platformto be
7/16-inch lower than the front to create the 3/18-inch
slant from front to rear.
6. Securely attach a siding-protection board to the
side of the house where the platform assembly hitthe
house.The siding-protectionboard should be long
enough to span 2 wall studs.
Rear 18_t kmst
7/16" lower
than f_clt
F_t_ _Ung-
/rotoc_onboardto
the house siding.
7. Measure the height of the window opening
from the top of the platform assembly. Subtract
20-5/8 inches. Mark this measurement on the plastic
window panel, along the longer side.
8. Clamp the plastic window panel between a
board and a work table, and cut along the cuttingline
with a fine tooth saw. Remove any burrswith a file.
9. Fasten the side channels to the sides of the
unit using three screws (item 17) per channel. Make
sure hook ends of channels face toward the back of
unit.
10. Slide the plastic window panel into the panel
frame with the smooth side to the outside. Slide the
panel frame assembly into the side channels of the
air conditioner cabinet. Make sure the plastic window
panel is firmly enclosed on all sides by the retainer
grooves. (continued)
PI wi

11. Cut side channel seal into 2 equal lengths.
Remove the protective backing and apply it tothe
rear side of the cabinet side channels, startingjust
belowthe panel frame assembly. Pinchoff excess
length so the seal is even with the bottom of the
cabinet side channel.
At_lywqahw
Mto side
emmmv=
tx_w K_e e_
_ frae_
12. To remove front
1. Remove knobs by pullingfirmly,and then remove
dial plate.
2. Remove front retaining screw,which is under the
dial plate.
3. Press firmly on each side ofthe metal case close
to the front, approximately 2/3 ofthe way down.
4. While pressing on the sides of the metal case,
gently pull the front out and liftup to release it from
the case.
NOTE: DO NOT push or pull air directionlouvers.
Scn_
f
/
J
13. Place the air conditioner in the window
opening as shown to the right. It should siton the
platform assembly so that the window panel frame,
and the cabinet side channels are against the top and
side window jambs. Side channels shouldoverlap
side window jambs equally.
14. Drill two 9/64-Inch diameter pilot holes in the
top window jamb in linewith the partiallyplugged
holesin the panel frame. Secure the panel fame to
the window jamb with two #8-32x3/4-inch self-
threading screws. If additional holdingis necessary,
two screws may be used on the sides of the panel
frame as well.
15. Drill two screw-clearance holes in the cabinet
side channels (near bottom) and two 9/64-inch
diameter pilot holes in the side window jambs. Secure
the cabinet side channels to the window jambs with
two #8-32x3/4-inch self-threading screws. When
doing this, be careful not to twist the side channel
seals with the screws.
NOTE: Inserting screws will prevent the air
conditioner from being pushed into the room.
(continued)
tO