Kenwood DDX7035 User manual

DDX7035
DDX7045
DDX7065
MONITOR WITH DVD RECEIVER
INSTALLATION MANUAL
附DVD接收機顯示器
安裝說明書
附DVD接收機顯示器
安裝說明書
DVD수신기장착 모니터
설치설치
설치설치
설치 설명서설명서
설명서설명서
설명서
© PRINTED IN JAPAN B54-4432-00/00 (M)(AI)
Downloaded from: http://www.usersmanualguide.com/

English
2English
Before Installation
..........1
..........2
..........1
..........1
..........1
1
..........6
6
..........6
7
2
3
4
5
Accessories
Downloaded from: http://www.usersmanualguide.com/

English 3
1. To prevent a short circuit, remove the key from the
ignition and disconnect the -battery.
2. Make the proper input and output wire connections for
each unit.
3. Connect the speaker wires of the wiring harness.
4. Connect the wiring harness wires in the following order:
ground, battery, ignition.
5. Connect the wiring harness connector to the unit.
6. Install the unit in your car.
7. Reconnect the -battery.
8. Press the reset button.
If you connect the ignition wire (red) and the battery wire
(yellow) to the car chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
•If your car's ignition does not have an ACC position,
connect the ignition wires to a power source that can be
turned on and off with the ignition key. If you connect the
ignition wire to a power source with a constant voltage
supply, as with battery wires, the battery may die.
•If the console has a lid, make sure to install the unit so
that the faceplate will not hit the lid when closing and
opening.
•If the fuse blows, first make sure the wires aren’t
touching to cause a short circuit, then replace the old
fuse with one with the same rating.
•Insulate unconnected wires with vinyl tape or other
similar material. To prevent a short circuit, do not remove
the caps on the ends of the unconnected wires or the
terminals.
•Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail
to work if you share the -wires or ground them to any
metal part in the car.
•When only two speakers are being connected to the
system, connect the connectors either to both the front
output terminals or to both the rear output terminals (do
not mix front and rear). For example, if you connect the
+connector of the left speaker to a front output
terminal, do not connect the -connector to a rear
output terminal.
•After the unit is installed, check whether the brake
lamps, blinkers, wipers, etc. on the car are working
properly.
•Mount the unit so that the mounting angle is 30° or less.
2CAUTION
2WARNING
Installation Procedure
Downloaded from: http://www.usersmanualguide.com/

Connection
4English
English
If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground),
you may cause a short circuit, that in turn may start a fire. Always connect those wires to the
power source running through the fuse box.
2WARNING
A
B
C
B
C
PRK SW
( 5A )
–+
+
B
C
A
For the sake of safety, be sure to connect the parking sensor.
Connect to the vehicle's parking brake detection switch harness
using the supplied relay connector.
2CAUTION
Parking sensor wire (Green)
Ground wire (Black) -(To car chassis)
Battery wire
(Yellow)
Ignition key
switch
Battery
Car fuse box
ACC
Battery wire (Yellow)
Dimmer control wire (Orange/White)
To car light control switch
Ignition wire (Red)
Ground wire (Black) -(To car chassis)
Motor antenna control wire
(Blue)
Power control wire
(Blue/White)
External amplifier control wire
(Pink/Black)
FM/AM antenna input
Car fuse
box
(Main fuse)
Depending on what antenna you are using,
connect either to the control terminal of the motor
antenna, or to the power terminal for the booster
amplifier of the film-type antenna.
When using the optional power amplifier, connect
to its power control terminal.
To "EXT.AMP.CONT." terminal of the amplifier
having the external amp control function.
Downloaded from: http://www.usersmanualguide.com/

English 5
MUTE
ANT. CONT
P CONT
EXT.CONT
+
+
+
+
ILLUMI
White/Black
NOTE
To front left speaker
To front right speaker
To rear left speaker
To rear right speaker
Mute wire (Brown)
White
Gray/Black
Gray
Green/Black
Green
Purple/Black
Purple
Wiring harness
(Accessory 2)
Wiring harness
(Accessory 1)
Rear view
Connect to the terminal that is grounded when either the telephone
rings or during conversation.
To connect the KENWOOD navigation system, consult your
navigation manual.
Downloaded from: http://www.usersmanualguide.com/

English
6English
Connection
System Connection
REARFRONT
AV IN
AV OUT
WOOFER
SUB
•Audio/Visual input
Visual input (Yellow)
Audio left input (White)
Audio right input (Red)
•Audio/Visual Output
Visual output (Yellow)
Audio left output (White)
Audio right output (Red)
•Sub-woofer (Mono) Preout
Audio left output (White)
Audio right output (Red)
•Rear Preout
Audio left output (White)
Audio right output (Red)
•Front Preout
Audio left output (White)
Audio right output (Red)
Wire an optical cable after fixing it with the clamp
on the back of the unit.
Do not bend the optical cable within a minimum
radius of 30 mm, or it may be damaged.
When you install the unit, ensure that the optical
cable is not stuck between the unit and the
vehicle parts.
2CAUTION
To Navigation System To TV Tuner unit
To DSP unit
Optical input for
DSP unit
To Disc Changer etc.
optical cable
clamp
≥30R
Downloaded from: http://www.usersmanualguide.com/

English 7
Installation
Make sure that the unit is installed securely in place. If the unit is
unstable, it may malfunction (eg, the sound may skip).
Bend the tabs of the mounting sleeve
with a screwdriver or similar utensil
and attach it in place.
Accessory 4
Metal mounting strap
(commercially available)
Self-tapping screw
(commercially available)
Firewall or metal support
Screw (M4X8)
(commercially available)
Installation for Monitor/Player Unit
Downloaded from: http://www.usersmanualguide.com/

English
8English
Installation
Accessory 6or 7
Accessory 6or 7
Accessory 3
(For NISSAN Car)
Bracket
Installing in Japanese-Made Cars
Downloaded from: http://www.usersmanualguide.com/

English 9
1. Engage the catch pins on the removal tool 5and
remove the two locks on the lower level.
Lower the frame and pull it forward as shown in the
figure.
2. When the lower level is removed, remove the upper
two locations.
The frame can be removed from the top side in the
same manner.
1. Refer to the section <Removing the Hard Rubber
Frame> and then remove the hard rubber frame.
2. Remove the Hex-head screw with integral washer (M4 ×
6) on the back panel.
3. Insert the two removal tools 5deeply into the slots on
each side, as shown.
4. Lower the removal tool toward the bottom, and pull out
the unit halfway while pressing towards the inside.
Be careful to avoid injury from the catch pins on the
removal tool.
5. Pull the unit all the way out with your hands, being
careful not to drop it.
■Removing the Hard Rubber Frame (escutcheon)
■Removing the Unit
Removing Monitor/Player Unit
Accessory 5
Catch
Lock
Accessory 5
Downloaded from: http://www.usersmanualguide.com/

中文繁體字
10
中文繁體字
安裝之前
附件
1
.................. 1
2
.................. 1
3
.................. 1
4
.................. 1
5
.................. 2
6
.................. 6
7
.................. 6
Downloaded from: http://www.usersmanualguide.com/

中文繁體字
11
安裝程序
1. 為了防止短路﹐從點火開關中拔出鑰匙﹐拆下蓄電池的負
極-接線。
2. 連接各裝置的輸入､輸出導線。
3. 連接電線束的揚聲器導線。
4. 按照接地導線､蓄電池導線和點火導線的順序連接電線
束。
5. 將電線束的連接器連接到裝置上。
6. 將裝置安裝到汽車中。
7. 重新連接蓄電池的負極 -接線。
8. 按下復位按鈕。
2警告
如果您將點火裝置電線紅和電池線黃連接到汽車底
盤接地﹐您可能會導致短路﹐並造成火災。請始終將那
些電線連接到經過保險絲盒的電源。
2注意
•如果汽車的點火裝置沒有ACC位置﹐請將點火導線與可以
通過點火鑰匙接通和斷開的電源連接。如果將點火導線與
始終供電的電源連接﹐例如與蓄電池導線連接﹐蓄電池將
全部放電而無法使用。
•如果控制台設有蓋板﹐在安裝時請注意﹐當關閉和打開面
板時﹐不得與蓋板碰撞。
•當保險絲燒斷時﹐請首先確認不應有引起短路的接觸﹐然
後使用與舊保險絲相同規格的保險絲更換。
•請用乙烯帶等絕緣物包覆未連接的導線。為了防止發生短
路﹐不得取下未連接導線的線端或端子的護罩。
•將揚聲器導線直接與對應的端子連接。如果共用負極 -
導線或者將其與汽車的金屬部件連接﹐本裝置可能損壞
或者無法正常工作。
•當衹有兩衹揚聲器與系統連接時﹐請將連接器或者與兩個
前側輸出端子連接､或者與兩個後側輸出端子連接不得
將前側與後側混合連接。例如﹐如果將左側揚聲器的正
極+ 連接器與前側輸出端子連接﹐則不得將負極 -連接
器與後側輸出端子連接。
•安裝結束後﹐請確認汽車制動器燈､方向指示燈和刮水器
等是否正常動作。
•本機安裝角度為30度以下為宜。
Downloaded from: http://www.usersmanualguide.com/

中文繁體字
12
中文繁體字
A
B
C
B
C
PRK SW
( 5A )
–+
+
B
C
A
手剎車傳感器電線綠
連接
2警告
如果您將點火裝置電線紅和電池線黃連接到汽車底盤接地﹐您可
能會導致短路﹐並造成火災。請始終將那些電線連接到經過保險絲盒的電源。
使用配備的中繼連接器連接到汽車的手剎車檢測開關線束。
2注意
為了安全､請確保連接手剎車傳感器。
FM/AM 天線輸入
汽車保險絲盒
(主保險絲)汽車保險絲盒
ACC
點火開關
電池
電池線黃
點火裝置電線紅
接地線黑-連接到汽車底盤
減光控製電線橙/白
連接到燈光控製開關
功率控製電線藍/白
電動天線控製電線藍
外部放大器控製電線
粉紅/黑
根據您使用天線的情況､請連接到電動天線
的控製端子､或者連接到薄膜型天線增強放
大器的功率端子。
當使用選購的功率放大器時､請連接
到它的功率控製端子。
連接到有外部放大器控製功能的放大器
EXT.AMP.CONT外部放大器控製端子。
電池線黃
接地線黑-連接到汽車底盤
Downloaded from: http://www.usersmanualguide.com/

中文繁體字
13
MUTE
ANT. CONT
P CONT
EXT.CONT
+
+
+
+
ILLUMI
後視
靜音導線棕色
電線線束
附件 1
連接到電話振鈴或通話時接地的端子上。
註
請參照導航系統的使用說明書､連接KENWOOD
導航系統。
白/黑
白
灰/黑
灰
綠/黑
綠
紫/黑
紫
向前置左揚聲器
向前置右揚聲器
向後置左揚聲器
向後置右揚聲器
電線線束
附件 2
Downloaded from: http://www.usersmanualguide.com/

中文繁體字
14
中文繁體字
REARFRONT
AV IN
AV OUT
WOOFER
SUB
連接
系統連接
•音頻左輸出(白)
音頻右輸出(紅)
•后預輸出
音頻左輸出(白)
音頻右輸出(紅)
•低音揚聲器 (單聲道) 預輸出
音頻左輸出(白)
音頻右輸出(紅)
•音頻/視頻輸入
視頻輸出(黃)
音頻左輸出(白)
音頻右輸出(紅)
•音頻/視頻輸出
視頻輸入 (黃)
音頻左輸入 (白)
音頻右輸入 (紅)
至導航系統 至TV調諧器裝置
至DSP裝置
DSP裝置的光學輸入
至光盤換片機等
2注意
在本機的背面使用夾子固定後﹐連接光學連接線。
不得以小於30mm的半徑彎曲光學連接線､否則將發生
損壞。
在安裝本機時､不得將光學連接線夾在本機和車輛部件
之間。
夾子
光學連接線
≥30R
Downloaded from: http://www.usersmanualguide.com/

中文繁體字
15
安裝顯示器/播放裝置
安裝
隔熱牆或金屬支撐
自攻絲螺絲
選購
螺絲M4×8
選購
附件 4
安裝套盒用螺絲刀
等折彎凸耳部位﹐
將其固定。
請切實固定裝置。若安裝不穩﹐可能會出故障。
金屬安裝固定
夾板選購
Downloaded from: http://www.usersmanualguide.com/

中文繁體字
16
中文繁體字
連接
在日本汽車上安裝時
附件 6或者 7
托架
附件 6或者 7
附件 3
對於NISSAN
日產牌汽車
Downloaded from: http://www.usersmanualguide.com/

中文繁體字
17
拆除顯示器/播放裝置
■硬橡膠框的拆卸方法
1. 拉出可拆工具 5的凸耳﹐拆卸下側兩處的鎖定裝置。
按圖示要領將框向下壓﹐再向後拉出。
2. 下側拆卸後﹐上側兩處也以同樣方法拆卸。
從上側開始也可同樣拆卸。
■拆卸方法
1. 請參照硬橡膠框的拆卸方法拆卸硬橡膠框。
2. 卸下背面板附有的墊圈螺絲M4×6。
3. 將可拆工具 5深深插入裝置的槽內。
4. 將可拆工具向下降﹐靠近內側﹐將裝置拉出到中途。
安裝時請注意不要被可拆工具的凸耳碰傷。
5. 用手托住裝置拉出﹐以免掉落。
附件 5
附件 5
鎖定裝置
凸耳
Downloaded from: http://www.usersmanualguide.com/

中文簡體字
18
中文簡體字
安裝之前
附件
...................... 〈
...................... 〈
...................... 〈
...................... 〈
...................... 〉
...................... 6
...................... 6
1
2
3
4
5
6
7
Downloaded from: http://www.usersmanualguide.com/

中文簡體字
19
安裝程序
〈. 為了防止短路從點火開關中拔出鑰匙拆下蓄電池的負
極 - 接線。〉. 連接各裝置的輸入輸出導線。3. 連接電線束的揚聲器導線。4. 按照接地導線蓄電池導線和點火導線的順序連接電線
束。5. 將電線束的連接器連接到裝置上。6. 將裝置安裝到汽車中。7. 重新連接蓄電池的負極 - 接線。8. 按下復位按鈕。2警告
如果您將點火裝置電線紅和電池線黃連接到汽車底
盤 接地您可能會導致短路並造成火災。請始終將那
些電線連接到經過保險絲盒的電源。2注意
‧如果汽車的點火裝置沒有ACC位置請將點火導線與可以
通過點火鑰匙接通和斷開的電源連接。如果將點火導線與
始終供電的電源連接例如與蓄電池導線連接蓄電池將
全部放電而無法使用。‧如果控制台設有蓋板在安裝時請注意當關閉和打開面
板時不得與蓋板碰撞。‧當保險絲燒斷時請首先確認不應有引起短路的接觸然
後使用與舊保險絲相同規格的保險絲更換。‧請用乙烯帶等絕緣物包覆未連接的導線。為了防止發生短
路不得取下未連接導線的線端或端子的護罩。‧將揚聲器導線直接與對應的端子連接。如果共用負極 -
導線或者將其與汽車的金屬部件連接本裝置可能損壞
或者無法正常工作。‧當衹有兩衹揚聲器與系統連接時請將連接器或者與兩個
前側輸出端子連接或者與兩個後側輸出端子連接不得
將前側與後側混合連接。例如如果將左側揚聲器的正
極 + 連接器與前側輸出端子連接則不得將負極 - 連接
器與後側輸出端子連接。‧安裝結束後請確認汽車制動器燈方向指示燈和刮水器
等是否正常動作。‧本機安裝角度為30度以下為宜。
Downloaded from: http://www.usersmanualguide.com/

中文簡體字
20
中文簡體字
A
B
C
B
C
PRK SW
( 5A )
–+
+
B
C
A
手剎車傳感器電線綠
連接
2警告
如果您將點火裝置電線紅和電池線黃連接到汽車底盤接地您可
能會導致短路並造成火災。請始終將那些電線連接到經過保險絲盒的電源。使用配備的中繼連接器連接到汽車的手剎車檢測開關線束。
2注意
為了安全請確保連接手剎車傳感器。接地線黑-連接到汽車底盤
電池線黃
”M/AM 天線輸入
汽車保險絲盒
(主保險絲) 汽車保險絲盒
ACC
點火開關
電池
電池線黃
點火裝置電線紅
接地線黑-連接到汽車底盤
減光控製電線橙/白
連接到燈光控製開關
功率控製電線藍/白
電動天線控製電線藍
外部放大器控製電線
粉紅/黑
根據您使用天線的情況請連接到電動天線
的控製端子或者連接到薄膜型天線增強放
大器的功率端子。當使用選購的功率放大器時請連接
到它的功率控製端子。連接到有外部放大器控製功能的放大器
“XT.AMP.CONT外部放大器控製端子。
Downloaded from: http://www.usersmanualguide.com/