Kenwood LZH-80TJ4 User manual

OVERHEAD CONSOLE WITH 8” LCD SCREEN
LZH-80TJ4
INSTRUCTION MANUAL
© B64-3951-00 (MW)
B64-3951-0000LZH-80TJ4.indd1B64-3951-0000LZH-80TJ4.indd1 07.7.231:27:56PM07.7.231:27:56PM

2|LZH-80TJ4
Safety precautions Notes
• The illustrations of the display and the panel
appearing in this manual are examples used to
explain more clearly how the controls are used.
Therefore, what appears on the display in the
illustrations may differ from what appears on
the display on the actual equipment, and some
of the illustrations on the display may represent
something impossible in actual operation.
Cleaning the Unit
If this unit is stained, wipe it with a dry soft cloth
such as a silicon cloth.
If this unit is stained badly, wipe the stain off with a
cloth moistened with neutral cleaner, then wipe it
again with a clean soft dry cloth.
¤
• Applying spray cleaner directly to the unit may affect
its mechanical parts. Wiping this unit with a hard cloth
or using a volatile liquid such as thinner or alcohol may
scratch the surface or erases characters.
Screen brightness during low
temperatures
When the temperature of the unit falls such as
during winter, the liquid crystal panel’s screen will
become darker than usual. Normal brightness will
return after using the monitor for a while.
2WARNING
To prevent injury or fire, take the
following precautions:
• To prevent a short circuit, never put or leave any
metallic objects (such as coins or metal tools)
inside the unit.
• Do not touch the liquid crystal fluid if the LCD
is damaged or broken due to shock. The liquid
crystal fluid may be dangerous to your health or
even fatal.
If the liquid crystal fluid from the LCD contacts
your body or clothing, wash it off with soap
immediately.
2CAUTION
To prevent damage to the machine, take
the following precautions:
• Make sure to ground the unit to a negative 12V
DC power supply.
• Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of
water splashing.
• Do not use your own screws. Use only the screws
provided. If you use the wrong screws, you could
damage the unit.
• If smoke or abnormal odor is detected, turn off
the unit immediately and contact the dealer.
Using the unit continuously can result in fire or
other accidents.
• Be sure to have the unit repaired by the dealer.
If you repair the unit, fire or other accidents can
result.
B64-3951-0000LZH-80TJ4.indd2B64-3951-0000LZH-80TJ4.indd2 07.7.231:27:57PM07.7.231:27:57PM

English |3
Components names and Functions
1 2 43
1Monitor release knob
Unlock the motor.
2Dome light switch
"ON": The light goes on.
"DOOR": The light goes on/out with the
opening/closing of vehicle doors.
"OFF": The light goes out.
3IR transmitter
4Audio/ Visual input 2 terminal
• Visual input (Yellow)
• Audio left input (White)
• Audio right input (Red)
⁄
• The picture input to the Audio/Visual input 2 terminal
can be displayed by selecting "AV-IN2" as described in
<Video Source Selection> (page 4).
Open the monitor
Monitor release knob
1Unlock the monitor
Press the monitor release knob.
2Open the monitor
Press the monitor downward.
⁄
• Do not press the LCD of the monitor when opening
the monitor. The LCD can damage.
• When closing the monitor, press its back until it locks.
If the monitor is not closed completely, the monitor is
held powered.
B64-3951-0000LZH-80TJ4.indd3B64-3951-0000LZH-80TJ4.indd3 07.7.231:27:57PM07.7.231:27:57PM

4|LZH-80TJ4
Operations
POWER
INPUT
/MENU
SCRN/
DIM/
POWER INPUT SCRN DIM
Video Source Selection
Press the [INPUT] button.
Each time the button is pressed, the video source
switches as follows:
Display Setting
"AV-IN1" Select the AV1 INPUT source.
"AV-IN2" Select the AV2 INPUT source.
Power
Turns power ON or OFF
Press the [POWER] button.
Display information
When you press the [INPUT] button, the status of
the monitor is displayed.
Mode Full
I R 2 MHz
AV-IN2
1
3
2
1Screen mode Display
2IR headphones output frequency display
3Video source Display
⁄
• The information display is cleared automatically after
approximately 5 seconds.
B64-3951-0000LZH-80TJ4.indd4B64-3951-0000LZH-80TJ4.indd4 07.7.231:27:58PM07.7.231:27:58PM

English |5
⁄
• The "TIN" can be adjusted when NTSC video signal is
input.
• The screen select can be set for each source.
• If you make no operation for 15 seconds, this mode
is automatically canceled.
Picture Quality setting
You can adjust the picture quality control of the
monitor.
1Enter Picture Quality setting mode
Press the [MENU] button for at least 2
seconds.
2Select the screen for brightness ("BRT")
setting
Press the [SCRN] or [DIM] button for at least
2 seconds.
Pressing the button for at least 2 seconds
toggles between the "Day" screen (for daytime
brightness setting) and the "Night" screen (for
nighttime brightness setting).
3Select the adjusting item
Press the [MENU] button.
Each time the button is pressed, the adjusting
item switches.
Ｓｃｒｅｅｎ Ｃｏｎｔｒｏｌ
Ｎｉｇｈｔ
4Adjust the item
Press the [2] or [3] button.
Item Button Setting
"BRT" [3]
[2]
Brighter screen
Darker screen
"TIN" [3]
[2]
Stronger red level
Stronger green level
"COL" [3]
[2]
Deeper color
Paler color
"CONT" [3]
[2]
Stronger contrast
Less contrast
"BLK" [3]
[2]
Less black level
Stronger black level
5Exit Picture Quality setting mode
Press the [MENU] button for at least 2
seconds.
Selection of Screen Brightness
Setting
You can switch between the daytime screen
brightness and nighttime screen brightness
adjusted in the Picture Quality setting mode.
Press the [DIM] button.
Pressing the [DIM] button toggles between the
daytime screen brightness and nighttime screen
brightness adjusted in the Picture Quality setting
mode.
B64-3951-0000LZH-80TJ4.indd5B64-3951-0000LZH-80TJ4.indd5 07.7.231:27:58PM07.7.231:27:58PM

6|LZH-80TJ4
Operations
IR Headphones frequency setting
You can select the IR Headphones frequency you
wish.
Press the [SCRN] button for at least 2 seconds.
Each time the button is pressed for at least
2 seconds, the frequency output switches as
follows:
Display Setting
"2 MHz" The output frequency of IR Headphones is
set to 2 MHz.
"3 MHz" The output frequency of IR Headphones is
set to 3 MHz.
Switching Screen mode
Press the [SCRN] button.
Each time the button is pressed, the screen
mode switches as follows:
Display Setting
"Full" Full picture mode.
"Just" Justify picture mode.
"Cinema" Cinema picture mode.
"Zoom" Zoom picture mode.
"Normal" Normal picture mode.
B64-3951-0000LZH-80TJ4.indd6B64-3951-0000LZH-80TJ4.indd6 07.7.231:27:59PM07.7.231:27:59PM

English |7
Specifications
Monitor Unit
Screen size
: 8 inches wide
Display system
: Transparent TN LCD panel
Drive system
: TFT active matrix system
Number of pixels
: 336,960 pixels (480 H × 234 V × RGB)
Effective pixels
: 99.99 %
Pixel arrangement
: RGB striped arrangement
Back lighting
: Cold cathode tube
IR Transmitter output
: (2MHz) L ch: 2.3 MHz/ R ch: 2.8 MHz
: (3MHz) L ch: 3.2 MHz/ R ch: 3.8 MHz
Colour system
: NTSC/PAL
External video input level (RCA jacks)
: 1 ± 0.1 Vp-p/ 75 Ω
External audio input level (RCA jacks)
: 1 V/ 100 KΩ
Audio output level (RCA jacks)
: 1 V/ 100 Ω
Specifications subject to change without notice.
General
Operating voltage
: 14.4 V DC (11 - 16 V)
Current consumption
: 1500 mA
Consumed Power
: 22 W
Operational temperature range
: –10 °C to +60 °C
Storage temperature range
: –30 °C to +85 °C
Dimensions (W × H × D)
: 280 × 237 × 42 mm
Weight
: 1.4 kg
Dome Lamp Unit
Operating voltage
: 14.4 V DC (11 - 16 V)
Current consumption
: 200 mA
Consumed Power
: 2.9 W
Although the effective pixels for the liquid crystal panel is
given as 99.99% or more, 0.01% of pixels may not light or
may light incorrectly.
B64-3951-0000LZH-80TJ4.indd7B64-3951-0000LZH-80TJ4.indd7 07.7.231:27:59PM07.7.231:27:59PM

B64-3951-0000LZH-80TJ4.indd8B64-3951-0000LZH-80TJ4.indd8 07.7.231:27:59PM07.7.231:27:59PM