Kenwood FleetSync KDS-100 User manual

MOBILE DATA TERMINAL
TERMINAL DE DONNEES POUR MOBILE
TERMINAL MÓVIL DE DATOS
TERMINALE MOBILE PER DATI
MOBILE DATENTERMINAL
MOBIELE DATA TERMINAL
KDS-100
INSTRUCTION MANUAL
MODE D’EMPLOI
MANUAL DE INSTRUCCIONES
MANUALE DI ISTRUZIONI
BEDIENUNGSANLEITUNG
GEBRUIKSAANWIJZING
© B62-1480-00 (M)
09 08 07 06 05 04 03 02 01 00
KENWOOD CORPORATION

MOBILE DATA TERMINAL
INSTRUCTION MANUAL
KENWOOD CORPORATION
KDS-100

i
THANK YOU!
We are grateful you chose KENWOOD for your mobile applications. We believe
this mobile data terminal will provide dependable communications to keep
personnel operating at peak efficiency.
KENWOOD incorporates the latest in advanced technology in all our products.
As a result, we feel strongly that you will be pleased with the quality and features
of this product.
NOTICES TO THE USER
◆Government law prohibits the operation of unlicensed transmitters within the territories under
government control.
◆Illegal operation is punishable by fine and/or imprisonment.
◆Refer service to qualified technicians only.
PRECAUTIONS
Please observe the following precautions to prevent fire, personal injury, and
equipment damage.
• Do not attempt to configure the terminal while driving; it is too dangerous.
• Do not modify the terminal for any reason.
• Do not place the terminal in excessively dusty, humid, or wet areas, nor on unstable
surfaces.
• Do not touch the surface of the terminal after it has been sitting in a hot environment
for extended periods; the terminal body will rise in temperature and may burn you.
• If an abnormal odor or smoke is detected coming from the terminal, turn OFF the
power immediately. Contact your KENWOOD dealer.

ii
CONTENTS
UNPACKING AND CHECKING EQUIPMENT ................................... 1
SUPPLIED ACCESSORIES ..................................................................... 1
PREPARATION .................................................................................. 2
TOOLS REQUIRED .............................................................................. 2
INSTALLING THE TERMINAL ................................................................... 2
ORIENTATION.................................................................................... 3
FRONT PANEL ................................................................................... 3
OPERATION ....................................................................................... 4
BEFORE YOU START ........................................................................... 4
POWER ............................................................................................. 4
MESSAGE DISPLAY MODE ................................................................... 4
NEW MESSAGES ........................................................................... 4
OLD MESSAGES............................................................................ 5
MESSAGE LIST MODE ......................................................................... 6
SENDING MESSAGES........................................................................... 7
STATUS ....................................................................................... 7
SELCALL ..................................................................................... 8
MENU MODE ..................................................................................... 8
TERMINAL SETTINGS ........................................................................... 9
VOLUME LEVEL ............................................................................ 9
DISPLAY BACKLIGHT ...................................................................... 9
DISPLAY LINES ........................................................................... 10
DISPLAY CONTRAST .................................................................... 10
MESSAGE UTILITIES..................................................................... 11
CLOCK ...................................................................................... 11

1
UNPACKING AND CHECKING EQUIPMENT
Note: The following unpacking instructions are for use by your KENWOOD dealer, an authorized
KENWOOD service facility, or the factory.
Carefully unpack the terminal. We recommend that you identify the items listed
in the following table before discarding the packing material. If any items are
missing or have been damaged during shipment, file a claim with the carrier
immediately.
SUPPLIED ACCESSORIES
metI rebmuNtraP ytitnauQ
tekcarbgnitnuomesaBXX-9860-92J1
tekcarbgnitnuomraeRXX-0960-92J1
teswercSXX-5202-99N1
swercstnemtsujdaraeRXX-6450-80N2
launamnoitcurtsnIXX-0841-26B1
Base mounting braket Rear mounting bracket
Screw set Rear adjustment screws

2
Note: The following preparation instructions are for use by your KENWOOD dealer, an authorized
KENWOOD service facility, or the factory.
TOOLS REQUIRED
Note: Before installing the terminal, always check how far the mounting screws will extend below the
mounting surface. When drilling mounting holes, be careful not to damage vehicle wiring or parts.
The following tools are required for installing the terminal:
• 6 mm (1/4 inch) or larger electric drill
• 4.2 mm (5/32 inch) drill bit for the self-tapping screws
INSTALLING THE TERMINAL
For passenger safety, install the terminal securely, using the supplied mounting brackets, so the
terminal will not break loose in the event of a collision.
1Mark the position of the holes in the dash by using the base mounting bracket
as a template. Drill the holes, then attach the base mounting bracket using
the supplied self-tapping screws.
• Be sure to mount the terminal in a location where the controls are within easy
reach of the user.
2Connect the rear mounting bracket to the back of the terminal using the
supplied screws.
3Connect the terminal cable to the mobile unit.
• The mobile unit must have the optional KCT-34 or KCT-35
cable installed. The appropriate cable depends on the
transceiver type.
• An optional KCT-36 extension cable (12 feet/ 3 m)
is also avaible.
4Secure the terminal to the mounting bracket
using the supplied rear adjustment screws.
• Adjust the angle of the terminal before
tightening the screws, so that you
can easily view the display and
panel keys.
PREPARATION

3
ORIENTATION
FRONT PANEL
qq
qq
qDisplay
Messages appear on this 240 x 64 dot LCD.
ww
ww
wLED Indicator (default settings)
Lights red while “talking” to the mobile unit. Lights green while “listening”to the
mobile unit. Flashes orange when a message is waiting.
ee
ee
eMENU key
Press to enter the Menu mode, in order to select your desired menu.
rr
rr
rKeys 1 ~ 5
Press these function keys to perform the functions described in the status bar
on the display, directly above the keys.
tt
tt
tSEL (Select) key
Press to select the displayed item.
yy
yy
y▲key
Press to scroll up the display.
uu
uu
u▼key
Press to scroll down the display.
q
ert
y
u
w

4
OPERATION
BEFORE YOU START
The displays provided within this manual are for your reference only. Actual
displays may vary according to how your terminal is set up.
POWER
This terminal does not have a power switch. Power is supplied directly through
the cable attached to the mobile unit.
MESSAGE DISPLAY MODE
■NEW MESSAGES
When a message is received, the first few lines appear on the display. To
read the message immediately, press [READ] (key 1). To acknowledge that
you know there is a new message, simply press [OK] (key 5).
When you read the message, depending on its size, you may have to scroll
down to view the entire message. A small arrow at the bottom right of the
display will indicate whether or not you can scroll down. To scroll up and
down, use the ▲and ▼keys.

5
■OLD MESSAGES
The key functions are:
[RESPOND] (key 1) allows you to respond to the displayed message.
Pressing this key allows you to respond to the message by sending a STATUS
or SELCALL (key 1or 2).
[↓PAGE] (key 2) allows you to scroll down the screen, 1 complete screen at a
time. Press and hold this key for approximately 1 second to change the
display from page scroll to message scroll. The key name changes to
[↓MSG] and you can scroll down the screen, 1 line at a time.
[↑PAGE] (key 3) allows you to scroll up the screen, 1 complete screen at a
time. Press and hold this key for approximately 1 second to change the
display from page scroll to message scroll. The key name changes to
[↑MSG] and you can scroll up the screen, 1 line at a time.
[CHK/DEL] (key 4) allows you to mark the displayed message as read
(checked), prepare the message for deletion, or uncheck/ undelete the
message. Pressing this key once marks the message as read by placing a
check icon at the right of the display. Pressing this key a second time (while
the check icon is displayed) marks the message for deletion by placing a
delete icon in place of the check icon. Pressing this key a third time (while the
delete icon is displayed) unmarks the message.
[EXIT] (key 5) exits the display.

6
MESSAGE LIST MODE
Exiting a specific message allows you to view a list of all your messages. You
can scroll through your list of messages using the ▲and ▼keys.
The first screen of key functions in the message list are:
[RESPOND] (key 1) allows you to respond to the selected message. Pressing
this key allows you to respond to the message by sending a STATUS or
SELCALL (key 1or 2).
[↓PAGE] (key 2) allows you to scroll down the screen, 1 complete screen at a
time. Press and hold this key for approximately 1 second to move the display to
the end of the list.
[↑PAGE] (key 3) allows you to scroll up the screen, 1 complete screen at a time.
Press and hold this key for approximately 1 second to move the display to the
beginning of the list.
[FROM]/ [TIME] (key 4) allows you to change the characteristics of the message
list display between the date and time the message was received and the name
of the sender. Pressing this key when FROM is displayed changes the message
list to the name of the sender. Pressing this key when TIME is displayed returns
the message list to the date and time the message was received.
[MORE] (key 5) allows you to display additional functions (refer to the second
screen list, below).
The second screen of key functions in the message list are:
[SORT] (key 1) allows you to sort your message list. Pressing this key allows
you to choose betweenTIME, NAME, TITLE, ICON, and DELETE MESSAGE.
Select your desired sorting method using the ▲and ▼keys, then press
[EXECUTE] (key 1). A confirmation message will appear, allowing you to delete
any messages which you have set for deletion.
[↓PAGE] (key 2) allows you to scroll down the screen, 1 complete screen at a
time. Press and hold this key for approximately 1 second to move the display to
the end of the list.

7
[↑PAGE] (key 3) allows you to scroll up the screen, 1 complete screen at a time.
Press and hold this key for approximately 1 second to move the display to the
beginning of the list.
[RETURN] (key 5) allows you to return to the first screen list.
SENDING MESSAGES
You can respond to messages by pressing [RESPOND] (key 1). You will be
given the option to send a [STATUS] (key 1) or a [SELCALL] (key 2).
Note: If your dealer does not set up the Function Program key, [RESPOND] will not appear until you
press a key from 1 ~ 5.
■STATUS
When selecting a status, a list appears with preset messages. Scroll through
the list using the ▲and ▼keys to select your desired status.
If you are making a status call in response to a message, you already have a
selected recipient. However, if you are making a new message, you must also
select a recipient by pressing [TO] (key 4). Use the ▲and ▼keys to select
your desired recipient from the list in your terminal.
Once you have selected a status message and recipient, press [SEND]
(key 1). A message will appear on the display, confirming that you are
sending the data. If there is no response from the recipient, you are given an
option to [RETRY] (key 1) or [CANCEL] (key 5).

8
■SELCALL
If you are making a selcall in response to a message, transmission begins as
soon as you press [SELCALL]. However, if you are making a new selcall,
select a recipient using the ▲and ▼keys to scroll through the list in your
terminal, then press [CONNECT] (key 1). A message will appear on the
display, confirming that you are calling the recipient.
MENU MODE
To enter Menu mode, press the MENU key momentarily. In Menu mode, you are
given the following options:
[STATUS] (key 1) allows you to make a status call. Refer to “Sending
Messages”, above.
[SELCALL] (key 2) allows you to make a selcall call. Refer to “Sending
Messages”, above.
[REMOTE] (key 3) allows you to use the terminal as a remote controller for your
mobile unit. Keys 1 ~ 5 function as follows: System/Group Up, System/Group
Down, Group/Channel Up, Group/Channel Down, and Exit Remote Mode
(respectively). The ▲and ▼keys function as volume up and volume down. The
display shows the operating system/group and group/channel.
Note: The REMOTE key may not appear on some transceivers.
[CANCEL] (key 5) returns you to the previous display.

9
TERMINAL SETTINGS
By entering the Settings mode, you can adjust the terminal volume level, the
display backlight brightness, the number of lines that appear on the display, the
display contrast, the message settings, and the clock.
To enter Settings mode, press and hold the MENU key for approximately
1 second. Refer to the following sub-sections for instructions on how to
adjust each setting.
■VOLUME LEVEL
1Press [VOLUME] (key 1) to adjust the volume level.
2Press the ▼key to decrease the volume or the ▲key to increase the
volume.
■DISPLAY BACKLIGHT
1Press [B.LIGHT] (key 2) to adjust the brightness of the display backlight.
2Press the ▼key to decrease the brightness or the ▲key to increase the
brightness.

10
■DISPLAY LINES
1Press [LINES] (key 3) to change the number of text lines that appear on
the display.
2Press the ▲or ▼key to scroll through the text line options, as follows:
■DISPLAY CONTRAST
1Press [CONTRAS] (key 4) to adust the contrast of the display.
2Press the ▼key to decrease the contrast or the ▲key to increase the
contrast.
Received text message:6 lines
Other display screens: 6 lines
Received text message:3 lines
Other display screens: 5 lines
Received text message:5 lines
Other display screens: 5 lines
Received text message:3 lines
Other display screens: 6 lines

11
■MESSAGE UTILITIES
1Press [MORE] (key 5) to view the second screen of terminal settings.
• Press [RETURN] (key 5) to return to the first screen of terminal settings.
2Press [MSG UTY] (key 1) to enter the message utility settings.
3Press the ▲or ▼key to select a message from the message list.
4Press [SELECT] (key 2) to select the current message for restoration
(remove the message from the delete list) or [FROM] (key 4) to change the
display between the date and time the message was received and the
name of the sender (at which time TIME will appear on the display in place
of FROM).
5Press [EXECUTE] (key 1) to perform an action that you have selected, or
press [CANCEL] (key 5) to cancel your current operation.
■CLOCK
1Press [MORE] (key 5) to view the second screen of terminal settings.
• Press [RETURN] (key 5) to return to the first screen of terminal settings.
2Press [TIME] (key 2) to adjust the date and time.
3Press the ▼key to decrease the values or the ▲key to increase the
values.
4Press [←](key 1) to move the cursor to the left and [→](key 2) to move
the cursor to the right.
5Press [ADJUST] (key 4) to complete the setting, or press [CANCEL]
(key 5) to cancel your current operation.

TERMINAL DE DONNEES POUR MOBILE
MODE D’EMPLOI
KENWOOD CORPORATION
KDS-100

F-i
MERCI!
Nous sommes heureux que vous ayez choisi KENWOOD pour vos applications mobiles.
Nous croyons que ce terminal de données mobile permettra à votre personnel d’effectuer des
transmissions fiables pour un rendement optimum.
KENWOOD incorpore la fine pointe de la technologie dans tous ses produits. Nous sommes
donc convaincus que vous apprécierez la qualité et les caractéristiques de ce produit.
AVIS AUX UTILISATEURS
◆Une loi gouvernementale interdit l’usage sans licence d’un émetteur-récepteur sur les territoires
régis par l’autorité gouvernementale.
◆Une utilisation illégale est passible d’amende ou d’emprisonnement.
◆Pour l’entretien et la réparation, confiez l’appareil uniquement à des techniciens qualifiés.
PRÉCAUTIONS
Veuillez prendre les précautions suivantes pour éviter les risques d’incendie, de blessure
corporelle ou d’endommagement de l’appareil.
• Ne tentez pas de configurer le terminal tout en conduisant, car cela est trop dangereux.
• Ne tentez pas de modifier votre terminal pour aucune raison que ce soit.
• Ne placez pas l’appareil dans un endroit trop poussiéreux ni trop humide; ne le placez pas sur
une surface instable.
• Ne touchez pas à la surface du terminal si l’appareil est demeuré longtemps dans un endroit
chaud; la température du boîtier pourrait être très élevée et vous pourriez vous brûler.
• Si vous remarquez une odeur ou une fumée anormale qui se dégage du terminal, mettez-le
immédiatement hors tension. Contactez votre détaillant KENWOOD.

F-ii
TABLE DES MATIERÈS
DÉBALLAGE ET VÉRIFICATION DE L’ÉQUIPEMENT ................................1
ACCESSOIRES FOURNIS ...................................................................................1
PRÉPARATION ...............................................................................................2
OUTILS REQUIS..............................................................................................2
INSTALLATION DU TERMINAL ............................................................................. 2
ORIENTATION.................................................................................................3
PANNEAU AVANT ............................................................................................3
FONCTIONNEMENT.......................................................................................4
AVANT DE COMMENCER...................................................................................4
ALIMENTATION ................................................................................................4
MODE D’AFFICHAGE DES MESSAGES.................................................................4
NOUVEAUX MESSAGES ..............................................................................4
ANCIENS MESSAGES .................................................................................5
MODE LISTE DE MESSAGES .............................................................................6
ENVOI DE MESSAGES ......................................................................................7
ÉTAT .......................................................................................................7
SELCALL .................................................................................................8
MODE MENU .................................................................................................8
RÉGLAGES DU TERMINAL .................................................................................9
VOLUME ..................................................................................................9
RÉTROÉCLAIRAGE DU VISUEL .....................................................................9
LIGNES D’AFFICHAGE ..............................................................................10
CONTRASTE D’AFFICHAGE .......................................................................10
UTILITAIRES POUR LES MESSAGES ............................................................ 11
HORLOGE .............................................................................................. 11

F-1
DÉBALLAGE ET VÉRIFICATION DE L’ÉQUIPEMENT
Remarque: Les instructions de déballage suivantes sont à l’intention de votre détaillant KENWOOD,
d’un centre de service autorisé KENWOOD ou de l’usine.
Déballez soigneusement le terminal. Prenez soin de vérifier la présence des articles
ci-dessous avant de vous débarrasser du matériel d’emballage. Si certains articles manquent
ou s’ils ont été endommagés durant le transport, déposez immédiatement une réclamation
auprès du transporteur.
ACCESSOIRES FOURNIS
elcitrA ecèiPedorémuN étitnauQ
esabedegatnomedtroppuSXX-9860-92J1
erèirraegatnomedtroppuSXX-0960-92J1
sivedueJXX-5202-99N1
erèirratnemetsuja’dsiVXX-6450-80N2
iolpme’dedoMXX-0841-26B1
Support de montage de base Support de montage arrière
Jeu de vis Vis d’ajustement arrière

F-2
Remarque: Les instructions préparatoires suivantes sont à l’intention de votre détaillant
KENWOOD, d’un centre de service autorisé KENWOOD ou de l’usine.
OUTILS REQUIS
Remarque: Avant d’installer le terminal, vérifiez toujours jusqu’à quelle profondeur les vis de
montage se rendront sous la surface de montage. Évitez d’endommager le câblage ou les pièces du
véhicule lorsque vous percez des trous de montage.
Vous aurez besoin des outils suivants pour l’installation du terminal:
• Perceuse électrique de 6 mm ou plus
• Foret de 4,2 mm pour les vis taraudeuses
INSTALLATION DU TERMINAL
Pour la sécurité des occupants, veuillez assujettir solidement le terminal au moyen des supports de
montage fournis, afin d’éviter que le terminal ne se dégage en cas de collision.
1Marquez la position des trous sur le tableau de bord en utilisant le support de montage de
base comme gabarit. Percez les trous, puis fixez le support de montage de base au
moyen des vis taraudeuses fournies.
• Installez le terminal à un endroit où l’utilisateur aura aisément accès aux commandes.
2Fixez le support de montage arrière au dos du
terminal au moyen des vis fournies.
3Connectez le câble du terminal à l’unité mobile.
• Le câble optionnel KCT-34 ou KCT-35 doit être
installé sur l’unité mobile. Le câble spécifique dépend
du type d’émetteur-récepteur.
• Un câble de rallonge optionnel KCT-36 de 3 m est
aussi offert.
4Assujettissez le terminal au support de montage au
moyen des vis d’ajustement arrière (fournies).
• Réglez l’angle du terminal avant de serrer les vis,
afin que le visuel et les touches du panneau avant
soient bien visibles.
PRÉPARATION