KEPCO BOP-GL 1KW User manual

KEPCO®
THE POWER SUPPLIER™
MODEL
OPERATOR’S MANUAL
ORDER NO.
KEPCO, INC. 131-38 SANFORD AVENUE FLUSHING, NY. 11355 U.S.A. TEL [phone] FAX [phone]
email: [e-mail] World Wide Web: http://www.kepcopower.com
KEPCO INC.
An ISO 9001 Company.
BOP-GL 1KW
HIGH POWER BIPOLAR POWER SUPPLY
OPTIMIZED FOR INDUCTIVE LOADS
(LOW NOISE, RIPPLE, DRIFT AND TEMPERATURE COEFFICIENT)
BOP-GL 1KW
POWER SUPPLY
©2015, KEPCO, INC
P/N 243-1293-y
IMPORTANT NOTES:
1) This manual is valid for the following Firmware Versions:
FIRMWARE VERSION NOTE.
2) A Change Page may be included at the end of the manual. All applicable changes and
revision number changes are documented with reference to the equipment serial num-
bers. Before using this Instruction Manual, check your equipment firmware version num-
ber to identify your model. If in doubt, contact your nearest Kepco Representative, or the
Kepco Documentation Office in New York, [phone], requesting the correct revision
for your particular model and firmware version number.
3) The contents of this manual are protected by copyright. Reproduction of any part can be
made only with the specific written permission of Kepco, Inc.
Data subject to change without notice.
3.05andhigher

228-1348 DC-COMP/INST 111315 A
Declaration of Conformity
Application of Council directives: 73/23/EEC (LVD)
93/68/EEC (CE mark)
Standard to which Conformity is declared:
EN61010-1:1993 (Safety requirements for electrical equipment for measurement,
control and laboratory use)
Manufacturer's Name and Address: KEPCO INC.
131-38 SANFORD AVENUE
FLUSHING, N.Y. 11355 USA
Importer's Name and Address:
Type of Equipment: Component Power Supply
Model No.: [PRODUCT MODEL NUMBER]
Year of Manufacture:
I, the undersigned, declare that the product specified above, when used in conjunction with the condi-
tions of conformance set forth in the product instruction manual, complies with the requirements of the
Low Voltage Directive 73/23/EEC, which forms the basis for application of the CE Mark to this product.
Place: KEPCO Inc.
131-38 Sanford Ave.
Flushing, N.Y.11355 USA
Date:
Saul Kupferberg
(Full Name)
VP OF SALES
(position)
REPRESENTATIVECOPY

B228-1529 COND/CONFORM 111315
Conditions of Conformance
When this product is used in applications governed by the requirements of the EEC, the following restric-
tions and conditions apply:
1. For European applications, requiring compliance to the Low Voltage Directive, 73/23/EEC, this power
supply is considered a component product, designed for “built in“ applications. Because it is incom-
plete in construction, the end product enclosure must provide for compliance to any remaining electri-
cal safety requirements and act as a fire enclosure. (EN61010-1 Cl. 6, Cl. 7, Cl.8, Cl. 9 and EN61010-
1 annex F)
2. This power supply is designed for stationary installation, with mains power applied via a detachable
power supply cord or via direct wiring to the source power terminal block.
3. This power supply is considered a Class 1 (earthed) product, and as such depends upon proper con-
nection to protective earth for safety from electric shock. (EN61010-1 Cl. 6.5.4)
4. This power supply is intended for use as part of equipment meant for test, measurement and labora-
tory use, and is designed to operate from single phase, three wire power systems. This equipment
must be installed within a suitably wired equipment rack, utilizing a three wire (grounded) mains con-
nection. See wiring section of this manual for complete electrical wiring instructions. (EN61010-1 Cl.
6.5.4 and Cl.6.10.1)
5. This power supply has secondary output circuits that are considered hazardous, and which exceed
100V d-c, able to deliver current greater than 10A d-c.
6. The output wiring terminals of this power supply have not been evaluated for field wiring and, there-
fore, must be properly configured by the end product manufacturer prior to use.
7. This power supply employs a supplementary circuit protector in the form of a circuit breaker mounted
on the front panel. This circuit breaker protects the power supply itself from damage in the event of a
fault condition. For complete circuit protection of the end product, as well as the building wiring, it is
required that a primary circuit protection device be fitted to the branch circuit wiring. (EN61010-1 Cl.
9.6.2)
8. Hazardous voltages are present within this power supply during normal operation. All operator adjust-
ments to the product are made via externally accessible switches, controls and signal lines as speci-
fied within the product operating instructions. There are no user or operator serviceable parts within
the product enclosure. Refer all servicing to qualified and trained Kepco service technicians.

228-1352 SAFETY - (COVER REMOVAL) 111315 C
SAFETY INSTRUCTIONS
1. Installation, Operation and Service Precautions
This product is designed for use in accordance with EN 61010-1 and UL 3101 for Installation Category 2,
Pollution Degree 2. Hazardous voltages are present within this product during normal operation. The prod-
uct should never be operated with the cover removed unless equivalent protection of the operator from
accidental contact with hazardous internal voltages is provided:
2. Grounding
This product is a Class 1 device which utilizes protective earthing to ensure operator safety.
3. Electric Shock Hazards
This product outputs hazardous voltage and energy levels as a function of normal operation. Operators
must be trained in its use and exercise caution as well as common sense during use to prevent accidental
shock.
There are no operator serviceable parts or adjustments within the product enclosure.
Refer all servicing to trained service technician.
Source power must be removed from the product prior to performing any servicing.
This product is factory-wired for the nominal a-c mains voltage indicated on the rat-
ing nameplate located adjacent to the source power connection on the product's rear
panel. To reconfigure the product input for other nominal mains voltages as listed
herein, the product must be modified by a trained service technician.
The PROTECTIVE EARTHING CONDUCTOR TERMINAL must be properly con-
nected prior to application of source power to the product (see instructions on instal-
lation herein) in order to ensure safety from electric shock.
PROTECTIVE EARTHING CONDUCTOR TERMINAL - This symbol indicates the
point on the product to which the protective earthing conductor must be attached.
EARTH (GROUND) TERMINAL - This symbol is used to indicate a point which is
connected to the PROTECTIVE EARTHING TERMINAL. The component installer/
assembler must ensure that this point is connected to the PROTECTIVE EARTH-
ING TERMINAL.
CHASSIS TERMINAL -This symbol indicates frame (chassis) connection, which is
supplied as a point of convenience for performance purposes (see instructions on
grounding herein). This is not to be confused with the protective earthing point, and
may not be used in place of it.
This symbol appears adjacent to any external terminals at which hazardous voltage
levels as high as 500V d-c may exist in the course of normal or single fault condi-
tions.
This symbol appears adjacent to any external terminals at which hazardous voltage
levels in excess of 500V d-c may exist in the course of normal or single fault condi-
tions.
!
!
!
!
!

DOP-SAFETY 111315
OPERATOR
SAFETY INSTRUCTIONS
Read these safety instructions, as well as the applicable installation and operating instructions contained in
this manual before using the power supply.
Do not touch the output terminals. The output is dangerous. Electric shock can cause injury or death.
Do not remove the cover or disassemble the unit. There are no operator serviceable components or
adjustments inside the unit. High voltage components inside the unit can cause serious injury even with
input power disconnected.
Service must be referred to authorized personnel. Using the power supply in a manner not specified by
Kepco. Inc. may impair the protection provided by the power supply. Observe all safety precautions noted
throughout this manual. The following table lists symbols used on the power supply or in this manual where
applicable.
The liquid in the LCD is hazardous: do not lick or swallow. Wash skin and clothes immediately and thor-
oughly upon exposure.
CAUTION
If this power supply is used in OEM equipment, the OEM equipment manufacturer is responsible for
attaching appropriate warning labels on the OEM equipment.
Operating the power supply outside the specified limits for input voltage, temperature, or other environ-
mental conditions noted in this manual can damage the power supply and void the warranty.
DO NOT: wipe the front panel with hard materials, nor apply excessive force to the surface. DO NOT
expose to extended periods of bright sunshine or UV light.
Safety Messages
The BOP protection circuitry is designed to protect the load against unregulated high voltages and protect
the BOP from extensive damage in the event of a component failure. Refer to Table 1-2 for more informa-
tion regarding the protection circuits.
SAFETY SYMBOLS
SYMBOL Meaning
WARNING: RISK OF ELECTRIC SHOCK.
INDICATES THE POSSIBILITY OF BODILY INJURY OR DEATH.
CAUTION: REFER TO REFERENCED PROCEDURE.
INDICATES THE POSSIBILITY OF EQUIPMENT DAMAGE.
WARNING
!

LIST OF
WARNINGS AND CAUTIONS
BOP 1KW OPR 11/13/15 E
PAGE WARNING/CAUTION
3-9 WARNING: For inductive loads, and especially superconducting magnet type loads,
the inherent offset of the BOP in the OFF state may generate significant
current in the circuit. A properly rated switch in parallel with a resistor
must be connected between the power supply and the load. The switch
must be open and voltage and current measurements at the output must
read 0V, 0A before removing or installing connections between BOP and
load.
3-9 WARNING: For both inductive loads and constant-current-type active electronic
loads when the BOP output is set to OFF, a path is provided for absorbing
either the energy accumulated in the reactance of the load during the ON
state, or energy delivered by an electronic load. This prevents damage to
the load and power supply as well as providing safety for the user. How-
ever, In addition to the built-in safety features, constant-current-type ac-
tive electronic loads must be adjusted to zero and voltage and current
measurements at the output must read 0V, minimum current, before han-
dling the power supply-to-load connections.
3-10 WARNING: Accessing the BOP after the output is disabled in BATTERY mode is haz-
ardous because (1) high current arcing is possible and (2) either the ex-
ternal battery voltage, or the voltage (±Voltage Protection max) on the
BOP output terminals may be dangerous. Therefore, for battery and con-
stant-voltage-type active electronic loads it is recommended that two
properly rated external switches be installed for safety: one in series with
the battery, and one across the BOP output. After the unit is set to OFF,
first open the switch in series with the battery, then close the switch
across the BOP output to ensure safety before handling BOP connec-
tions. When connecting the battery, the switch across the output should
be opened after the connections are complete and then the switch in se-
ries with the battery should be closed. If the constant-voltage-type active
electronic load is adjusted to zero before handling the power supply-to-
load connections, only the switch across the BOP output is required.
4-8 WARNING: The sense resistor will be dissipating full rated current of the BOP. If it is
hot to the touch, the sense resistor value, power rating and/or cooling are
incorrect; refer to PAR. 4.3 and Table 4-2.

FBOP 1KW OPR 11/13/15
LIST OF
WARNINGS AND CAUTIONS
PAGE WARNING/CAUTION
2-8 CAUTION: it is recommended that source power of external equipment connected to
the Analog Port be applied through an isolating transformer to avoid
ground loops or possible damage to the BOP due to incorrect equipment
a-c wiring (e.g., defeating of ground connection).
2-10 CAUTION: DO NOT repeatedly toggle the POWER circuit breaker/switch as this may
damage the unit.
2-11 CAUTION: DO NOT repeatedly toggle the POWER circuit breaker/switch as this may
damage the unit.
2-11 CAUTION: The rack must provide support at the rear (within 6 inches of the rear pan-
el). Optional slides can also be used (see PAR. 2.4.2).
2-12 CAUTION: When working with active loads, the voltage or current of the active load
must not exceed the maximum voltage or current rating of the BOP. Oth-
erwise the overvoltage or overcurrent protection will shut down the pow-
er supply.
2-14 CAUTION: Never connect the load to the sense terminals. Monitoring instruments
(e.g., DVM, etc.) are the only external equipment that may be safely con-
nected to the sense terminals.
2-14 CAUTION: Never connect the BOP OUTPUT terminal (or the load terminal tied to the
OUTPUT terminal) to earth-ground. Otherwise, if the controlling device is
grounded, the BOP canbe damaged by the protection limitoutput current
flowing inside the BOP along the programming signal return path.
2-14 CAUTION: Do not connect both the load and the programming device return (com-
mon) to earth-ground potential. Otherwise, If the COMMON power con-
nection between the BOP and the load is lost, then the BOP can be
damaged by output current flowing inside the BOP along the program-
ming signal return path.
2-14 CAUTION: The safety features incorporated into the BOP to handle energy from Ac-
tive loads are unable to protect the power supply or the load if input pow-
er to the BOP is lost or if the BOP Malfunctions. It is recommended that
the user monitor “Power OK” flag pins 3 and 4 of the external Protect Port
(see Table 2-6) and implement a fast-acting means of disconnecting ca-
pacitive loads or crowbarring inductive loads to prevent damage to both
the BOP and the load in the event of input power loss.
2-19 CAUTION: For both parallel and series configurations, remove links between (COM
S) and (COM OUT) terminals of all slaves to prevent damage to the unit
and maintain system accuracy. Make sure to accurately follow Figures 2-
7 through 2-10 for proper connection of the units.
2-25 CAUTION: For both parallel and series configurations, remove links between (COM
S) and (COM OUT) terminals of all slaves to prevent damage to the unit
and maintain system accuracy. Make sure to accurately follow Figures 2-
7 through 2-10 for proper connection of the units.

LIST OF
WARNINGS AND CAUTIONS
BOP 1KW OPR 11/13/15 G/(H Blank)
PAGE WARNING/CAUTION
3-1 CAUTION: Before connecting a load, note that the unit is will power-up with the con-
figuration set by the power-up switches accessible through the top cover
(see Table 2-2 forswitchsettings). Verify that these power-up settings are
compatible with your load (see Figure 2-2 and Table 2-2 for switch set-
tings).
To change to change load type, baud rate or Trigger port Remote on/off
logic refer to PAR. 3.3.2.1; to change all other power-up settingslisted be-
low refer to PAR. 3.3.2.2.
In addition to the power-up settings determined by the switches ac-
cessed through the top cover, many unit parameters may besavedfor the
next power-up cycle using MEM:UPD commands (see PAR. B.12). When
using MEM:UPD, it is recommended that the unit be tagged with the cus-
tom power-up configuration to avoid unexpected behavior upon power-
up.
3-4 CAUTION: DO NOT repeatedly toggle the circuit breaker/switch as this may damage
the unit.
3-5 CAUTION: DO NOT repeatedly toggle the circuit breaker/switch as this may damage
the unit.
3-7 CAUTION: When working with active loads, always adjust the BOP protection limits
to be above the maximum values of voltage or current expected from the
load. For example, when the BOP is operating in voltage mode sinking
energy from a constant current type load, set the current protection limits
of the BOP above the maximum current expected from the load.
3-22 CAUTION: The commands listed above with (**) will generate a “-440, Missing Que-
ry” error if a query does not precede the command in the same command
string or ;*OPC? does not follow the command. Although commands not
marked with (**) will not generate an error, all commands listed above re-
quire verification to insure absolute success. Failure to follow these
rules can result in the loss of all stored constants and render the unit in-
operative.
3-23 CAUTION: If you are not sure what the saved settings are, disconnect the load be-
fore issuing *RCL. Then issue queries to identify the stored settings.
3-34 CAUTION: When the serial port has received an XOFF, the error message -400, “Que-
ry Error” will be placed in the queue to indicate the loss of transmitted in-
formation due to a received XOFF character. When XON is received, the
unit will transmit all data in it's buffer followed by the exclamation char-
acter (!). This (!) character is not part of any message from the BOP and
indicates the transmission buffer has been cleared and the BOP is idle.
B-5 CAUTION: When using MEM:UPD it is recommended that the unit be tagged with the
saved configuration to avoid unexpected behavior upon power-up.

BOP-1K 111315 i
TABLE OF CONTENTS
SECTION PAGE
SECTION 1 - INTRODUCTION
1.1 Scope of Manual ..................................................................................................................................... 1-1
1.2 General Description................................................................................................................................. 1-1
1.3 Specifications.......................................................................................................................................... 1-1
1.4 Remote Control....................................................................................................................................... 1-13
1.5 Features.................................................................................................................................................. 1-13
1.5.1 Digital Calibration............................................................................................................................... 1-13
1.5.2 voltage/current Protection.................................................................................................................. 1-13
1.5.3 Waveforms......................................................................................................................................... 1-13
1.5.4 Saving and Recalling Settings........................................................................................................... 1-14
1.5.5 External Reference (Analog Control)................................................................................................. 1-14
1.5.6 External Limits................................................................................................................................... 1-14
1.5.7 User-defined Voltage/Current Maximum Values (Software Limits) ................................................... 1-14
1.5.8 Parallel and Series Configurations .................................................................................................... 1-14
1.5.9 Energy Recuperation......................................................................................................................... 1-14
1.6 Equipment Supplied................................................................................................................................ 1-15
1.7 Accessories............................................................................................................................................. 1-15
1.8 Safety...................................................................................................................................................... 1-15
SECTION 2 - INSTALLATION
2.1 Unpacking and Inspection....................................................................................................................... 2-1
2.2 Terminations and Controls ...................................................................................................................... 2-1
2.3 Preliminary Operational Check................................................................................................................ 2-9
2.3.1 Preliminary Operational Check using Analog Control........................................................................ 2-9
2.3.2 Preliminary Operational Check using Digital Control......................................................................... 2-10
2.4 Installation............................................................................................................................................... 2-11
2.4.1 Rack Mounting................................................................................................................................... 2-11
2.4.2 Slide Installation................................................................................................................................. 2-11
2.5 Wiring Instructions................................................................................................................................... 2-12
2.5.1 Safety Grounding............................................................................................................................... 2-12
2.5.2 Source Power Connections............................................................................................................... 2-12
2.5.3 D-C Output Grounding....................................................................................................................... 2-12
2.5.3.1 Grounding Network Configuration................................................................................................ 2-13
2.5.4 Power Supply/Load Interface............................................................................................................. 2-13
2.5.5 Load Connection - General................................................................................................................ 2-14
2.5.6 Load Connection Using Local Sensing.............................................................................................. 2-14
2.5.7 Load Connection Using Remote Sensing.......................................................................................... 2-14
2.6 Cooling .................................................................................................................................................... 2-15
2.7 Setting up the unit ................................................................................................................................... 2-15
2.7.1 Power-up Settings ............................................................................................................................. 2-15
2.7.2 Setup for Analog Control................................................................................................................... 2-17
2.7.3 Setup for Digital Control via GPIB ..................................................................................................... 2-17
2.7.4 Setup for Digital Control via RS 232C ............................................................................................... 2-17
2.8 Multiple Unit Configurations .................................................................................................................... 2-19
2.8.1 Multiple Unit Connections.................................................................................................................. 2-19
2.8.2 Multiple Unit Source Power............................................................................................................... 2-24
2.8.3 Multiple Unit Protection...................................................................................................................... 2-24
2.8.4 Operating Instructions for Multiple Unit Combinations....................................................................... 2-25
2.8.5 Restoring a Unit to Standalone Operation......................................................................................... 2-26

ii BOP-1K 111315
TABLE OF CONTENTS
SECTION PAGE
SECTION 3 - OPERATION
3.1 General................................................................................................................................................... 3-1
3.2 Power-up Settings .................................................................................................................................. 3-1
3.2.1 Changing the Default Power-up Settings.......................................................................................... 3-2
3.3 Power Supply Basics.............................................................................................................................. 3-2
3.3.1 Controls and Indicators..................................................................................................................... 3-2
3.3.2 Turning the Power Supply On........................................................................................................... 3-3
3.3.2.1 Reset Power-up .......................................................................................................................... 3-4
3.3.2.2 Normal Power-up........................................................................................................................ 3-4
3.3.3 Voltage and Current Parameters...................................................................................................... 3-5
3.3.4 Voltage/Current Protect Settings ...................................................................................................... 3-5
3.3.4.1 Hidden Voltage and Current Protect Limits................................................................................. 3-5
3.3.5 Maximum/Minimum Protection Limits (Software-controlled)............................................................. 3-7
3.3.5.1 Maximum Accepted Voltage or Current (Main Channel Software Limits)................................... 3-7
3.3.6 Determining How the Unit responds when Output is OFF (Load Type)............................................ 3-9
3.3.6.1 Battery Charging/Discharging using the BOP............................................................................. 3-11
3.3.6.1.1 Battery Operations using Voltage Mode.................................................................................3-11
3.3.6.1.2 Battery Operations using Current Mode.................................................................................3-11
3.3.7 External Limits .................................................................................................................................. 3-12
3.3.8 Enabling/Disabling DC Output Power............................................................................................... 3-12
3.3.8.1 Remote Shutdown....................................................................................................................... 3-12
3.3.8.2 Remote On-OFF Using Trigger Port Pin 2.................................................................................. 3-14
3.3.8.3 Remote On-OFF Using Trigger port (off) and Digital Command (on)......................................... 3-14
3.3.8.4 Remote On-OFF Using Digital Commands................................................................................. 3-14
3.3.9 Setting Main Channel Mode (Voltage or Current)............................................................................. 3-15
3.3.10 Protection Limits ............................................................................................................................... 3-15
3.4 Analog Remote Mode Programming ...................................................................................................... 3-16
3.4.1 Controlling the Output Using the BOP as a Power Amplifier............................................................ 3-16
3.4.1.1 Fixed Gain using External Reference Control............................................................................. 3-17
3.4.1.2 Variable Gain Using External Reference Level........................................................................... 3-18
3.4.2 External Protection Limits................................................................................................................. 3-19
3.4.2.1 Using Lesser of Digital vs. Analog (External) limits..................................................................... 3-19
3.4.3 Monitoring Output Current Using an analog signal........................................................................... 3-20
3.5 Digital Control......................................................................................................................................... 3-20
3.5.1 Password Protection......................................................................................................................... 3-20
3.5.2 Setting Operating Mode (Voltage or Current)................................................................................... 3-20
3.5.3 Programming Voltage or Current and Associated Protect Limits...................................................... 3-20
3.5.4 Programming Associated Protect Limits........................................................................................... 3-21
3.5.4.1 When Operating in Voltage Mode............................................................................................... 3-21
3.5.4.2 When Operating in Current Mode ............................................................................................... 3-21
3.5.5 Programming Techniques to Optimize performance ........................................................................ 3-22
3.5.5.1 Programming Voltage/Current Limit and Current/Voltage Limit.................................................. 3-22
3.5.5.2 Making Sure the Previous Command is Complete ..................................................................... 3-22
3.5.6 Storing/Recalling Power Supply Output Settings.............................................................................. 3-23
3.5.7 Waveform Generation....................................................................................................................... 3-24
3.5.7.1 Waveform Overview.................................................................................................................... 3-24
3.5.7.2 Understanding How Waveforms Are Generated......................................................................... 3-25
3.5.7.3 Waveform Specifications............................................................................................................. 3-26
3.5.7.4 Executing a Waveform................................................................................................................ 3-26
3.5.7.5 Using Segments to Build a Waveform ........................................................................................ 3-27
3.5.8 Reset................................................................................................................................................. 3-28
3.5.9 Error Message Explanations............................................................................................................. 3-29
3.6 Programming Using Digital Control ........................................................................................................ 3-29
3.6.1 BIT 4882 Compatibility...................................................................................................................... 3-30
3.6.2 BIT 4886 Compatibility...................................................................................................................... 3-30
3.6.3 IEEE 488 (GPIB) Bus Protocol ......................................................................................................... 3-30
3.6.3.1 GPIB Port Setup.......................................................................................................................... 3-31

BOP-1K 111315 iii
TABLE OF CONTENTS
SECTION PAGE
3.6.3.1.1 Changing the GPIB Address...................................................................................................3-31
3.6.3.1.2 Configure Device Clear (DCL) Control....................................................................................3-32
3.6.3.1.3 Determining Whether *RST Command sets the Output Off or On..........................................3-32
3.6.4 RS232-C Operation........................................................................................................................... 3-32
3.6.4.1 Serial Interface............................................................................................................................. 3-32
3.6.4.2 RS 232 Implementation ............................................................................................................... 3-32
3.6.4.2.1 XON XOFF Method.................................................................................................................3-34
3.6.4.2.2 Echo Mode..............................................................................................................................3-34
3.6.4.2.3 Prompt Method........................................................................................................................3-35
3.6.4.3 RS 232 Serial Port Setup............................................................................................................. 3-35
3.6.4.3.1 Select Baud Rate....................................................................................................................3-35
3.6.4.3.2 Configure Echo Protocol.........................................................................................................3-35
3.6.4.3.3 Configure XON/XOFF Protocol...............................................................................................3-35
3.6.4.3.4 Configure Prompt Mode..........................................................................................................3-36
3.6.5 BOP VISA Instrument driver.............................................................................................................. 3-36
3.7 SCPI Programming ................................................................................................................................. 3-36
3.7.1 SCPI Messages................................................................................................................................. 3-37
3.7.2 Common Commands/Queries........................................................................................................... 3-37
3.7.3 SCPI Subsystem Command/Query Structure.................................................................................... 3-37
3.7.3.1 ABORt Subsystem....................................................................................................................... 3-37
3.7.3.2 INITiate Subsystem...................................................................................................................... 3-37
3.7.3.3 LIST Subsystem........................................................................................................................... 3-37
3.7.3.3.1 Required LIST Commands......................................................................................................3-38
3.7.3.3.2 Other Required Commands....................................................................................................3-39
3.7.3.3.3 Other Useful Commands.........................................................................................................3-39
3.7.3.3.4 Optional Commands ...............................................................................................................3-39
3.7.3.4 MEASure Subsystem................................................................................................................... 3-39
3.7.3.5 OUTPut Subsystem..................................................................................................................... 3-39
3.7.3.6 MEMory Subsystem..................................................................................................................... 3-40
3.7.3.7 STATus Subsystem..................................................................................................................... 3-42
3.7.3.8 TRIGger subsystem..................................................................................................................... 3-42
3.7.3.9 [SOURce:]VOLTage and [SOURce:]CURRent Subsystems....................................................... 3-42
3.7.3.10 CALibrate Subsystem.................................................................................................................. 3-43
3.7.3.11 System Subsystem...................................................................................................................... 3-43
3.7.3.11.1 Forgotten Passwords..............................................................................................................3-43
3.7.4 Program Message Structure.............................................................................................................. 3-44
3.7.4.1 Keyword....................................................................................................................................... 3-44
3.7.4.2 Keyword Separator...................................................................................................................... 3-44
3.7.4.3 Query Indicator ............................................................................................................................ 3-45
3.7.4.4 Data ............................................................................................................................................. 3-45
3.7.4.5 Data Separator............................................................................................................................. 3-45
3.7.4.6 Message Unit Separator.............................................................................................................. 3-45
3.7.4.7 Root Specifier .............................................................................................................................. 3-45
3.7.4.8 Message Terminator.................................................................................................................... 3-46
3.7.5 Understanding The Command Structure........................................................................................... 3-46
3.7.6 Program Message Syntax Summary................................................................................................. 3-47
3.7.7 Status Reporting................................................................................................................................ 3-47
3.7.7.1 Status Reporting Structure........................................................................................................... 3-47
3.7.7.2 Operational Status Register......................................................................................................... 3-49
3.7.7.3 QUEStionable Status Register..................................................................................................... 3-49
3.7.8 SCPI Program Examples................................................................................................................... 3-50

iv BOP-1K 111315
TABLE OF CONTENTS
SECTION PAGE
3.8 Operator Troubleshooting....................................................................................................................... 3-50
SECTION 4 - CALIBRATION
4.1 General................................................................................................................................................... 4-1
4.2 Test Equipment Requirements............................................................................................................... 4-3
4.3 Calibration using Remote SCPI commands via GPIB or RS 232 Interface............................................ 4-3
4.3.1 Calibration Procedure using SCPI Commands................................................................................. 4-5
4.3.2 Calibration of Series- or Parallel-Connected Units ........................................................................... 4-10
4.4 Calibration Storage................................................................................................................................. 4-10
APPENDIX A - SCPI COMMON COMMAND/QUERY DEFINITIONS
A.2 *CLS — Clear Status Command ............................................................................................................ A-1
A.3 *ESE — Standard Event Status Enable Command................................................................................ A-1
A.4 *ESE? — Standard Event Status Enable Query..................................................................................... A-2
A.5 *ESR? — Event Status Register Query.................................................................................................. A-2
A.6 *IDN? — Identification Query.................................................................................................................. A-2
A.7 *OPC — Operation Complete Command............................................................................................... A-2
A.8 *OPC? — Operation Complete Query.................................................................................................... A-3
A.9 *OPT? — Options Query........................................................................................................................ A-4
A.10 *RCL — Recall Command...................................................................................................................... A-4
A.11 *RST — Reset Command....................................................................................................................... A-4
A.12 *SAV — Save Command........................................................................................................................ A-4
A.13 *SRE — Service Request Enable Command......................................................................................... A-5
A.14 *SRE? — Service Request Enable Query.............................................................................................. A-5
A.15 *STB? — Status Byte Register Query.................................................................................................... A-5
A.16 *TRG — Trigger Command.................................................................................................................... A-5
A.17 *TST? — Self Test Query....................................................................................................................... A-6
A.18 *WAI — Wait-To-Continue Command.................................................................................................... A-6
APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS
B.1 Introduction............................................................................................................................................. B-1
B.2 Numerical Values.................................................................................................................................... B-2
B.3 ABORtCommand................................................................................................................................... B-2
B.4 CAL Commands and Queries................................................................................................................. B-2
B.5 INITiate[:IMMediate] Command............................................................................................................ B-3
B.6 INITiate:CONTinuous Command.......................................................................................................... B-4
B.7 INITiate:CONTinuous Query................................................................................................................. B-4
B.8 MEASure[:SCALar]:CURRent[:DC]? Query.......................................................................................... B-4
B.9 MEASure[:SCALar]:MODE[:DC] Command.......................................................................................... B-4
B.10 MEASure[:SCALar]:VOLTage[:DC]? Query.......................................................................................... B-4
B.11 MEASure[:SCALar]:TRANsient[:DC]? QUERY..................................................................................... B-4
B.12 MEMory:UPDate Command.................................................................................................................. B-5
B.13 OUTPut[:STATe]Command................................................................................................................... B-6
B.14 OUTPut[:STATe]Query ......................................................................................................................... B-7
B.15 OUTPut:CONTrol Command ................................................................................................................. B-7
B.16 OUTPut:CONT? Query .......................................................................................................................... B-7
B.17 OUTPut:MODE Command..................................................................................................................... B-7
B.18 OUTPut:MODE? Query.......................................................................................................................... B-7
B.19 [SOURce:]CURRent[:LEVel][:IMMediate][:AMPlitude]Command....................................................... B-7
B.20 [SOURce:]CURRent[:LEVel][:IMMediate][:AMPlitude] Query ............................................................. B-8
B.21 [SOURce:]CURRent[:LEVel]:LIMit[:BOTH] Command.......................................................................... B-8
B.22 [SOURce:]CURRent[:LEVel]:LIMit[:BOTH]? Query............................................................................... B-9
B.23 [SOURce:]CURRent[:LEVel]:LIMit:NEG Command.............................................................................. B-9

BOP-1K 111315 v
TABLE OF CONTENTS
SECTION PAGE
B.24 [SOURce:]CURRent[:LEVel]:LIMit:NEG? Query................................................................................... B-9
B.25 [SOURce:]CURRent[:LEVel]:LIMit:POS Command.............................................................................. B-9
B.26 [SOURce:]CURRent[:LEVel]:LIMit:POS? Query................................................................................... B-9
B.27 [SOURce:]CURRent:MODE Command................................................................................................. B-10
B.28 [SOURce:]CURRent:MODe? Query...................................................................................................... B-10
B.29 [SOURce:]CURRent[:LEVel]:PROTect[:BOTH] Command................................................................... B-10
B.30 [SOURce:]CURRent[:LEVel]:PROTect[:BOTH] Query.......................................................................... B-10
B.31 [SOURce:]CURRent[:LEVel]:PROTect:MODE Command.................................................................... B-11
B.32 [SOURce:]CURRent[:LEVel]:PROTect:MODE? Query......................................................................... B-11
B.33 [SOURce:]CURRent[:LEVel]:PROTect:NeGative Command............................................................... B-11
B.34 [SOURce:]CURRent[:LEVel]:PROTect:NeGative? Query.................................................................... B-11
B.35 [SOURce:]CURRent[:LEVel]:PROTect:POSitive Command................................................................ B-11
B.36 [SOURce:]CURRent[:LEVel]:PROTect:POSitive?Query..................................................................... B-11
B.37 [SOURce:]CURRent[:LEVel]:PROTect:LIMit[:BOTH] Command.......................................................... B-11
B.38 [SOURce:]CURRent[:LEVel]:PROTect:LIMit[:BOTH]? Query............................................................... B-12
B.39 [SOURce:]CURRent[:LEVel]:PROTect:LIMit:NeGative Command...................................................... B-12
B.40 [SOURce:]CURRent[:LEVel]:PROTect:LIMit:NeGative? Query........................................................... B-12
B.41 [SOURce:]CURRent[:LEVel]:PROTect:LIMit:POSitive Command....................................................... B-12
B.42 [SOURce:]CURRent[:LEVel]:PROTect:LIMit:POSitive? Query............................................................ B-12
B.43 [SOURce:]CURRent[:LEVel]:TRIGgered[:AMPlitude] Command ....................................................... B-12
B.44 [SOURce:]CURRent[:LEVel]:TRIGgered[:AMPlitude]? Query............................................................ B-13
B.45 [SOURce:]FUNCtion:MODE Command................................................................................................ B-13
B.46 [SOURce:]FUNCtion:MODE? Query..................................................................................................... B-13
B.47 [SOURce:]FUNCtion:MODE:TRIGger Command................................................................................. B-13
B.48 [SOURce:]FUNCtion:MODE:TRIGger? Query ..................................................................................... B-13
B.49 [SOURce:]LIST:CLEar Command......................................................................................................... B-13
B.50 [SOURce:]LIST:COUNt Command........................................................................................................ B-13
B.51 [SOURce:]LIST:COUNt? Query............................................................................................................. B-13
B.52 [SOURce:]LIST:COUNt:SKIP Command............................................................................................... B-14
B.53 [SOURce:]LIST:COUNt:SKIP? Query.................................................................................................... B-15
B.54 [SOURce:]LIST:CURRent Command.................................................................................................... B-15
B.55 [SOURce:]LIST:CURRent? Query......................................................................................................... B-16
B.56 [SOURce:]LIST:CURR:APPLyCommand............................................................................................. B-16
B.57 [SOURce:]LIST:CURRent:APPLy:SWEep Command.......................................................................... B-16
B.58 [SOURce:]LIST:CURRent:APPLy:SWEep?Query............................................................................... B-16
B.59 [SOURce:]LIST:CURRent:POINts? Query............................................................................................ B-16
B.60 [SOURce:]LIST:DWELlCommand ........................................................................................................ B-17
B.61 [SOURce:]LIST:DWELl? Query............................................................................................................. B-17
B.62 [SOURce:]LIST:DWELl:POINts? Query ................................................................................................ B-17
B.63 [SOURce:]LIST:QUERyCommand ....................................................................................................... B-17
B.64 [SOURce:]LIST:QUERy? Query............................................................................................................ B-17
B.65 [SOURce:]LIST:REPeat Command....................................................................................................... B-18
B.66 [SOURce:]LIST:RESolution? Query..................................................................................................... B-18
B.67 [SOURce:]LIST:SAMPle:CURRent Command ..................................................................................... B-18
B.68 [SOURce:]LIST:SAMPle:VOLTage Command...................................................................................... B-19
B.69 [SOURce:]LIST:SAMPle? Query........................................................................................................... B-19
B.70 [SOURce:]LIST:SET:SAMPle Command .............................................................................................. B-19
B.71 [SOURce:]LIST:SET:SAMPle? Query................................................................................................... B-19
B.72 [SOURce:]LIST:SET:TRIGger Command ............................................................................................. B-19
B.73 [SOURce:]LIST:SET:TRIGger? QUERY............................................................................................... B-20
B.74 [SOURce:]LIST:SET:WAIT Command................................................................................................... B-20
B.75 [SOURce:]LIST:SET:WAIT? QUERY .................................................................................................... B-20
B.76 [SOURce:]LIST:TRIGger Command..................................................................................................... B-20
B.77 [SOURce:]LIST:VOLTage Command.................................................................................................... B-20
B.78 [SOURce:]LIST:VOLTage? Query......................................................................................................... B-20
B.79 [SOURce:]LIST:VOLT:APPLyCommand .............................................................................................. B-24
B.80 [SOURce:]LIST:VOLTage:APPLy:SWEep Command .......................................................................... B-24

vi BOP-1K 111315
TABLE OF CONTENTS
SECTION PAGE
B.81 [SOURce:]LIST:VOLTage:APPLy:SWEep? Query ............................................................................... B-24
B.82 [SOURce:]LIST:VOLTage:POINts? Query............................................................................................ B-24
B.83 [SOURce:]LIST:WAIT:HIGH Command................................................................................................. B-25
B.84 [SOURce:]LIST:WAIT:LEDGe Command.............................................................................................. B-25
B.85 [SOURce:]LIST:WAIT:LOW Command.................................................................................................. B-25
B.86 [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude] Command....................................................... B-26
B.87 [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude]? Query............................................................ B-27
B.88 [SOURce:]VOLTage[:LEVel]:LIMit[:BOTH] Command .......................................................................... B-27
B.89 [SOURce:]VOLTage[:LEVel]:LIMit[:BOTH]? Query............................................................................... B-27
B.90 [SOURce:]VOLTage[:LEVel]:LIMit:NEGative Command...................................................................... B-27
B.91 [SOURce:]VOLTage[:LEVel]:LIMit:NEGative? Query........................................................................... B-27
B.92 [SOURce:]VOLTage[:LEVel]:LIMit:positive Command ......................................................................... B-27
B.93 [SOURce:]VOLTage[:LEVel]:LIMit:positive? Query.............................................................................. B-27
B.94 [SOURce:]VOLTage:MODe Command.................................................................................................. B-28
B.95 [SOURce:]VOLTage:MODE? Query...................................................................................................... B-28
B.96 [SOURce:]VOLTage[:LEVel]:PROTect:BOTH Command ..................................................................... B-28
B.97 [SOURce:]VOLTage[:LEVel]:PROTect[:BOTH]? Query........................................................................ B-29
B.98 [SOURce:]VOLTage[:LEVel]:PROTect:MODE Command..................................................................... B-29
B.99 [SOURce:]VOLTage[:LEVel]:PROTect:MODE? Query ......................................................................... B-29
B.100 [SOURce:]VOLTage[:LEVel]:PROTect:NeGative Command................................................................ B-29
B.101 [SOURce:]VOLTage[:LEVel]:PROTect:NeGative? Query .................................................................... B-29
B.102 [SOURce:]VOLTage[:LEVel]:PROTect:POSitive Command................................................................. B-30
B.103 [SOURce:]VOLTage[:LEVel]:PROTect:POSitive? Query ..................................................................... B-30
B.104 [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:BOTH Command ............................................................ B-30
B.105 [SOURce:]VOLTage[:LEVel]:PROTect:LIMit[:BOTH]? Query............................................................... B-30
B.106 [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:NeGative Command....................................................... B-30
B.107 [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:NeGative? Query ........................................................... B-30
B.108 [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:POSitive Command........................................................ B-31
B.109 [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:POSitive? Query ............................................................ B-31
B.110 [SOURce:]VOLTage[:LEVel]:TRIGgered[:AMPlitude] Command........................................................ B-31
B.111 [SOURce:]VOLTage[:LEVel]:TRIGgered[:AMPlitude]? Query............................................................. B-31
B.112 STATus:OPERation:CONDition? Query............................................................................................... B-31
B.113 STATus:OPERation:ENABle Command............................................................................................... B-32
B.114 STATus:OPERation:ENABle? Query.................................................................................................... B-32
B.115 STATus:OPERation[:EVENt] Query...................................................................................................... B-32
B.116 STATus:PRESet Command................................................................................................................... B-32
B.117 STATus:QUEStionable[:EVENt]? Query............................................................................................... B-32
B.118 STATus:QUEStionable:CONDition? Query.......................................................................................... B-32
B.119 STATus:QUEStionable:ENABle Command.......................................................................................... B-33
B.120 STATus:questionable:ENABle? Query................................................................................................ B-34
B.121 SYSTem:BEEP Command..................................................................................................................... B-34
B.122 SYSTem:COMMunication:GPIB:ADDRess Command........................................................................ B-34
B.123 SYSTem:COMMunication:GPIB:ADDRess? Query............................................................................. B-34
B.124 SYSTem:COMMunication:SERial:BAUD Command ............................................................................ B-34
B.125 SYSTem:COMMunication:SERial:BAUD? Query................................................................................. B-34
B.126 SYSTem:COMMunication:SERial:ECHO Command............................................................................ B-34
B.127 SYSTem:COMMunication:SERial:ECHO? Query .................................................................................. B-34
B.128 SYSTem:COMMunication:SERial:PACE Command.............................................................................. B-35
B.129 SYSTem:COMMunication:SERial:PACE? Query................................................................................... B-35
B.130 SYSTem:COMMunication:SERial:PROMpt CommanD.......................................................................... B-35
B.131 SYSTem:COMMunication:SERial:PROMpt? Query............................................................................... B-35
B.132 SYSTem:ERRor? Query ........................................................................................................................ B-35
B.133 SYSTem:ERRor:CODE? Query............................................................................................................. B-35
B.134 SYSTem:ERRor:CODE:ALL? Query...................................................................................................... B-35
B.135 SYSTem:KEYBoard Command............................................................................................................. B-35
B.136 SYSTem:KEYBoard? Query.................................................................................................................. B-36
B.137 SYSTem:PASSword:CENable Command ............................................................................................ B-36

BOP-1K 111315 vii
TABLE OF CONTENTS
SECTION PAGE
B.138 SYSTem:PASSword:CDISable Command........................................................................................... B-36
B.139 SYSTem:PASSword:NEW Command................................................................................................... B-36
B.140 SYSTem:PASSword:STATe? Query..................................................................................................... B-36
B.141 SYSTem:REMote Command................................................................................................................. B-36
B.142 SYSTem:REMote?Query...................................................................................................................... B-36
B.143 SYSTem:SECurity:IMMediate Command............................................................................................. B-37
B.144 SYSTem:SET Command ....................................................................................................................... B-37
B.145 SYSTem:SET? Query............................................................................................................................ B-37
B.146 SYSTem:VERSion? Query.................................................................................................................... B-37
B.147 TRIGger:SOURce Command................................................................................................................ B-38
B.148 TRIGger:SOURce? Query..................................................................................................................... B-38

LIST OF FIGURES
FIGURE TITLE PAGE
viii BOP-1K 111315
1-1 High Power BOP-GL Series Power Supply................................................................................................... x
1-2 BOP-GL Power Supply, Outline Drawing................................................................................................... 1-11
1-3 BOP Output Characteristics....................................................................................................................... 1-16
2-1 BOP-GL Series Rear Panel........................................................................................................................ 2-1
2-2 BOP-GL Top Cover Accessible Components ............................................................................................ 2-3
2-3 Factory Default Power-up Switch Settings................................................................................................. 2-10
2-4 Load Connections, Local Sensing.............................................................................................................. 2-16
2-5 Load Connections, Remote Sensing.......................................................................................................... 2-16
2-6 Connections for Analog Control and Monitoring of BOP-GL Power Supply............................................... 2-18
2-7 Parallel Configuration, Local Sensing, Typical........................................................................................... 2-20
2-8 Parallel Configuration, Remote Sensing, Typical....................................................................................... 2-21
2-9 Series Configuration, Local Sensing, Typical............................................................................................. 2-22
2-10 Series Configuration, Remote Sensing, Typical......................................................................................... 2-23
2-11 Typical Master/Slave Protection Interconnections ..................................................................................... 2-24
3-1 BOP-GL Series Front Panel....................................................................................................................... 3-3
3-2 Remote Shutdown Using External Power, Standalone or Multiple units.................................................... 3-13
3-3 Remote Shutdown Using Internal Power, Standalone Units...................................................................... 3-13
3-4 Remote Shutdown Using Internal Power, Multiple Units,........................................................................... 3-13
3-5 Remote On-Off, Standalone or Multiple Units............................................................................................ 3-14
3-6 Programming Example to Verify Previous Command has Completed....................................................... 3-24
3-7 Sample Waveform...................................................................................................................................... 3-26
3-8 RS 232 Implementation.............................................................................................................................. 3-33
3-9 Tree Diagram of SCPI Commands Used with BOP Power Supply............................................................ 3-41
3-10 Message Structure..................................................................................................................................... 3-45
3-11 Status Reporting Structure......................................................................................................................... 3-48
3-12 Typical Example Of BOP Power Supply Program Using SCPI Commands............................................... 3-51
4-1 Calibration Setup in Voltage Mode............................................................................................................. 4-5
4-2 Calibration Setup in Current Mode............................................................................................................. 4-8
A-1 GPIB Commands ....................................................................................................................................... A-3
B-1 Programming the Output............................................................................................................................ B-3
B-2 Using List Commands to measure sample at End of Pulse....................................................................... B-5
B-3 Using List Commands to measure sample at Start of Pulse...................................................................... B-6
B-4 Setting Limits.............................................................................................................................................. B-8
B-5 Using LIST Commands and Queries.......................................................................................................... B-14
B-6 Using LIST Commands for Sawtooth and Triangle Waveforms................................................................. B-21
B-7 Using List:WAIT Commands to Control Generation of a Waveform Measured by
Multiple External Devices using a Single External Pulse ........................................................................ B-22
B-8 Using List:WAIT Commands to allow an external device time to
function while imposing a maximum wait time......................................................................................... B-23
B-9 Using List:WAIT Commands to Control Generation of a Waveform Measured by
Multiple External Devices using the Low-Going leading Edge of an External Pulse............................... B-26
B-10 Using PROT:LIM:POS and PROT:LIM:POS Commands to Set Asymmetrical Limits............................... B-29
B-11 Using Status Commands and Queries....................................................................................................... B-33
B-12 Setting the Unit to Remote Mode via Serial (RS 232) Port ........................................................................ B-36
B-13 Using System Commands and Queries..................................................................................................... B-37

BOP-1K 111315 ix
LIST OF TABLES
TABLE TITLE PAGE
1-1 BOP-GL 1000 Watt Model Parameters .......................................................................................................1-1
1-2 BOP General Specifications .......................................................................................................................1-2
1-3 Equipment Supplied ....................................................................................................................................1-15
1-4 Safety Symbols ...........................................................................................................................................1-15
1-5 Accessories .................................................................................................................................................1-17
2-1 Rear Panel Connector Functions ................................................................................................................2-2
2-2 Power-Up Setup Switches ..........................................................................................................................2-3
2-3 Top Cover Calibration Adjustments ............................................................................................................2-4
2-4 IEEE 1118 Connector Input/Output Pin Assignments .................................................................................2-4
2-5 Trigger Port Pin Assignments .....................................................................................................................2-5
2-6 External Protection Connector Input/Output Pin Assignments ....................................................................2-5
2-7 RS232C PORT Input/Output Pin Assignments ...........................................................................................2-6
2-8 Parallel/Serial Control Out Port Pin Assignments .......................................................................................2-6
2-9 Parallel/Serial Control In Port Pin Assignments ..........................................................................................2-6
2-10 Parallel/Serial Protect In Port Pin Assignments ..........................................................................................2-7
2-11 Parallel/Serial Protect Out Port Pin Assignments .......................................................................................2-7
2-12 Analog I/O Port Input/Output Pin Assignments ...........................................................................................2-8
2-13 IEEE 488 Port Input/Output Pin Assignments .............................................................................................2-9
3-1 Front Panel Controls and Indicators ...........................................................................................................3-3
3-2 Voltage and Current Parameter Definitions ................................................................................................3-6
3-3 Power Supply Behavior when Output is set to OFF ....................................................................................3-10
3-4 Sine, Triangle and Ramp Waveform Frequency vs. Points ........................................................................3-25
3-5 Square Waveform Frequency vs. Points ....................................................................................................3-26
3-6 Waveform Segment Details ........................................................................................................................3-27
3-7 Operation of #RST Command ....................................................................................................................3-29
3-8 IEEE 488 (GPIB) Bus Interface Functions ..................................................................................................3-30
3-9 IEEE 488 (GPIB) Bus Command Mode Messages .....................................................................................3-31
3-10 IEEE 488 (GPIB) Bus Data Mode Messages ..............................................................................................3-31
3-11 Rules Governing Shortform Keywords ........................................................................................................3-44
4-1 Calibration Summary ..................................................................................................................................4-1
4-2 Suggested Sense Resistors ........................................................................................................................4-3
4-3 Voltage Calibration Measurements and Tolerances ...................................................................................4-3
4-4 Current Calibration Measurements and Tolerances ...................................................................................4-4
4-5 Calibration Storage .....................................................................................................................................4-11
A-1 IEEE 488.2 Command/query Index ...........................................................................................................A-1
A-2 Standard Event Status Enable Register and Standard Event Status Register Bits ...................................A-1
A-3 Service Request Enable and Status Byte Register Bits .............................................................................A-5
A-4 Built-in test Error Codes .............................................................................................................................A-6
B-1 SCPI Subsystem Command/query Index ..................................................................................................B-1
B-2 List Data Table ...........................................................................................................................................B-16
B-3 Operation Condition Register, Operation Enable Register,
and Operation Event Register Bits ..........................................................................................................B-31
B-4 Questionable Event Register, Questionable Condition Register
and Questionable Condition Enable Register Bits ..................................................................................B-32
B-5 Error Messages ..........................................................................................................................................B-38

xBOP-1K 111315
FIGURE 1-1. HIGH POWER BOP-GL SERIES POWER SUPPLY