Kero-sun Lc-56 User manual

LC-55 (Type A)

Fan Heater Inverter

Laser Clean

INSTRUCTIONS’ MANUAL

ΕΓΧΕΙΡΙΔΙΟ ΧΡΗΣΗΣ

LC-56

EN INSTRUCTIONS’ MANUAL

GR ΕΓΧΕΙΡΙΔΙΟΧΡΗΣΗΣ

This product is not suitable for primary heating purpose.

Το προϊόν αυτό δεν είναι κατάλληλο για σκοπούς πρωτογενούς θέρμανσης.

ENGLISH

SPECIFICATIONS

PART NAME

OPERATION

EMERGENCYMESSAGE

ROUTINE MAINTENANCE

TROUBLESHOOTING

LONG TERM STORAGE

________________________ 3

___________________________________3

_______________________________________3

_______________________________________7

___________________________14

__________________________15

______________________________16

_____________________________17

_______________________ 16

_________________________16

_____________________________16

______________________________________20

________________________25

______________________________________26

___________________________27

___________________________________28

IMPORTANT

READ AND UNDERSTAND INSTRUCTIONS BEFORE USING HEATER.

RETAININSTRUCTIONS FORFUTURE REFERENCE.

ΠΡΟΣΟΧΗ

ΔΙΑΒΑΣΤΕ ΠΡΟΣΕΚΤΙΚΑ ΑΥΤΕΣ ΤΙΣ ΟΔΗΓΙΕΣ ΧΡΗΣΕΩΣ ΠΡΙΝ ΤΗΝ ΧΡΗΣΗ ΤΗΣ ΘΕΡΜΑΣΤΡΑΣ.

ΦΥΛΑΞΤΕ ΤΙΣ ΟΔΗΓΙΕΣ ΧΡΗΣΕΩΣ ΓΙΑ ΜΕΛΛΟΝΤΙΚΗ ΑΝΑΦΟΡΑ ΣΕ ΑΥΤΕΣ.

ΕΛΛΗΝΙΚ Α

ΤΕΧΝΙΚΑΧΑΡΑΚΤΗΡΙΣΤΙΚΑ

ΜΕΡΗΤΗΣ ΣΥΣΚΕΥΗΣ

ΛΕΙΤΟΥΡΓΙΑ

ΜΗΝΥΜΑ ΠΙΘΑΝΗΣΒΛΑΒΗΣ

ΣΥΝΤΗΡΗΣΗ

ΠΡΟΒΛΗΜΑΤΑ– ΛΥΣΕΙΣ

ΑΠΟΘΗΚΕΥΣΗ

SPECIFICATIONS

MODEL

HEAT RATING

FUEL TANK CAPACITY

BURNING TIME

DIMENSIONS(W xD xH)

WEIGHT

VOLTAGE / FREQUENCY

ELECTRICAL CONSUMPTION

LC-55 (Type A)

17,100 BTU / 5.0 kW

5,300 BTU / 1.56 kW

7.6 lit.

15.7~ 50.0 hrs.

13.5 kg

230V AC, 50 Hz

Igniter : 320 W

Continuous : 23 W

High

Low

* Matching Room Size to HEAT RATING

• Because the “Heat Load” of an area to be

heated is influenced by so many factors, it is

impossible to specify a heater output to an

exact room size.

•If you use a heater too large for the area to be

heated, the temperature you desire will be

reached quickly. In such cases, to avoid

overheating the area, the heater must be turned

off frequently, or doors opened to other areas

of the house, or windows to the outside

opened to cool the area.

•If you use a heater too small for the area to be

heated, it will take much longer to reach the

desired temperature, in fact it may not be

reached at all depending on the outside

weather conditions.

PART NAME

BEFORE USING HEATER, FAMILIARIZE YOURSELF WITH THE FOLLOWING OPERATING

CONTROLS AND PART NAMES.

MAIN BODY

Front panel

Louver

operation panel

Removable fuel tank

Circulation

fan

Room

thermistor

Power supply

cord

Air filter

Carrying

handle

Top plate

550 x 327.5 x 445 mm

Front panel

Operation panel

Louver

Removable fuel tank

MODEL LC-56

HEAT RATING

GCV 5.0 kW

NCV 4.7 kW

FUEL TANK CAPACITY 7.6 lit.

BURNING TIME 15.7~50.0 hrs.

DIMENSIONS (W × D × H) 550 × 327.5 × 445 mm

WEIGHT 13.5 kg

VOLTAGE / FREQUENCY 230V AC, 50 Hz

ELECTRICAL CONSUMPTION

Igniter : 320 W

Continuous : 23 W

ENGLISH

OPERATION PANEL

ON/OFF Lamp —flashing : Preheating mode

constant : Heater in operation

key-lock Indicator —constant : Childproof Lock is on.

Temperature Indicator —constant : The Digital Indicator shows Set

temperature and Room temperature.

Clock Indicator —constant : The Digital Indicator shows current time.

Timer Lamp —constant : Heater in operation in timer mode.

Save Indicator —constant : The operation is in Save mode operation.

Ventilation Indicator —flashing : Oxygen level in room is insufficient.

Heater shuts off automatically.

Fuel Indicator —constant : Fuel tank empty. Only 10 minutes

burning time remaining. Digital indicator

shows the remaining burning time in minutes.

You can hear the alarm every 2minutes.

flashing : Heater extinguished due to lack of fuel.

(10 seconds alarm)

day/extension key —constant : Extend remaining burning time.

Altitude Indicator — constant : Altitude mode is on.

set room

Digital Indicator

Save Key

Day/

Extension

Key

Key-Lock

ON/OFF

Key/Lamp

Timer Key

Altitude Button

Adjustment Keys

ENGLISH

UNPACKING AND PLACEMENT

1. Take out heater from box carefully to avoid damage.

2. Remove all packing materials from heater.

3. Make sure all screws are tight and all parts intact.

NOTE: Save shipping carton and all packing materials for future storage of your heater.

4. When positioning your heater for use, keep it away from walls and all other materials as illustrated

below.

ENGLISH

UNPACKING AND PLACEMENT

1. Take out heater from box carefully to avoid damage.

2. Remove all packing materials from heater.

3. Make sure all screws are tight and all parts intact.

NOTE: Save shipping carton and all packing materials for future storage of your heater.

4. When positioning your heater for use, keep it away from walls and all other materials as illus-

trated below.

5. The floor should be firm and completely level. Reposition the heater, when it is not level.

NOTE: If your heater is not on a level surface, change its location. Do not attempt to prop heater

up with books or other objects.

50 cm

20 cm

150 cm

50 cm

5. The floor should be firm and completely level. Reposition the heater, when it is not level.

NOTE: If your heater is not on a level surface, change its location. Do not attempt to prop heater up

with books or other objects.

ENGLISH

FUELING

WARNING: Use only water-clear kerosene (parafn).

Never use gasoline or other ammable

liquids.

ALWAYS extinguish heater before rell

heater fuel tank.

Fuel heater outside the living area.

1. Open the fuel tank lid on the top of heater cabinet and lift out the re-

movable fuel tank. Turn the removable tank upside down and remove

the fuel tank cap.

2. Insert the straight tube of the manual siphon into the jerrycans; insert

the siphon’s exible hose into the removable fuel tank opening.

3. Turn the air vent knob on the top of the siphon clockwise to close the

vent. Start the ow of kerosene (parafn) by squeezing the bulb of the

siphon vigorously six or seven times. Once ow begins, it is no longer

necessary to squeeze the bulb.

4. Check the removable tank fuel gauge while lling the tank. Stop lling

by loosening the switch button on top of the pump (turn anti-clock-

wise), once the gauge indicates that the tank is full. Never overll the

tank, especially not when the fuel is very cold (fuel expands when it

heats up).

NOTE: Be careful to avoid overlling the tank, especially with very cold

kerosene (parafn). Overow might occur due to expansion when the

fuel warms up.

5. Remove the siphon carefully, allowing excess kerosene (parafn) to

drain from the tube back into the jerrycans. Replace fuel tank cap and

tighten it securely. Be sure to wipe away any spilled kerosene (paraf-

n) from tank and other heater parts.

6. After making sure fuel tank cap is tightly fastened, invert tank and re-

place into heater body.

ENGLISH

OPERATION

CAUTION : Always make sure that there is sufcient ventilation.

SET CLOCK

It is only possible to set the correct time, when the

heater is connected to the mains and not burning.

1. Use the Adjustment Keys ( hour / min.) to

set the time.

2. To set the time, press “hour” and “min.” set but-

tons. Individual motions will increase the time by

one unit; holding continuously will raise either the

“hour” or “min.” rapidly. After approximately 10

seconds the blinking will stop and the setting will

be locked. 5 Minutes after switching off the heater,

the information on the display will disappear and

the heater will automatically switch into the stand-

by position.

IGNITION

1. Just press the button to ignite the heater. The

button will start blinking, indicating that the ignition

procedure has started. This will take a short while.

2. After this time heater will automatically ignite and

The button will cease its ashing. The Operation

Lamp will remain alight so long as heater is burn-

ing.

NOTE: If using your heater for the rst time, or after long term storage, ignition may not take place

on the rst try. Press the button again.

NOTE: Fuel pump may produce an audible operating noise at ignition. This is only temporary.

SET CLOCK

It is only possible to set the correct time and day, when

the heater is connected to the mains and not burning.

Use the adjustment keys to set the time and extension/

day/set to set the day.

First press one of the three keys to switch

on the function (the 4-digit will start blinking).

Next, set the hours using the key (▼hour)

and the minutes using the key (▲min.) and

the day using the key extension/day/set .

Press once to increase the value by one step.

When you hold down the key, the value will continue going up, until you release

the key again. After approximately 10 seconds the 4-digit will stop blinking and the

setting will be locked. 5 minutes after switching off the heater, the information on

the display will disappear and the heater will automatically switch into the stand-by

position.

set room

1 2

ENGLISH

OPERATION

CAUTION : Always make sure that there is sufcient ventilation.

SET CLOCK

It is only possible to set the correct time, when the

heater is connected to the mains and not burning.

1. Use the Adjustment Keys ( hour / min.) to

set the time.

2. To set the time, press “hour” and “min.” set but-

tons. Individual motions will increase the time by

one unit; holding continuously will raise either the

“hour” or “min.” rapidly. After approximately 10

seconds the blinking will stop and the setting will

be locked. 5 Minutes after switching off the heater,

the information on the display will disappear and

the heater will automatically switch into the stand-

by position.

IGNITION

1. Just press the button to ignite the heater. The

button will start blinking, indicating that the ignition

procedure has started. This will take a short while.

2. After this time heater will automatically ignite and

The button will cease its ashing. The Operation

Lamp will remain alight so long as heater is burn-

ing.

NOTE: If using your heater for the rst time, or after long term storage, ignition may not take place

on the rst try. Press the button again.

NOTE: Fuel pump may produce an audible operating noise at ignition. This is only temporary.

set room

Just press the key to ignite the heater. ON/OFF

Lamp will start blinking, indicating that the ignition

procedure has started. This will take a short while.

After this time heater will automatically ignite and

ON/OFF Lamp will cease its flashing. ON/OFF

Lamp will remain alight so long as heater is burn-

ing.

NOTE: If using your heater for the first time, or after long term storage, ignition may not take place

on the first try. Press the key again.

NOTE: Fuel pump may produce an audible operating noise at ignition. This is only temporary.

ENGLISH

TEMPERATURE REGULATION

1. Use the Adjustment keys ( hour / min.) to adjust the temperature.

2. Adjust the temperature using the key on the right ( min.) to set the

temperature to a higher setting and the key on the left ( hour ) to

lower the temperature.

3. Until the room temperature has reached the set temperature, the

heater will burn at either high or medium burning mode. When the room temperature reaches

or slightly exceeds the set temperature, the heater will automatically shift to maintain the de-

sired temperature.

NOTE: The standard setting of the heater is 20°C. However, once the set temperature has been

changed the new setting will remain in effect unless changed.

NOTE: Room temperature measurements are taken directly behind the heater. These measure-

ments may not represent the true room temperature.

SAVE OPERATION

The “SAVE” function allows you to limit the temperature. When this

function is activated, the heater will automatically switch off, when the

room temperature exceeds the set temperarure by 3°C. Subsequently,

when the room temperature has dropped again to the set temperature,

the heater will automatically switch on again. Activate the “SAVE” set-

ting by pressing the Save key. The Save indicalor will light up. Switch off

the function by pressing the Save key once again.

NOTE: Without the “SAVE” setting your heater will maintain the set temperature by approximation

as well, by adjusting its heating capacity. “SAVE” is an economy setting, which you can use when,

for instance, you are not present in the room or to keep it frost-free.

set room

1 2

SAVE OPERATION

The “ Save” function allows you to limit the set temperature.

When pressing the “Save” key, the heater will shift to the

minimum burning mode regardless of the set temperature. The

“Save” mark will be shown in the display. To cancel the “Save”

function, press the “Save” key once again.

(hour

▼

/ min.

▲

)

(min.

▲

)

(hour

▼

)

ENGLISH

When the Fuel Indicator lights up, it means that there is only fuel left

for 10 more minutes. The count-down of the remaining heating time

can be seen in the Digital indicator. Now you have two options:

you remove the removable fuel tank and refill it outside the living

room or

you push the Extension key. By pushing this key, the remaining

heating time will extend to 60 minutes. The heater will automati-

cally switch back to its lowest position. In the display the number

60 will appear, which will decline to 10. At the arrival of 10, you will

hear an alarm signal every two minutes, warning you to refill the

removable tank. If you do not react, the heater will extinguish by itself. The heater will also sound

a warning signal, when it switches off. The Fuel Indicator will blink, while four lines (--:--) are

blinking in the Digital indicator. You can stop this by pressing the key once more.

ENGLISH

CHILDPROOF LOCK

VENTILATION INDICATOR

FUEL INDICATOR

Once the heater has used up all its fuel and extinguished, it will take some time, after the refill,

before the heater is completely ready for use again.

The childproof lock can be used to prevent children accidentally

changing the heater settings. When the heater is burning and the

childproof lock is on, the heater can only be switched off.Other

functions are blocked then. If the heater has already been

switched off, the childproof lock also prevents accidental ignition

of the heater.

Activate the childproof lock by pressing the Key-lock key and holding

it down for more 3 seconds.

The KEY-LOCK indicator will light up indicating that the childproof

lock has been activated.

Switch off the childproof lock by pressing the Key-lock key and

holding it down for more than 3 seconds once again.

When the VENT indicator starts blinking, this is a sign that the

room is not vented sufficiently. If you do not provide additional

ventilation, the heater will switch off automatically after some time.

If the indicator continues blinking after extraventilation, please

contact your dealer.

When the mark

appears, the childproof

lock has been activated.

When the FUEL indicator

has appeard, the informa-

tion display will show the

number of minutes of fuel

left in the tank.

ENGLISH

AUTOMATIC CLEANING MODE

When the heater has been burning continuously for two hours at its highest setting, the burner will

automatically start an autoclean procedure. The display will show the autocleaningcode

run-

ning back to . The procedure takes 5 minutes, during which the heater will burn at its lowest

setting, while the burner autocleans. When the burner is clean again, the heater will automatically

switch back tothe highest setting again.

TURNING OFF HEATER

Press the key. This will extinguish heater and ON/OFF Lamp on the indicator panel will go out.

down heater.

NEVER: Turn heater off by disconnecting the heater plug from the main elecrical supply.

DO NOT: Restart your heater for at least ten minutes.

AUTOMATIC DEACTIVATION

This heater is fitted with a safety system that ensures that it swiches off automatically after 50

hours continuous operation.

The following will then appear in the display: . If desired, you can switch the heater on again

by pressing the key.

The circulation fan motor will operate further, for approximately 150 seconds to assist in cooling

ENGLISH

AUTOMATIC CLEANING MODE

When the heater has been burning continuously for two hours at its highest setting, the burner will

automatically start an autoclean procedure. The display will show the autocleaningcode

run-

ning back to . The procedure takes 5 minutes, during which the heater will burn at its lowest

setting, while the burner autocleans. When the burner is clean again, the heater will automatically

switch back tothe highest setting again.

TURNING OFF HEATER

Press the key. This will extinguish heater and ON/OFF Lamp on the indicator panel will go out.

down heater.

NEVER: Turn heater off by disconnecting the heater plug from the main elecrical supply.

DO NOT: Restart your heater for at least ten minutes.

AUTOMATIC DEACTIVATION

This heater is fitted with a safety system that ensures that it swiches off automatically after 50

hours continuous operation.

The following will then appear in the display: . If desired, you can switch the heater on again

by pressing the key.

The circulation fan motor will operate further, for approximately 150 seconds to assist in cooling

ENGLISH

AUTOMATIC CLEANING MODE

When the heater has been burning continuously for two hours at its highest setting, the burner will

automatically start an autoclean procedure. The display will show the autocleaningcode

run-

ning back to . The procedure takes 5 minutes, during which the heater will burn at its lowest

setting, while the burner autocleans. When the burner is clean again, the heater will automatically

switch back tothe highest setting again.

TURNING OFF HEATER

Press the key. This will extinguish heater and ON/OFF Lamp on the indicator panel will go out.

down heater.

NEVER: Turn heater off by disconnecting the heater plug from the main elecrical supply.

DO NOT: Restart your heater for at least ten minutes.

AUTOMATIC DEACTIVATION

This heater is fitted with a safety system that ensures that it swiches off automatically after 50

hours continuous operation.

The following will then appear in the display: . If desired, you can switch the heater on again

by pressing the key.

The circulation fan motor will operate further, for approximately 150 seconds to assist in cooling

ENGLISH

AUTOMATIC CLEANING MODE

When the heater has been burning continuously for two hours at its highest setting, the burner will

automatically start an autoclean procedure. The display will show the autocleaningcode

run-

ning back to . The procedure takes 5 minutes, during which the heater will burn at its lowest

setting, while the burner autocleans. When the burner is clean again, the heater will automatically

switch back tothe highest setting again.

TURNING OFF HEATER

Press the key. This will extinguish heater and ON/OFF Lamp on the indicator panel will go out.

down heater.

NEVER: Turn heater off by disconnecting the heater plug from the main elecrical supply.

DO NOT: Restart your heater for at least ten minutes.

AUTOMATIC DEACTIVATION

This heater is fitted with a safety system that ensures that it swiches off automatically after 50

hours continuous operation.

The following will then appear in the display: . If desired, you can switch the heater on again

by pressing the key.

The circulation fan motor will operate further, for approximately 150 seconds to assist in cooling

ENGLISH

AUTOMATIC CLEANING MODE

When the heater has been burning continuously for two hours at its highest setting, the burner will

automatically start an autoclean procedure. The display will show the autocleaningcode

run-

ning back to . The procedure takes 5 minutes, during which the heater will burn at its lowest

setting, while the burner autocleans. When the burner is clean again, the heater will automatically

switch back tothe highest setting again.

TURNING OFF HEATER

Press the key. This will extinguish heater and ON/OFF Lamp on the indicator panel will go out.

down heater.

NEVER: Turn heater off by disconnecting the heater plug from the main elecrical supply.

DO NOT: Restart your heater for at least ten minutes.

AUTOMATIC DEACTIVATION

This heater is fitted with a safety system that ensures that it swiches off automatically after 50

hours continuous operation.

The following will then appear in the display: . If desired, you can switch the heater on again

by pressing the key.

The circulation fan motor will operate further, for approximately 150 seconds to assist in cooling

ENGLISH

AUTOMATIC CLEANING MODE

When the heater has been burning continuously for two hours at its highest setting, the burner will

automatically start an autoclean procedure. The display will show the autocleaningcode

run-

ning back to . The procedure takes 5 minutes, during which the heater will burn at its lowest

setting, while the burner autocleans. When the burner is clean again, the heater will automatically

switch back tothe highest setting again.

TURNING OFF HEATER

Press the key. This will extinguish heater and ON/OFF Lamp on the indicator panel will go out.

down heater.

NEVER: Turn heater off by disconnecting the heater plug from the main elecrical supply.

DO NOT: Restart your heater for at least ten minutes.

AUTOMATIC DEACTIVATION

This heater is fitted with a safety system that ensures that it swiches off automatically after 50

hours continuous operation.

The following will then appear in the display: . If desired, you can switch the heater on again

by pressing the key.

The circulation fan motor will operate further, for approximately 150 seconds to assist in cooling

ENGLISH

WEEKLY TIMER

Here is an example on how the weekly timer can be programmed:

• Maximum of 3 programs per day can be set.

• Every day of the week can be programmed separately.

• Minimum switching interval, 1 hour.

• Minimum activation time, 1 hour.

• Choice between manual and timer.

• Settings are saved in the memory and remain saved without power supply.

Monday Tuesday Wednesday Thursday Friday Saturday Sunday

P1 ON 6:30 6:30 6:30 6:30 6:30 10:00 9:00

P1 OFF 8:45 8:45 8:45 8:45 8:45 23:00 23:00

P2 ON 12:00 15:00 18:00 12:00 12:00

P2 OFF 14:00 23:00 23:00 14:00 14:00

P3 ON 18:00 18:00 18:00

P3 OFF 23:00 23:00 23:00

set room

Make sure the heater is connected to the mains and not burning.

Press the timer-key. Also make sure the time and day are set

correctly. Choose the day you would like to program by pressing the

adjustment keys. Press the adjustment key ▲to increase the day by

one step and press the key ▼to decrease the day.

Press extension/day/set to select the desired day. The display shows:

With the adjustment keys ▲and ▼you can choose between the

programs P1, P2 and P3. You can also choose the option Copy to

copying the setting from one day to another. Press extension/day/set

to select the displayed program.

Use the adjustment keys to set the hour at which the heater must

ignite. Press the adjusment key ▲to increase the hour and the key

▼to decrease the hour. Press extension/day/set to select the right

hour.

PROGRAMMING THE WEEKLY TIMER

ENGLISH

Then, use the adjustment keys to set the minute. Press the

adjustment key ▲to increase the minute and the key ▼to decrease

the minute. Press extension/day/set to select the right minute.

Use the adjustment keys to set the hour at which the heater must

shutt off.

Press the adjusment key ▲to increase the hour and the key ▼to

decrease the hour.

Press extension/day/set to select the right hour.

Then, use the adjustment keys to set the minute. Press the

adjustment key ▲to increase the minute and the key ▼to decrease

the minute. Press extension/day/set to select the right minute.

The settings for program 1 for Monday are programmed and the

display shows SET for 3 seconds.

After 3 seconds choose another day or end the setting mode by

pressing timer.

Press the “timer” key to exit the weekly timer setting mode and return

to the time and a day of the week display. Timer lamp turns off.

Use the copy function if there are multiple days during one week which should have the same

setting times.

Make sure that the heater is not burning. Press the timer key. Use

the adjustment keys until the day of its source is displayed in the

display.

Press extension/day/set to select.

The display shows:

COPYING THE SETTING FROM ONE DAY TO ANOTHER

ENGLISH

Use the adjustment keys ▲or ▼to choose copy. Press extension/day/set to

select the copy function.

Use the adjustment keys ▲or ▼to select the day to which the settings

should be copied. Press extension/day/set to choose the selected day.

The settings for program for Tuesday are programmed and the display shows

SET for 3 seconds.

After 3 seconds choose another day to copy or end the setting mode by

pressing timer.

Switch on the heater by pressing the (ON/OFF button). And then press the timer-key immediately after that.

The Timer light will light up and the heater shuts off. The On / Off indicators on the display shows whether the

appliance is switched on or off.

When the appliance is switched off by the timer, the off indicator is visible.

The display shows the -actual time.

When the appliance is switched on by the timer, the on indicator is visible.

The display shows the desired (set) and actual (room) temperature.

OPERATING THE WEEKLY TIMER

ENGLISH

AUTOMATIC CLEANING MODE

When the heater has been burning continuously for two hours at its highest setting, the burner will

automatically start an autoclean procedure. The display will show the autocleaningcode

run-

ning back to . The procedure takes 5 minutes, during which the heater will burn at its lowest

setting, while the burner autocleans. When the burner is clean again, the heater will automatically

switch back tothe highest setting again.

TURNING OFF HEATER

Press the key. This will extinguish heater and ON/OFF Lamp on the indicator panel will go out.

down heater.

NEVER: Turn heater off by disconnecting the heater plug from the main elecrical supply.

DO NOT: Restart your heater for at least ten minutes.

AUTOMATIC DEACTIVATION

This heater is fitted with a safety system that ensures that it swiches off automatically after 50

hours continuous operation.

The following will then appear in the display: . If desired, you can switch the heater on again

by pressing the key.

The circulation fan motor will operate further, for approximately 150 seconds to assist in cooling

ENGLISH

EMERGENCY MESSAGE

In the event that heater should extinguish itself, without any action or your part, you should look

to the digital indicator for any of the following messages.

MESSAGE

(Digital Indicator) MESSAGE MEANING WHAT TO DO

E-0

Temperature within the heater too

high. Cool-down and re-ignite.

F-0

Power interrupted. You can re-ignite the heater.

E-1

Thermostat is broken or

disconnected. Contact your dealer.

F-1

Faulty burner thermistor. Contact your dealer.

E-2

Primary flame rod is malfunctioning

and / or dirty. Contact your dealer.

E-23

Re-ignite the heater immediately

after extiguishing.

Wait for approx. 30 sec. and re-

ignite after inserting the plug again.

E-5

You have accidentally activated

your safety tip-over switch.

You should reset this device as

described, press the ‘’OFF’’ button

and restart your heater.

E-6

Burner flame has been

extinguished during operation.

Check to see if air filter is clogged

with dust. If so, clean air filter.

E-7

Room temperature above 32°C. Re-ignite the heater.

E-8

Failure of blower motor. Contact your dealer.

E-81

Abnormal frequency. Insert the

plug into the wall-socket again. Contact your dealer.

E-9

Air filter dirty; or Fuel pump dirty. Clean filter. / Contact your dealer.

50 Hr

The heater has been in operation

continuously for a period of 50 hours

and has turned itself off automatically.

Switch the heater.

--:--

Out of fuel. Refill removable tank.

--:--

Too little ventilation. Ventilate better.

ENGLISH

ROUTINE MAINTENANCE

CAUTION: Besure to unplug heater before performing any checks or cleaning.

CAUTION: Do not remove any parts from the heater except removable fuel tank, fuel acceptance

fitting and air filter.

WARNING: Allow heater tocool completely before cleaning or maintenance.

1. Clean Air Filter

Clean the air filter with a vacuum cleaner on a weekly basis.

If filter is clogged with dust or lint, smoking and improper combustion

may result.

NOTE: If filter was washed in water, dry thoroughly before replacing.

NOTE: Never wipe with cloth, it will clogfilters further.

2. Clean Fan Cover

Using a vacuum cleaner, remove any dust from the fan cover at the

back of the heater.

3. Clean Fuel Acceptance Fitting

When dirt or dust accumulates in the fuel acceptancefitting, it should

be cleaned, Check fuel acceptancetting each time your refuel.

4. Check for fuel leaks

Make it a habit to check for signs of fuel leakage. Wipe off any spilled

fuel on the sub tank and removable fuel tank.

Spilled fuel may cause odor or risk offire.

5. Clean Louvers

Dust and stains should be wiped off louvers with a damp cloth. If dust

and stains are allowed to build up over a period of time, removal will

become difficult. Make it a point to wipe clean regularly.

ENGLISH

TROUBLESHOOTING

Should problems arise during operation or ignition, use this chart to determine the cause and the

proper steps to take. Be sure to unplug heater and allow to cool completely before taking correc-

tive measures.

PROBLEM CAUSE SOLUTION

POWER LAMP FAILS

TO TURN ON

- Disconnected power plug

- Incorrect wiring

- Circuit board malfunction

- Plug into 230V AC outlet

- Consult your dealer

NO IGNITION - Out of fuel

- Clogged air  lter

- Use of inferior kerosene (paraf-

 n)

- Incorrect wiring

- Circuit board, ignition heater or

fuel pump malfunction

- Refuel

- Clean air  lter

- Remove fuel and refuel using

fresh, clear kerosene (para n)

- Consult your dealer

ODOR - Clogged air  lter

- Spilled kerosene (para n)

- Use of inferior kerosene (paraf-

 n)

- Clean air  lter

- Wipe o any kerosene (para n)

spills from fuel sub tank, remov-

able fuel tank and drip tray

- Remove fuel and refuel using

fresh, water-clear kerosene

(para n)

EXTINGUISHED

AFTER IGNITION

- Excessive room temperature

- Oxygen shortage in room

- Tip-over switch activated

- Water in fuel acceptance  tting

- Out of fuel

- Flame sensor or fuel pump

malfunction

- High limit switch activated

- Allow room to cool

- Open doors and windows to

ventilate room thoroughly

- Reignite

- Remove fuel and refuel using

fresh, water-clear kerosene

(para n)

- Refuel

- Consult your dealer

- Clean circulation fan cover,

remove any obstructions

POOR COMBUSTION/

NOISY COMBUSTION

- Clogged air  lter

- Loose screws or incorrect as-

sembly

- Incorrect wiring

- Circuit board or fuel pump

malfunction

- Altitude too high

- Clean air  lter.

- Consult your dealer.

If the corrective measures outlined above do not solve the problem, please consult your dealer.

Should problems arise during operation or ignition, use this chart to determine the cause and the

proper steps to take. Be sure to unplug heater and allow to cool completely before taking correc-

tive measures.

PROBLEM CAUSE SOLUTION

POWER LAMP FAILS

TO TURN ON

- Disconnected power plug

- Incorrect wiring

- Circuit board malfunction

- Plug into 230V AC outlet.

- Consult your dealer.

NO IGNITION - Out of fuel

- Clogged air lter

Use of inferior kerosene (paran)

- Incorrect wiring

- Circuit board, ignition heater

or fuel pump malfunction

- Refuel.

- Clean air lter.

- Remove fuel and refuel using

fresh, clear kerosene (paran).

- Consult your dealer.

ODOR - Clogged air lter

- Spilled kerosene (paran )

- Use of inferior kerosene (paraf-

n)

- Clean air lter.

Wipe o any kerosene (paran)

spills from fuel sub tank, remov-

able fuel tank and drip tray.

- Remove fuel and refuel using

fresh, water-clear kerosene

(paran).

POOR COMBUSTION/

NOISY COMBUSTION

(howling/

whistling sound)

- Clogged air lter

- Insucient ventilation

- Loose screws or incorrect as-

sembly

- Incorrect wiring

- Circuit board or fuel pump

malfunction

- Altitude too high

- Clean air lter.

- Open doors and windows to

ventilate room thoroughly.

- Consult your dealer.

EXTINGUISHED

AFTER IGNITION

- Excessive room temperature

- Oxygen shortage in room

- Tip-over switch activated

- Water in fuel acceptance tting

- Out of fuel

- Flame sensor or fuel pump

malfunction

- High limit switch activated

- Allow room to cool.

- Open doors and windows to

ventilate room thoroughly.

- Reignite.

- Remove fuel and refuel using

fresh, water-clear kerosene

(paran).

- Refuel.

- Consult your dealer.

- Clean circulation fan cover,

remove any obstructions.

ENGLISH

LONG TERM STORAGE

At the end of the heating season, you must store the heater in a dust-free plece, if possible in its

original packaging. The following procedures are recommended.

1. Drain Fuel Tank

Remove any kerosene (paraffin), dust or water remaining in the fuel sub

tank and removable fuel tank to prevent rusting.

2. Clean Heater

Wipe off any dirt or dust on heater with a damp cloth, then wipe again

using a dry cloth.

3. If your heater needs any service or repair, now is the time to call your

dealer to have it done before storage. That way, it will be ready for im-

mediate use when the next heating season begins.

4. Store Heater

The original shipping carton is the best plase to store your heater. If you

do not have the original packing materials, cover heater with a large

plastic bag and store in a dry place.

Fuel

acceptance

Fitting

Disposal of old Electrical & Electronic Equipment (Applicable in the European Union

and other European countries with separate collection systems).

This symbol on the product or on its packaging indicates that this product shall not be treated

as household waste. Instead it shall be handed over to the applicable collection point for the

recycling of electrical and electronic equipment. By ensuring this product is disposed of cor-

rectly, you will help prevent potential negative consequences for the environment and human

health, which could otherwise be caused by inappropriate waste handling of this product. The

recycling of materials will help to conserve natural resources. For more detailed information about recycling

of this product, please contact your local city office, your household waste disposal service or the shop

where you purchased the product.

Model LC-55 (Type A)

Imported by DELTA DOMESTIC APPLIANCES S.A.

6, Kifissou Av., Egaleo, P.C. 12242

Inverter Laser Clean Fan Heater

Package contains 1 piece

Product Dimension (HxWxD) mm: 445x550x327.5

Packing Dimension (HxWxD) mm : 500x600x370

Net / Gross Weight kg: 13,5 / 14,5

Country of Origin: JAPAN