Kettler 7199-200 User manual

KETTLER
CAVALIER OUTDOOR
FOOSBALL TABLE
Model 7199-200
Adult Assembly Required Made in Italy
Picture Similar
1 reqd.
KETTLER®
International Inc. • 1355 London Bridge Road • Virginia Beach, VA 23453 USA
www.kettlerusa.com
[e-mail]

All KETTLER® products are designed in accordance with the latest safety regulations and undergo a constant
process of quality control during manufacturing. The knowledge gained in this process is used to constantly improve
and develop our products. In order to offer our customers the very best in product quality, we reserve the right to
make technical changes at any time. In spite of this, should you have any cause for complaint, please contact
KETTLER®.
Before assembling or using the foosball table, please read the following instructions carefully. They contain
important information for use and maintenance of the equipment as well as for your personal safety. Keep
these instructions in a safe place for maintenance purposes or for ordering spare parts.
•
The foosball table should be used only for its
intended purpose, i.e. for playing with suitable
balls.
•All other uses are prohibited and may be
dangerous. The manufacturer cannot be held
liable for damage or injury caused be improper
use of the table.
•Damaged or worn components may endanger
your safety or shorten the lifespan of the foosball
table. Replace worn or damaged components
immediately and remove the table from use until
this has been done. Use only spare parts
manufactured by KETTLER®.
•The foosball table complies with all safety
regulations. Incorrect repairs, alterations to the
design (removal of original parts, addition of
other components etc.) may endanger the safety
of the user.
•Instruct other persons (in particular children)
using the table in its correct use, and draw their
attention to any potential source of danger,
especially when setting up or dismantling the
table.
•Caution: During assembly, keep all items out of
children’s reach (choking hazard-contains small
parts).
•Regularly check all screws, bolts etc. to ensure
they are in good condition.
•Warning: This is a heavy product. Do not
attempt to move or maneuver without
adequate help and safety measures. May result
in injury. Children should not move table.
•
Do not use the foosball table until it has been
fully and correctly assembled and checked.
•Set the table up on a level surface.
•When not playing or storing the table, always
use the included protective cover.
•Do not use corrosive or abrasive materials to
clean the equipment. Ensure that such
materials are not allowed to pollute the
environment. In most cases a damp cloth is
sufficient.
•
Waste disposal: KETTLER® products are
recyclable. At the end of its useful life, please
dispose of correctly and safely complying with
your local facilities and guidelines.
•Once the table is assembled it may not fit
through your doorways. For this reason you
should assemble the table where you intend to
use the table. Should you wish to move the
table some disassembly may be required.
1

Number Included-1 Number Included-2
Number Included-8
Number Included-1
Number Included-2Number Included-5
Number
Included-2
2

Number Included-2
Number Included-4
Number Included-8
Number Included-6
(M2.8 X 11.5 Screw)
Number Included-44
(M4 X 25 Screw)
Number Included-
10 Blue
10 Silver
Number Included-
2 Blue
2 Silver
Number Included-8
Number Included-8
Number
Included-8
(M8x40 Carriage Bolt)
Number Included-8
Number Included-4
(M3.9X35 Screw)
Number Included-
1 Set Blue
1 Set Silver
Number Included-8
(M8 Lockwasher)
Number Included-8
(M8 Hexnut)
3
May come
assembled as
one piece or
separately as
two pieces.

Step 1
Leg Assembly
1 required
1 required
Place legs inside cabinet at an
outward angle. Horizontal bar
between legs should be
toward table end. (A)
Ensure holes in side of cabinet
align with holes in leg. Insert
two M8 x 40 Carriage Bolts
from the outside in towards
leg. (B)
Using hammer, lightly tap bolt
heads into side (C), ensuring
they are flush with cabinet (D).
4
2 each required 1 required

Step 1 (continued)
REPEAT STEP 1 A-G FOR EACH LEG
Step 2
Setting the table upright
From inside of cabinet, place M8
Lockwashers then M8 hexnuts
onto Carriage Bolt ends (E) and
tighten (F).
Screw floor leveler into leg post. (G)
Turn the table onto its feet to
prepare for the next assembly
step.
Warning: This is a heavy product.
Do not attempt to move or
maneuver without adequate help
and safety measures. May result in
injury.
5
IMPORTANT: Have two
people complete Step 2.

Step 3
Rod Assembly
The foosball table comes with 4 telescopic rods for each team.
The bar scheme is as follows:
Rod with 1 blue player (Goalie)
Rod with 2 blue players (Defense)
Rod with 3 silver players (Forwards)
Rod with 5 blue players (Mid-Fielders)
Rod with 5 silver players (Mid-Fielders)
Rod with 3 blue players (Forwards)
Rod with 2 silver players (Defense)
Rod with 1 silver player (Goalie)
Take special care to ensure the direction that the player faces during this assembly step.
1
6
2 sets required
Blue Goalie
Silver Goalie
Silver Defense
Silver Mid-Fielders
Silver Forwards
Blue Mid-Fielders
Blue Forwards
Blue Defense

Step 3 (continued)
Insert Blue Goalie into first rod
holes at the end of table. Insert
rod end without bushing by tilting
rod as shown.
Ensure that player faces direction
of the arrow as shown.
Insert the opposite end with
bushing into rod hole lining pins
with screw holes in cabinet.
7

REPEAT STEP 3 A-C FOR EACH ROD AS
SHOWN BELOW
1
8
Use the diagram on Page 6 for additional assistance.
SKIP BALL DROP HOLE

Step 4
Rod Bushing Assembly
Insert the 2 part inner
bushing in the open
cabinet hole (which has
the rod extending
through) as shown. (A, B)
Ensure that it is flush with
the inside of the cabinet wall.
(C)
Install the outer bushing with
pins on the outside of
cabinet, lining it up with pins
from inner bushing. (D)
Ensure that it is flush with
the outside of the cabinet
wall. (E)
1
9
May be necessary to complete before proceeding with Step 4
8 required 8 required
16 required
M4 X 25

Step 4
Rod Bushing Assembly (Continued)
REPEAT STEP 4 A-G FOR EACH ROD
Using 2 of the M4 x 25
screws, fasten the bushing
into place.
1
10

Step 5
Rod Bearing Assembly
REPEAT STEP 5 A-E FOR EACH ROD
On the opposite cabinet
hole, slide bearing over the
end of rod. (A,B)
Insert the end cap into hole.
(C)
Ensure that it is flush with
the cabinet’s wall. (D)
Using two M4x25 screws,
fasten the end cap into
place.
11
8 required 8 required
16 required
M4 x 25

Step 6
Rod Handle Assembly
REPEAT THE STEP 6 A-B FOR EACH ROD
Place the rod handle onto
the end of the telescopic rod.
(A)
Lightly tap handle using a
hammer until the handle end
reaches the line on the rod
closest to the table. (B)
12
8 required

Step 7
Ball Drop Assembly
REPEAT STEP 7 A-E FOR THE BALL DROP
ON THE OTHER SIDE OF THE TABLE
Locate the ball drop
assembly hole on the side of
cabinet wall. It will be
directly in the middle of table
and will have 3 punched pilot
holes surrounding it. (A)
Place ball drop into the hole. (B)
Ensure that the screw holes align
with the pilot holes. (C)
Using three M2.8 x 11.5
screws, fasten the ball
holder to the table. (D,E)
13
3 required
M2.8 x 11.5
1 required

Step 8
Shroud Assembly
REPEAT STEP 8 A-C FOR SHROUD ON
OTHER SIDE OF TABLE
Place the shroud over the tables edge with the
rounded edge pointed away from the table as
shown. (A)
Using three M4 x 25
screws, fasten the back of
shroud to table.
Using the three M4 x
25 screws, fasten the
front of shroud to
table. (B)
6 required
M4 x 25
1 required
14

Step 9
Counter Assembly
REPEAT STEP 9 C-D FOR SILVER
COUNTER.
Silver counter should be behind silver goalie.
Using two M3.9x35 screws,
fasten the counter to shroud. (D)
15
Build blue and silver counters.
Separate the two blue and two silver
cubes with screw holes; these need
to be installed at each end of the
counter rods. Place all like colored
cubes on counter rod with cubes
having screw holes on each end of
both rods. (A, B)
Place blue counter into slot on
shroud behind the blue goalie. (C)
2 required
M3.9 x 35 10 required 2 required 1 required

FOOSBALL TABLE COVER
The foosball table comes
with a cover included
when purchased. Always
cover your foosball table
when not using. This
protects the table from
the elements and
increases the life of the
product to provide many
years of enjoyment!
The cover is equipped with
a Velcro side opening for
ease of use and a tie down
to ensure that the cover
stays in place.
16

17
This KETTLER® Limited Warranty applies to products sold through the KETTLER® Authorized Dealer Network to the
original retail purchaser and authenticated by proof of purchase from a retailer located in the United States. Any
shipments made under this warranty will be shipped to the United States only. Any shipment outside of the United States
will be at the sole cost of the customer. This KETTLER® Limited Warranty is a manufacturer’s warranty and is not
changed or modified by additional warranties extended by individual retailers at the point of sale. Manufacturer warrants
this product to be free from defects in material at the time of the product’s tender of delivery for a period of 3 years for
residential use. This Limited Warranty is not transferable and does not cover normal wear and tear (including, but not
limited to, damage and wear to tires, power shocks, drive belts and other non-durable parts). The liability of the
manufacturer under this Limited Warranty shall not include any liability for direct, indirect, or consequential damages
resulting from the defect. This Limited Warranty is void if the product is damaged by accident, unreasonable use,
improper service, failure to follow instructions provided, modification from its original state, or other causes determined
not arising out of defects in material.

Log onto www.kettlerusa.com/warranty and register your
KETTLER®Cavalier Foosball Table Warranty online!
www.facebook.com/kettlerusa
twitter.com/kettler_usa
www.youtube.com/kettlerusa

KETTLER®International Inc.,
1355 London Bridge Road, Virginia Beach, VA 23453 USA
www.kettlerusa.com • E-mail: [email protected]om
For parts/service: call 866-804-0440 or e-mail [e-mail]
Docu 12.03.12
©2012 KETTLER
®
All rights reserved. No part of this manual may be
reproduced, stored in a retrieval system, or transmitted in any form, or
by any means, such as electronic, mechanical, photocopying or
otherwise, without the prior written permission of KETTLER®.