Keurig K-Cup K145 User manual

1
Owner’s manual
Keurig® K-Cup® K145 Brewer
manuel D’uTIlIsaTIOn
Cafetière à K-Cup® K145 de Keurig®

2
IMPORTANT SAFEGUARDS Safe Operation & Use
When using electrical appliances, basic
safety precautions should be followed,
including the following:
1. Read all instructions before using.
2. Do not touch hot surfaces.Use handles
and knobs when available.
3. This appliance must be properly
installed and located in accordance
with these instructions before it is used.
4. The use of accessory attachments
not recommended by the appliance
manufacturer may result in fire,
electrical shock or injury to persons.
5. Do not place on or near a hot gas or
electric burner, or in a heated oven.
6. Do not use outdoors.
7. To protect against fire, electric shock
and injury do not immerse cords,
plugs, or the appliance in water or
any other liquid.
8. Do not overfill the Water Reservoir
with water.
9. Use only water in this appliance! Do
not put any other liquids or foods in the
Water Reservoir except as instructed in
the Cleaning Instructions in this guide.
10. Turn off and unplug the brewer before
cleaning or maintenance. Allow to cool
before putting on or taking off parts
and before cleaning the appliance.
11. For best operation, plug the appliance
into its own electrical outlet on a
dedicated circuit to prevent flickering
of lights, blowing of fuses or tripping a
circuit breaker.
12. Do not operate any appliance with a
damaged cord or plug or after the
appliance malfunctions or is damaged
in any manner. Contact Keurig
Customer Service to report any
malfunction of or damage to
the brewer.
13. Do not let the cord hang over the
edge of the table or counter, or touch
hot surfaces.
14. To disconnect, press the POWER
Button on the brewer to “OFF” status
and then remove the plug from the
wall outlet.
15. Close supervision is necessary
when any appliance is used by or
near children.
16. Do not lift the brewer Handle while
brewing is in progress.
17. Always keep the Water Reservoir Lid
on the Water Reservoir unless you are
refilling it.
18. This appliance is equipped with a Power
Cord having a grounding wire with a
grounding plug. The appliance must
be grounded using a 3-hole properly
grounded outlet. In the event of an
electrical short circuit, grounding
reduces the risk of electrical shock.
19. If the outlet is a standard 2-prong wall
outlet, it is your personal responsibility
and obligation to have it replaced with a
properly grounded 3-prong wall outlet.
20.Do not, under any circumstances, cut or
remove the third (ground) prong from
the Power Cord or use an adapter.
21. Consult a qualified electrician if
the grounding instructions are not
completely understood, or if doubt
exists as to whether the appliance is
properly grounded.
22.Do not use the appliance for other than
its intended use.
SAVE THESE
INSTRUCTIONS.

3
TABLE OF CONTENTS
KEURIG®SINGLE CUP COMMERCIAL BREWING SYSTEM
K145 Brewer — Using Your Brewer
BREWER OVERVIEW
Helpful Hints........................................................................................4
Unpacking ............................................................................................4
Features ...............................................................................................5
SECTION 1—SET-UP & FIRST BREW
Setting Up Your Brewer......................................................................6
Brew Your First Cup............................................................................7
Stopping the Brew Process...............................................................8
Adding Water........................................................................................8
Brewing Iced Beverages & Hot Water.............................................9
SECTION 2—MENU CONTROLS & INDICATORS
Menu Controls & Indicators..............................................................9
SECTION 3—CLEANING & MAINTENANCE
Cleaning..............................................................................................10
Descaling............................................................................................ 11
Draining & Storage........................................................................... 12
SECTION 4—TROUBLESHOOTING..................................................13
SECTION 5 —WARRANTY................................................................ 15
Pour des directives en français, veuillez vous reporter à la page 16.
Record your brewer serial number here.
See unpacking instructions on page 4 for serial number location.
Removing the serial number label from the brewer will void warranty.
WARNING TO USERS AND PARENTS
1. DO NOT permit children to use brewer unless there is adult
supervision. Brewer dispenses very hot water.
2. SPECIAL NOTICE FOR HOT COCOA USERS: IMMEDIATELY AFTER
USING A HOT COCOA K-CUP® PACK, RUN a Hot Water Brew Cycle
without a K-Cup®pack to avoid the possibility of clogging the Exit
Needle. DO NOT assume the next user will do this.
CAUTION: There are two sharp needles that puncture the K-Cup®pack, one above the
K-Cup®Pack Holder and the other in the bottom of the K-Cup®Pack Holder. To avoid
risk of injury, do not put your fingers in the K-Cup®Pack Assembly Housing.
CAUTION: There is extremely hot water in the K-Cup®Pack Holder during the
brew process. To avoid risk of injury, do not lift the Handle or open the K-Cup®
Pack Assembly Housing during the brewing process.
CAUTION: Please always keep the brewer in its upright position to avoid potential
injury and/or damage to your brewer.
SHORT CORD INSTRUCTIONS: A short power supply cord is provided to reduce the
risk of becoming entangled in or tripping over a longer cord.
If an extension cord is used, (1) the marked electrical rating of the cord set or extension
cord should be at least as great as the electrical rating of the appliance; (2) the cord
should be arranged so that it will not drape over the countertop or tabletop where it can
be pulled on by children or tripped over unintentionally; and (3) the extension cord must
include a 3-prong grounding plug.
THIS PRODUCT IS FOR COMMERCIAL USE ONLY.
WARNINGTHIS PRODUCT CONTAINS CHEMICALS, INCLUDING
LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER,
BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
WARNING WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT REMOVE THE
BOTTOM COVER. NO USER SERVICEABLE
PARTS ARE INSIDE. REPAIR SHOULD BE DONE
BY AUTHORIZED SERVICE PERSONNEL ONLY.
RISK OF FIRE OR
ELECTRIC SHOCK
DO NOT OPEN !

4 5
Brewer Overview
Helpful Hints
1. Plug the brewer into its own grounded outlet.
If the electric circuit is overloaded with other
appliances, your brewer may not function
properly. The brewer should be operated on
its own circuit, separate from other
appliances.
2. Keep your brewer turned “ON.”
Keep your brewer turned “ON” at all times.
To brew a fresh cup of coffee, tea or hot cocoa
anytime you want, we suggest you keep your
brewer turned “ON” all the time. However, the
brewer is fully programmable so you can set it
to turn on and off automatically to match your
schedule. Or, if you prefer, set the brewer to
automatically turn off after a period of time.
Follow the simple instructions on page 9 to
make using the brewer convenient for you.
3. For the best tasting gourmet coffee, tea or hot
cocoa, Keurig recommends using bottled or
filtered water.
Water quality varies from place to place. If you
notice an undesirable taste in your cup of
coffee, tea or hot cocoa (such as chlorine or
other mineral tastes) we recommend you
consider using bottled water or water from a
filtration system. For best results, carefully
follow manufacturer’s instructions when
using any water filtration system.
4. Customize Your Size, Flavor & Brew.
With the choice of over 250 varieties of K-Cup®
packs and 3 brew sizes; 6 oz., 8 oz. or 10 oz.,
your Keurig®brewer gives you endless options
to customize the size, flavor and brew that’s
perfect for you. For a strong, intense cup,
select an Extra Bold K-Cup®pack (with up to
30% more ground coffee than regular
varieties) and the brew size that’s right for you.
The smaller the brew size, the more intense
the flavor in your cup. The larger the brew size,
the less intense the flavor in your cup.
5. Remove K-Cup®pack after use.
Please refer to page 7 for brewing instructions.
6. Brewing into a travel mug.
To brew into a travel mug, simply remove the
Drip Tray Assembly and place the travel mug
on the Drip Tray Base.
7. Descale the brewer regularly.
Please refer to pages 11 and 12 for
instructions.
Unpacking the Brewer
1. Place the brewer box on a large steady
surface (such as a table or countertop) or
on the floor. Open the box.
2. Remove enclosed literature and K-Cup®
variety pack.
3. Turn the box on its side with front of box
face down.
4. Reach into the box and grasp the plastic bag
that contains the brewer.
5. Carefully pull the plastic bag (and packaging
materials) toward you and out of the box. The
brewer will still be encased in the polyfoam
and be on its side.
6. Remove the top polyfoam packaging material.
7. Carefully lift the brewer off of the bottom
polyfoam and place it upright on a flat,
steady surface.
8. Lift plastic bag off of brewer.
9. Record the serial number for this brewer on
page 3 of this guide. The serial number can be
found on the bottom of the brewer box or on
the brewer behind the Drip Tray (when removed).
10. Place the brewer upright on a flat, steady
surface and remove tape.
We recommend you save all packing materials in
case future shipping of the product is necessary.
WARNING:
Keep all plastic bags away
from children.

5
Features K145 Brewer
A. Water Reservoir Lid
B. Water Reservoir
C. Lock Tabs
D. Water Reservoir
Lock Tab Slots
E. Handle
F. Funnel
G. K-Cup®Pack Holder
(F and G are the
K-Cup®Pack Holder
Assembly)
H. Lid
I. K-Cup®Pack Assembly
Housing
J. Drip Tray Plate
K. Drip Tray
L. Drip Tray Base
M. Vent
N. Power Cord
O. BREW/DRAIN
Selector Knob
P. Selector Switch
Q. BREW Button
R. POWER Button
S. POWER Light (Green)
T. AUTO-OFF Button
U. AUTO-OFF Light (Green)
V. HEATING Light (Red)
W. DESCALE Light (Amber)
X. ADD WATER Light (Blue)
Y. DRAIN BREWER Button
(used only when packing
away for storage)
Z. DRAIN BREWER
Light (Green)
K145 Brewer Controls & Indicators (LED Control Center)
L
P
U
S
H
T
O
B
R
E
W
BREW
AUTO-OFF
POWER
DRAIN BREWER
HEATING
DESCALE
ADD WATER
A
B
C
M
D
N
O
LK
J
I
F
G
H
E
V
R
Y
P
Z
Q
U
T
S
X
W

6
SECTION 1 Set-Up & First Brew
Setting Up Your Brewer
1. Unwrap cord and plug the brewer into a
grounded outlet. Remove all pieces of
packing tape.
2. Ensure BREW/DRAIN Selector Knob is set
to BREW (fig. 1).
3. Place a large mug (10 oz. minimum) on
the Drip Tray Plate.
4. Remove the Water Reservoir from the brewer
by first removing the Water Reservoir Lid (fig. 2),
then lifting Reservoir straight up and away from
the brewer (may be tight). Rinse with fresh water.
5. Fill Water Reservoir with bottled or filtered
water. The water level should reach the line just
below the top edge of the clear viewing area.
Do not overfill.
IMPORTANT: You cannot use your Keurig®brewer until
it has been set-up for its first use as set forth below.
NOTE: If the brewer has been exposed to
temperatures below freezing, allow brewer at
least two hours to reach room temperature
before brewing. A frozen or extremely cold brewer
will not operate.
6. Place Water Reservoir base into the left side of
the brewer and be sure the Water Reservoir
Lock Tabs engage with the Lock Tab Slots on
the brewer (fig. 3). Replace Water Reservoir Lid.
7. Press POWER Button found on upper right
panel of the brewer. The green POWER Light
will illuminate. NOTE: A K-Cup®pack should not
be used for this sequence.
NOTE: If the Water Reservoir is empty or not
correctly placed on the brewer, the blue ADD
WATER Light will illuminate. The BREW Button
will not be activated until water is added to the
Water Reservoir and the Water Reservoir
is in place.
8. The green brew size indicator lights on the LED
Control Center will flash to indicate the brewer
needs to be set-up. Make sure the Handle is
lowered completely before continuing.
9. Press the flashing blue BREW Button.
10. The brewer will automatically heat the water.
This will take about 4 minutes. During the
heating period, the red HEATING Light will
illuminate. Once the water is heated, the red
HEATING Light will turn off and the lights
indicating the brew size will illuminate.
NOTE: Do not lift Handle during this heating period.
P
U
S
H
T
O
B
R
E
W
BREW
AUTO-OFF
POWER
DRAIN BREWER
HEATING
DESCALE
ADD WATER
fig. 3
fig. 4
fig. 1
fig. 2
BREW DRAIN

7
Ready to Brew Your First Cup
1. If the green POWER Light is illuminated the
brewer is powered on.
2. Place a mug on the Drip Tray Plate.
3. Lift the Handle and the K-Cup®Pack Holder
will open toward you (fig. 5).
4. Select a K-Cup®pack.
NOTE: Do not remove the
foil lid or puncture the
K-Cup®pack.
5. Place a K-Cup®pack in the
K-Cup®Pack Holder (fig. 6).
NOTE: You may see small amounts of water coming out from the Vent and
dripping into the Water Reservoir during this and subsequent heating –
this is normal.
11. Lift and lower the Handle. Press the BREW Button to start a cleansing
brew (fig. 4). Pour the hot water from the mug into the sink.
12. The brewer may take 15 seconds to reheat water between brews during
which time the red HEATING Light may be illuminated. When the water
has heated, the red HEATING Light will turn off.
13. The one-time set-up process is now complete and you are ready to brew!
CAUTION: There are two sharp needles that
puncture the K-Cup®pack, one above the K-Cup®
Pack Holder and the other in the bottom of the
K-Cup®Pack Holder. To avoid risk of injury, do not
put your fingers in the K-Cup®Pack Holder.
6. Lower the Handle completely to close the Lid.
7. Rotate the Selector Switch to select your brew
size; 6 oz., 8 oz. or 10 oz. Press the BREW
Button. NOTE: If you do not push the BREW Button
in 60 seconds, the BREW Button will be disabled to
prevent accidental activation. Re-activate the
BREW Button by lifting and lowering the
Handle completely.
8. The blue BREW Button will remain illuminated
while brewing. CAUTION: There is extremely hot
water in the K-Cup®Pack Holder during the brew
process. To avoid risk of injury, do not lift the
Handle or open the K-Cup®Pack Assembly
Housing during the brew process.
9. There may be a short pause before the brewing
process begins. The entire brew process lasts
for approximately 1 minute and ends with a
burst of air to remove all liquid from the
K-Cup®pack.
10. Lift the Handle and dispose of the used
K-Cup®pack. CAUTION: K-Cup®pack will be hot.
6 oz.
8 oz.
10 oz.
fig. 6
fig. 5

8
11. Enjoy your first cup of Keurig Brewed®gourmet coffee, tea or hot cocoa!
NOTE: After brewing a hot cocoa K-Cup®pack, we recommend running a hot
water brew cycle without a K-Cup®pack.
12. The red HEATING Light may be illuminated as the water is heated for
the next brew cycle. The brewer will be ready for use in approximately
15 seconds. NOTE: During this period, your brewer will prepare for the next
brew. The pump may make a vibrating sound. This is normal.
Stopping the Brew Process
If you need to stop the brewing after the process has started, press the
POWER Button to turn the brewer off. The flow of coffee, tea or hot cocoa
will stop, the heating element will shut off and the green POWER Light will
turn off. NOTE: You may get less coffee, tea or hot cocoa in your cup during
your next brew. We recommend that you perform a cleansing brew after a
terminated brew. Then your next brew will be the proper volume.
SECTION 1 Set-Up & First Brew Adding Water
The blue ADD WATER Light will illuminate when
the water level in the Water Reservoir is low or if
the Water Reservoir has been removed (fig. 7).
The brewer will not allow you to brew when the
blue ADD WATER Light is illuminated.
The Water Reservoir can be filled in two ways.
1. Remove the Water Reservoir Lid and pour water
directly into the Water Reservoir while it is still
attached to the brewer. Fill with bottled or filtered
water. The water level should reach the line just
below the top edge of the clear viewing area.
Do not overfill. Replace the Water Reservoir Lid.
2. Remove the Water Reservoir from the brewer by
first removing the Water Reservoir Lid from the
Water Reservoir, then lifting the Water Reservoir
straight up and away from the brewer. Fill with
bottled or filtered water. Place the Water
Reservoir back on the brewer and ensure the
Water Reservoir Lock Tabs engage with the
brewer. Replace the Water Reservoir Lid on the
Water Reservoir. IMPORTANT: Do not remove the
Water Reservoir during the brewing process.
The blue ADD WATER Light will no longer be
illuminated three seconds after installing or
refilling the Water Reservoir. This delay is normal.
P
U
S
H
T
O
B
R
E
W
BREW
AUTO-OFF
POWER
DRAIN BREWER
HEATING
DESCALE
ADD WATER
fig.7

9
Menu Controls
1. Brew Size: Rotate Selector Switch to select your
brew size. This brewer gives you the option of a
6 oz., 8 oz. or 10 oz. brew.
2. POWER: Use the POWER Button to turn your
brewer on and off. The POWER Button can also
be used to stop a brew after the process
has started.
3. AUTO-OFF: When you press this button,
your brewer will turn off two hours after your
last brew.
4. BREW/DRAIN Selector Knob: This knob can
be found on the top center of the brewer.
This knob should be kept at BREW at all times.
It should be turned to DRAIN only when the
brewer needs to be drained, please refer to
instructions on page 12. At this time the green
DRAIN BREWER light starts to flash to indicate
that the brewer is ready to be drained.
5. DRAIN BREWER Button: This button is to be
used to drain the brewer, please refer to
instructions on page 12.
SECTION 2
Menu Controls & Indicators (LED Control Center)
Brewing Iced Beverages
Your iced tea and iced coffee taste best when fresh-brewed hot over ice.
1. Fill a 16 oz. cup (do not use glass) to the top with ice and place a K-Cup®
pack into your brewer.
2. Select your brew size, we recommend selecting a 6 oz. or 8 oz. brew.
Press the BREW Button.
3. Stir and enjoy!
Look for the Brew Over Ice icon on K-Cup®packs that are specially crafted to
brew over ice! IMPORTANT: Do not brew into a cup made of glass. Doing so may
cause the glass to crack or break.
Brewing Hot Water
Your brewer is able to produce hot water for use in cooking, making soups,
oatmeal, etc. Simply lift and lower the Handle on the brewer without adding a
K-Cup®pack. The blue BREW Button will flash. Be sure to have a mug on the
Drip Tray Plate and then press the BREW Button.
P
U
S
H
T
O
B
R
E
W
AUTO-OFF
DRAIN BREWER
HEATING
DESCALE
ADD WATER
POWER
BREW
fig.8

10
Cleaning External Parts
Regular cleaning of the brewer’s external components is recommended.
1. Never immerse the brewer in water or other liquids. The external
components may be cleaned with a damp, soapy, lint free, non-abrasive cloth.
2. The Drip Tray can accumulate up to 10 oz. of overflow. The Drip Tray and
Drip Tray Plate should be periodically inspected and rinsed clean. To
remove the Drip Tray Assembly, simply slide it toward you, keeping it level
at all times to avoid spilling. The Drip Tray and Drip Tray Plate should not
be placed in the dishwasher. They should be cleaned with a damp, soapy,
lint free, non-abrasive cloth and rinsed thoroughly.
Cleaning the K-Cup®Pack Holder Assembly
1. Cleaning the Parts—The K-Cup®Pack Holder
Assembly can be placed onto the top shelf of a
dishwasher. NOTE: Use low temperature cycles in
the dishwasher. To remove from the brewer, lift
the Handle and grasp the top of the K-Cup®Pack
Holder with one hand while pushing up on the
bottom of the K-Cup®Pack Holder from
underneath with the other until it releases
(fig. 10). After cleaning, align the K-Cup®Pack
Holder with the opening using the two front ribs
as a guide and snap into place from the top.
Indicators
1. AUTO-OFF Light: When the green light is
illuminated it means the AUTO-OFF time is
enabled. When the light is no longer illuminated,
the Auto-Off feature is off.
2. POWER Light: When the green light is
illuminated, it means your brewer is on.
3. HEATING Light: When the red light is illuminated,
it means the water for your brew is being heated.
When the light is no longer illuminated, your
brewer will be ready to brew your beverage.
4. DESCALE Light: When the amber light is
illuminated, it means that the scale buildup in
your brewer is interfering with its performance.
When this happens please descale your brewer.
If the amber light is blinking, it means that the
scale build up is significant enough to damage
the brewer. In such cases, descale the brewer
immediately. Refer to page 12 for instructions.
5. ADD WATER Light: If the blue light is illuminated,
it means the water level in the Water Reservoir
is either low or the Water Reservoir has been
removed. Refer to page 8 for instructions.
SECTION 3 Cleaning & Maintenance
SECTION 2 Menu Controls & Indicators
P
U
S
H
T
O
B
R
E
W
BREW
AUTO-OFF
POWER
DRAIN BREWER
HEATING
DESCALE
ADD WATER
fig.10
fig.9

11
2. Cleaning the Funnel—The Funnel can be
removed from the K-Cup®Pack Holder by
pulling on it until it pops off (fig. 11). The Funnel
is dishwasher safe. To replace it, just snap it
back onto the K-Cup®Pack Holder Assembly.
3. Cleaning the Exit Needle—The Exit Needle is
located on the inside bottom of the K-Cup®Pack
Holder Assembly. Should a clog arise due to
coffee grinds, it can be cleaned using a paper
clip or similar tool. Remove K-Cup®Pack Holder
Assembly and detach Funnel. Insert the paper
clip (fig. 11) into the Exit Needle to loosen the
clog and push it out. The K-Cup®Pack Holder is
dishwasher safe. CAUTION: There are sharp
needles that puncture the K-Cup®pack above the
K-Cup®Pack Holder and in the bottom of the K-Cup®
Pack Holder. To avoid risk of injury, do not put your
fingers in the K-Cup®Pack Assembly Housing.
Cleaning the Water Reservoir & Water Reservoir Lid
The Water Reservoir Lid and Water Reservoir should be periodically
inspected and cleaned.
The Water Reservoir Lid or Water Reservoir should not be put into the
dishwasher. They should be cleaned with a damp, soapy, lint free,
non-abrasive cloth and rinsed thoroughly. Do not dry the inside of the Water
Reservoir with a cloth as lint may remain.
To clean the filter screen of the water filter at the base of your Water Reservoir,
empty the Water Reservoir and follow one or all of the following procedures.
NOTE: If you are using a water filter inside the Water Reservoir, remove it
before cleaning.
1. Rinse the filter screen with the strong force of water from your faucet.
2. If you have a sprayer, aim the water spray at the filter screen.
3. Fill the Water Reservoir with approximately two inches of clean water and
agitate (shake) the Water Reservoir.
Empty the Water Reservoir then fill it with bottled or filtered water and return
it to the brewer. If needed, repeat above procedures. CAUTION: Please rinse
the Water Reservoir thoroughly after cleaning. This will ensure that no cleaners
or cleaning solutions remain in this area as they may contaminate the water
supply in the brewer.
Descaling Your Brewer
Depending on the mineral content of your water,
calcium deposits or scale may build up in your
brewer. Scale is non-toxic but if left unattended
can hinder brewer performance. Regularly
descaling your brewer every 3 to 6 months helps
maintain the heating element, and other internal
parts that come in contact with water. Calcium
deposits may build up faster, making it necessary
to descale more often.
Before you begin, you will need a large ceramic
mug, fresh water, descale solution and access to
a sink. Do not use a paper cup.
Properly follow the descaling procedure
described on page 12.
!
fig.11
BREW
AUTO-OFF
POWER
P
U
S
H
T
O
B
R
E
W
DRAIN BREWER
HEATING
DESCALE
ADD WATER
fig.12

12
Descaling Procedure
Empty the water from the Water Reservoir. If there is a Keurig™ Water Filter,
remove and set aside. Disable Auto-Off features for your brewer (refer to
page 10).
STEP 1: FIRST DESCALING SOLUTION RINSE
• Press the POWER Button to power the brewer off.
• Pour the entire bottle of Keurig™Descaling Solution into the Water
Reservoir. Then fill the empty bottle with bottled or filtered water and pour
into the Water Reservoir. Press the POWER Button to turn the brewer
back on.
•Place a large mug on the Drip Tray Plate and run a cleansing brew using
the largest brew size. Do not use a K-Cup®pack. Pour the contents of the
mug into the sink.
STEP 2: SECOND DESCALING SOLUTION RINSE
• Repeat the brew process without a K-Cup®pack, until ADD WATER is
indicated. Let the brewer stand for at least 30 minutes while still on.
• After 30 minutes, discard any residual solution and rinse the Water
Reservoir thoroughly.
STEP 3: FRESH WATER RINSE
• Ensure the Water Reservoir is filled with fresh water.
•Place a large mug on the Drip Tray Plate and run a cleansing brew using
the largest brew size. Do not use a K-Cup®pack. Pour the contents of the
mug into the sink.
SECTION 3 Cleaning & Maintenance •Repeat brew process until you have completed at least 12 brews using the
largest brew size. You may need to refill the Water Reservoir at least one
time during this process.
NOTE: The cleaning action of Keurig™Descaling Solution may result in a
foam dispensed from the brewer. This is natural, as the solution is reacting
with the scale inside. For a brewer that is heavily scaled, the brewer may not
fill properly after the descaler is added. If this occurs, you may see only a small
or no output dispensed followed by the sound of air blowing out. If this occurs:
• Turn off and unplug the brewer.
•If there is Keurig™Descaling Solution in the Water Reservoir, discard the
contents, rinse the Water Reservoir thoroughly and refill with water.
• Plug the brewer back in, power on, and repeat the Step 3 Fresh Water
Rinse cycle. The brewer should begin to function normally as the solution
is rinsed out and the scale is removed. If problem persists, allow the
brewer to sit unplugged for at least 30 minutes before continuing with
the rinse.
Visit us online for more information at www.keurig.com/descaling
Service
Beyond these recommended cleaning and maintenance procedures, this
brewer is not user serviceable. For service, please refer to the Warranty
section of this guide.
Draining the Brewer
The hot water tank of the K145 can be completely drained. We recommend
that the brewer be drained if it is to be transported or stored for an
extended period.

13
SECTION 4 Troubleshooting
SITUATION
Brewer does not
have power
Brewer will not
brew when used
for the first time
Brewer will
not brew
SOLUTION
•Plug the brewer into an independent outlet.
•Check to be sure that it is plugged in securely.
•Make sure that the brewer has been turned
on and the green POWER Light is illuminated.
•Reset your circuit breaker, if necessary.
•Plug into a different outlet.
•The brewer must be set-up for the first brew (refer to
page 6).
•BREW/DRAIN Selector Knob must be at the
BREW position.
•If brewer is cold/frozen, wait for two hours for it to
reach room temperature before powering on.
•BREW/DRAIN Selector Knob must be at
BREW position.
•After placing the K-Cup®pack in the K-Cup®Pack
Holder, make sure that the Handle is completely
lowered securely and the blue BREW Button
is flashing.
•If the blue ADD WATER Light is illuminated, add water
to Water Reservoir. Make sure the Water Reservoir is
seated properly in its base.
•If the blue ADD WATER Light continues to be
illuminated even after refilling, contact Customer
Service at 1.866.901.BREW (2739).
•If the blue ADD WATER Light, red HEATING Light and
blue BREW Button are all flashing simultaneously,
refer to next situation.
1. The brewer must be powered on and ready to brew.
2. Remove and empty the Water Reservoir and then replace it to the brewer.
The ADD WATER Light will be illuminated.
3. Turn the BREW/DRAIN Selector Knob to DRAIN. The green DRAIN Light
will be illuminated.
4. Press and hold the DRAIN Button. Water will flow into the Water
Reservoir. CAUTION: The water may be very hot!
NOTE: The process to drain a hot water tank from idle state takes about
one minute.
5. When the water stops flowing, release the DRAIN Button. The internal hot
water tank is now empty.
6. Turn the BREW/DRAIN Selector Knob back to BREW and power off
the brewer.
If you need assistance with your brewer, please contact Customer Service
at 1.866.901.BREW (2739).
Storage
Drain the brewer before storing and ensure that you store your brewer in a
safe and frost free environment. Please be sure to store your brewer in its
upright position to avoid water leakage from the inner tank. If you store the
brewer in a cold environment, you run the risk of water freezing inside the
brewer and causing damage. When you prepare to use it after storage, we
recommend rinsing the Water Reservoir with fresh water and running three
cleansing brews without a K-Cup®pack.
If you plan to move your brewer to a different location, turn the brewer
off, unplug it and empty the Water Reservoir. If your brewer has been in an
environment below freezing, please be sure to let it warm to room
temperature for at least two hours before using.

14
SITUATION
Blue Add Water
Light, red Heating
Light and Small
Mug Button
are all flashing
simultaneously
Brewing a
partial cup
SOLUTION
•Completely remove the Water Reservoir and
thoroughly clean (refer to page 11). Ensure the
Water Reservoir is filled. Return it to the brewer and
ensure it is seated properly, then press the flashing
BREW Button.
•If you have completed the above procedure two times
and the situation persists, contact Customer Service
at 1.866.901.BREW (2739).
•If the brewer has been set-up without a cleansing
brew, the first cup may be oversized. The next cup
will be brewed to the proper selected size.
•The Exit Needle may be clogged (refer to page 11).
•Clean K-Cup®Pack Holder if necessary (refer to
page 10).
•A partial drain process may have occurred. The
brewer will brew the next cup at the selected size.
•The Water Reservoir may have been removed during
brewing. Replace the Water Reservoir and perform
a cleansing brew without a K-Cup®pack.
•If the amber DESCALE Light is illuminated, descale
the brewer (refer to page 11).
•If you have repeated the descale procedure on
your brewer two times and it is still only brewing
a partial cup, contact Customer Service at
1.866.901.BREW (2739).
If any problems persist, contact Customer Service at 1.866.901.BREW (2739).
SITUATION
Brewer shuts off
automatically
Water appears in
the Brewer base
with the Water
Reservoir removed
Drain process notes
SOLUTION
•Check to make sure that the Auto-Off Timer feature
has not been enabled. If the green AUTO-OFF Light is
illuminated, press the black AUTO-OFF Button to
disable the Auto-Off Timer feature.
•It is normal for a small amount of water (less than
10 ml) to collect if the Water Reservoir is not seated
for a period of time. This will not affect the operation
of the brewer.
•Use clean cloth or paper towel to absorb the water.
•Return the Water Reservoir back to the brewer base
(refer to page 6, fig. 3).
•BREW/DRAIN Selector Knob turned to DRAIN during
a brew cycle: If this occurs, the brewing cycle is
immediately stopped. Recovery: The brew that
immediately follows may provide an improper volume,
so perform a brew without a K-Cup® pack. The next
brew will be of the proper selected size.
•BREW/DRAIN Selector Knob turned to DRAIN and
back to BREW: The brewer is smart and knows if the
DRAIN Button has been pressed. If it has not been
pressed, and only the knob has been turned to DRAIN
and back to BREW, the brewer does not need to be
set-up again.
•BREW/DRAIN Selector Knob turned to DRAIN and
DRAIN Button pushed, but tank not emptied. To brew,
set-up the brewer and then perform a cleansing brew
(refer to page 6).
SECTION 4 Troubleshooting

15
SECTION 5 Warranty
Limited One Year Warranty
Keurig, Incorporated warrants to the original purchaser that its brewer will
be free of defects in materials or workmanship under normal use for one
year from the date of purchase. It is recommended that you fill out and return
the warranty card enclosed with your brewer so that your purchase
information will be stored in our system. Keurig, a Keurig Authorized
Distributor or Service Agent will, at their option, repair or replace a defective
brewer or brewer parts under this warranty without charge upon its receipt
of proof of the date of purchase. If a replacement brewer is necessary to
service this warranty, the replacement brewer may be new or reconditioned.
If a replacement brewer or parts are sent, a new limited one year warranty
will be applied to the replacement brewer or parts. This warranty only
applies to brewers operated in the United States and Canada. This warranty
gives the original purchaser specific legal rights, and you may also have
other rights that vary from state to state and, in the case of Canada, from
province to province. If you obtained this brewer through sale or rental from
a Keurig Authorized Distributor, you may also want to refer to your
distributor’s warranty policies. Only the use of Keurig Brewed®K-Cup®
brand packs and accessories will guarantee the proper functioning and
lifetime of your of Keurig®K-Cup®brewer. Any damage to or malfunction of
your brewer resulting from the use of non Keurig Brewed®K-Cup®brand
packs and accessories may not be covered by this warranty or may result in
a service fee if the damage or malfunction is determined to be caused by
such use.
What is not covered by the Limited Warranty?
THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL
DAMAGES SUCH AS PROPERTY DAMAGE AND DOES NOT COVER
INCIDENTAL COSTS AND EXPENSES RESULTING FROM ANY BREACH OF
THIS WARRANTY, EVEN IF FORESEEABLE. Some states or provinces do
not allow the exclusion or limitations of incidental or consequential
damages, so the above limitation or exclusion may not apply to you
depending on the state or province of purchase. Nor does this warranty
cover damages caused by use of non Keurig Brewed®K-Cup®brand packs
or accessories, services performed by anyone other than Keurig or its
authorized service providers, use of parts other than genuine Keurig®
parts, or external causes such as abuse, misuse, inappropriate power
supply or acts of God.
Other Limitations
THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER EXPRESS
WARRANTY, WHETHER WRITTEN OR ORAL. IN ADDITION, KEURIG HEREBY
SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO
YOUR K145 BREWER, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Some
states or provinces do not allow disclaimers of such implied warranties or
limitations on how long an implied warranty lasts, so the above limitation
may not apply to you depending on the state or the province of purchase.
How do you obtain warranty service?
Keurig®brewers are high-quality appliances and, with proper care, are
intended to provide years of satisfying performance. However, should the
need arise for warranty servicing; simply call Keurig Customer Service at
our toll free phone number 1.866.901.BREW (2739). Please do not
return your brewer for servicing without first speaking to Keurig Customer
Service to obtain an Authorization to Return number (ATR). Keurig®
brewers returned without an ATR number will be returned to the sender
without servicing.
Keurig, Incorporated
55 Walkers Brook Drive
Reading, MA 01867

16
RÈGLES DE SÉCURITÉ IMPORTANTES
Fonctionnement et utilisation sans danger
Lorsque vous utilisez des appareils
électriques, vous devriez suivre les
mesures de sécurité de base suivantes :
1. Lire toutes les instructions avant
l’utilisation.
2. Ne pas toucher les surfaces chaudes.
Utiliser les poignées s’il y en a.
3. Installer correctement l’appareil et le
placer dans un endroit conforme aux
présentes instructions avant de l’utiliser.
4. L’utilisation d’accessoires non
recommandés par le fabricant de l’appareil
risque de causer un incendie, une décharge
électrique ou des blessures.
5. Ne pas placer sur un élément électrique
ou un brûleur à gaz ni à proximité. Ne pas
placer dans un four chaud.
6. Ne pas utiliser à l’extérieur.
7. Pour éviter les risques d’incendie, de
décharge électrique ou de blessures,
ne pas immerger la fiche, le cordon
d’alimentation ou l’appareil dans l’eau ni
dans aucun autre liquide.
8. Ne pas trop remplir le réservoir d’eau.
9. Utiliser seulement de l’eau dans cet
appareil! Ne verser aucun autre liquide
ou aliment dans le réservoir d’eau, à
l’exception des produits mentionnés
dans les instructions de nettoyage du
présent manuel.
10. Éteindre et débrancher l’appareil avant de
le nettoyer ou d’en faire l’entretien. Laisser
l’appareil refroidir avant d’ajouter ou
d’enlever des pièces et avant de le nettoyer.
11. Pour un fonctionnement optimal, brancher
l’appareil dans une prise de courant
séparée sur un circuit dédié pour éviter
que les lumières vacillent, que les fusibles
sautent ou que les disjoncteurs
se déclenchent.
12. Ne jamais utiliser un appareil dont la
fiche ou le cordon d’alimentation est
endommagé, ou un appareil qui présente
un trouble de fonctionnement ou qui a été
endommagé. Communiquer avec le Service
à la clientèle de Keurig pour signaler tout
mauvais fonctionnement de la cafetière ou
tout dommage à celle-ci.
13. Ne pas laisser le cordon d’alimentation
pendre d’une table ou d’un comptoir ni
entrer en contact avec une surface chaude.
14. Pour débrancher la cafetière, appuyer
d’abord sur le bouton de mise en marche
(POWER) pour éteindre l’appareil, puis
retirer le cordon de la prise.
15. Ne jamais laisser des enfants utiliser
la cafetière ni rester à proximité sans
surveillance.
16. Ne pas soulever la poignée de la cafetière
pendant une infusion.
17. Toujours laisser le couvercle sur le
réservoir d’eau, sauf lors du remplissage.
18. L’appareil est équipé d’un cordon
d’alimentation muni d’un fil et d’une fiche avec
contact de mise à la terre. L’appareil doit être
mis à la terre en utilisant une prise de courant
à contact de mise à la terre à trois trous. En
cas de court-circuit, la mise à la terre réduit
les risques de décharge électrique.
19. Si la prise de courant est une prise
de courant murale standard à deux
trous, le propriétaire a l’obligation et la
responsabilité de la faire remplacer par une
prise de courant à contact de mise à la terre
à trois trous.
20.Il ne faut en aucun cas couper ou enlever la
troisième broche (mise à la terre) de la fiche
du cordon d’alimentation, ni utiliser
un adaptateur.
21. Consulter un électricien qualifié si les
instructions sur la mise à la terre ne sont
pas parfaitement comprises ou en cas de
doutes sur la mise à la terre de l’appareil.
22.Ne pas utiliser l’appareil pour une fin autre
que celle pour laquelle il a été conçu.
CONSERVER
CE MANUEL.
AVERTISSEMENT AUX UTILISATEURS ET AUX
PARENTS
1. NE permettez PAS aux enfants d’utiliser l’appareil
sans la supervision d’un adulte. L’appareil distribue
de l’eau très chaude.
2. AVIS SPÉCIAL AUX UTILISATEURS DE CHOCOLAT
CHAUD : APRÈS L’UTILISATION D’UNE DOSETTE
K-CUP
®
DE CHOCOLAT CHAUD, LANCEZ
IMMÉDIATEMENT un cycle d’infusion d’eau chaude
sans dosette K-Cup
®
pour éviter une possible
obstruction de l’aiguille de sortie. NE tenez PAS pour
acquis que le prochain utilisateur le fera.

17
APERÇU DE LA CAFETIÈRE
Conseils utiles................................................................................... 18
Déballage ...........................................................................................18
Caractéristiques ............................................................................... 19
SECTION 1—PRÉPARATION ET PREMIÈRE INFUSION
Préparation de votre cafetière........................................................20
Infusion de votre première tasse....................................................21
Annulation d’une infusion................................................................22
Ajout d’eau..........................................................................................22
Infusion de boissons glacées et préparation d’eau chaude.......23
SECTION 2—MENU DE COMMANDES ET VOYANTS
Menu de commandes et voyants ....................................................23
SECTION 3—NETTOYAGE ET ENTRETIEN
Nettoyage...........................................................................................24
Détartrage..........................................................................................25
Vidange et entreposage ...................................................................27
SECTION 4—DÉPANNAGE...............................................................28
SECTION 5—GARANTIE...................................................................30
For English instructions, please refer to page 2.
Inscrivez le numéro de série de votre cafetière ici.
Voir les instructions de déballage à la page 18 pour savoir où se trouve le numéro de série.
Le retrait de l’étiquette du numéro de série annulera la garantie.
ATTENTION : La dosette K-Cup®est perforée par deux aiguilles, une au-dessus et
l’autre au fond du support à dosette K-Cup®. Pour éviter tout risque de blessure, ne
pas mettre les doigts dans le boîtier du support à dosette K-Cup®.
ATTENTION : L’eau se trouvant dans le support à dosette K-Cup®durant l’infusion est
extrêmement chaude. Pour éviter tout risque de blessure, ne pas soulever la poignée
ni ouvrir le boîtier du support à dosette K-Cup®durant l’infusion.
ATTENTION : Toujours garder la cafetière en position verticale pour éviter toute
blessure ou tout dommage à la cafetière.
DIRECTIVES POUR CORDON D’ALIMENTATION COURT : L’appareil est doté d’un
cordon d’alimentation court pour éviter qu’il s’emmêle ou que quelqu’un trébuche dans
un cordon long.
Si une rallonge est utilisée, (1) les caractéristiques électriques inscrites sur la rallonge
doivent égaler ou excéder celles de l’appareil, (2) le cordon doit être fixé de façon à ce
qu’il ne pende pas d’une table ou d’un comptoir pour éviter qu’un enfant puisse le saisir
ou que quelqu’un trébuche, et (3) la rallonge doit être munie d’une fiche avec contact de
mise à la terre à trois broches.
CE PRODUIT EST DESTINÉ À UNE UTILISATION COMMERCIALE SEULEMENT.
AVERTISSEMENTCE PRODUIT CONTIENT DES PRODUITS
CHIMIQUES, NOTAMMENT DU PLOMB, UN MÉTAL QUI, SELON L’ÉTAT DE LA
CALIFORNIE, CAUSE LE CANCER, DES ANOMALIES CONGÉNITALES OU
D’AUTRES MALFORMATIONS GÉNÉTIQUES.
TABLE DES MATIÈRES
SYSTÈME D’INFUSION COMMERCIAL UNE TASSE À LA FOIS
K145 DE KEURIG®—Comment utiliser votre cafetière
AVERTISSEMENT AVERTISSEMENT : POUR RÉDUIRE LES
RISQUES D’INCENDIE ET DE CHOCS
ÉLECTRIQUES, NE PAS RETIRER LE
COUVERCLE INFÉRIEUR. CET APPAREIL NE
CONTIENT AUCUNE PIÈCE RÉPARABLE PAR
L’UTILISATEUR. LES RÉPARATIONS NE
DEVRAIENT ÊTRE EFFECTUÉES QUE PAR UN
TECHNICIEN DE SERVICE AGRÉÉ.
RISQUE D’INCENDIE ET DE
CHOCS ÉLECTRIQUES
NE PAS OUVRIR !

18 19
Conseils utiles
1. Branchez la cafetière sur un circuit avec mise à
la terre où elle seule est branchée.
Une surcharge du circuit électrique avec
plusieurs appareils risque de nuire au
fonctionnement de votre cafetière. Celle-ci
devrait être branchée séparément des autres
appareils, sur son propre circuit électrique.
2. Laissez votre cafetière en marche.
Laissez votre cafetière allumée en tout temps.
Nous vous suggérons de toujours laisser votre
cafetière allumée. Vous pourrez ainsi savourer
une tasse de café, de thé ou de chocolat chaud
fraîchement infusé à tout moment. Toutefois,
la cafetière est entièrement programmable,
ce qui vous permet de la mettre en marche ou
de l’arrêter aux moments qui vous
conviennent. Si vous préférez, vous pouvez
également régler la cafetière pour qu’elle
s’arrête après une certaine période de temps.
Veuillez consulter les instructions de la
page 23 pour que le réglage de votre cafetière
réponde à vos besoins.
3. Pour obtenir le meilleur café gourmet, thé de
spécialité ou chocolat chaud possible, Keurig
recommande l’utilisation d’eau embouteillée
ou filtrée.
La qualité de l’eau varie d’un endroit à l’autre.
Si votre café, thé ou chocolat chaud a un goût
désagréable de chlore ou de minéraux, nous
vous recommandons d’utiliser de l’eau
embouteillée ou de l’eau filtrée à l’aide d’un
système de filtration d’eau. Pour de meilleurs
résultats, suivez attentivement les instructions
du fabricant lorsque vous utilisez un système de
filtration d’eau.
4. Personnalisez le format, la saveur et l’infusion.
Avec plus de 250 variétés de K-Cups et trois
formats de tasse – 171 ml (6 oz), 236 ml (8 oz)
ou 296 ml (10 oz) –, votre cafetière Keurig®
vous offre d’infinies possibilités de formats, de
saveurs et d’infusions pour préparer la
boisson idéale pour vous. Pour une boisson
forte au goût prononcé, choisissez une dosette
K-Cup®très intense, qui contient 30 % plus de
café que nos dosettes ordinaires, et le format
de tasse qui vous convient. Plus le format de
tasse est petit, plus la saveur sera forte. Plus
le format de tasse est grand, plus la saveur
sera douce.
5. Retirez la dosette K-Cup®après utilisation.
Voir les directives d’infusion à la page 21.
6. Infusez votre café dans une tasse de voyage.
Pour infuser un café dans une tasse de voyage,
vous n’avez qu’à retirer la cuvette d’égouttage
et à placer la tasse de voyage sur la base de
la cuvette.
7. Détartrez régulièrement la cafetière.
Voir les directives aux pages 25 et 26.
Déballage de la cafetière
1. Placez la boîte de la cafetière sur une grande
surface plane et stable, comme une table
ou un comptoir, ou sur le plancher. Ouvrez
la boîte.
2. Enlevez la documentation et l’assortiment de
dosettes K-Cup® fournis.
3. Couchez l’emballage sur le côté, avec la partie
avant de la boîte en dessous.
4. Ouvrez la boîte et saisissez le sac de plastique
contenant la cafetière.
5. Tirez soigneusement le sac de plastique (et le
matériel d’emballage) vers vous pour le sortir
de la boîte. La cafetière est encastrée dans le
polymousse et repose sur le côté.
6. Retirez la partie supérieure du polymousse.
7. Retirez soigneusement la cafetière de la base
de polymousse et placez-la debout sur une
surface plane et stable.
8. Enlevez le sac de plastique de la cafetière.
9. Inscrivez le numéro de série de la cafetière à
la page 17 de ce manuel. Le numéro de série
est indiqué sous la boîte de la cafetière, de
même que sur la cafetière, derrière la cuvette
d’égouttage (visible quand on retire la cuvette).
10. Placez la cafetière debout sur une surface
plane et stable, puis retirez le ruban.
Nous vous recommandons de conserver tout
le matériel d’emballage au cas où il serait
nécessaire de retourner la cafetière.
AVERTISSEMENT :
Gardez tous les sacs de plastique
hors de la portée des enfants.
Aperçu de la cafetière

19
P
U
S
H
T
O
B
R
E
W
BREW
AUTO-OFF
POWER
DRAIN BREWER
HEATING
DESCALE
ADD WATER
A
B
C
M
D
N
O
LK
J
I
F
G
H
E
V
R
Y
P
Z
Q
U
T
S
X
W
Caractéristiques Cafetière K145 de Keurig®
A. Couvercle du réservoir
d’eau
B. Réservoir d’eau
C. Languettes de
verrouillage
D. Fentes pour languettes
de verrouillage du
réservoir d’eau
E. Poignée
F. Entonnoir
G. Support à dosette
K-Cup®(F et G forment
l’assemblage du
support à dosette
K-Cup®)
H. Couvercle
I. Boîtier du support à
dosette K-Cup®
J. Plateau à tasse
K. Cuvette d’égouttage
L. Base de la cuvette
d’égouttage
M. Évent
N. Cordon d’alimentation
O. Sélecteur infusion/
vidange (BREW/DRAIN)
Cafetière K145 de Keurig®Commandes et voyants
(panneau de commande à DEL)
P. Sélecteur
Q. Bouton d’infusion (BREW)
R. Bouton de mise en marche
(POWER)
S. Voyant d’alimentation
(POWER) vert
T. Bouton d’arrêt automatique
(AUTO-OFF)
U. Voyant d’arrêt automatique
(AUTO-OFF) vert
V. Voyant de chauffage
(HEATING) rouge
W. Voyant de détartrage
(DESCALE) ambre
X. Voyant Ajouter de l’eau
(ADD WATER) bleu
Y. Bouton de vidange de la
cafetière (DRAIN BREWER)
(utilisé uniquement en cas
d’emballage aux fins
d’entreposage)
Z. Voyant de vidange
(DRAIN BREWER) vert

20
SECTION 1 Préparation et première infusion
Préparation de votre cafetière
1. Déballez le cordon et branchez la cafetière
dans une prise mise à la terre. Retirez tous les
rubans adhésifs.
2. Assurez-vous que le sélecteur infusion/vidange
(BREW/DRAIN) est en position infusion
(BREW) (fig. 1).
3. Placez une grande tasse (au moins 296 ml/10 oz)
sur le plateau à tasse.
4. Retirez le réservoir d’eau de la cafetière en
enlevant le couvercle du réservoir (fig. 2), puis en
soulevant le réservoir à la verticale et en le tirant
ensuite vers l’avant de la cafetière (le réservoir
peut offrir une certaine résistance). Rincez-le à
l’eau fraîche.
IMPORTANT : N’utilisez pas votre cafetière Keurig®
avant de l’avoir préparée pour une première
utilisation, tel qu’indiqué ci-dessous.
REMARQUE : Si la cafetière a été placée dans un
endroit où la température était inférieure au point
de congélation, laissez-lui au moins deux heures
pour atteindre la température ambiante avant de
l’utiliser. Une cafetière gelée ou très froide ne pourra
pas fonctionner.
5. Remplissez le réservoir d’eau filtrée ou
embouteillée jusqu’à ce que le niveau atteigne
la ligne juste en dessous de la limite supérieure
de la fenêtre translucide. Ne pas trop remplir
le réservoir.
6. Replacez la base du réservoir d’eau sur le côté
gauche de la cafetière et assurez-vous que les
languettes de verrouillage du réservoir
s’engagent correctement dans les fentes de la
cafetière (fig. 3). Replacez le couvercle du
réservoir d’eau.
7. Appuyez sur le bouton de mise en marche
(POWER) situé sur le panneau supérieur droit
de la cafetière. Le voyant vert d’alimentation
(POWER) s’allumera. REMARQUE : Ce cycle se
fait sans dosette K-Cup®.
REMARQUE : Si le réservoir d’eau est vide ou
mal installé, le voyant bleu Ajouter de l’eau
(ADD WATER) s’allumera. Le bouton d’infusion
(BREW) ne pourra être activé tant que de l’eau
n’aura pas été ajoutée dans le réservoir et que
celui-ci n’aura pas été remis en place.
8. Le voyant vert de sélection du format de tasse
sur l’afficheur de messages à DEL clignotera
pour indiquer que vous devez effectuer un cycle
de préparation. Assurez-vous que la poignée
est complètement abaissée avant de continuer.
P
U
S
H
T
O
B
R
E
W
BREW
AUTO-OFF
POWER
DRAIN BREWER
HEATING
DESCALE
ADD WATER
fig. 3
fig. 4
fig. 1
fig. 2
BREW DRAIN