Key Digital KD-X400POHK User manual

HDBaseT/HDMI via Single CAT5e/6 (Tx+Rx Set) Extenders,
support Ultra HD/4K, EDID Control, Hot Plug Control,
Full Buffer System, IR Sensor, Up/Down IR & RS-232
Power over HDBaseT/HDMI via Single CAT5e/6 (Tx+Rx Set)
Extenders, support Ultra HD/4K, EDID Control, Hot Plug
Control, Full Buffer System, IR Sensor, Up/Down IR & RS-232
The Experts in Digital Video Technology and Solutions™
KD-X400ProK
KD-X400POHK
Key Digital®Systems :: 521 East 3rd Street :: Mount Vernon, NY 10553
Phone : [phone] Fax : [phone] Web : www.keydigital.com
Rev 0 – Dec 2014
Operating Instructions
Key Digital
®
, led by digital video pioneer Mike Tsinberg,
develops and manufactures high quality, cutting-edge
technology solutions for virtually all applications where
high quality video imaging is important. Key Digital
®
is at the forefront of the video industry for Home Theater
Retailers, Custom Installers, System Integrators,
Broadcasters, Manufacturers, and Consumers.
KD-X400ProK_X400POHK_Manual.indd 2-3 1/20/15 12:25 PM

4 1
About KD-X400ProK/KD-X400POHK
KD-X400ProK/KD-X400POHK HDBaseT/HDMI (Tx & Rx) Extenders extend
1080p/60, 1920x1200, 3D signals up to 250 ft. via single Key Digital
®
KD-CAT6STP1X Super CAT6A shielded cable, or up to 200 ft. using a single
third-party CAT5e/6 cable. 4K/UHD 24/25/30/60 (4:2:0) signals are extended up
to 150 ft. using Key Digital
®
KD-CAT6STP1X Super CAT6A Shielded cable, or up to
125 ft. using a single third-party CAT5e/6 cable. In addition to HDMI video and audio
signals, KD-X400ProK/POHK carries IR and RS-232 for controlling remotely located
equipment or the RS-232 port can be used to control the KD-X400ProK/POHK.
Key Features
➔ HDBaseT via Single CAT5e/6 UTP/STP Extension: With fully automatic
adjustment of feedback, equalization, and amplification depending on
cabling length
➔ KD-X400POHK: Features power extension from Tx to Rx with Power Over
HDBaseT, Rx unit does not require power supply
➔ Signal Extension:
»Up to 150 ft. @ 4K/24/25/30/60 using KD-CAT6STP1X cabling
»Up to 125 ft. @ 4K/24/25/30/60 using third-party CAT5e/6 UTP/STP cabling
»Up to 250 ft. @ 1080p / 1920x1200 using KD-CAT6STP1X cabling
»Up to 200 ft. @ 1080p / 1920x1200 using third-party CAT5e/6 UTP/STP
cabling
➔4K/Ultra HD: Support for 4096x2160 or 3840x2160 24/25/30Hz at 4:4:4
or 60Hz at 4:2:0
➔EDID Control: Internal library features 15 default EDID configurations and native
EDID data from Output/Display devices connected via Rx
➔Hot Plug Detection Control: Enables integrator to choose if active signal voltage
is forced to connected input and output devices
➔Full Buffer System
™
:Manages TMDS re-clocking / signal re-generation, HDCP
authentication to source & display, and EDID Control handshake
Table of Contents
About KD-X400ProK/KD-X400POHK ..................................1
Quick Setup Guide ................................................3
Installation and Operation ...........................................3
Application Example ...............................................4
Connections .....................................................6
Extending IR and RS-232 Control .....................................8
Settings.........................................................10
LED Indicator Lights ...............................................13
RS-232 Commands ...............................................13
Specifications ....................................................15
Important Product Warnings & Safety Instructions: ........................16
How to Contact Key Digital
®
.........................................17
Warranty Information ...............................................18
© 2014 Key Digital, Inc. All rights reserved.
Please read all instructions to insure safe operation of the product.
You MUST use the Power Supply provided with your unit or you VOID
the Key Digital
®
Warranty and risk damage to your unit and associated
equipment.
KD-X400ProK_X400POHK_Manual.indd 1 1/20/15 12:25 PM

2 3
➔IR Sensor: Sensor powering via +5V on IR In ports collects line-of-sight IR from
remote(s) without external IR connecting block
➔Up/Down IR: Two channels of IR enable control to/from devices connected to
Tx and Rx units
➔RS-232: Bi-Directional control to/from Tx and Rx unit on DB9 connector
➔RS-232 Control Mode: Provides control of Tx unit as well as connectivity status
➔3D: Support for standard 3D stereoscopic signal formats
➔Deep Color Support: 12bit Deep Color video / 8bit color for 4K/60.
➔Lossless compressed digital audio: Support for Dolby
®
TrueHD, Dolby
®
Digital
Plus and DTS-HD Master Audio
™
➔CEC Support: For inter-device control between main input and output HDMI
channel
➔Daisy Chaining: Connection of Tx and Rx units allows almost unlimited extension
of HDMI, RS-232 and IR signals
➔HDMI
®
and HDCP Licensing: Fully licensed and compatible with all HDMI and
HDCP technologies
➔I2C Communication: EDID and HDCP authentication to Display and Source
➔Power Supplies: Included with screw-in type connectors
➔Control System Support: Compatible with Compass Control
®
, AMX
®
, Control4
®
,
Crestron
®
, KNX
®
, RTI
®
, Savant, URC
®
, Honeywell
®
, HAI
®
, Leviton
®
etc.
KD-X400ProK Accessories
➔(2) 5V 2A DC Power Supplies (Screw-In Type), (2) Mounting Brackets,
(3) Locking HDMI Cable Clips, (1) IR Emitter, (1) IR Sensor
➔KD-X400ProK requires power on both Tx and Rx units
KD-X400POHK Accessories
➔(1) 12V 2A DC Power Supply (Screw-In Type), (2) Mounting Brackets,
(3) Locking HDMI Cable Clips, (1) IR Emitter, (1) IR Sensor
➔KD-X400POHK only requires power on the Tx unit, which extends power
to the Rx unit
Quick Setup Guide
Step 1: Find a safe and convenient location to mount or place your
KD-X400ProK/KD-X400POHK units
Step 2: Begin with the KD-X400ProK/KD-X400POHK Tx/Rx units and all
input/output devices turned off with power cables removed
Step 3: Connect your HDMI source to the input port of your
KD-X400ProK/KD-X400POHK Tx unit
Step 4: Connect your HDMI displays to the output port of your
KD-X400ProK/KD-X400POHK Rx unit
Step 5: Connect KD-X400ProK/KD-X400POHK Tx unit to
KD-X400ProK/KD-X400POHK Tx with CAT5e/6 cable
Step 6: Connect additional IR/RS-232 control connections and IR sensors
Step 6: Connect power to the KD-X400ProK/KD-X400POHK Tx units
and KD-X400ProK Rx unit
Step 7: Power on input/output devices
Installation and Operation
Before permanently securing the unit for
final installation, test for proper operation of the
unit and cables in your system. It is
recommended that you leave enough ventilation
space to provide sufficient airflow and cooling.
An optional HDMI cable clip (included) allows
for a secure connection of HDMI cables to
KD-X400ProK/KD-X400POHK units and helps
prevent intermittent or complete signal loss due
to poor connectivity.
Optional HDMI Cable
clip (included)
KD-X400ProK_X400POHK_Manual.indd 3 1/20/15 12:25 PM

4 5
Application Example
iPad
Ethernet
WiFi
EDID Control
KD-MC1000
Master Controller
Satellite
RS-232
RS-232
HDMI
HDMI
CAT5e/6
KD-X400ProK
Red Ray
HDMI
HDMI
CAT5e/6
KD-X400ProK
KD-X400ProK
CAT5e/6
KD-X400ProK
KD-X400ProK
KD-X400ProK
IR Out
Display
Display
Satellite
Remote
IR Sensor
IR In
WiFi Router
Up to 150’ with Key Digital
®
KD-CAT6STP1X
Up to 150’ with Key Digital
®
KD-CAT6STP1X
Achieved 4K HDMI Extension: up to 340’
20’
20’
HDMI
Daisy-Chaining Example
iPad
Ethernet
WiFi
EDID Control
KD-MC1000
Master Controller
Satellite
RS-232
RS-232
HDMI
HDMI
CAT5e/6
KD-X400ProK
Red Ray
HDMI
HDMI
CAT5e/6
KD-X400ProK
KD-X400ProK
CAT5e/6
KD-X400ProK
KD-X400ProK
KD-X400ProK
IR Out
Display
Display
Satellite
Remote
IR Sensor
IR In
WiFi Router
Up to 150’ with Key Digital
®
KD-CAT6STP1X
Up to 150’ with Key Digital
®
KD-CAT6STP1X
Achieved 4K HDMI Extension: up to 340’
20’
20’
HDMI
KD-X400ProK_X400POHK_Manual.indd 4-5 1/20/15 12:26 PM

6 7
Rx Unit:
➔Using a short HDMI cable, connect your output / display device to the HDMI port
labeled “HDMI Output”.
➔Connect the CAT5e/6 cable at the port labeled “CAT5e/6 Input”.
➔If you are sending or receiving IR, connect it at this time
➔If you are transmitting or receiving RS-232, connect to the RS-232 port
➔Connect power to the Tx and Rx using the included power supplies and then
power up your source and display equipment.
Connections
Before making any connections, power off your source and display devices.
Tx Unit:
➔Using a short HDMI cable, connect your source device to the HDMI port labeled
“HDMI Input”. To connect DVI or Display Port, use appropriate adapters.
➔Connect the CAT6 STP cable that connects to the Rx Unit at the port labeled
“CAT5e/6 Output”.
➔Make IR In and Out connections to receive (IR In port) or send (IR Out port)
control signals. Refer to the “Extending IR & RS-232 Control” for more information.
➔Connect a DB9 cable for bi-directional RS-232 control.
Refer to the “Extending IR & RS-232 Control” for more information.
KD-X400ProK_X400POHK_Manual.indd 6-7 1/20/15 12:26 PM

8 9
➔IR In: IR In ports support two different modes, determined by the position of the
Control Rotary.
»Serial IR:
»A fixed 5V input signal with a 3.5mm mini jack
»IR signal on the tip. Mono or stereo 3.5mm mini jacks are supported, with
the ring having no contact.
»Typically fed from a dedicated control system or an IR distribution block
»IR Sensor:
»IR Sensors can be connected directly into IR In port, without the need for
an external IR distribution block
»IR signal on the Tip, with 5V powering of the IR sensor on the Ring.
IR In Tip Ring Sleeve Control Rotary Position
Serial IR IR In N/C Ground 0-3, 8-B
IR Sensor IR In 5V Ground 4-7, C-F
➔IR Out:
»Pass-through from signal of corresponding IR In port
»Driving power: 5V with 32mA minimum current
»Typically connected with an IR emitter
IR Out Tip Ring Sleeve Control Rotary Position
Serial IR IR Out N/C Ground Any
»The sleeve of the 3.5mm Male connector must have good physical contact
with 3.5 mm Female input/output on the KD-X400ProK/KD-X400POHK.
Some 3.5mm Male plugs feature a plastic sleeve that
extends longer than an average sleeve. This may
cause poor grounding contact. See the example on
the left.
Extending IR and RS-232 Control
RS-232:
Three different modes of usage are available, determined by the position of the
Control Rotary.
➔RS-232 Pass-through Mode
»Send and receive (bi-directional) RS-232 commands for controlling remote
equipment.
»Requires the use of a null-modem cable on one (either) side.
➔Control Mode
»Provides control of Tx units as well as connectivity status
»See RS-232 Commands section for more information
➔Firmware Upgrade Mode
»Two different types of firmware may be updated:
MCU (KD-X400ProK/KD-X400POHK units),
and HDBaseT (extension over CAT5e/6)
RS-232 Mode Pin 2 Pin 3 Pin 5 Control Rotary Position
Pass-through Tx Rx Ground 0 – 7
Control Tx Rx Ground 8, 9
F/W MCU Tx Rx Ground A, B
F/W HDBaseT Tx Rx Ground C, D, E, F
IR
➔Bi-directional IR control extension is supported.
»“IR In” port on the Tx unit extends to the “IR Out” port of the Rx unit
»“IR In” port on the Rx unit extends to the “IR Out” port of the Tx unit
Rotary Control Switch
KD-X400ProK_X400POHK_Manual.indd 8-9 1/20/15 12:26 PM

10 11
Control Rotary
The Control rotary enables the integrator to choose the
desired setting for IR In ports, RS-232 Mode and Hot Plug
Detection Control.
In many settings, the Control rotary setting may not match on
the Tx and Rx units.
IMPORTANT! Please apply light pressure to the Control
rotary when making your selection
Control Rotary Position Assignments:
Position IR In Mode RS-232 Mode Hot Plug Detection
Control
0 Serial IR Pass-through Bypass
1 Serial IR Pass-through Bypass
2 Serial IR Pass-through Forced HPD ON
3 Serial IR Pass-through Forced HPD ON
4 IR Sensor Pass-through Bypass
5 IR Sensor Pass-through Bypass
6 IR Sensor Pass-through Forced HPD ON
7 IR Sensor Pass-through Forced HPD ON
8 Serial IR Control Mode Bypass
9 Serial IR Control Mode Bypass
Settings
EDID Control
EDID authentication is provided from the KD-X400ProK/KD-X400POHK Tx unit to
the connected input / source device. The EDID file (AKA “handshake”) is selected
using the EDID Control rotary on the Tx unit and provides a list of compatible video
and audio formats as well as digital data, informing the source device what it should
output. Most sources will comply with a new EDID file without a power-cycle, but
each source may behave differently. Adjustments may be necessary to help achieve
desired video and audio formatting and may speed up sync time.
0Copy EDID from CAT5e/6 Output A4Kx2K@60, 2CH AUDIO
11080i, 2CH AUDIO B4Kx2K@60, DOLBY/DTS 5.1
21080i, DOLBY/DTS 5.1 C4Kx2K@60, HD AUDIO
31080i, HD AUDIO D1280x720p@60 DVI (no audio)
41080p, 2CH AUDIO E1920x1080p@60 DVI (no audio)
51080p, DOLBY/DTS 5.1 F3840x2160p@30 DVI (no audio)
61080p, HD AUDIO
Rotary EDID
Switch:
74Kx2K@30, 2CH AUDIO
84Kx2K@30, DOLBY/DTS 5.1
94Kx2K@30, HD AUDIO
IMPORTANT! Please apply light pressure to the EDID rotary when
making your selection.
KD-X400ProK_X400POHK_Manual.indd 10-11 1/20/15 12:26 PM

12 13
LED Indicator Lights
Power:
»Color: Red
»Solid illumination during power on state, as provided by healthy connection
with power supply.
HDMI Active (HDMI Input/Output):
»Color: Blue
»Solid illumination during active link (voltage + data link)
with connected HDMI input/output device
»If Hot Plug Detection is forced to input or output device from Tx or Rx unit
respectively, the HDMI Active light will illuminate solid regardless of HDMI
signal from connected device.
CAT5e/6 Input/Output:
»Color: Blue
»Solid illumination during healthy linking to Rx unit and/or if HPD is forced at
Rx unit.
RS-232 Commands
Pin 5 – Ground
Pin 3 – Receive
Pin 2 – Transmit
RS-232 cable pin out
Connection protocol is as follows:
➔Baud Rate = 57600 bits per second
➔Data Bits = 8
➔Stop Bits = 1
➔Parity = None
➔Flow Control = None
➔Carriage Return: Required
➔Line Feed: Required
Position IR In Mode RS-232 Mode Hot Plug Detection
Control
A Serial IR F/W upgrade for MCU Forced HPD ON
B Serial IR F/W upgrade for MCU Forced HPD ON
C IR Sensor F/W upgrade for HDBaseT Bypass
D IR Sensor F/W upgrade for HDBaseT Bypass
E IR Sensor F/W upgrade for HDBaseT Forced HPD ON
F IR Sensor F/W upgrade for HDBaseT Forced HPD ON
Forced Hot Plug Detection (HPD)
Hot Plug Detection (HPD) may be forced on the Tx and/or Rx units in order to
provide connected devices with necessary voltage to inform the device that a partner
(source/display) is connected and active. If the Control rotary is set to any HPD
Bypass setting, HPD signals from the output to the input device will pass as normal.
In cases of many layers of connectivity, HPD may be lost leading to no signal at the
display. In those cases, fix the Control rotary to any Forced HPD setting.
Range and Resolution:
Distance performance is significantly increased when using Key Digital KD-
CAT6STP1X Super CAT6/STP Cabling.
➔Up to 150 ft. @ 4K/24/25/30/60 using KD-CAT6STP1X cabling
➔Up to 125 ft. @ 4K/24/25/30/60 using third-party CAT5e/6 UTP/STP cabling
➔Up to 250 ft. @ 1080p / 1920x1200 using KD-CAT6STP1X cabling
➔Up to 200 ft. @ 1080p / 1920x1200 using third-party CAT5e/6 UTP/STP cabling
NOTE: Use shielded metal RJ45 connectors with
soldered ground wires when terminating shielded
CAT5e/6. Key Digital part: KD-RJ45SC (compatible
with KD-CAT6STP1X and other third-party CAT6/STP)
KD-X400ProK_X400POHK_Manual.indd 12-13 1/20/15 12:26 PM

14 15
Specifications
Technical:
➔Inputs Tx (Each): 1 HDMI, 1 IR In, 1 RS-232
➔Outputs Tx (Each): 1 CAT5e/6 UTP/STP, 1 IR Out
➔Inputs Rx (Each): 1 CAT5e/6 UTP/STP, 1 IR In
➔Outputs Rx (Each): 1 HDMI, 1 IR Out, 1 RS-232
➔DDC Signal (Data): Input DDC Signal: 5 Volts p-p (TTL)
➔HDMI Video/Audio Signal: Input Video Signal: 1.2 Volts p-p
➔HDMI Connector: Type A, 19 Pin Female
➔RJ45 Connector: Shielded Link Connector, HDBaseT
➔IR Connector: 3.5 mm monaural mini jack
➔RS-232 Connector: D-Sub 9 Pin
General
➔Regulation: CE, FCC, RoHS, WEEE
➔Enclosure: Black Metal
➔Product (Each): 6” x 4.1” x 1.2”, Weight: 0.8 lbs
➔Shipping Carton: 15.4” x 8.7” x 3.6”, Weight: 4 lbs
➔KD-X400ProK Power: 5V / 2A, 110-240 VAC, 50-60 Hz,
➔KD-X400POHK Power: 12V / 2A, 110-240 VAC, 50-60 Hz
➔Power Consumption: Tx - 2.5 Watts, Rx - 5 Watts
➔KD-X400ProK Accessories: (2) 5V 2A DC Power Supplies (Screw-In Type),
(2) Mounting Brackets, (3) Locking HDMI Cable Clips, (1) IR Emitter, (1) IR Sensor
➔KD-X400POHK Accessories: (1) 12V 2A DC Power Supply (Screw-In Type),
(2) Mounting Brackets, (3) Locking HDMI Cable Clips, (1) IR Emitter, (1) IR Sensor
Commands are not case-sensitive. Spaces shown below may be excluded.
Carriage return and line feed is required at the end of each string.
Commands:
Status:
KD-X400ProK_X400POHK_Manual.indd 14-15 1/20/15 12:26 PM

16 17
How to Contact Key Digital
®
System Design Group (SDG)
For system design questions please contact us at:
➔Phone: [phone]
➔E-mail: [email protected]
Customer Support
For customer support questions please contact us at:
➔Phone: [phone]
➔E-mail: [email protected]
Technical Support
For technical questions about using Key Digital
®
products, please contact us at:
➔Phone: [phone]
➔E-mail: [email protected]
Repairs and Warranty Service
Should your product require warranty service or repair, please obtain a
Key Digital
®
Return Material Authorization (RMA) number by contacting us at:
➔Phone: [phone]
➔E-mail: [email protected]
Feedback
Please email any comments/questions about the manual to:
➔E-mail: [email protected]
Important Product Warnings:
1. Connect all cables before providing power to the unit.
2. Test for proper operation before securing unit behind walls or in hard to access
spaces.
3. If installing the unit into wall or mounting bracket into sheet-rock, provide proper
screw support with bolts or sheet-rock anchors.
Safety Instructions:
Please be sure to follow these instructions for safe operation of your unit.
1. Read and follow all instructions.
2. Heed all warnings.
3. Do not use this device near water.
4. Clean only with dry cloth.
5. Install in accordance with the manufacturer’s instructions.
6. Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
7. Only use attachments/accessories specified by the manufacturer.
8. Refer all servicing to qualified service personnel. Servicing is required when the
device has been damaged in any way including:
»Damage to the power supply or power plug
»Exposure to rain or moisture
Power Supply Use:
You MUST use the Power Supply provided with your unit or you VOID
the Key Digital®Warranty and risk damage to your unit and associated
equipment.
KD-X400ProK_X400POHK_Manual.indd 16-17 1/20/15 12:26 PM

18 19
Warranty Information
All Key Digital® products are built to high manufacturing
standards and should provide years of trouble-free operation.
They are backed by a Key Digital Limited Lifetime Product
Warranty Policy.
http://www.keydigital.com/warranty.htm
KD-X400ProK_X400POHK_Manual.indd 18-19 1/20/15 12:26 PM

20 21
KD-X400ProK_X400POHK_Manual.indd 20-21 1/20/15 12:26 PM