Keysight Technologies S9101A User guide

Startup Guide
S9101A 5GMulti-Band
VectorTransceiver

Notices
© Keysight Technologies, Inc. 2020 – 2022
No part of this manual may be
reproduced in any form or by any
means (including electronic storage
and retrieval or translation into a foreign
language) without prior agreement and
written consent from Keysight
Technologies, Inc. as governed by
United States and international
copyright laws.
Manual Part Number
S9101-90001
Edition
Edition 1, April, 2022
Printed in USA
Published By
Keysight Technologies
1400 Fountaingrove Parkway
Santa Rosa, CA 95403
Warranty
THE MATERIAL CONTAINED IN THIS
DOCUMENT IS PROVIDED “AS IS,” AND
IS SUBJECT TO BEING CHANGED,
WITHOUT NOTICE, IN FUTURE
EDITIONS. FURTHER, TO THE
MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, KEYSIGHT
DISCLAIMS ALL WARRANTIES, EITHER
EXPRESS OR IMPLIED, WITH REGARD
TO THIS MANUAL AND ANY
INFORMATION CONTAINED HEREIN,
INCLUDING BUT NOT LIMITED TO THE
IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. KEYSIGHT
SHALL NOT BE LIABLE FOR ERRORS
OR FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES IN
CONNECTION WITH THE
FURNISHING, USE, OR
PERFORMANCE OF THIS DOCUMENT
OR OF ANY INFORMATION CONTAINED
HEREIN. SHOULD KEYSIGHT AND THE
USER HAVE A SEPARATE WRITTEN
AGREEMENT WITH WARRANTY TERMS
COVERING THE MATERIAL IN THIS
DOCUMENT THAT CONFLICT WITH
THESE TERMS, THE WARRANTY
TERMS IN THE SEPARATE
AGREEMENT SHALL CONTROL.
KEYSIGHT TECHNOLOGIES DOES NOT
WARRANT THIRD-PARTY SYSTEM-
LEVEL (COMBINATION OF CHASSIS,
CONTROLLERS, MODULES, ETC.)
PERFORMANCE, SAFETY, OR
REGULATORY COMPLIANCE, UNLESS
SPECIFICALLY STATED.
Technology Licenses
The hardware and/or software
described in this document are
furnished under a license and may be
used or copied only in accordance with
the terms of such license.
U.S. Government Rights
The Software is “commercial computer
software,” as defined by Federal
Acquisition Regulation (“FAR”) 2.101.
Pursuant to FAR 12.212 and 27.405-3
and Department of Defense FAR
Supplement (“DFARS”) 227.7202, the
U.S. government acquires commercial
computer software under the same
terms by which the software is
customarily provided to the public.
Accordingly, Keysight provides the
Software to U.S. government customers
under its standard commercial license,
which is embodied in its End User
License Agreement (EULA), a copy of
which can be found at
http://www.keysight.com/find/sweula. The
license set forth in the EULA represents
the exclusive authority by which the
U.S. government may use, modify,
distribute, or disclose the Software. The
EULA and the license set forth therein,
does not require or permit, among other
things, that Keysight: (1) Furnish
technical information related to
commercial computer software or
commercial computer software
documentation that is not customarily
provided to the public; or (2) Relinquish
to, or otherwise provide, the
government rights in excess of these
rights customarily provided to the
public to use, modify, reproduce,
release, perform, display, or disclose
commercial computer software or
commercial computer software
documentation. No additional
government requirements beyond
those set forth in the EULA shall apply,
except to the extent that those terms,
rights, or licenses are explicitly required
from all providers of commercial
computer software pursuant to the FAR
and the DFARS and are set forth
specifically in writing elsewhere in the
EULA. Keysight shall be under no
obligation to update, revise or otherwise
modify the Software. With respect to
any technical data as defined by FAR
2.101, pursuant to FAR 12.211 and
27.404.2 and DFARS 227.7102, the U.S.
government acquires no greater than
Limited Rights as defined in FAR 27.401
or DFAR 227.7103-5 (c), as applicable in
any technical data.
Safety Notices
A CAUTION notice denotes a hazard. It
calls attention to an operating
procedure, practice, or the like that, if
not correctly performed or adhered to,
could result in damage to the product
or loss of important data. Do not
proceed beyond a CAUTION notice until
the indicated conditions are fully
understood and met.
A WARNING notice denotes a hazard. It
calls attention to an operating
procedure, practice, or the like that, if
not correctly performed or adhered to,
could result in personal injury or death.
Do not proceed beyond a WARNING
notice until the indicated conditions are
fully understood and met.
ii

iii
Contents
1 Overview 1
2 Review Safety Requirements 3
2. 1 Warning Statements and Symbols 3
2. 2 Safety 4
2. 3 Weight and Dimensions 6
2. 4 Handling and Lifting 6
2. 5 Cleaning 7
2. 6 Environmental Conditions (Operating) 8
2. 7 EMC (Electromagnetic Compatibility) 9
2. 7. 1 South Korean Class A EMC Declaration 9
2. 7. 2 Declaration of Conformity 9
2. 8 Ventilation 10
2. 9 Location and Mounting 11
2. 10 Power Requirements 12
2. 11 AC Power Cord 14
2. 12 Protecting Against Electrostatic Discharge (ESD) 15
2. 13 Front and Rear Panel Symbols / Markings 16
2. 14 Returning for Service 18
3 Review Hardware Components 19
3. 1 Hardware Components 20
3. 2 Connector Descriptions 21
3. 2. 1 Connectors, 100 MHz Ref Out & 10 MHz Ref In/Out above the
RuggedFrontPanel 21
3. 2. 2 Connectors, Trig 1 and Trig 2 on the RuggedFrontPanel 21
3. 2. 3 Connectors, Transceivers on the RuggedFrontPanel 22
3. 2. 4 Connectors, M9037APXIe EmbeddedController 23
3. 2. 5 Connectors, S9101A Rear Panel (M9019APXIe Chassis) 25
3. 2. 6 Connectors, Option TR1, TR2, S9101RH mmWave Transceiver 27
3. 2. 6. 1 Ext Trig, LEDs, & Interfaces on S9101RH mmWave Transceiver 27
3. 2. 6. 2 Connectors, mmWave Side of S9101RH mmWave Transceiver 28
3. 2. 6. 3 Connectors, IF Side of S9101RH mmWave Transceiver 29
4 Install Hardware 31
4. 1 Standard Configurations 31
4. 2 Keysight S9101A-TR1 5GMulti-BandVectorTransceiver 32
4. 3 Keysight S9101A-BK1 5GMulti-BandVectorTransceiver TR1 with Blocker 34
4. 4 Keysight S9101A-TR2 5GMulti-BandVectorTransceiver 36
5 Install Software 39
6 Verify Operation 41
6. 1 Verifying X-Apps Software Controls the S9101A 42

6. 1. 1 Verify the X-Apps Software Controls the S9101A at 3 GHz 42
6. 1. 2 Verify the X-Apps Software Controls the S9101A at 28 GHz 47
7 Run Power Calibration 51
7. 1 Power Calibration Conditions 52
7. 2 Power Calibration Equipment Required 53
7. 3 Power Calibration Connectors (Ports 1 to 6) 54
7. 4 Run S910xA System Calibration Software 56
7. 4. 1 Using the Equipment Tab 57
7. 4. 1. 1 ConnectionString Examples for S9101A-TR1 59
7. 4. 1. 2 ConnectionString Examples for S9101A-BK1 60
7. 4. 1. 3 ConnectionString Examples for S9101A-TR2 61
7. 4. 1. 4 Using Keysight Connection Expert to Retrieve VISA Addresses 63
7. 4. 2 Using X-Apps to Perform Alignments 67
7. 4. 3 Using the Power Calibration Tab 68
7. 4. 3. 1 Calibrating S9101A-TR1 69
7. 4. 3. 2 Calibrating S9101A-BK1 75
7. 4. 3. 3 Calibrating S9101A-TR2 81
iv

1 Overview
S9101A 5GMulti-Band VectorTransceiver, StartupGuide 1
1 Overview
The KeysightS9101A 5GMulti-Band VectorTransceiver
is a streamlined, non-signaling measurement system that enables automated testing
of 5G New Radio (5G NR) infrastructure equipment in both the FR1 (380 MHz to 6 GHz)
and millimeter wave FR2frequencies (24.25 to 43.5 GHz).
In this document...
This document describes the installation process to start up and prepare the
KeysightS9101A 5GMulti-Band VectorTransceiver for use.
1. Review this Overview
2. Review Safety Requirementsonpage3
3. Review Hardware Componentsonpage19
4. Install Hardwareonpage31
5. Install Softwareonpage39
6. Verify Operationonpage41
7. Run Power Calibrationonpage51

2 S9101A 5GMulti-Band VectorTransceiver, StartupGuide

2 Review Safety Requirements
S9101A 5GMulti-Band VectorTransceiver, StartupGuide 3
2 Review Safety Requirements
Review all safety information in this section before operating any of the equipment:
Warning Statements and Symbolsonpage3
Safetyonpage4
Weight and Dimensionsonpage6
Handling and Liftingonpage6
Cleaningonpage7
Environmental Conditions (Operating)onpage8
EMC (Electromagnetic Compatibility)onpage9
South Korean Class A EMC Declarationonpage9
Declaration of Conformityonpage9
Ventilationonpage10
Location and Mountingonpage11
Power Requirementsonpage12
AC Power Cordonpage14
Protecting Against Electrostatic Discharge (ESD)onpage15
Front and Rear Panel Symbols / Markingsonpage16
Returning for Serviceonpage18
2. 1 Warning Statements and Symbols
The following notices are used throughout this document. Familiarize yourself with
each of the notices and their meaning before operating these products.
A CAUTION notice denotes a hazard. It calls attention to an
operating procedure, practice, or the like that, if not correctly
performed or adhered to, could result in damage to the product or
loss of important data. Do not proceed beyond a CAUTION notice
until the indicated conditions are fully understood and met.
A WARNING notice denotes a hazard. It calls attention to an
operating procedure, practice, or the like that, if not correctly
performed or adhered to, could result in personal injury or death.
Do not proceed beyond a WARNING notice until the indicated
conditions are fully understood and met.

2 Review Safety Requirements
2. 2 Safety
The safety information in this section applies to the following products.
KeysightS9101A 5GMulti-Band VectorTransceiver consists of:
PXIechassisandmodules, ruggedfrontpanel, andcables
KeysightS9101RH mmWave Transceiver
These products have been designed and tested in accordance with accepted industry
standards and have been supplied in a safe condition. This documentation contains
information and warnings that must be followed by the user to ensure safe operation
and to maintain products in a safe condition.
2. 2. 1 Safety Compliance
These products comply with the essential requirements of the European LVD (Low
Voltage Directive) as well as current editions of the following standards (dates and
editions are cited in the Declaration of Conformity):
IEC/EN 61010-1
Canada: CSA C22.2 No. 61010-1
USA: UL std no. 61010-1
2. 2. 2 Acoustic Statement (European Machinery Directive)
Acoustic noise emission
LpA <70 dB
Operator position
Normal operation mode per ISO 7779
4 S9101A 5GMulti-Band VectorTransceiver, StartupGuide

2 Review Safety Requirements
S9101A 5GMulti-Band VectorTransceiver, StartupGuide 5
2. 2. 3 General Safety Notices
If these products are not used as specified, the protection
provided by the equipment could be impaired.
These products must be used in a normal condition
(in which all means for protection are intact) only.
No operator serviceable parts inside.
Refer servicing to qualified personnel.
To prevent electrical shock, do not remove covers.
This is a Safety Protection Class I Product (provided with a
protective earthing ground incorporated in the power cord). The
Mains plug shall only be inserted in a socket outlet provided with a
protective earth contact. Any interruption of the protective
conductor inside or outside of the product is likely to make the
product dangerous. Intentional interruption is prohibited.
The KeysightS9101A 5GMulti-Band VectorTransceiver is
designed for use in Installation Category II and Pollution Degree 2,
per IEC 61010 Second Edition and 664 respectively.
The S9101A is designed for indoor use only and does not
support hot-swapping of modules; for example, inserting and
removing modules with the chassis powered up. Before installing
modules in or removing modules from the chassis, power down
the chassis, but leave the power cord connected to the AC Mains
because it serves as a ground and helps protect the chassis and
modules from electrostatic damage.

2 Review Safety Requirements
2. 3 Weight and Dimensions
KeysightS9101A:
Height: 192.4 mm (7.6 in); with feet removed
Height: 197.8 mm (7.79 in); with feet installed
Width: 449.5 mm (17.70 in); with rugged panel
Depth: 568.9 mm (22.40 in); with rugged panel (from back bumper to front BNC)
Weight: 20.4 kg (45.0 lbs) for KeysightS9101A Option TR1
Weight: 22.6 kg (49.8 lbs) for KeysightS9101A Option TR2
KeysightS9101RH mmWave Transceiver:
Height: 66 mm ( 2.6 in)
Width: 139 mm ( 5.5 in)
Depth: 183 mm ( 7.2 in)
Weight: 2.2 kg (4.85 lbs)
2. 4 Handling and Lifting
For best practice and proper ergonomics, the weight of the components may require
the assistance of two persons to lift and carry.
Use both side handles when lifting the S9101A.
Use a rolling cart when transporting the S9101A.
6 S9101A 5GMulti-Band VectorTransceiver, StartupGuide

2 Review Safety Requirements
S9101A 5GMulti-Band VectorTransceiver, StartupGuide 7
2. 5 Cleaning
Clean the outside of Keysight products with a soft, lint-free, slightly dampened cloth.
Do not use detergent or chemical solvents.
To prevent electrical shock, disconnect the S9101A from Mains
before cleaning.
Use a dry cloth or one slightly dampened with water to clean the
external case parts. Do not attempt to clean internally.
Cleaning connectors with isopropyl alcohol shall only be done
with the instruments power cord removed and in a well-ventilated
area. Allow all residual alcohol moisture to evaporate and the
fumes to dissipate prior to energizing the instrument.
Keep isopropyl alcohol away from heat, sparks, and flame. Store
in a tightly closed container. The isopropyl alcohol shall not be
stored, or left open, in the area of the equipment. Use isopropyl
alcohol with adequate ventilation to prevent the combustion of
fumes or vapors.
Avoid contact with eyes, skin, and clothing, as isopropyl alcohol
causes skin irritation, may cause eye damage, and is harmful if
swallowed or inhaled. It may be harmful if absorbed through the
skin. Wash thoroughly after handling. In case of spill, soak up with
sand or earth. Flush spill area with water. Dispose of isopropyl
alcohol in accordance with all applicable federal, state, and local
environmental regulations.
In case of fire, use alcohol foam, dry chemical, or carbon dioxide;
water may be ineffective.

2 Review Safety Requirements
2. 6 Environmental Conditions (Operating)
The S9101A is designed for use in INSTALLATION CATEGORY II
and POLLUTION DEGREE 2, per IEC 61010 Second Edition and 664
respectively.
The S9101RH mmWave Transceiver is designed for use in
Installation Category II and Pollution Degree 2, per IEC 61010-1
Third Edition and 664 respectively.
The KeysightS9101A 5GMulti-Band VectorTransceiver is designed for use in the
following conditions:
For indoor use only
Altitude up to 6,561.68 ft (2,000 m)
Operating Temperature 10 to 40° C,
Maximum Relative Humidity (non-condensing): 85% RH.
Samples of these products have been type tested in accordance with the Keysight
Environmental Test Manual and verified to be robust against the environmental
stresses of Storage, Transportation and end-use. Those stresses include, but are not
limited to temperature, humidity, shock, vibration, altitude and power line conditions.
Test Methods are aligned with IEC 60068-2 and levels are similar
to MIL-PRF-28800F Class 3.
8 S9101A 5GMulti-Band VectorTransceiver, StartupGuide

2 Review Safety Requirements
S9101A 5GMulti-Band VectorTransceiver, StartupGuide 9
2. 7 EMC (Electromagnetic Compatibility)
These products comply with the essential requirements of the European LVD (Low
Voltage Directive) as well as current editions of the following standards (dates and
editions are cited in the Declaration of Conformity):
IEC/EN 61326-1
CISPR Pub 11 group 1, class A
AS/NZS CISPR 11
ICES/NMB-001
This ISM device complies with Canadian ICES-001.
Cet appareil ISM est conforme a la norme NMB-001 du Canada.
2. 7. 1 South Korean Class A EMC Declaration
This equipment has been conformity assessed for use in business environments. In a
residential environment this equipment may cause radio interference. This EMC
statement applies to the equipment only for use in business environment.
2. 7. 2 Declaration of Conformity
Declarations of Conformity for these products and for other Keysight products may be
downloaded from the Web. Go to http://www.keysight.com/go/conformity and click
on "Declarations of Conformity." You can then search by product number to find the
latest Declaration of Conformity.

2 Review Safety Requirements
2. 8 Ventilation
VENTILATION REQUIREMENTS: When installing the product into a
cabinet, the convection into and out of the product must not be
restricted. Consideration shall also be given to the individual
instruments to avoid having the heated discharge of one
instrument, now becoming the cooling intake air for another
instrument.
Another area of concern is verification that the maximum ambient
operating temperature of the instrument(s) is not exceeded by
cabinet installation.
Keysight recommends forced air convection whenever
instrument(s) are installed in a cabinet and further recommends
that the maximum operating temperature of the cabinet be
reduced 10°C from the lowest, of the maximum operating
temperature of a single instrument.
If there are any concerns or special requirements, a Keysight Field
Engineer should be consulted to assure instrument(s)
temperature compliance and performance.
Do NOT block vents and fan exhaust: To ensure adequate
cooling and ventilation, leave a gap of at least 50mm (2") around
vent holes on both sides of the chassis.
10 S9101A 5GMulti-Band VectorTransceiver, StartupGuide

2 Review Safety Requirements
S9101A 5GMulti-Band VectorTransceiver, StartupGuide 11
2. 9 Location and Mounting
Consider ergonomics when locating any keyboard or mouse which will be used in
connection with an instrument.
Install the S9101A so that the detachable power cords are readily identifiable and is
easily reached by the operator. The detachable power cord is the disconnecting
device. It disconnects the Mains circuits from the Mains supply before other parts of
the S9101A. (The front panel switches are only standby switches and are not LINE
switches.) Alternatively, externally installed switches or circuit breakers (which are
readily identifiable and is easily reached by the operator) may be used as
disconnecting devices.
The S9101A requires a 1U space below when rack mounting.
The S9101RH mmWave Transceiver does not have an AC power connection. It is
powered by a DC voltage supplied over the
RF Cable Assembly to the LO/Pwr/Ctrl/IF In connector. The DC supply does not
represent a risk of personal injury.
The RF Cable Assembly should not be connected to, or
disconnected from, the S9101RH mmWave Transceiver while it is
suppling DC power. This connection should be made only when
powered off.
If the LED status indicator on the front of the S9101RH is lit, this
indicates that it is powered up and the cable should not be
disconnected.

2 Review Safety Requirements
2. 10 Power Requirements
100/120 VAC, 220/240 VAC
50/60 Hz
1200 W Max (Lower range), 1300 W Max (Upper range)
"WARNING: Safety of any system incorporating the equipment is
the responsibility of the assembler of the system."
The S9101A does not contain customer serviceable fuses.
Failure to ground the test set properly can result in personal
injury. Before turning on the test set, you must connect its
protective earth terminals to the protective conductor of the main
power cable. Insert the main power cable plug into a socket outlet
that has a protective earth contact only. DO NOT defeat the earth-
grounding protection by using an extension cable, power cable, or
auto-transformer without a protective ground conductor.
This instrument has auto-ranging line voltage input.
Before switching on the instrument, be sure the supply voltage is
within the specified range and voltage fluctuations do not exceed
10percent of the nominal supply voltage.
12 S9101A 5GMulti-Band VectorTransceiver, StartupGuide

2 Review Safety Requirements
S9101A 5GMulti-Band VectorTransceiver, StartupGuide 13
2. 10. 1 Before Applying Power
Verify that all safety precautions are taken. Make all connections to the unit before
applying power. Note the external markings described under Front and Rear Panel
Symbols / Markingsonpage16.
The Mains wiring and connectors shall be compatible with the
connector used in the premise electrical system. Failure to ensure
adequate earth grounding by not using the correct components
may cause product damage and serious injury.
2. 10. 2 Ground the Instrument
These products must be used in a normal condition (all means for
protection are intact).
This is a Safety Protection Class I Product (provided with a
protective earthing ground incorporated in the power cord). The
mains plug shall only be inserted in a socket outlet provided with a
protective earth contact. Any interruption of the protective
conductor inside or outside of the product is likely to make the
product dangerous. Intentional interruption is prohibited.
The S9101RH mmWave Transceiver does not have an AC power connection. It is
powered by a DC voltage supplied over the RF Cable Assembly to the LO/Pwr/Ctrl/IF
In connector. The DC supply does not represent a risk of personal injury.
The RF Cable Assembly should not be connected to, or
disconnected from, the S9101RH mmWave Transceiver while it is
suppling DC power. If the LED status indicator on the front of the
S9101RH is lit, this indicates that it is powered up and the cable
should not be disconnected.
When the S9101RH mmWave Transceiver is used, use only the RF Cable Assembly
that was supplied with the S9101RH to connect it with the other instrument and
connect it only to the mmW ports on that instrument.

2 Review Safety Requirements
2. 11 AC Power Cord
The S9101A is equipped with three-wire power cords, in accordance with
international safety standards. These power cords ground the S9101A cabinet when
connected to an appropriate power line outlet.
Use the Keysight supplied power cord or one with the same or better electrical rating.
The cable appropriate to the original shipping location is included with the S9101A.
See: http://www.keysight.com/find/powercords4
Always use the three-prong AC power cord supplied with these
products. Failure to ensure adequate earth grounding by not using
these cords can cause product damage.
If these products are not used as specified, the protection
provided by the equipment could be impaired. These products
must be used in a normal condition (in which all means for
protection are intact) only. Install the S9101A so that its
detachable power cord is readily identifiable and easily reached
by the operator. The detachable power cord is the instrument's
disconnecting device. It disconnects the Mains circuits from the
Mains supply before other parts of the instrument. The front panel
switch is only a standby switch and is not a LINE switch.
Alternatively, an externally installed switch or circuit breaker
(which is readily identifiable and is easily reached by the operator)
may be used as a disconnecting device.
The S9101RH mmWave Transceiver does not have an AC power cord connection. It is
powered by a DC voltage that is supplied over the RF Cable Assembly to the
LO/Pwr/Ctrl/IF In connector. The DC supply does not represent a risk of personal
injury.
14 S9101A 5GMulti-Band VectorTransceiver, StartupGuide

2 Review Safety Requirements
S9101A 5GMulti-Band VectorTransceiver, StartupGuide 15
2. 12 Protecting Against Electrostatic Discharge (ESD)
Electrostatic discharge (ESD) can damage or destroy electronic
components (the possibility of unseen damage caused by ESD is
present whenever components are transported, stored, or used).
Shipping Materials and ESD
Keysight’s chassis and instrument modules are shipped in materials which prevent
static electricity damage. These instruments should only be removed from the
packaging in an anti-static area, ensuring that correct anti-static precautions are
taken. Store all modules in anti-static envelopes when not installed.
Test Equipment and ESD
To help reduce ESD damage that can occur while using test equipment:
Do not use these first three techniques when working on circuitry
with a voltage potential greater than 500 volts.
Before connecting any coaxial cable to a test set connector for the first time
each day, momentarily short the center and outer conductors of the cable
together.
Personnel should be grounded with a 1 MΩ resistor-isolated wrist-strap before
touching the center pin of any connector and before removing any assembly
from the test set.
Be sure that all instruments are properly earth-grounded to prevent build-up of
static charge.
Perform work on all components or assemblies at a static-safe workstation.
Keep static-generating materials at least one meter away from all com-
ponents.
Store or transport components in static-shielding containers.
Always handle printed circuit board assemblies by the edges. This reduces the
possibility of ESD damage to components and prevent contamination of
exposed plating.
Additional Information About ESD
For more information about ESD and how to prevent ESD damage, contact the
Electrostatic Discharge Association (http://www.esda.org). The ESD standards
developed by this agency are sanctioned by the American National Standards
Institute (ANSI).

2 Review Safety Requirements
2. 13 Front and Rear Panel Symbols / Markings
Symbols that may be on the exterior of S9101A hardware components are:
Symbol Description
This symbol is used to indicate power ON and to mark the position of the instrument
power line switch.
This symbol is used to indicate power STANDBY mode (yellow in standby, green when
instrument is ON) and to mark the position of the instrument power line switch.
The AC symbol is used to indicate the required nature of the line module input power.
This symbol indicates instruction documentation.
The product is marked with this symbol when it is necessary for the user to refer to the
instruction in the documentation.
UK conformity mark is a UK government owned mark.
Products showing this mark comply with all applicable UK regulations.
The CE marking is a registered trademark of the European Community
(if accompanied by a year, it is the year when the design was proven).
It indicates that the product complies with all relevant directives.
The RCM mark is a registered trademark of the
Australian Communications and Media Authority.
The Keysight email address is required by EU directives applicable to our products.
[email protected]
This is a symbol of an Industrial Scientific and Medical Group 1 Class A product
(CISPR 11, Clause 5).
ICES / NMB-001
This is a marking to indicate product compliance with the Industry Canada
Interference-Causing Equipment Standard (ICES-001).
The following statements must be in the user documentation.
"This ISM device complies with Canadian ICES-001."
"Cet appareil ISM est conforme a la norme NMB du Canada."
South Korean Certification (KC) mark. It includes the marking's identifier code which
follows this format: R-R-Kst-ZZZZZZZ.
The crossed out wheeled bin symbol indicates that separate collection for
waste electric and electronic equipment (WEEE) is required,
as obligated by the EU DIRECTIVE and other National legislation.
Please refer to www.keysight.com/go/takeback to understand your Trade in options
with Keysight in addition to product takeback instructions.
16 S9101A 5GMulti-Band VectorTransceiver, StartupGuide