Kidde K5CO Instructions for use

1
User and Installer Guide
Battery Carbon Monoxide Alarms
Quick Start Instructions
included at the back of
this User Guide
BS EN 50291-1:2018
LICENSE NO. KM 738897
P
E
A
K
L
E
V
E
L
Alarm Operate Fault
Move to Fresh Air
Carbon Monoxide Alarm
PPM of CO displayed
Lb= Low Battery
End= End of Unit Life
MODEL: K5DCO
Alarm
Move to
Fresh Air
Operate Fault
Carbon M onox ide Al arm
Model: K5CO
Model: K5DCO
P/N: K5CO-7201-01
T
E
S
T
W
E
E
K
L
Y
/
R
E
S
E
T
T
E
S
T
W
E
E
K
L
Y
/
R
E
S
E
T
MODEL: K5DCO

2
Thank You for Purchasing this Kidde Alarm
Powered by two AA batteries, these models include a digital display (model K5DCO only), and a Reset
function to temporarily silence nuisance alarms.
Teach children how to respond to the alarm and that they should never play with the unit. This alarm is
designed to detect carbon monoxide from any source of combustion in a residential environment. It is not
designed for use in caravans, motor homes or boats.
NOTE: Please thoroughly read this user guide and save the document for future reference and to pass on
to any subsequent owner.
IMPORTANT: Additional markings can be found on the back of the unit.
The manufacturer recommends replacing this alarm ten years from the install date on the side of alarm.
Model: ______________________________
Date Code (on side): ____________________
Date of Purchase: ______________________
Where Purchased: ______________________
Date to Replace: ________________________
Product Support: 0800 917 0722
Please write down the below information
and have this at hand when you call.
ENVIRONMENTAL PROTECTION
Waste electrical products should not be disposed of with household
waste. Please recycle where facilities exist. Check with Local Authority
or Supplier for recycling advice.
Model: ______________________________
Date Code (on side): ____________________
Date of Purchase: ______________________
Where Purchased: ______________________
Date to Replace: ________________________

3
Contents
1. Carbon Monoxide Alarm: What To Do When the Alarm Sounds.................................................................................... 4
2. Other Alarm Visual and Audible Indicators.................................................................................................................................... 5
3. Troubleshooting Guide.............................................................................................................................................................................. 6
4. Introduction, Product Features and Specifications.................................................................................................................. 7
5. Limitations of CO Alarms........................................................................................................................................................................ 9
6. Recommended Locations for Alarms..............................................................................................................................................10
7. Locations to Avoid.......................................................................................................................................................................................11
8. Installation.........................................................................................................................................................................................................12
9. Operation and Testing............................................................................................................................................................................. 13
10. Recognizing Nuisance Alarms............................................................................................................................................................. 14
11. Battery ................................................................................................................................................................................................................ 15
12. General Carbon Monoxide (CO) Information............................................................................................................................. 16
13. Cleaning Your Alarm.................................................................................................................................................................................. 18
14. Service and Warranty................................................................................................................................................................................. 19
Quick Start Instructions .......................................................................................................................................................................... 20

4
1. Carbon Monoxide Alarm: What To Do When the Alarm Sounds
The carbon monoxide (CO) alarm pattern is four quick beeps repeating every 5 seconds. The red LED blinks in sync
with the beep pattern. The digital display on model K5DCO will show the PPM level of CO detected.
WARNING: CARBON MONOXIDE ALARM ACTIVATION INDICATES THE PRESENCE OF CARBON
MONOXI O AT HIGH CONCENTRATIONS WHICH CAN KILL YOU.
Based on recommendations from EN 50292, follow these steps if alarm sounds:
1. Keep calm and open all doors and windows. Turn off all fuel-burning appliances if possible. Note: it is possible
that outdoor conditions could influence domestic CO alarms (bad traffic pollution in cold weather, for
example). In these circumstances, the level of indoor CO might actually increase when doors and windows
are opened.
2. If the alarm continues to sound, even after being reset (where appropriate), then evacuate the premises,
alerting other occupants to the risk. Leave doors and windows open. Do not re-enter the premises.
3. Get medical help for anyone suffering the effects of CO poisoning, and advise that CO inhalation is suspected.
4. Call Gas Emergency Services: 0800 111 999, or your local Gas Safe Registered Engineer:
PHONE NUMBER:
Never restart the source of the CO problem until it has been corrected.
Never ignore the sound of the alarm!
NOTE: See Section RECOGNIZING NUISANCE ALARMS, for nuisance alarm situations.

5
2. Other Alarm Visual and Audible Indicators
Operational Mode Visual Indications Audible Indications Action/Note:
Normal (standby) Green LED blinks approx every
30 sec.
Test (button press when
no alarm condition is
present) Red LED blinks in sync with beep
pattern.
Green and amber LEDs illuminate.
Model K5DCO digital display will
show 3 dashes and then “888”.
4 loud pulses, a pause,
4 loud pulses.
Single beep
Perform test button press
once a week to verify proper
alarm operation.
CO Alarm Memory (unit
has experienced a CO
alarm event or 100 ppm
or more CO within the
last 14 days)
Red LED blinks every 60 sec. None. Model K5CO: Push button to
clear Alarm Memory.
Model K5DCO: Push Test/
Reset while the Peak Level
button is depressed to clear
Alarm Memory.
Peak Level CO
K5DCO only
Digital display shows the highest
CO reading between 11 and 999
ppm since the peak level was
reset.*
None. Push test/reset button while
peak level button is depressed
to clear peak level memory.
CO alarm reset Red LED continues to signal the
alarm pattern.
After button push: CO
alarm pattern stops. present or if it experienced a
nuisance situation. Re-alarm
means danger. Move to fresh
air and call 0800 111 999.
* NOTE: CO levels up to 30ppm can occur under normal non-dangerous conditions. Such conditions could include

6
3. Troubleshooting Guide
NOTE: If at any time your alarm fails to operate correctly (erratic or low sound, for example), or if you require further
information, please contact customer support at 0800 917 0722.
Trouble Condition Visual Indications Audible Indications Action:
Low Battery Amber LED blinks every
60 sec.
Model K5DCO digital
display will show “Lb”.
Chirp every 60 sec. * Push test button once to silence for 24 hrs.
Note: 30 days after Low Battery begins, the
* Replace batteries as soon as possible.
Fault Mode Amber LED blinks every
30 sec.
Model K5DCO digital
display will show “Err”.
Chirp every 30 sec. * See Cleaning Your Alarm section.
* Push test button once to attempt to reset
the unit.
End of Unit Life Amber LED blinks twice
every 60 sec.
Model K5DCO digital
display will show “End”.
Two chirps every
60 sec.
* Push button once to silence for 24 hrs.
Note: 30 days after End of Unit Life begins, the
* Remove, dispose unit, and replace as soon
as possible.
MCU FailureNone. Constant tone. * Replace alarm.
Stuck Button Amber LED blinks
every 5 sec.
Chirp every 5 sec. * Push button to dislodge it from being stuck.
If button cannot be unstuck, remove, dispose
unit, and replace as soon as possible.
3. Troubleshooting Guide

7
4. Introduction, Product Features and Specifications
Introduction
This alarm detects carbon monoxide using an electrochemical cell. Many times throughout this User Guide,
we will refer to Carbon Monoxide as “CO.”
Ten (10) years after the unit was installed, this unit will automatically alert you that it is time to replace the unit.
This is called “End of Unit Life” mode. See Troubleshooting Guide. To help track the life of your alarm, write the
installation date in the space provided on the side of the alarm. A label has been provided that has important
information on what to do in case of a CO alarm. Place the label at eye level on a wall near the alarm after it is
mounted.
Product Features and Specifications:
Temperature Operating Range: -10°C to 45°C
Humidity Operating Range: up to 90% RH non-condensing
Audible Alarm: 85+ dB(A) at 3 m, 3.0 to 3.5 kHz pulsing alarm
Digital Display (K5DCO only)
NOTE: Depending on the ambient condition (temperature, humidity) and the condition of the sensor,
the display readings may vary. The digital readings tolerances are 0-999 ± 30% +15ppm during these
conditions: Ambient: 27°C ± 12°C (80°F ± 10°F), atmospheric pressure ±10%, 40% ± 3% relative humidity
CO Sensor: Electrochemical
Peak Level Memory (K5DCO only)
CO Alarm Reset
Powered by AA batteries
Storage and Transport Conditions: -20° C to +60° C, 5-95%RH (non-condensing)

8
Product Features
Gr een,
Pow er LED
Red,
Ala rm LED
Test / Reset
Button
Model: K5CO
Alarm
Move to
Fresh Air
Operate Fault
Carbon Monoxide Alarm
P
E
A
K
L
E
V
E
L
Alarm Operate Fault
Move to Fresh Air
Carbon Monoxide Alarm
PPM of CO displayed
Lb= Low Battery
End= End of Unit Life
Gr e
Amber,
Fault LED
Amber,
Fault LED
en,
Pow er LED
Red,
Ala rm LED
Test / Reset
Button
Peak Level Button
Digital Display
with digital display
Model: K5DCO
T
E
S
T
W
E
E
K
L
Y
/
R
E
S
E
T
T
E
S
T
W
E
E
K
L
Y
/
R
E
S
E
T

9
5. Limitations of CO Alarms
WARNING: PLEASE READ CAREFULLY AND THOROUGHLY
This alarm is not intended to alert hearing impaired individuals.
LIMITATIONS OF CO ALARMS
IMPORTANT: This alarm is designed to detect carbon monoxide gas from ANY source of combustion. It is
NOT designed to detect any other gas. This alarm has not been tested specifically for use in caravans or
boats. Only CO alarms certified to EN50291-2 are fully approved for this purpose.
CAUTION: This alarm will only indicate the presence of carbon monoxide gas at the sensor. Carbon
monoxide gas may be present in other areas. Never restart the source of a CO problem until it has been
fixed. NEVER IGNORE THE ALARM!
WARNING: THIS PRODUCT IS INTENDED FOR USE IN ORDINARY INDOOR LOCATIONS OF
FAMILY LIVING UNITS. IT IS NOT DESIGNED TO MEASURE COMPLIANCE WITH COMMERCIAL
AND INDUSTRIAL STANDARDS. THIS ALARM IS NOT SUITABLE FOR INSTALLATION IN HAZARD
OUS LOCATIONS.
IMPORTANT: THIS CARBON MONOXIDE ALARM IS DESIGNED TO DETECT CARBON MONOXIDE
FROM ANY SOURCE OF COMBUSTION INCLUDING IMPROPER OR MALFUNCTIONING APPLIANC
ES. THE INSTALLATION OF THIS DEVICE SHOULD NOT BE USED AS A SUBSTITUTE FOR PROPER
INSTALLATION, USE AND MAINTENANCE OF FUEL BURNING APPLIANCES INCLUDING APPRO
PRIATE VENTILATION AND EXHAUST SYSTEMS.
This alarm does not prevent CO from occurring, nor can it solve any existing CO problem.
WARNING: THIS DEVICE IS DESIGNED TO PROTECT INDIVIDUALS FROM ACUTE EFFECTS OF
CARBON MONOXIDE EXPOSURE. IT MAY NOT FULLY SAFEGUARD INDIVIDUALS WITH SPECIFIC
MEDICAL CONDITIONS. IF IN DOUBT, CONSULT A MEDICAL PRACTITIONER. INDIVIDUALS WITH
MEDICAL PROBLEMS MAY CONSIDER USING WARNING DEVICES WHICH PROVIDE AUDIBLE AND
VISUAL SIGNALS FOR CARBON MONOXIDE CONCENTRATIONS UNDER 30 PPM.
This alarm has not been investigated for carbon monoxide detection below 50 PPM.
This alarm requires a continuous supply of electrical power – it will not work without power.
WARNING: THIS CARBON MONOXIDE ALARM IS NOT A SUBSTITUTE FOR INSTALLING AND
MAINTAINING AN APPROPRIATE NUMBER OF SMOKE ALARMS IN YOUR HOME. THIS ALARM
WILL NOT SENSE SMOKE, FIRE, OR ANY POISONOUS GAS OTHER THAN CARBON MONOXIDE.
FOR THIS REASON YOU MUST INSTALL SMOKE ALARMS TO PROVIDE EARLY WARNING OF FIRE
AND TO PROTECT YOU AND YOUR FAMILY FROM FIRE AND ITS RELATED HAZARDS.

10
6. Recommended Locations for CO Alarms
Note: CO alarms should be installed following the guidance of relevant local standards, such as
EN 50292.
Whether the alarm is wall-mounted or ceiling mounted, place the alarm a horizontal distance of between
1 metre and 3 metres from a fuel burning appliance.
When mounting the alarm on the wall, use an inside wall with the top edge of the alarm at a minimum
of 150 mm below the ceiling. The bottom of the alarm should also be at a level greater than the height
of any door or window.
Locate within hearing distance of bedrooms* and place at sleeping height if a heating appliance is in the
bedroom.
CO alarms in rooms with sloped ceilings should be located on the high side of the room.
Ceiling mounted alarms should be at least 300 mm from any wall.
If there is a partition in the room, locate the alarm on the same side of the partition as the potential source.
* A CO alarm should be installed in all rooms containing a fuel burning appliance. Additional CO alarms
should be installed in rooms where most awake time is spent, in every sleeping area, and on every level of
the home.

11
7. Locations to Avoid
In the garage. Products of combustion are present when you start your motor vehicle.
Do not install alarms adjacent to, or directly above, heaters or air-conditioning vents.
In very humid areas (above 90% RH, non-condensing), such as bathrooms and shower rooms. Do not install
directly above a sink, or near dishwashers or washing machines. Moisture or steam can cause nuisance
alarms.
Do not install within 1 m of heating or cooking appliances, measured horizontally.
In an area where the temperature may fall below -10 ºC or rise above 45 º C such as garages and unfinished
attics.
Do not install alarms in dusty areas. Dust particles may cause nuisance alarm or failure to alarm.
In insect-infested areas.
Within 300 mm of a light fitting, as electronic “noise” generated by the electronics may cause nuisance
alarms.
Do not install in an enclosed space (cupboard) or where the ventilation openings in the unit could be
impeded by items such as newspapers, table-cloths, furniture, curtains, etc.
Do not install next to a door, window, extractor fan, flue, chimney, or any other area where high air flow
may occur or the unit may be directly exposed to weather.
Do not install in locations that are difficult or dangerous to reach for testing or maintenance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.

12
8. Installation / Activation
CAUTION: THIS UNIT IS SEALED. THE COVER IS NOT REMOVABLE!
NOTE: YOUR CO ALARM MUST BE INSTALLED BY A COMPETENT PERSON, AND IS TO BE
INSTALLED ACCORDING TO THESE INSTRUCTIONS.
After selecting the proper alarm location as described in the “Recommended Locations for CO Alarms” section,
you may choose either a wall mounting or free-standing installation.
Wall-mounting (recommended by the manufacturer, if possible)
1. Drill two holes in a wall 78 mm apart (you may wish to use the back-plate for guidance)
2. Insert the two wall plugs, that are supplied, into the holes
3. Insert the two screws as supplied into the holes ensuring enough of the screw sticks out of the wall
(approx. 3mm)
4. Hook the alarm back-plate over the screws
Free-standing
ALWAYS BE CAREFUL TO LOCATE A FREE-STANDING ALARM WHERE IT IS UNLIKELY TO BE KNOCKED TO THE
FLOOR, AND IN ACCORDANCE WITH THE RECOMMENDED LOCATIONS SECTION.
Ensure free-standing alarms are placed in the upright position, and not lying flat on a surface.
Activation
1. Remove the batteries from the pack and insert them into the battery compartment. Make sure that you fit
the batteries in accordance with the polarity markings (+ or -) within the battery compartment. If correctly
installed, the alarm will give a short beep.
2. Slide the alarm onto the back-plate.
The alarm is now activated! After installation / activation, test your alarm as described in Operation and Testing
section.
WARNING: FAILURE TO PROPERLY INSTALL AND ACTIVATE THIS ALARM WILL PREVENT
PROPER OPERATION OF THIS ALARM AND WILL PREVENT ITS RESPONSE TO HAZARDS.

13
9. Operation and Testing
Operation
The alarm is operating once it is activated and testing is complete (see “TESTING” below). When CO is detected,
the unit sounds a loud alarm. See Section 1 for alarm signal descriptions. In high levels of CO, the unit will go
into alarm in a shorter period of time than at low levels of CO.
Testing
Test your alarm weekly, or after returning from a vacation or absence, by pressing and releasing the button
quickly. A quick beep will conrm the button has been pushed followed by the test sequence. See Other Alarm
Visual and Audible Indicators table. The alarm will sound if the electronic circuitry, horn, and batteries are work-
ing. If the alarm does not sound, or gives erratic or low volume sound, the unit must be replaced.
WARNING: DUE TO THE LOUDNESS OF THE ALARM, ALWAYS STAND ABOUT 1 METRE AWAY
FROM THE UNIT OR USE EAR PROTECTION WHEN TESTING.
BUMP TEST MODE
This alarm includes a “bump test” mode that will allow the alarm to be qualitatively tested during eld
service using commercially available aerosol CO.
1. Hold the test button down for 10 seconds.
2. The unit will chirp 3 times indicating the start of test mode.
3. The Green LED ashes once per second during test mode.
4. Apply the commercially available aerosol CO.
5. CO alarm sounds if CO reading is above 40 ppm.
6. The alarm will automatically exit from the bump test mode after 2 minutes followed by reset.
NOTE: The test can be terminated manually by pressing the test button.
PParts per Million (PPM) of COof CO TITime until Alarm
50 Minutes
100 Minutes
300 Must alarm in less than 3 minutes
CAUTION: This unit should only be bump tested using clean, dry CO test gas by a trained
service engineer.

14
10. Recognizing Nuisance Alarms
Carbon Monoxide (CO) Nuisance
RESET: Pushing the test / reset button during CO alarm allows the unit to reset calculations and double check
for the presence of CO. If the unit re-alarms , it is sensing high levels of CO which can quickly become a
dangerous situation. Move to fresh air and call 0800 111 999.
WARNING: IT IS IMPOSSIBLE TO DETERMINE THE SOURCE OF A CO ALARM USING SIGHT OR
SMELL. ALWAYS CONSIDER A CO ALARM EVENT AS DANGEROUS.

15
11. Battery
This alarm is powered by two AA batteries. Under normal operating conditions, the batteries will last a mini-
mum of one year. NOTE: Constant exposures to extreme temperatures and humidities may aect battery life.
WARNING: DO NOT ATTEMPT TO OPEN THE ALARM FOR ANY REASON! DO NOT TRY TO
REPAIR THE ALARM YOURSELF.
Low Battery
This alarm is equipped with a low battery monitor circuit. If the battery capacity is nearing the point where it
can no longer provide adequate power for all alarm functions, the low battery condition will occur. See Trou-
bleshooting Guide. The batteries must be replaced within 30 days of the rst occurrence of the “Low Battery
Warning” to provide continuous alarm detection.
Replace battery
These batteries can be purchased from your local retailer.
WARNING! Alarm will not attach to back-plate unless batteries are installed. Depleted or removed
batteries will render this alarm inoperative.
Chirping:
When End of Unit Life or Low Battery chirping begins, you can temporarily silence these chirps by pressing
the test button. See Troubleshooting Guide.
Recommended Batteries.
Duracell MN1500, MX1500
Gold Peak 15A
Golden Power GLR6A
Energizer E91
Slide alarm from back-plate.
Insert 2 x replacement ‘AA’ batteries
(noting polarity – see sketch)
Replace back-plate and test the alarm
NOTE: Do not use Lithium
batteries in this unit.
WARNING: Replace unit immediately after End of Unit Life. It will not detect CO in this condition.

16
12. General Carbon Monoxide (CO) Information
What is Carbon Monoxide?
Carbon monoxide (CO) is a highly poisonous gas with no taste, colour or smell.
Carbon monoxide is a cumulative poison. Long term exposure to low levels may cause symptoms.
This alarm is time-weighted – the higher the level of CO, the sooner it will alarm.
NOTE: The apparatus may respond to brief exhaust gas emissions, for example during the initial start-up of an
appliance. Also, hydrogen acts as an interferent and can arise from some battery charging activities and the
curing of concrete or cement under certain circumstances. Volatile Organic Compounds (VOCs), e.g. alcohols,
which may eventually activate the alarm, can be generated from use of damp-proofing materials or other
coatings containing alkylalkoxysilanes.
Potential Sources of CO This CO alarm is not a substitute for proper installation,
use and maintenance of fuel burning appliances
including appropriate ventilation and exhaust systems.
Carbon monoxide can be produced from poorly burn-
ing appliances or from blocked flues and chimneys.
If your alarm has sounded and you have ventilated the
room, the CO may have dispersed before help arrives.
It is crucial that the source of CO is determined and
appropriate maintenance carried out.

17
The table below shows the effects of different levels of CO poisoning on the
body;
WARNING: The device cannot warn against the chronic effects of exposure to carbon monoxide or protect
individuals who are at specific risk.
NOTE: If you recognise any of the above symptoms consult your Doctor immediately.
NOTE: Young children, elderly and pets are more susceptible to the dangers of CO.
NOTE:
Your Kidde alarm is designed to detect CO gas. It is not designed to detect other gas such as natural gas.
NOTE: This product is intended for use in ordinary family homes. It is not designed to measure compliance with
occupational safety and the HSE.
NOTE: Individuals with certain specific medical conditions may need an alarm that operates below 30ppm. If
this applies consult your Doctor.
IMPORTANT: Ensure that all family members are familiar with the symptoms of CO poisoning and how your
alarm works.
To be safe, know the possible sources of CO in your home. Keep fuel burning appliances and their chimneys
and vents in good working condition. Learn the early symptoms of exposure, and if you suspect CO poisoning,
move outside to fresh air and get emergency help. Your first line of defence is an annual inspection and regular
maintenance of your appliances. Contact a licensed contractor or call your local utility company for assistance.
In rented properties your Landlord (or Council/ Housing Association), will have an Emergency Response
phone number, and be liable for the regular maintenance of their combustion appliances (Gas/LPG/Oil/
Solid Fuel).
PParts per Million (PPM)
of CO
TiEffects on Adults
100 Slight headache, nausea, fatigue (flu-like symptoms)
200 Dizziness and headache within 2 – 3 hours
400 Nausea, frontal headache, drowsiness, confusion and rapid heart rate. Risk to life after
over 3 hours of exposure
800 Severe headaches, convulsions, vital organ failures. Death possible within 2 – 3 hours

18
13. Cleaning Your Alarm
Your Alarm Should be Cleaned at Least Once a Year
You can clean the interior of your alarm by using compressed air or a vacuum cleaner hose and blowing or
vacuuming through the openings around the perimeter of the alarm. The outside of the alarm can be wiped
with a damp cloth. Use only water to dampen the cloth, use of detergents or cleaners could damage the alarm.
If the alarm is in Fault mode, the alarm may be in need of cleaning. After cleaning, press the test button. If the
fault does not clear, the alarm needs to be replaced.
•Never use detergent or other solvents to clean the unit.
•Avoid spraying air freshener, hair spray, or other aerosols near the alarm.
•Do not paint the unit. Paint will seal the vents and interfere with the sensor’s ability to detect CO.
•Keep away from nappy buckets.
•Never attempt to disassemble the unit to clean inside. Altering the alarm in any way may lead to a risk of
electric shock or prevent it from functioning correctly. This action will void your warranty.
•The following substances can aect the CO sensor and may cause false readings and damage to the sen-
sor: Methane, propane, isobutane, iso-propanol, ethyl acetate, hydrogen sulde, sulde dioxides, alcohol
based products, paints, thinner, solvents, adhesives, hair spray, aftershave, perfume, and some cleaning
agents.
NOTE: there could be other compounds occurring within a particular household which could cause similar
eects.
•Move the Alarm and place in another location prior to performing any of the following:
Staining or stripping wood oors or furniture
Painting
Wall papering
Using adhesives
Storing the unit in a plastic bag during any of the above projects will protect the sensors from damage. When
household cleaning supplies or similar contaminates are used, the area must be well ventilated.
WARNING: REINSTALL THE ALARM AS SOON AS POSSIBLE TO ENSURE CONTINUOUS
DETECTION.

19
14. Service and Warranty
Seven-Year Limited Warranty
KIDDE SAFETY EUROPE LTD warrants to the original purchaser that the enclosed alarm (batteries excluded) will
be free from defects in material and workmanship or design under normal use and service for a period of seven
years from the date of purchase. The obligation of KIDDE SAFETY EUROPE LTD under this warranty is limited to
repairing or replacing the alarm or any part which we find to be defective in material, workmanship or design
(part replacement only, no installation), free of charge
to the customer, upon sending the alarm with proof of
date of purchase, postage and return postage prepaid, to distributor:
Warranty Service Department, Kidde Safety
Europe Ltd, Ash House, Littleton Road, Ashford, TW15 1TZ, UK. Before shipping, please remove the batteries
from the alarm.
This warranty shall not apply to the alarm if it has been damaged, modified, abused or altered after the date of
purchase or if it fails to operate due to improper maintenance or inadequate A.C. or D.C. electrical power.
THE LIABILITY OF KIDDE SAFETY EUROPE LTD OR ANY OF ITS PARENT OR SUBSIDIARY CORPORATIONS ARISING
FROM THE SALE OF THIS ALARM OR UNDER THE TERMS OF THIS LIMITED WARRANTY SHALL NOT IN ANY CASE
EXCEED THE COST OF REPLACEMENT OF THE ALARM AND, IN NO CASE, SHALL KIDDE SAFETY EUROPE LTD
OR ANY OF ITS PARENT OR SUBSIDIARY CORPORATIONS BE LIABLE FOR CONSEQUENTIAL LOSS OR DAMAGES
RESULTING FROM THE FAILURE OF THE ALARM OR FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS
OR IMPLIED, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE COMPANY’S NEGLIGENCE OR FAULT.
This warranty does not affect your statutory rights.

20
Quick Start Instructions
1
3
2
Model: K5CO
MODEL: K5CO
Alarm
Move to
Fresh Air
Operate Fault
Carbon MonoxideAlarm
20
Quick Start Instructions
1
3
2
Model: K5CO
T
E
S
T
/
R
E
S
E
T
MODEL: K5CO
Alarm
Move to
Fresh Air
Operate Fault
CarbonMonoxide Alarm
T
E
S
T
W
E
E
K
L
Y
/
R
E
S
E
T