KIDPRO Safety Net for Children User manual

CONTENTS
The net: 1 linear meter contains 14 rhombuses
Screws and pegs: 5 pairs per anchor strip
Anchor strips: lenght 1m, 14 hooks per anchor strip
!
SAFETY NET FOR CHILDREN
KIDPRO, Ivan Pejic s.p.
Safety nets for windows and balconies
Binkelj 38, 4220 Skofja Loka, Slovenia - EU
T: 00 386 40 565 993
E: [email protected], I: www.kidpro.eu
INSTALLATION MANUAL
This product provides additional protection from accidental
fall (for windows, balconies, terraces, stairs, mezznines)
and it has been undergone thorough tests by Institute for
industrial technology INTI - Argentina, TÜV Rheinland® -
Argentina and AIDICO - Spain.
2
SAFETY PRECAUTIONS
1. Always use safety equipment during installation
process on hight.
2. Make sure the place you are attaching the safety
harness to is able to safely hold it.
3. Do not install the safety net in wet weather.
4. Check if the tools, cables and electrical plugs and
sockets are in good condition.
5. Wear protective shoes and safety glasses as well as
noise protection headphones.
6. Mark and protect the area on the ground below the
window or balcony, where the installation will take
place and make sure there is no one within the area.
Attention! Falling tools danger!
7. Do not modify and/or incorporate additional parts to
the product. Do not install accessories, spare parts
or components other than those provided in the
package.
8. The complete installation should be done from inside
the building. Make sure that all installation areas are
accessible from the inside. Attention! Falling from
hight danger!
9. Make sure that the walls ment to support the net
are in good condition and able to rmly hold the
ancorage. For gyprock, drywall/plasterboard please
use appropriate dowels (Gips-Fixx). You may also use
aluminum frame to hold the anchorage.
10. Make sure you choose the right type of screws for
the surface material where the anchorage is to be
mounted.
11. If there is a blind, the net should be installed on the
outer side of it and you should verify that once the
net is installed, the outside stops of the blind do not
tear the net when rolling the blind up or down.
12. Do not install the net that is damaged or older than
expected lifetime.
13. The safety net must always be installed vertically.
Read carefully!
1. Read entire installation manual before installing the
product. Make sure that you clearly understand it
and that you are able to install the product correctly
according to this manual.
2. In case you are not sure if you can correctly install the
netting system following the manual, please contact
us.
3. Do not alow anyone to install the product without
reading this manual.
4. Remove and dispose all plastic bags and packaging
elements possibly hazardous to children.
Attention! Choking hazard!
5. Do not allow children close to the installation area.

1. ATTACH THE ANCHOR STRIPS
1. Carefully measure all sides of the opening to be
protected with the net and calculate the number of the
anchor strips needed for every side.
2. Make sure that the hooks are evenly distributed (7 cm)
along the anchor strip. The rst and last hook should be
placed 3.5 cm from the edge. 1
3. Hooks can be moved by applying slight pressure
towards the anchor strip. To remove or place the hook
on the anchor strip, rotate it by 90 degrees. 2
4. After distributing the hooks evenly, mark the places on
the anchor strip where the holes for the screws will be
drilled. Each anchor strip should be attached with the 5
screws to the base. Place the holes every 25 cm: two at
the end, one in the middle and two in between. Drill the
holes for the screws using the 4mm drill bit. 3
5. Place the anchor strip on the base and mark the
position of the holes on the base.
6. Drill the holes in the base. Depending on the type of
base, use 6mm drill bit for concrete or 3mm drill bit for
wood and metal. If applicable, put the dowels into the
holes. Attach the anchor strip using appropriate screws.
4
7. Cut the last anchor strip with a small saw for metal to
adjust its length to the remaining space on the base.
8. Use anchor strips to entirely cover all sides of the
opening.
2. PLACE THE NET
When all anchor strips are mounted, start placing the
net. Only use hands. Sharp objects can damage
the net.
1. Hook the net in one of upper corners. Hook entire top
side. Hook left and right side from the top downwards.
Hook bottom side from the corners towards center. 5
2. First rhombus is hooked onto two anchors (top and left
/ top and right). 6
3. When this is done, check if the net is attached to all
anchors / hooks.
4. Check the tension of the net pushing it mildly with
palms. It should have right tension: not too tight, not
too lose. If needed, make little adjustments by moving
the hooks slightly along the anchor strip.
3. CUT THE EXCESS OF THE NET
1. Provided the net is properly mounted and tensed and
entirely attached, use scissors to cut the excess of net.
ATTENTION! It is only allowed to cut the loose end of
the net, on the outer side of anchor strips. Do this with
caution, ensuring to leave the knots intact. 6
2. Congratulations! If you carefully followed the
instructions, your net is installed correctly!
INSTALLATION MANUAL
1
2
4
3
6
5