Kimberly-Clark PROFESSIONAL SCOTT PRO User manual

1034135 • 9/2019
Installation instructions for the KIMBERLY-CLARK PROFESSIONAL™SCOTT®PRO
STAINLESS STEEL RECESSED DISPENSING SYSTEMS Code: 31501
IMPORTANT! For secure mounting, follow instructions thoroughly.
Door
Back Housing
Instructions
Trim Ring
Silver Core Plug
Black Swing Arm Plugs
Key
Retaining Clips
(1) (3) (2)
A
B
C
E
D
F
G
H
A
B
E
GC D
F H
These instructions are for installation
with studs on 16” centers. Rough Wall Opening:
• 11 1/8” Wide
• 15 3/8” High
• 4” Min. Depth

2034135 • 9/2019
Installing the Stainless Steel Unit, Recessed in Wall - 31501
Materials Required:
• Manual or electronic module
• Tape measure
• Combination Square
• Screw Driver
• Rotary Cutter
• Right angle mirror
• Installation screws (4 – 2” 8 gauge)
• Installation screws (4 – 2.5” 8 gauge)
• Stud finder
• Flash light
• (2) 2 x 4” ’s for framing
• (2) 1 x 4” ’s for framing
• Hammer
• File
• Level
• 4 Shims (may or may not be needed)
Note: This unit is for an install with studs on 16 inch centers or less.
1. Determine the location to mount the
dispenser using a stud finder and mark
the rough wall opening. (Figure 1 & 2)
2. Note that it is important to install the
dispenser 12 inches above the counter
or other obstruction. Please consider
this when deciding where to install
the dispenser. (Figure 3)
3. While measuring an installation location,
note that the doors can be reversed.
However, the door is set to open right
to left. Ensure that you have adequate
space to open the door in the area
chosen. You will need a minimum of
8 inches of clearance. (Figure 4)
4. Cut an investigation hole to ensure that
there is not plumbing, electric, etc. in the
install area and use a flash light or right
angle mirror to check the area. (Figure 5)
5. The first cut for the install should be 12
inches from a counter and to be ADA
compliant, the opening of the dispenser
should be 48 inches from the floor.
(Figure 6)
6. Now mark the rough wall opening
and begin the cut. Ensure that you
are at least 12 inches from the top
of the counter. (Figure 7)
11.125”
15.375”
12” 6”
1
4 5
3
2
6 7
48”
12”
Floor
Countertop 12”
15.375”
11.125”

3034135 • 9/2019
7. Test the fit of the dispenser in the hole.
(Figure 8)
8. Determine if additional framing is
needed for the install. For jobs on 16
inch centers, additional framing will be
needed. Use 2 x 4” ‘s and 1 x 4” ‘s and
balance the framing on each side as
needed. (Figure 9 & 10)
9. Measure the fit to the dispenser again
to ensure that the fit will be right. Shims
may be needed at this point. (Figure 11)
10. Install dispenser using 4 screws in the
side of the housing attaching to the studs
in the wall. Before adding screws, check
to see that the unit is level. Add 2 screws
on the top side and two on the bottom
side of the housing. Do not overtighten.
(Figure 12 & 13)
11. Insert the module by lining it up with the
guides on the back housing and push
down gently to click the module in place.
For detailed instructions see the video
on installing the module and loading the
paper. The module is sold separately.
12. Add the operating label that comes with
the module to the inside of the door, then
install the door. The swing arm is taped
to the back housing, remove tape and
install the swing arm by using the black
plug that came with the dispenser into
the cover. This prevents the door from
sagging. (Figure 14 & 15)
8
9 10
11
13
12
14
15

4034135 • 9/2019
16
034026
Automatic
PlaceHandBeneathTearAcross
13. Add the retaining rings commonly known
as “c” clips on the hinges for the door to
keep the cover in place. (Figure 16 & 17)
14. Close the door. (Figure 18)
15. Add the use label that comes with
the dispenser, it is now ready to use.
(Figure 19)
17
19
16
18