Kinderkraft JUNIOR FIX 2 i-Size User manual

MODEL: I-GUARD ECE.R129.03 ver. 1.2
JUNIOR FIX 2
i-Size
USER GUIDE
MODEL: JUNIOR FIX 2 i-Size ECE R129.03 v.2.0

2
NOTE! Product graphics serve an illustrative function!
1.0 Usage
The car seat has been designed, tested and approved for use in
accordance with the requirements of UN/ECE Regulation No. 129
concerning the approval of child restraint systems (UN/ECE R129/03).
Do not set the car seat in a forward facing position until your child is 15
months old and 76 cm tall.
The car seat can be installed in the car in places indicated by the
manufacturer in the vehicle manual. It is required to read the vehicle
manufacturer's operating instructions.
To ensure proper installation, please refer to the table on the next page.

3
Hight of the child
Car seat setting
Car seat mounting
100-150cm
ISOFIX + three-point car seat belt
Three-point car seat belt

4
2.0 Safety instructions
Please take a few minutes to read this instruction manual in order to
ensure the proper safety of your child.
• The car seat MUST NOT be installed on the vehicle seats
mounted backwards or sideways.
• The car seat MUST NOT be placed on the vehicle seats
with an active front air-bag.
• The car seat can only be installed on the vehicle seat
with a three-point car seat belt.
• It is recommended to install the car seat on the vehicle
back seats only.

5
Information on the suitability of the car seat for use with a child seat can be
found in the vehicle's operating instructions.
•Make sure that the inner harness straps holding your child are suitable for
your child's build and are not twisted. Therefore, do not place thick clothing
under the child's belt.
•The lap straps of the seat belt must run as low as possible over your child's
pelvis to ensure optimum effect in the event of an accident.
•The seat must be replaced if it has been subjected to heavy loads in a road
accident.
•The car seat must not be modified in any way without the authorisation of
the relevant approval authority. If the seat is not installed in accordance with
the manufacturer's instructions, this may endanger life and health.
•Protect the child car seat from direct sunlight, otherwise your child may burn
themselves on the heated parts. Protect your child and the child seat from
direct sunlight.
•Never leave a child unattended in a child seat.
•Make sure that luggage and other objects are adequately secured,
especially on the shelf under the rear window, as they can cause injuries
in the event of a collision.
•The seat must not be used without the cover.
•Do not use any replacement cover other than that recommended by the
manufacturer, as it is an essential part of the seat's safety system.
•Do not use any attachment points other than those described in the
instructions and labelled on the seat.
•All hard parts and plastic parts of the child seat must be positioned and
installed in such a way that they cannot be pinched by the sliding seat or
the vehicle door under normal conditions of use.
•Check the condition of the seat regularly, paying particular attention to
the attachment points, seams and adjustment parts. Make sure that all
mechanical parts are fully functional. Never lubricate or oil components of
the child seat.

6
•Do not use the seat if parts are damaged or loose.
•In an emergency, it is important to release the harness quickly. This means
that the button for releasing the harness is not fully secured.
•Set a good example for your child and always buckle up. An adult who is not
buckled up can also pose a danger to a child.
•Make sure the seat is properly secured before every car journey.
•The seat should also be secured when it is not in use. An unsecured child seat
can also cause injury to the occupants in the event of emergency braking.
•On some car seats made of sensitive materials, the use of the car seat
can leave marks and/or cause discolouration. To prevent this, you can
place a blanket, towel or similar product under the car seat.

7
A: Backrest latches
B: Fasteners
3.0 Installing the car seat backrest
1. Place the backrest flat behind the seat and hook the bottom of the
backrest onto the seat
2. Adjust the backrest until it locks in the vertical position. You will hear a
characteristic "click" sound
3. Cover the inside of the car seat by fastening the fasteners on the
backrest
Note! When rotating the backrest, check whether there are
no obstacles in the area of the connector between the
backrest and the seat.

8
4.0 Adjusting the backrest and securing the
child
The backrest of the car seat is movable, thanks to which it is possible to
adjust it accurately to the plane of the vehicle seat.
Tilt the backrest backwards until it is adjacent to the vehicle
seat.
IMPORTANT! Make sure there are no gaps between the car
seat and the vehicle seat.
IMPORTANT! To ensure your child's comfort, move the front
vehicle seat as far forward as possible to provide room for
your child's legs.

9
A: Headrest height adjustment lever
B: Headrest
4.1 Height of the headrest
1. Grasp the headrest adjustment lever located on the back of the
headrest and pull it gently upwards
2. Adjust the headrest by selecting one of ten options and when the
height is adjusted, release the adjustment strap
IMPORTANT! Make sure the vehicle seat headrest is locked in
place
The headrest should fit snugly around your child's head, with
the lower part of the headrest at the same height as your
child's shoulders.

10
4.2 ISOFIX installation
1. Place the car seat on the vehicle seat. Press both sides of the ISOFIX
release button and extend the ISOFIX connector arms to their maximum
length.
2. Grasp the car seat with both hands and insert both latches into the
places of installation on the vehicle seat. When you hear a "click" of each
of the ISOFIX latches, push the seat of the car seat against the backrest of
the vehicle seat, exerting firm even pressure on both sides.
NOTE! The locking latches are properly attached only when both button
indicators are completely green.
Pay attention to the audible clicking sound of the ISOFIX
connectors and grasp the car seat to check whether it is
securely installed without any play. If it moves and the ISOFIX
latches come out, repeat the previous steps.

11
A: Shoulder belt guide
B: Waist belt guide
5.0 Children between 100 and 150 cm - using
ISOFIX connectors and three-point car seat
belt.
1. Install the car seat on the vehicle seat using ISOFIX connectors.
2. Push the car seat all the way into the seat and check its correct
installation –the colour of the indicators should change to green.
3. Place your child in the car seat
4. Adjust the headrest to their height
5. Guide the shoulder belt through the green guide of the shoulder belt.
6. Guide the car seat belt through both waist belt guides. Fasten the car
seat belt. You will hear a characteristic "click".

12
A: Shoulder belt guide
B: Waist belt guide
5.1 Children between 100 and 150 cm - using
three-point car seat belt.
1. Install the car seat on the vehicle seat.
2. Push the car seat all the way to the vehicle seat.
3. Place your child in the car seat
4. Adjust the headrest to the child's height
5. Guide the shoulder belt through the green guide of the shoulder belt.
6. Guide the car seat belt through both waist belt guides. Fasten the car
seat belt. You will hear a characteristic "click".

13
A: ISOFIX release button
B: ISOFIX arm
6.0 Uninstalling the car seat (ISOFIX installing
system)
1. Press the release button on both ISOFIX latches. (The latches will be
released, and the colour of the ISOFIX indicators will change from green to
red)
2. Insert the ISOFIX arms into the base of the car seat using the sliding
lever.

14
A: Fasteners
B: Backrest latches
6.1 Removing the car seat backrest
1. Uncover the inside of the car seat by unfastening the fasteners located
on the backrest.
2. Push the backrest away from you so that the car seat's backrest lies flat
on the surface.
3. Detach the backrest by pulling it out of the latches.

15
A: Fastener
B: Waist belt guide
7.0 Removing the cover
1. Unfasten the fasteners located on the edges of the car seat backrest
material, then uncover the car seat cover by moving the material from the
backrest to the headrest
2. Unfasten the fasteners located on the edges of the cover (on both
sides)
3. Unfasten the fasteners located at the back of the car seat holding the
material on the sides of the car seat.
4. Starting from the bottom, slide the material off the sides of the car
seat.
5. Unfasten the fasteners located at the back of the car seat holding the
material on the seat
6. Gently pulling on the material, slide it off the waist safety harness
guides on both sides.

16
7. Pull the material towards you to slide it off the seat.
8. Starting from the sides of the headrest, slide it off the shell of the car
seat.
7.1 Installing the cover
To put the cover back on - just reverse the above sequence of actions.
Align the cover with the attachment points on the car seat. Start by
installing the cover on the shell of the car seat and finally on the headrest
part.

17
8.0 Cleaning
NOTE! The car seat must not be used without the cover.
• The cover is removable and washable with a mild powder and using a
program for delicate fabrics (30°C).
•Follow the washing instructions on the cover information label. The
colours may fade if it is washed at the temperature above 30°C.
The cover should not be centrifuged or dried in a tumble dryer (which may
lead to separation of the material layers).
• Prolonged sun exposure of the cover is prohibited.
• Plastic parts can be cleaned with soap and water.
• Do not use aggressive cleaning agents (such as solvents).
• The safety harness can be cleaned in lukewarm soapy water.
Warning! You must not remove the metal clips from the safety harness.
The full text of the Warranty Terms and Conditions is available on the
website WWW.KINDERKRAFT.COM

18