kinetic T-006 Cyclone User manual

5280 Main Street NE Minneapolis, MN 55421
1.877.226.7824 | www.kurtkinetic.com
CYCLONE
ASSEMBLY MANUAL
T-006C
MODEL

www.kurtkinetic.com | 1.877.226.7824
Page 2
COMPONENTS
Part A
Folding
Frame
Tools Required for Assembly: 14mm Wrench, 4mm Hex Key
When unpacking, check that the following components are present:
Part B
Resistance
Unit
Your Kinetic Trainer is designed for use with road, mountain, BMX and
recumbent bikes. Before adjusting these legs, you must know your
bike’s tire size, which is printed on the sidewall of every tire.
When shipped from the factory, the folding leg is mounted in Position
1 on the main frame and will function with all tire sizes. However, to
lower the drive wheel and maintain good riding position it is best to
adjust the leg position to match your tire size. Ideally, your rear tire
should be approximately 1-1/2” from the oor. Use the chart shown
here to determine the recommended leg position.
The appropriate leg position may vary for some wheel diameters
because of tire thickness. Choose the setting that positions the bike as
level as possible.
Part C
L-Bolt
Part F
Mounting
Bolt and
Nut
Part E
Adjustment
Knob and
Washer
Part M
Skewer
Part D
Spring
ADJUSTABLE FOLDING LEGS
1
2
43
PLEASE NOTE:
If any of the
components
listed are
missing, please
call our Customer
Service hotline at
877-226-7824.
Part B
Resistance
Unit
ROLLER
FLY
WHEELS
YOKE
Because we
test each
trainer there
will be tire
marks on the
roller.
SERIAL
NUMBER
Part N
Small Cone
Cup
(Installed on trainer)
Part K
Small Cone Cup
Skewer Adapter
(see www.kurtkinetic.com for installation instructions)
FRAME
POSITION position 1 position 2 position 3 position 4
MAXIMUN
TIRE SIZE 700c / 29” 650c 24” 20”
Use two wrenches to remove the nut.
Remove bolt. Select appropriate hole
and reinsert bolt through frame and leg.
Attach nut and tighten securely until
some resistance is felt in the movement
of the folding leg. Repeat with other side.

www.kurtkinetic.com | 1.877.226.7824
Page 3
QUICK
RELEASE
LEVER
LOCK RING
RISER RING
LEG BOLT
ADJUSTMENT KNOB
FLYWHEEL
RESISTANCE UNIT
TRAINER DETAILS
TENSIONING
KNOB

www.kurtkinetic.com | 1.877.226.7824
Page 4
1
2
ATTACH RESISTANCE UNIT
PART F
PART C
Fasten resistance
unit with mounting
bolt and nut
Place L-Bolt in frame
sleeve as shown

www.kurtkinetic.com | 1.877.226.7824
Page 5
3
4
ATTACH RESISTANCE UNIT
PART D
PART E
Slide spring over
L-Bolt
Tilt the resistance
unit up toward
the frame while
directing L-bolt into
the hole in the yoke.
Attach adjustment
knob and washer.

www.kurtkinetic.com | 1.877.226.7824
Page 6
MOUNTING BIKE
1
2
Loosen lock
ring and
Turn knob to
center bike
QUICK
RELEASE
Push knob
tight against
skewer, close
quick release
and tighten
knob until tire
is centered
on roller 3
Tighten knob on
quick release side
of trainer until wheel
is rmly centered
on resistance unit
roller
RIGHT SIDE
Grip frame
at seat stay
At this point,
be sure that
resistance
unit is loosely
tightened and
does not touch
tire.

www.kurtkinetic.com | 1.877.226.7824
Page 7
MOUNTING BIKE
5
4
Tighten lock
ring when wheel
is centered on
resistance unit and
bike is rmly locked
in at the skewer
Turn adjustment
knob until roller
touches tire. then
add 2 to 5 more
turns.
test tire friction by
sharply moving
tire a 1/4 turn back
and forth. apply
another 1/2 turn on
adjustment knob if
needed.
KINETIC SKEWER
(included with trainer)
*FOR YOUR SAFETY
We recommend using the skewer that was included with your trainer.
RECOMMENDED SKEWER AND CONE COMBINATION*
PART M
PART N
BIKE REMOVAL
To properly remove the bike:
1. Turn the adjustment knob
on the resistance unit
counterclockwise to back the
roller away from the tire until it
is no longer touches.
2. Reduce axle tension by
turning the right axle knob
counterclockwise, a minimum
of two turns, to allow for
disengagement of the quick
release.
3. Firmly grasp your bike seat to
stabilize the bike.
4. Disengage the quick release
on the right side of the trainer
and slide the axle knob to the
fully open position. The bike
can now be removed from the
left cone cup.
LEFT SIDE

Page 8
WARRANTY
CRASH REPLACEMENT POLICYCAUTION
CARING FOR YOUR TRAINER
»Do not over-tighten the adjustment knob (Part E). Over-
tightening will cause both tire and unit damage. Tighten only
enough to avoid tire slippage.
»When using the trainer for normal use or for extended periods
of time, the resistance unit will get hot. DO NOT touch the
resistance unit while it is in use or while it is hot.
»Always consult a doctor before beginning any exercise routine
or using any exercise or tness product including the Kinetic
Trainer. Should you become ill, feel dizzy, light-headed or
nauseous while riding the trainer, stop riding immediately and
seek medical attention.
»While in use, the wheel of your bike and the resistance
unit may be spinning at high speeds. For this reason keep
children, pets and all items safely away from your trainer
while in use. Also be sure that your bike is correctly installed
and securely locked into the trainer before riding.
»Always use the trainer on a at surface.
»In order to keep from tipping the trainer over, be careful not to
lean too far side to side on the Rock and Roll trainer.
By purchasing the Kinetic Trainer you’ve made an investment in a top-quality piece of
equipment. When used according to the manufacturer’s instructions and cared for with
common sense, your Kinetic trainer will provide a lifetime of training. Store the trainer
indoors, out of the rain and away from temperature extremes. Since sweat is corrosive,
you can extend the life of your trainer by wiping it o after your workout.
Kinetic by Kurt oers the original owner a lifetime warranty against
manufacturing defects and/or normal wear and tear for both the trainer frame
and the resistance unit. This warranty is not applicable to damage caused by
misuse, abuse, neglect, accident or unauthorized modication of materials or
parts. If the unit is disassembled by the consumer, this warranty is void. There
are no other warranties, expressed or implied.
It is the responsibility of the purchaser to le a warranty card via mail
or on-line with Kinetic in the event that repairs are needed. It is also the
responsibility of the purchaser to retain receipts for proof of purchase in the
event that repairs are needed. No warranty repairs will be accepted without
the warranty registration and the serial number of the trainer located on the
resistance unit.
WARRANTY CARD/PRODUCT REGISTRATION
Please complete the warranty card with the information requested and return
it to Kinetic within 30 days of purchase. You can also go to www.kurtkinetic.
com and ll out the warranty information online.
WARRANTY CLAIMS/REPLACEMENT PARTS
If you experience problems with your trainer, please call our Customer Service
Hotline at 877-226-7824 or email us at [e-mail]. To help us
handle your call as eciently as possible, please have your trainer’s serial
number ready to give to the customer service representative.
After determining what repairs or replacement parts may be needed, you will
be provided with a Return Material Authorization Number and procedures for
returning your product to Kinetic.
In some cases replacement parts may be shipped directly to you, depending
on the nature of the problem. No product returns will be accepted without a
Return Material Authorization Number.
Kinetic trainers come with a lifetime warranty on the frame and the resistance
unit to the original owner.
However, we understand that accidents can happen involving our products,
so we also oer a crash replacement policy for incidents not covered by our
lifetime warranty. Here is how it works: Kinetic will replace any part or parts
on your Kinetic Trainer that are damaged due to an accident, regardless of the
cause of that accident, and within reason for a $50.00 cost plus the cost of
parts and shipping charges.
We reserve the right to reject any product that has been so severely
damaged that it cannot be rebuilt. To be eligible, you must complete the
warranty registration process by mail or online. Crash replacement repairs
require warranty information and the serial number of your unit. This crash
replacement policy and its related charge may be subject to change without
notice.
To process a claim, please call our Customer Service Hotline at 877-226-7824
or email us at kineticbyk[email protected]. You will be provided a Return Material
Authorization number and you will be given instructions for returning the
product to us. In some cases replacement parts may be shipped to you. No
product returns will be accepted without an RMA number.
Record the Serial Number of Your Kinetic Trainer Here
5280 Main Street NE Minneapolis, MN 55421
1.877.226.7824 | www.kurtkinetic.com