Kinetico Premier Plus User manual

visit www.kinetico.eu
Installation and User Manual
Installation et Guide d’utilisation
Manual de instalación y de usuario
Water Softener
Adoucisseur d’eau / Descalcificador
ENG FR
PREMIER PLUS
ES

Kinetico Premier Plus Water Softener Installation and User Manual
2
For more information about Kinetico:
Pour plus de renseignements sur Kinetico :
Para obtener más información sobre Kinetico:
visit www.kinetico.eu

www.kinetico.eu
3
Original Version
Contents
Safety information 4
Contents of box 6
Specifications 6
How to set the XP 7
Getting to know the softener 9
Pre-installation check list 10
Installation instructions 12
Review 14
Commissioning instructions 15
Useful information 16
Sommaire
Informations de sécurité 18
Contenu de la boîte 20
Caractéristiques 20
Comment régler la dureté (système XP) 21
Se familiariser avec l’adoucisseur 23
Vérifications préalables 24
Instructions d’installation 26
Inspection 28
Instructions de mise en service 29
Informations utiles 30
ENG
FR
ES Contenido
Información de seguridad 32
Contenido de la caja 34
Especificaciones 34
Como ajustar el regulador XP 35
Primeros pasos con el descalcificador 37
Lista de comprobación previa a la instalación 38
Instrucciones de instalación 40
Revisión 42
Instrucciones de puesta en marcha 43
Información útil 44

Kinetico Premier Plus Water Softener Installation and User Manual
4
Safety information
Read all information carefully prior to installing and using the
water softener.
Qualified Installer
Kinetico recommends that a qualified
installer performs the installation. Failure
to install the system as instructed could
invalidate the Limited Warranty.
Water Temperature
Do not install the Kinetico softener in
an area where the water temperature
can exceed 49°C or cause the unit
to freeze. Freezing temperatures will
damage the system.
Water Pressure
Do not install if the supply water pressure
exceeds 6 BAR (87 psi), unless a suitable
pressure regulating valve has been
installed on the softener water supply.
Overflow
VERY IMPORTANT:
Where a cabinet overflow could cause
damage, you must install a 1/2” I.D.
hose to the barbed fitting on the
cabinet and run to a suitable outlet
that is visible and capable of taking the
overflow (i.e. through the outside wall).
Make sure the hose does not go higher
than the barbed fitting as the water
will flow away using gravity.
INSTALLER
1
2
34
5
6
0bar

www.kinetico.eu
5
Original Version
Copper/Plastic Pipework
Where copper/plastic pipework is
used, Kinetico advises adherence to
the regulatory requirements to ensure
adequate earth bonding is provided.
Intended Use
Not intended to be used for treating
water that is micro-biologically unsafe
or water that has an unknown quality,
without adequate disinfection before or
after the system.
Conform to Regulations
You must ensure that the installation
conforms to local plumbing codes and
regulations.
Plumbing Schematic
Please refer to the plumbing schematic
on page 10 before commencing an
installation.
1
2
34
5
6
0bar

Kinetico Premier Plus Water Softener Installation and User Manual
6
Contents of box
Identify the following parts before proceeding.
Meter Disc A B C D E F G H I * J * K * L * M *
PPM 207 221 238 256 279 305 337 376 426 456 490 531 578 635 686 770 878 1020
˚f 21 22 24 26 28 30 34 38 43 46 49 53 58 64 69 77 88 102
˚D 12 12 13 14 16 17 19 21 24 26 27 30 32 36 38 43 49 57
Litres between
regenerations 1583 1480 1377 1274 1171 1068 965 862 759 708 656 605 553 502 450 399 347 224
Cabinet dimensions (h x w x d) 645 x 480 x 396 mm
Salt used per regeneration 0.56 kg
Regeneration time 11 minutes
Flow rate @ 1 bar pressure drop 22.7 l/min
Pipe connections - in/out ¾” BSP
Min/max operating pressure 1.8 - 6 bar
Min/max operating temperature 2 - 49˚C
Specifications
Max
hardness
1 x in/out retaining
bracket and pin
4 x o-ring
1 x 2cc silicone tube 2 x 3/4” washers 2 x 3/4” BSP in/out adaptor
By-pass valve
(included with the Premier Plus HE ALT BP only)

www.kinetico.eu
7
Original Version
How to set the XP
Unlock the XP:
Manually initiate a regeneration
until the XP meter is in the home
position. This is identified by the
XP arrow at the 6 o’clock position
on the valve.
1
Select the setting
using the chart:
Determine the XP meter setting
from the chart on previous page:
a: find your unit
b: read across to hardness level
c: read to the top for setting.
For applications containing iron,
use the highest (certified where
applicable) salt dosage.
2
Set the XP meter:
Adjust the XP meter setting by
using a 3/16” or smaller flat-head
screwdriver to push down and
rotate the hardness adjustment
knob.
3

Kinetico Premier Plus Water Softener Installation and User Manual
8
Release the XP
adjuster:
Release adjuster, making sure
knob returns to an up position.
5
Notes:
NEVER set XP with the arrow
aligned anywhere in the black
section of the meter disc. The
softener will not meter properly.
6
Confirm the setting:
Set the arrow to the desired
position. The arrow points to
the centre of the box for whole
figure settings. For 1/2” settings,
the arrow points to the line
between boxes.
4
Set to K in this
example

www.kinetico.eu
9
Original Version
Getting to know the softener
Salt compartment
Top lid
Front lid

Kinetico Premier Plus Water Softener Installation and User Manual
10
Air gap:
Local regulations
must be adhered to
Pre-installation check list
When determining the location of the softener, the following
should be considered:
To home
To drain
Cold water supply
Optional extra:
Pressure regulating
valve
Non-return valve:
Local regulations
must be adhered to
Optional extra:
Non-return valve, local regulations
must be adhered to
Overflow

www.kinetico.eu
11
Original Version
Installation will vary but should consist of:
a: A pressure regulating valve on the water supply to the softener where the
incoming pressure exceeds 6 bar.
b: A non-return valve on the mains water supply to the softener.
c: A by-pass assembly which enables the softener to be isolated from the water
supply for maintenance and service. This also maintains the water supply when
the system is disconnected.
d: A drain line from the softener to a waste pipe through an appropriate air gap.
The drain must comply with local plumbing codes.
e: An overflow run to a suitable outlet that is visible.
Ensure you have the following:
a: Kinetico blending by-pass valve
plus a single check valve.
b: Connections for the inlet and outlet, either by means of flexible pressure rated
hoses or by direct pipework. Connections on the softener and the Kinetico
blending by-pass valve are 3/4” BSP male threaded fittings.
c: 1/2” ID hose for both the overflow and the drain.
Inlet
Outlet
Inlet Only
Or, a means of constructing a by-pass
which consists of:
3 valves, Tee pieces, Single check valve

Kinetico Premier Plus Water Softener Installation and User Manual
12
Installation instructions
Locate:
a: Ensure the unit can be
positioned on a flat surface.
b: If sand, silt or turbidity are
present in the water supply, a
pre-filter should be installed
before the water softener.
1Test water pressure:
Test incoming pressure to the
unit. A pressure regulating valve
will be required if the pressure
is above 6 bar.
2
Install:
Plumb pipework as necessary to
accommodate a by-pass assembly.
3
1
2
34
5
6
0bar

www.kinetico.eu
13
Original Version
Caution: Do not solder any fitting while connected to the unit adaptors.
Care should be taken during the installation process to ensure solder and flux
do not come in contact with any of the components.
Flush:
After plumbing is complete, but
before connecting to water softener,
flush both inlet and outlet lines and
allow water to rinse out any debris.
4
Or, establish a by-pass installation
based on the following diagram. Fit inlet/outlet
connection:
When using the Kinetico blending
by-pass valve, consult separate
installation instructions. Please
note, the orientation of the valve
will determine which connection
is used as the inlet. Or, follow the
process below:
a: Fit 2 o-rings to each in/out
adaptor then lubricate with the
supplied silicone grease.
b: Connect inlet/outlet adapters
to supply and return hoses
remember to use the washers.
c: Install adapters into control
valve in/out ports, ensuring that
they are fitted into the correct
ports (see flow arrows on valve
for reference).
d: Attach the retaining bracket and
pin to the control valve.
5
1
2
34
5
6
0bar
Mains supply To
home
Pre-filter
To water softener
Gauge
Pressure
regulating valve
Non-return valve

Kinetico Premier Plus Water Softener Installation and User Manual
14
Review
By-pass assembly:
Ensure the assembly is in the
“by-pass” position.
5
Pressure:
If a pressure regulating valve
has been fitted, ensure it has been
correctly set to 6 bar maximum.
1
Drain line:
Ensure the drain line is securely
attached, has no restrictions or kinks,
uses an airgap and is fully compliant.
2
Overflow:
Ensure the overflow has no kinks, is
securely attached and that water is
able to fall away with gravity.
3
Inlet/Outlet connections:
Ensure the hoses/plumbing are
attached securely, using the washers
provided, and are firmly held in place
using the retaining bracket and pin.
4
Service PositionBy-pass Position
Run drain line:
a: Run a drain line to a
discharge point, checking for
any obstructions or possible
kinks.
FOLLOW LOCAL PLUMBING
CODES.
b: Push the drain line onto the
barbed fitting and tighten the
jubilee clip securely.
6
Please note:
Drain lines must not run more than
2.4m up or exceed a total of 9m. The
drain line must not be restricted or
kinked.
✗

www.kinetico.eu
15
Original Version
Initiate a backwash:
a: Using a Phillips head screwdriver
push down on the actuator, and
slowly turn CLOCKWISE until the
indicator dot reaches the letters
BW on the clear cap.
b: You will hear a rush of water and
air going to the drain.
c: When the cycle has finished
(approx 4 mins), repeat the
procedure, turn the indicator dot
to the next backwash cycle and
allow to finish (approx 4 mins).
3
Pressurise:
With the water to the property restored, slowly move the assembly to the “in
service” position. Water may run to drain until the unit is fully pressurised.
1
Commissioning instructions
Fill the brine tank
with water:
Allow the brine tank to fill with
water until the brine valve shuts o.
The water level should be
approximately 50mm over the
grid plate.
2
Actuator
Indicator
50mm
Grid plate
Water level

Kinetico Premier Plus Water Softener Installation and User Manual
16
Add salt:
For convenience, the water
softener has been designed
to accommodate tablet/pellet
salt. Simply pour into the salt
compartment.
IMPORTANT:
Only use salt manufactured for
use in water softeners.
Do not load salt behind the
water softener tanks.
Do not use rock or granular salt
in your system. They contain
impurities that can interfere with
performance and could invalidate
the Limited Warranty.
Fit the lid:
Replace the lids and check
plumbing for any leaks. The
installation is now complete.
5
4
Useful
information
How do I correct
the water level if it
sits higher than the
recommended 50mm
above the salt grid?
Check that the brine valve is
seated firmly on the base of the
cabinet.
1
Why am I experiencing
varying levels of
hardness?
The softener will provide soft
water immediately; however, until
mains water has been displaced
from the pipework, storage tanks
and hot water system, you will
experience varying degrees of
hardness.
Depending on your water system
and water usage, this may take a
few weeks
to clear.
It is also advisable to check that
the by-pass valve is closed, when
not using the Kinetico blending
by-pass valve.
2

www.kinetico.eu
17
Original Version
Should water be present in the salt compartment?
Yes, it is normal to see water at a level of 50mm above the salt grid
(see page 15). If water is not present to this level:
a: Fill the salt bay with water until the level is 50mm above the salt grid. Then
conduct a manual regeneration.
b: To manually regenerate using a Phillips head screwdriver push down on
the actuator, and slowly turn CLOCKWISE ONLY until the actuator tab has
advanced the indicator dot to the word “BRINE”.
c: You will hear a rush of water and air going to the drain.
d: When the vessel has finished its cycle (approx 11 mins), repeat the procedure,
advance the indicator dot to the word “BRINE” in the next section and allow
to finish (approx 11 mins).
3
Indicator
Actuator

Kinetico Premier Plus Adoucisseur d’eau Installation et Guide d’utilisation
18
Informations de sécurité
Veuillez lire attentivement toutes ces informations avant
d'installer et d'utiliser l'adoucisseur d'eau.
Installateur qualifié
Kinetico recommande de confier
l'installation à un installateur qualifié.
Le non respect des instructions
d'installation peut entraîner l’annulation
de la garantie limitée.
Température de l'eau
N'installez pas l'adoucisseur Kinetico
dans une zone où la température de l'eau
peut dépasser 49°C ou peut entraîner
le gel de l'appareil. Les températures
négatives endommagent le système.
Pression de l'eau
N’eectuez pas cette installation si la
pression d’installation est supérieure à 6
bars (87 psi), à moins qu’un régulateur
adapté ait été installé en amont de
l’adoucisseur.
Trop plein
TRÈS IMPORTANT:
Le trop plein du coret de
l’adoucisseur doit être raccordé
à une évacuation des eaux usées
avec un tuyau souple 1/2’’. Cette
recommandation importante permet
d’éviter d’éventuels dégâts en cas de
dépassement de la capacité du coret.
Il faut veiller à ce que le tuyau souple
ne soit pas plus haut que le trop plein
du coret.
INSTALLATEUR
1
2
34
5
6
0bar

www.kinetico.eu
19
Tuyauterie cuivre/plastique
Lorsqu'une tuyauterie mixte cuivre/
plastique est utilisée, Kinetico conseille
de se fier aux obligations réglementaires
afin d'assurer une mise à la terre
adéquate.
Utilisation abusive
Ne convient pas au traitement d'une eau
non sûre sur le plan microbiologique, ou
d'une eau dont la qualité est inconnue,
sans désinfection adéquate en amont ou
en aval du système.
Conformité à la réglementation
Vous devez impérativement veiller à la
conformité de l'installation aux codes et
règlements applicables en matière de
plomberie.
Schéma de plomberie
Veuillez consulter le schéma de
plomberie page24 avant de
commencer l'installation.
1
2
34
5
6
0bar

Kinetico Premier Plus Adoucisseur d’eau Installation et Guide d’utilisation
20
Contenu de la boîte
Repérez les pièces suivantes avant de commencer.
Caractéristiques
Dimensions du boîtier @ base 645 x 480 x 396 mm
Sel consommé par régénération 0.56 kg
Durée de régénération 11 minutes
Débit pour une perte de charge à 1 bar 22.7 l/min
Raccords - entrée/sortie ¾” BSP
Pression de service min/max 1.8 - 6 bars
Température de service min/max 2 - 49˚C
Dureté
max
1 support de maintien
pour entrée/sortie et
goupille
4 joints toriques
1 tube de silicone 2cc 2 joints plats 3/4’’
Disque indicateur A B C D E F G H I * J * K * L * M *
PPM 207 221 238 256 279 305 337 376 426 456 490 531 578 635 686 770 878 1020
˚f 21 22 24 26 28 30 34 38 43 46 49 53 58 64 69 77 88 102
˚D 12 12 13 14 16 17 19 21 24 26 27 30 32 36 38 43 49 57
Litres entre les
régénérations 1583 1480 1377 1274 1171 1068 965 862 759 708 656 605 553 502 450 399 347 224
Dureté
max
2 x 3/4” BSP adaptateurs
d’entrée/sortie
Vanne by-pass
(incluse uniquement avec le Premier Plus HE ALT BP)