KING CANOPY Booth in a Bag User manual

Booth in a Bag™ 10ft x 10ft
9’10”Wide x 9’10” Deep,
6’8” Side Height /9’6” Center Height
King Canopy Item #: BIAB10-WH
With 4 Legs, Side Walls, Foot Pads & Roller Bag
WARNING:
Keep all ame and heat sources
away from this tent fabric. Meets
the ammability requirements of
CPAI-84 Section 6 and NFPA-701.
It is not re proof. The fabric will burn if
left in continuous contact with
any ame source.
Distributed by: PIC America, LTD.
8009 Purfoy Road • Fuquay-Varina, NC 27526
1-800-800-6296 • www.kingcanopy.com

PARTS LIST
A
C
D
B
PFOOT
BALLW
40” ROLLER BAG
COVER
SIDE WALLS
END WALLS
3WPC
A) 6X6-PC-BIAB 4 Pcs 78”x13 /8” Leg Pipes with Shock Cord
B) 9X7-PC-BIAB 3 Pcs 115”x13 /8” Roof Pipe with Shock Cord
C) 5X2-PC-BIAB 4 Pcs 62”x13 /8” Roof Pipe with Shock Cord
D) 8X3-PC-BIAB 2 Pcs 8’31 /2”x13 /8” Brace Pipe with Shock Cord
3WPC 6 Pcs 3 Way Connectors
PFOOT 4 Pcs Plastic Foot Pads
BALLW 10 Pcs White Elastic Ball Bungee Straps
TBIAB1010WH 1 Pc 10’x10’ Booth in a Bag Fitted Cover
TBIAB10SW-BS 2 Pcs 10’ Side Wall with Bug Screen Window
TBIAB10EW 1 Pc 10’ End Wall
TBIAB10EWZ 1 Pc 10’ End Wall with Zippered Door
CRB40 1 Pc 40” Canopy Roller Bag
BOLTWNUT Set 4 Bolts & Wing Nuts
BOLTS &
WINGNUTS

FRAME ASSEMBLY
D
BBB
CC
CC
A
A
A
A
D
3WPC 3WPC
3WPC
3WPC 3WPC
3WPC
PFOOT
PFOOT
PFOOT
PFOOT
Step 2) Start assembly of frame at the center ridge. Connect the center ridge
pipe to the 3 way connectors as shown
Step 1) Begin by laying out the parts as shown above.

FRAME ASSEMBLY
Step 3) Assemble one side of roof frame. Make sure the bolt
holes face outward as shown and that the 3-Way tting (3WPC)
is placed with the curved bend facing the front and rear .
Step 4) Assemble the other side of roof frame as
shown above following the same directions as in
step 3.
Step 5) Connect one side of the brace bar (Pipe D)
with the bolt and wing nut. Make sure round head of
bolt faces exterior of tent.
Step 6) Bolt the other side of brace bar to the frame.
Step 7) Make sure the round head of bolt faces the
exterior of tent.
Step 8) Set cover on one side of frame as shown.

COVER & WALL ASSEMBLY
Step 9) Pull cover over frame. Make sure the peak of
the cover lines up with the peak of the frame.
Step 10) Begin attaching ball bungees to the cover
by starting at opposite corners and then attaching
the other 2 corners.
Step 11) Loop the ball bungee straps through the
grommet from underside of cover. Attach one to
each side of the frame at the corner as shown above.
Attach
First
Attach
First
Attach
Second
Attach
Second
Step 12) Once the corners of the cover are attached,
the cover will will help hold frame together. Now the
legs can be inserted.
Step 13) Lift one side of the canopy and insert the
legs into the 3 way connectors.
Step 14) Go underneath the canopy and attach Ball
Bungee Straps to each end of the cover. Be sure to
attach a ball bungee through every open grommet.

COVER & WALL ASSEMBLY
Step 15) Insert the other 2 legs and attach the leg
skirt straps to the footpads on all 4 legs.
Step 16) Begin hanging the side walls by attaching
the velcro straps to the velcro straps on the cover
starting from the outside edge of the pipe.
Step 17) Attach the velcro
straps around the each leg.
Step 18) Velcro the end walls to the end of the cover
and zipper on to the side wall to completely close
the corner. Repeat with the other side and front wall.
Step 21) You can roll up the doors and and secure
with the straps.
Step 19) Join zipper at
the top of the walls.
Step 20) Zipper walls
together in downward
motion.

Step 21) The windows can be rolled up and secured
with the straps.
Step 22) Thee are three zippers on the front wall so
that you can roll up the two sides individually.
ANCHORING YOUR CANOPY
This canopy is designed for use as a temporary structure. After assembly, the canopy MUST BE securely
anchored to the ground to prevent damage from winds. Your canopy will act like a kite in the wind if not
properly and securely anchored to the ground. Severe winds will cause the frame to twist and unanchored
legs will fall, thereby collapsing the canopy. If severe winds are expected, you must remove the cover from
the frame to prevent damage.
Step 1
Measure out at least 36in from each leg. Screw each anchor into the ground leaving 2in between the ground
and the eye of each anchor. We strongly recommend that your unit be anchored 36in from each leg although
this may not be possible in all cases. DO install anchors as close to 36in away from legs as possible.
Step 2
Tie anchor cable or rope around the connector
at the top of each leg of the canopy.This is done
by stringing the rope through the corner grommet
located at each corner on the cover.
Step 3
Securely tie the other end of the cable or rope
through the eye of the anchor and pull tight.
Step 4
Now, continue to screw each anchor into the ground
until the eye of the anchor is ush with the ground.
This will secure the anchor rope even tighter.
Step 5
To secure the side walls insert a ground stake through the
open grommets at the bottom of both side walls.
NOTE: You should check and tighten the rope frequently to
ensure maximum stability of your canopy and to protect
against wind damage. ANCHOR KIT NOT INCLUDED
WITH THIS CANOPY

IMPORTANT NOTICE: PLEASE READ CAREFULLY
We are condent that you will be completely satised with your King Canopy unit. Please take a moment
to read the very important information below, and call us with any questions you may have.
King Canopy/PIC America, LTD. has no control over wind, snow, ice, rain or any other weather condition and
we are in no way responsible for any damage caused by the canopy or to the canopy. We suggest you contact
your insurance carrier just as you would for any other outside structure.
OTHER PRECAUTIONS WHICH MUST BE FOLLOWED:
Keep all ame and heat sources away from this tent fabric.The tent fabric will burn if left in continuous contact
with any ame source.
DO NOT cook underneath or near canopy.
DO NOT store or use ammable liquids underneath or near canopy.
DO NOT ignite or store reworks underneath or near canopy.
DO NOT use bleach to clean cover.
DO NOT dry clean cover.
DO NOT wash cover in washing machine or dry in dryer. Hand wash with mild soap and water only.
DO NOT allow rain water, snow or ice to accumulate on top of cover.
DO NOT hang or suspend anything from the frame, grommets, truss system or ball straps of the unit.
REMOVE canopy cover before a storm, or disassemble entire canopy unit if possible.
REMOVE rain water, snow and ice from canopy cover.
This is a temporary structure and is not recommended for use as a permanent structure.

PRODUCT INFORMATION
Defective Parts
We try our best to eliminate any defective parts that are shipped with our products. If, however, you should nd
a defective part, we will replace – free of charge – any part which is defective. You will need to provide proof
of purchase showing date of purchase and provide us with detailed description of the defective component.
Your replacement will be shipped by ground shipping, freight prepaid. Next day or express shipping will
require freight collect and paid for by you, the consumer. Damages from improper anchoring, strong winds,
snow, ice or rain are not considered defects.
Improper Anchoring, Strong Winds, Rain Snow, or Ice
King Canopy/PIC America, LTD. does not guarantee these canopies under strong weather conditions. These
canopiesaredesignedtoprotectagainstdamagescaused by sun, rain, treesap, birds,etc. Theyarenotdesigned
to hold roof loads that accompany snow, ice or heavy rains. If your canopy is not anchored securely, it can be
lifted by the wind and will y away. If your canopy takes ight, we are not responsible for any replacement. If
you know strong weather is predicted, remove the cover or take down the canopy unit completely. The cover
is designed to be quickly and easily removed.
Warranty
All components of this canopy feature a 1-year limited warranty and are warranted to be free from defects in
material and workmanship for a period of 1-year. You must complete and return the enclosed warranty card
promptly after purchase. Please retain your proof of purchase receipt; you will be asked to provide this receipt
in order to obtain warranty service.
Non-Warranty Replacement Parts
If after expiration of the warranty period, you require replacement parts please contact us at 1-800-800-6296.
We stock replacement parts and make them available to you at discounted prices. Our customer service
department will be pleased to assist you in any way possible.
Certain regions of the country are extremely hard on covers of any kind. Normal wear and tear is not covered
under the warranty, and should be expected.
In order to receive a discounted or free replacement part, you may be asked to return the part, freight prepaid,
to our warehouse for inspection before we will send a replacement. You must, in all cases, provide a copy of
your receipt showing the date of purchase, model number and price.
For missing parts, replacement parts or any questions:
Please Call 8:00am – 5:00pm EST, Monday – Friday
1-800-800-6296 or 1-919-552-2977
Or you can fax us at: 1-919-552-5069
Replacement parts and customer service is also available through our website.
Please visit us at www.kingcanopy.com