Kingsman Fireplaces ZCV3622N User manual

Model Numbers:
ZCV3622N, ZCV3622NE, ZCV3622NE2, ZCV3622LP, ZCV3622LPE, ZCV3622LPE2,
ZCVRB3622N, ZCVRB3622NE, ZCVRB3622NE2, ZCVRB3622LP, ZCVRB3622LPE,
ZCVRB3622LPE2
Certified to:
ANSI Z21.88-2017 • CSA 2.33-2017 Vented Gas Fireplace Heaters, CSA 2.17-2017
Installation Instructions
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
A Division of R-Co. Inc.
2340 Logan Ave.
Winnipeg, Manitoba Canada
R2R 2V3 Ph.: [phone]
Printed in Canada February 4, 2021
Part# 36ZCV-MAN17
This appliance may be installed in an aftermarket,
permanently located, manufactured home (USA
only) or mobile home, where not prohibited by local
codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is
not convertible for use with other gases, unless a
certified kit is used.
ZCV3622 SOLARA
ZCVRB3622 SKYLINE
VENTED GAS FIREPLACE HEATER:
NOT FOR USE WITH SOLID FUEL

Table of Contents
Cover......................................................................................................................................................................
1
Table of Contents....................................................................................................................................................
2-3
Pre-installation Questions and Answers / Operations and Maintenance Instructions.............................................
4
Safety Screen Installation.......................................................................................................................................
5
Warnings, Installations and Operations - Installation Regulations..........................................................................
6
Installation Requirements for the Commonwealth of Massachusetts / Carbon Monoxide (CO) Detector..............
7
Mobile Home/Manufactured Housing Installation...................................................................................................
8
Installation & Framing
Recommendations for Finishing of Clean View Linear Products............................................................................
9
Fireplace Installations in Covered Outdoor Locations............................................................................................
10
Framing for your Gas Fireplace..............................................................................................................................
11
ZCV3622 / ZCVRB3622 Nailing Tab Guide............................................................................................................
12
Locating your Appliance / Unit Dimensions............................................................................................................
13
ZCV3622 / ZCVRB3622 Framing Dimensions and Clearances -With Factory Installed Flue Restrictor................
14
ZCV3622 / ZCVRB3622 Framing Dimensions and Clearances -With Factory Installed Flue Restrictor Removed..........
15
ZCV3622 / ZCVRB3622 Facing Requirements......................................................................................................
16
ZCV3622 / ZCV3622RB Mantel & Mantel Leg Clearances....................................................................................
17
Accessories and Options
ZCV36S1BL- ZCV3622 Surround Installation........................................................................................................
18
ZCV36SWFBL – Flat Surround for ZCV3622.........................................................................................................
19
ZCVRB36SWFBL – Flat Surround for ZCVRB3622...............................................................................................
20
ZCVRB36S- Surround Installation..........................................................................................................................
21
ZCV36LMK Magnet Kit- ZCV3622 / ZCVRB3622...................................................................................................
22
Fan Kit Installation..................................................................................................................................................
23
Fan Speed Control Outside of Fireplace.................................................................................................................
24
ZCV3622 / ZCVRB3622 ML / PRL Liner Installation Guide....................................................................................
25
Door and Glass Information....................................................................................................................................
26
LOGC51 5 Piece Oak Log Set for ZCV3622..........................................................................................................
27-28
MQLOGC22 for MQZDV3318 / 3622 / ZCV3622....................................................................................................
29-30
MQLOGC23 4 Piece Driftwood Log Set for ZCV3622............................................................................................
31
MQRSP5 for MQZDV3318 / 3622 / ZCV3622........................................................................................................
32-33
ULK2 Universal Light Kit (Optional Accent Lighting Kit).........................................................................................
34-35
MQ Accessories for ZCVRB3622...........................................................................................................................
36-37
Burner System
Gas Line Installation...............................................................................................................................................
38
Millivolt System, Lighting, and Burner Control........................................................................................................
39
Annual Inspection List for Determining Safe Operation of a Direct Vent Gas Fireplace.........................................
40
Burner System Maintenance...................................................................................................................................
41
Conversion Kit Instructions – PART A....................................................................................................................
42-43
Gas Conversion for Top Convertible Pilot – Part B (series 0190XYZ)....................................................................
44
Gas Conversion for Modulator – PART C...............................................................................................................
45
ZCVRB3622 Burner System Removal....................................................................................................................
46
P2 Box - ZCV3622 / ZCV3622RB...........................................................................................................................
47
IPI Proflame 1
IPI Proflame 1 Overview / Components..................................................................................................................
48
IPI Proflame 1 Remote Control Operation..............................................................................................................
49
IPI Proflame 1 Parts List.........................................................................................................................................
50
Configuration #1: Basic Manual HI/LO and Manual ON/OFF Capabilities..............................................................
51
Configuration #2: Remote ON/OFF and Manual HI/LO Capabilities.......................................................................
52
Operating the Receiver Without Batteries- Millivolt and Proflame 1.................................................................................
53
Configuration #3: Remote ON/OFF, variable HI/LO, and Fan Capabilities.............................................................
54
IPI Electronic Ignition Lighting Instructions.............................................................................................................
55
2

IPI Proflame 2
IPI Proflame 2 Parts List / Basic System / Configuration GTMFL...........................................................................
56
IPI Proflame 2 Module and Remote Control...........................................................................................................
57
Cold Climates – CPI Setting – IPI Proflame 2 Remote Control..............................................................................
58
IPI Proflame 2 Remote Control...............................................................................................................................
59-60
IPI Proflame 2 Label Diagram...........................................................................................................................................
61
Venting
Vent Terminal Clearances......................................................................................................................................
62
General Vent Installation .......................................................................................................................................
63
Installation of Side Wall Venting…………………………………………………………………………………………..
64
Venting Routes and Components / Horizontal Venting Table from Bottom of Fireplace......................................
65
Venting Straight Up Through Roof………………………………………………………………………………………...
66-67
Vertical Venting over 15 Feet..................................................................................................................................
68
Z47ST24 / Z47ST36 Horizontal Snorkel Terminations...........................................................................................
69
Fireplace Installations Using Co Linear Flex Kits....................................................................................................
70
Glass Safety / Termination Cap Safety...................................................................................................................
71
Approved for Power Vent PVH58………………………………………………………………………………………….
72
Parts Lists
PVH58 Parts List…………………………………………………………………………………………………………….
73-74
ZCV3622 Parts List.................................................................................................................................................
75
ZCVRB3622 Parts List............................................................................................................................................
76
ZCV3622 / ZCVRB3622 Common Parts and Venting............................................................................................
77
Troubleshooting
Troubleshooting the Gas Control System...............................................................................................................
78
Warranty
Limited Lifetime Warranty………………………………………………………………………………………………......
79
3

Pre-installation Questions and Answers
About curing of the paint
Your stove or fireplace has been painted with the highest quality silicone stove paint. This paint dries quickly in 15-20
minutes when first applied at the factory. However, due to the high temperature silicone components, the paint will cure
when heat is applied to the appliance as it is first used. The following information applies to the curing process to get the
paint fully hard and durable.
Fire the appliance four successive times for 10 minutes each firing and a 5 minute cool down between each. Be aware
during log and firebox paint curing that a white deposit may be developing on the inside of the glass doors. It is important
to remove this white deposit from the glass doors using a fireplace glass cleaner.
 Babies, small children, pregnant women and pets should leave the area during the cure phase.
 Ventilate well, open doors and windows.
 Do not touch during curing.
Why does my fireplace or stove give off odor?
It is normal for your fireplace to give off some odor at first. This is due to the curing of the paint, adhesives, silicones and
any undetected oil from the manufacturing process as well as the finishing materials used with the installations (e.g.
marble, tile and the adhesives used to adhere this product to the walls can react with heat and cause odors).
It is recommended that you burn your gas fireplace or stove for a minimum of four hours at a time with the fan off (if a fan
is present) after the curing of the paint has been completed. These odors can last upward to 40 hours of burn time; keep
burning at a minimum of four hours per use until odors dissipate.
Noise coming from the fireplace?
Noise is caused by the expansion and contraction of metal as the appliance heats up and cools down. This is normal and
is similar to the sounds produced by a furnace or heating duct. This noise does not affect the operation or longevity of
your fireplace.
It is also normal for the fan to make some noise when it comes on. This noise can be reduced somewhat by turning down
the speed of the fan with the variable speed control. Be aware, however, that this will reduce the volume of heated air
circulated into the room by the fan.
Note to the Installer:
Be sure appliance is working properly and its operation (including remote control operation, if included) is fully explained
to and understood by the customer.
Operations and Maintenance Instructions
For safe installation and operation note the following:
 Be sure to read and understand all the instructions in this manual before operation of appliance.
 Ensure all wiring is correct and properly enclosed to prevent possible shock.
 Check for gas leaks.
 Make sure the glass door is properly installed before operation. Never operate the appliance with the glass door
removed.
 Make sure venting and termination cap are installed and unobstructed.
 If brick or porcelain liners are used, ensure they are installed.
 Verify that the pilot can be seen when lighting the appliance. If not, the log or rock placement is incorrect.
 If the unit is turned off, you must wait a minimum of 60 seconds before re-lighting it.
 Venting systems should be periodically examined by a qualified agency.
 The flow of combustion and ventilation air must not be obstructed.
 The Burner/Log Assembly has been engineered and permanently adjusted for proper flame control.
 Periodically remove the logs from the grate assembly and vacuum any loose particles from the grate and burner
areas. See Log Placement page to remove logs. Vacuum burner parts and replace logs.
 Never use your gas fireplace as a cooking device.
 Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous
operation. Verify proper operation after servicing.
 Areas in and around the Chase Vent Openings should be cleaned annually.
4

ZCV3622 / ZCV362RB Safety Screen Installation / Removal
Hook Lower Clip onto glass door frame.
Press down and push upper clip under top glass door frame.
Included with fireplace:
[1] Safety Screen
⚠WARNING:
Wait until unit is COMPLETELY
cool before touching glass or
attempting to install or remove
Child Safety Screens.
To install screens
hook bottom clip
onto glass door
frame, then press
down and push
upper clip under
top glass door
frame, then
release. Clip will
hook onto frame.
To remove
Safety
Screens
WAIT UNTIL
FIREPLACE IS
COMPLETELY
COOL.
Press down on
upper clips and
remove screen
from fireplace
glass door.
TOP VIEW
Upper Clip
Lower Clip
Upper Clip
NOTE: Screen is symmetrical from top to bottom.
CLIPS
SIDE VIEW
5

Warnings, Installations and Operations - Installation Regulations
This gas appliance must be installed by a qualified installer in accordance with local building codes, or in the absence of local codes, with the
current CAN/CSA-B149.1 or .2 Installation Code (in Canada) or the current National Fuel Gas Code Z223.1- NFPA 54 when installed in the
United States.
This appliance, when installed, must be electrically connected and grounded in accordance with local codes, or in the absence of local codes,
with the current CSA C22.1 Canadian Electrical Code or with the National Electrical Code; ANSI/NFPA 70 when installed in the United States.
WARNING
FOR SAFE INSTALLATION AND OPERATION OF YOUR GAS FIREPLACE PLEASE NOTE THE FOLLOWING:
1. Do not clean when the glass is hot.
2. Do not use abrasive cleaners.
3. Using a substitute glass will void all product
warranties.
4. For safe operation, glass doors must be closed.
5. When purging the gas line, the glass front must be
removed.
6. Do not strike or abuse glass. Take care to avoid
breakage.
7. Do not alter gas orifice.
8. No substitute materials may be used other than
factory supplied components.
9. This appliance gives off high temperatures and should
be located out of heavy traffic areas and away from
furniture and draperies.
10. Children and adults should be alerted to the hazards
of the high surface temperatures of this appliance and
should stay away to avoid burns or ignition of clothing.
11. Young children should be carefully supervised when
they are in the same room as the appliance. Toddlers,
young children and others may be susceptible to
accidental contact burns. A physical barrier is
recommended if there are at risk individuals in the
house. To restrict access to a fireplace or stove, install
an adjustable safety gate to keep toddlers, young
children and other at risk individuals out of the room
and away from hot surfaces.
12. Under no circumstances should any solid fuels (wood,
paper) be used in this appliance.
13. Under no circumstances should this appliance be
modified. Any parts that have to be removed for
servicing should be replaced prior to operating this
appliance.
14. Any safety screen, guard, or barrier removed for
servicing an appliance must be replaced prior to
operating the appliance.
15. Installation and repair should be done by a qualified
service person. The appliance should be inspected
before use and at least annually by a professional
service person. More frequent cleaning may be
required due to excessive lint from carpeting, bedding
material, et cetera. It is imperative that control
compartments, burners and circulating air
passageways of the appliance be kept clean. Make
sure that the gas valve and pilot light are turned off
before you attempt to clean this unit.
16. Clothing or other flammable material should not be
placed on or near the appliance. This appliance
should not be used as a drying rack for clothing nor
should Christmas stockings or decorations be hung
from it.
17. Do not use this heater if any part has been under
water. Immediately call a qualified service technician
to inspect the heater and to replace any part of the
control system and any gas control which has been
under water.
18. Do not operate appliance unless completely installed
as per installation instructions.
19. Failure to position the parts in accordance with these
diagrams or failure to use only parts specifically
approved with this appliance may result in property
damage or personal injury.
20. WARNING: Do not operate appliance with the
glass front removed, cracked or broken.
Replacement of the glass should be done by a
licensed or qualified service person.
21. The appliance area must be kept clear and free from
combustible materials, gasoline, and other flammable
vapors and liquids.
22. The front of the fireplace gives off high temperatures
that could ignite combustible material which is kept
close to the front of the unit.
23. Ensure that power to the Fireplace is turned off before
servicing.
24. Do not operate this Fireplace without the glass front or
with a broken glass.
25. Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage.
Refer to the owner’s information manual provided with
this appliance. For assistance or additional information
consult a qualified installer, service agency, or the gas
supplier.
26. Operation of this appliance when not connected to a
properly installed and maintained venting system or
tampering with the blocked vent shutoff system can
result in carbon monoxide (CO) poisoning and
possible death.
27. This appliance is equipped with a three-prong
(grounding) plug for your protection against shock
hazard and should be plugged directly into a properly
grounded three-prong receptacle. Do not cut or
remove the grounding prong from this plug.
28. NOT INTENDED FOR USE AS A PRIMARY HEAT
SOURCE. This appliance is tested and approved as
either supplemental room heat or as a decorative
appliance. It should not be factored as primary heat in
residential heating calculations.
29. This appliance must not be connected to a chimney
flue serving a separate solid-fuel burning appliance.
6

Installation Requirements for the Commonwealth of Massachusetts
In the Commonwealth of Massachusetts, the installer or service agent shall be a plumber or gas fitter licensed by the
Commonwealth.
When installed in the Commonwealth of Massachusetts or where applicable codes; the unit shall be installed with a CO
detector per the requirements listed below.
1. For direct-vent appliances, mechanical-vent heating appliances or domestic hot water equipment, where the bottom of
the vent terminal and the air intake is installed below four feet above grade the following requirements must be
satisfied:
A. If there is not one already present, on each floor level where there are bedroom(s), a carbon monoxide
detector and alarm shall be placed in the living area outside the bedroom(s). The carbon monoxide detector
shall comply with NFPA 720.
B. A carbon monoxide detector shall be located in the room that houses the appliance or equipment and shall:
 Be powered by the same electrical circuit as the appliance or equipment such that only one service switch
services both the appliance and the carbon monoxide detector;
 Have battery back-up power;
 Meet ANSI./UL 2034 Standards and comply with NFPA 720; and
 Have been approved and listed by a Nationally Recognized Testing Laboratory as recognized under 527
CMR.
C. A Product-approved vent terminal must be used, and if applicable, a Product-approved air intake must be
used. Installation shall be in strict compliance with the manufacturer’s instructions. A copy of the installation
instructions shall remain with the appliance or equipment at the completion of the installation.
D. A metal or plastic identification plate shall be mounted at the exterior of the building, four feet directly above
the location of vent terminal. The plate shall be of sufficient size to be easily read from a distance of eight feet
away, and read “Gas Vent Directly Below”.
2. For direct-vent appliances, mechanical-vent heating appliances or domestic hot water equipment where the bottom of
the vent terminal and the air intake is installed above four feet above grade the following requirements must be
satisfied:
A. If there is not one already present, on each floor level where there are bedroom(s), a carbon monoxide
detector and alarm shall be placed in the living area outside the bedroom(s). The carbon monoxide detector
shall comply with NFPA 720.
B. A carbon monoxide detector shall:
 Be located in the room that houses the appliance or equipment;
 Be either hard-wired or battery powered or both; and
 Shall comply with NFPA 720.
A Product-approved vent terminal must be used, and if applicable, a Product-approved air intake must be used.
Installation shall be in strict compliance with the manufacturer instructions. A copy of the installation instructions shall
remain with the appliance or equipment at the completion of the installation.
For the state of Massachusetts a T-handle gas shut-off valve must be used on a gas appliance. This T-handle gas shut-
off valve must be listed and approved by the state of Massachusetts. This is in reference to the state of Massachusetts
state code CMR238.
Carbon Monoxide (CO) Detector
NOTE: It is recommended that a Carbon Monoxide (CO) Detector be installed in or near bedrooms and on all levels of
your home. Place a detector about 15ft [4.5m] outside the room that houses your gas appliance.
Certified for installation in a bedroom or bed/sitting room. In Canada must be installed with listed millivolt thermostat.
In USA see local codes.
7

Mobile Home/Manufactured Housing Installation
This Direct Vent System Appliance must be installed in accordance with the manufacturer’s installation instructions and the
Manufactured Home Construction and Safety Standard Title 24 CFR, Part 3280, or the current Standard for Fire Safety Criteria for
Manufactured Home Installations, Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240 MH Mobile Home Standard in
Canada.
THE VENTED GAS FIREPLACE HEATERS (ANSI Z21.88) IN THIS MANUAL MAY BE INSTALLED IN MANUFACTURED (MOBILE)
HOMES AFTER FIRST SALE IN THE USA.
THE VENTED GAS FIREPLACE HEATERS (ANSI Z21.88) IN THIS MANUAL MAY BE INSTALLED IN MANUFACTURED (MOBILE)
HOMES IN CANADA.
Please follow the current ANSI/NFPA 70 National Electrical Code in the USA and CAN/CSA C22.1 Canadian National
Electrical Code in Canada.
An appliance must be grounded to the steel chassis of the home with 8 ga. copper wire using a serrated or star washer to
penetrate paint or protective coating to insure grounding.
Use carriage bolt at the attachment point (see diagram above) to secure the appliance to the floor.
For required venting components see venting installation in appropriate section of this manual.
Certified for installation in a bedroom or bed/sitting room. In Canada must be installed with listed millivolt thermostat. In USA see local
codes.
Warning: Do not compromise the structural integrity of the manufactured home wall, floor
or ceiling, during installation of appliance or venting.
Appliance Must Be Secured To
Structure Using Supplied Nailing
Tabs And Or Fastened To Floor.
Use Existing Hole Or Remove
Existing Screw To Mount Ground
Wire (Nailing Tab Screw).
Serrated Or Star Washer
Ground Wire From Appliance To Steel
Chassis Of Mobile Home. USE 8GA
COPPER WIRE.
8

Recommendations for Finishing of Clean View Linear Products
When finishing the wall around the fireplace, it is critical that the wall covering be fastened properly. It is acceptable to
pre-drill holes and use self-tapping screws which may be used to fasten a backer for tile, marble, etc. Screws being
installed through non-combustible board should be self-tapping type with a maximum length of 2 inches. Wall covering
fasteners, such as screws or nails, are not permitted in some locations. Do not drill or install longer screws which may
penetrate into the lower cover panel area as this may damage internal components.
 Only non-combustible materials may be used over the face of the appliance.
 We recommend that CONCRETE BOARD (non-combustible material) be tied in to the entire perimeter of the fireplace for
durability.
Finishing Recommendations (Obtained from professional construction contractors and finishers):
 Frame unit with metal studs (minimum 20 gauge).Wooden studs may be used, but may cause drywall screws to pop
or pull due to wood studs drying out.
 Minimum of 1/2” CONCRETE BOARD cement board (this non-combustible panel is ULC listed as a wall shield/floor
protector) and fasten to the entire perimeter framing.
 Use fiberglass (mesh) tape for all joints in area of the fireplace.
 Use Yellow joint mud (contains high amounts of glue) – two coats, finishing with one coat of green topping mud, sand
and prep for painting.
 If not using a surround, a metal “L” Trim may be used to finish perimeter of CONCRETE BOARD.
 Refer to the following website for more information on using CONCRETE BOARD Cement Board: www.cgcinc.com
OTHER NOTES:
-A full single sheet of non-combustible board (no joints) above the unit is recommended if possible.
-It is preferred to attach the non-combustible board to framing only and not directly to the unit to allow for expansion and
contraction during normal operation.
-Lighter colored painted surfaces may discolor due to heat exposure.
9

Fireplace Installations in Covered Outdoor Locations
– FOR BASIC MILLIVOLT UNITS ONLY- NO FAN – NO LIGHTS-
Kingsman and Marquis Direct Vent fireplaces may be installed into outdoor locations provided they are suitably protected
from direct water impingement. However, all installation clearances in the appliance manual must be observed. Framing,
Clearances to Combustibles, Mantel Heights, Facing Requirements, Venting Installation, etc. Use supplied Safety Screen.
 All wiring connections to line power shall be in accordance with outdoor requirements of; -NECA NFPA 70 in the USA
-Canadian Electrical Code, CSA C22.1 for Canada.
 The Fireplace is not to be operated in temperatures below freezing (0°C / 32°F).
 ⚠ NOTE: TEMPERED GLASS WARNING: Tempered glass is vulnerable to rapid and/or extreme changes in
temperature (thermal shock). Take care to prevent water from contacting the fireplace, especially if it is hot.
 See-Through Units are suitable for an outdoor location, but not on the outside wall of a house or other structure, as
air flows through both sides of the fireplace.
 A Minimum sheltering cover (overhang) of 1/2 the distance from the base of the fireplace to the ceiling (base of
roofline) is required.
EXAMPLE: The bottom of the fireplace is 84” from the ceiling.
Therefore, 42” of sheltering cover is required above fireplace.
CAUTION – Installation of an indoor gas fireplace with an outdoor exposure is not covered under the (ANSI
Z21.88 – CSA 2.22 or ANSI Z21.50 – CSA 2.33) standard(s) used to certify the indoor gas-fired fireplace. The
Intertek safety certification will not apply to this installation method. This installation method must be deemed
acceptable by the Authority Having Jurisdiction (AHJ) prior to the indoor gas fireplace being installed.
OUTDOOR
AREA
Glass
Door
Glass
Door
Glass
Door
Outside Wall
of House
10

ZCV3622 / ZCVRB3622 Framing Your Gas Fireplace
This section is intended for qualified installers only. Before beginning, make note of where the gas and electrical accesses are
located on the unit. This will streamline the construction process. Furthermore, familiarize yourself with the venting and
clearance requirements (see Venting section) for this appliance. Failure to comply with those requirements can seriously
compromise the safety and operation of the fireplace.
Specifications
1.Cold climate installation recommendation: When installing this fireplace against non insulated exterior wall or chase,
it is recommended that the outer walls be insulated to conform to applicable insulation codes. Drywall & vapor barrier
must be installed over insulation to prevent contact of insulation and unit.
2.Choose fireplace location and frame in accordance with the fireplace framing dimensions specified (view diagrams).
3.Drywall or other combustible material can extend up to the Drywall Stops located on the sides of the unit, and up to
the bottom and top.
4.A Hearth is not required for this unit.
Certified for installation in a bedroom or bedsitting room. In Canada must be installed
with listed millivolt thermostat (Not permitted for decorative vented gas fireplaces installed
in the U.S.A.). In USA see local codes.
Stand-off Locations
Make note of where the stand-off locations are. These stand-offs are provided as indicators to illustrate the
boundaries for framing. Therefore, no framing material is permitted to extend beyond these stand-offs.
Vertical Venting in Cold Climates
In cold climate conditions where temperatures go below -10 degrees Celsius or 14 degrees Fahrenheit, we recommend
that the chase be insulated and where the vent pipe enters into the attic space that the pipe be wrapped with an
insulated Mylar sleeve. This will increase the temperature of the vent and help the appliance to vent properly in cold
weather conditions.
It is also important in vertical vented direct vent appliances that the appliance be operated daily during the winter months
as this will help stop the termination from freezing up. We recommend using a thermostat (Not permitted for decorative
vented gas fireplaces installed in the U.S.A.) set at room temperature to allow the unit to cycle.
For IPI models it may be necessary to set the appliance to Standing Pilot mode to maintain heat in the cavity. The
purpose of this procedure is to prevent cold air from penetrating the chimney and then onto the living space. Therefore,
when the internal temperature is slightly elevated the fireplace is able to freely exhaust its combustion and hence making
it easier to startup.
Nailing Tabs
Caution: Standoffs on top
and back of the unit must be
folded into position &
screwed down PRIOR to
installation.
Holes are provided in bottom of
unit to secure appliance to floor
after installation.
Nailing Tabs
11

ZCV3622 / ZCVRB3622 Nailing Tab Guide
These Nailing Tabs can be used in two ways:
1/2” Drywall Flush with Face of Fireplace –Fireplace and
Combustible Wall to be covered with a surround and / or Non-
Combustible Materials (e.g. Stone around Fireplace).
Framing Flush with Face of Fireplace -Fireplace to be
covered with Non-Combustibles (e.g. Concrete Board) for
Flat Wall appearance. NOTE: 1/2” MUST BE ADDED TO
FRAMING DEPTH OF UNIT. USE THIS METHOD FOR
ZCVRB3622 SURROUNDS.
2 Nailing Tabs are
located on each
side of the fireplace
front frame.
Nailing Tab
Framing Stud
Drywall
Surround
Concrete Board
Drywall
Framing Stud
Nailing Tab
Nailing Tab
Framing Mount
Nailing Tabs Must
Be Rotated 180°
And Folded Back
Onto Framing Stud.
Framing Stud
Nailing Tab
Nailing Tab
Framing Stud
ZCV3622
ZCVRB3622
Tile Lip
TOP VIEW
TOP VIEW
Surround
12

ZCV3622 / ZCVRB3622 - Locating your Appliance
Installing with Top
V ent
A - Flaton a wall D - As a
room divider
B - Across thecorner E - Flat on wallcorner
C - As an island F - Exterior wall
Island installation with a top vent is possible as long asthe
horizontal portion of the vent system does not exceed 20
feet (6.1 m).
ZCV 3622 / ZCVRB3622 Fireplace Dimensions
TOP
FRONT
LEFT
SIDE
13

ZCV3622 / ZCVRB3622 Framing Dimensions and Clearances
-With Factory Installed Flue Restrictor-
NOTE: Units above the following Serial Numbers will have the Flue Restrictor: ZCV3622 #2016 / ZCVRB3622- #10674
Determine whether face of fireplace will be:
 Flush with finished wall (e.g., for surround, cultured stone or other non combustible covering).
 Flush with framing (to be covered with concrete board for a Flat Wall appearance).
Refer to Nailing Tab Guide section also.
Clearance to Combustibles ZCV3622 / ZCVRB3622
Front
36” [92cm]
Back (from Stand-offs)
0” [0cm]
Side (from Stand-offs)
0” [0cm]
Floor*
0” [0cm]
Minimum Ceiling Height (from bottom of
fireplace)
60”
Top (from Stand-offs)
0” [0cm]
Top of 90° Bend in minimum Enclosure
of 60”
2-1/2” [6.35cm]
VENTING SYSTEMS
Top of Horizontal Pipe
1/1/2” [3.8cm]
Side & Bottom of Horizontal Pipe
1” [2.5cm] All Vent
Systems
Vertical Vent Pipe
1” [2.5cm] All Vent
Systems
Framing for Horizontal
Vent Termination
(See Installation of
Side Wall Venting
Section)
These structures are not load bearing.
NOTE: See Nailing Tab Guide section also.
54” MIN for NG
54” MIN for LP
Plus Rise of 1/4”
Per Foot*
RIGHT SIDE
This area can be recessed
up to 3” from Face of Unit
for a TV Recess.
*Note: If appliance is installed directly on carpeting or other
combustible material other than wood flooring, a metal or
wood panel extending the full width and depth of the
appliance must be used. Carpet may extend 1 inch above the
floor of the appliance.
Support
Straps
CORNER
FRAMING
14

LOW ENCLOSURE
ZCV3622 / ZCVRB3622 Framing Dimensions and Clearances
-With Factory Installed Flue Restrictor Removed-
RESTRICTOR MUST BE REMOVED BEFORE INSTALLATION
NOTE: Units above the following Serial Numbers will have the Flue Restrictor: ZCV3622 #2016 / ZCVRB3622- #10674
Determine whether face of fireplace will be:
 Flush with finished wall (e.g., for surround, cultured stone or other non-combustible covering).
 Flush with framing (to be covered with concrete board for a Flat Wall appearance).
Refer to Nailing Tab Guide section also.
Clearance to Combustibles ZCV3622 / ZCVRB3622
Front
36” [92cm]
Back (from Stand-offs)
0” [0cm]
Side (from Stand-offs)
0” [0cm]
Floor*
0” [0cm]
Minimum Ceiling Height (from
bottom of fireplace)
46-1/2”
Top (from Stand-offs)
0” [0cm]
Top of 90° Bend in minimum
Enclosure of 46-1/2”
10” [25.4cm]
Top of 90° Bend in minimum
Enclosure over 46-1/2”
10” [25.4cm]
*See Chart on right
VENTING SYSTEMS
Top of Horizontal Pipe
1/1/2” [3.8cm]
Side & Bottom of Horizontal Pipe
1” [2.5cm] All Vent
Systems
Vertical Vent Pipe
1” [2.5cm] All Vent
Systems
Seal rivet hole after removing
rivet.
RESTRICTOR REMOVAL
(Restrictor must be removed)
These structures are not load bearing.
NOTE: See Nailing Tab Guide section also.
33” MIN for NG
45” MIN for LP
Plus Rise of 1/4”
Per Foot*
RIGHT SIDE
*For Propane Horizontal installations the venting must be an additional one foot above the minimum vertical rise off
the flue before going horizontal.
*Note: If appliance is installed directly on carpeting or other
combustible material other than wood flooring, a metal or
wood panel extending the full width and depth of the
appliance must be used. Carpet may extend 1 inch above
the floor of the appliance.
*Clearance to Top of 90° bend can
be reduced by 1” for every 2”
increase in height to a minimum of 2”
Enclosure Height
Top of 90° Bend
46-1/2”
10”
48-1/2”
9”
50-1/2”
8”
52-1/2”
7”
54-1/2”
6”
56-1/2”
5”
58-1/2”
4”
60-1/2”
3”
62-1/2”
(and Above)
2”
Restrictor is inside 4” flue.
Use a 1/8” Drill to remove rivet.
For Low Enclosure Framing.
Lowest enclosure possible
For Propane is 58”
Min Term Height = 45”
Top of Pipe = 49”
9” Clearance = 58”
Minimum Enclosure Height
for Propane is 58”
15

ZCV3622 / ZCVRB3622 Facing Requirements
Required Non-Combustible Areas- If you are covering the face of the fireplace:
Combustibles (i.e. Drywall) may be installed up to edge of fireplace only.
NOTE: MATERIALS COVERING THE FACE OF THE FIREPLACE MUST BE NON-COMBUSTIBLE
It is also recommended (but optional) to attach Non-combustible facing to framing. Dimensions for doing this are shown below.
Note: Do not drive excessively long screws into the face of the unit as internal parts may be damaged.
ZCV3622
ZCVRB3622
16

ZCV3622 / ZCV3622RB Mantel Clearances
Mantel Leg Clearances
Before installing any mantels it is
important to determine the combustibility
of its material(s). There are two types of
mantels to consider: Combustible and
Non-Combustible.
A Combustible Mantel is one that
consists of material(s) that may discolor,
combust, or lose its integrity in the
presence of heat. These types of mantels
must strictly conform to the dimensional
requirements shown.
Conversely, a Non-Combustible Mantel
is one that is constructed with material(s)
that will not combust. Check your local
codes and regulations to determine
whether your mantel is combustible or
Non-Combustible.
The advantage to Non-Combustible
Mantels is that it may extend right up to
the tile lip of the fireplace. Combustible
mantels must adhere to the dimensional
restrictions shown.
-Combustible Objects on Non-
Combustible Mantel Warning-
Combustible objects must not be placed
on a Non-combustible Mantel unless the
mantel meets the dimensional
requirements for a Combustible Mantel.
Determine whether your mantel
conforms to the requirements of a
Combustible Mantel.
Adjacent Wall
Adjacent Wall
Top View
Mantel
Dimensions are
from front face or
Non-Combustible
Facing Materials
covering fireplace.
17

ZCV36S1BL ZCV3622 Surround Installation
This surround will cover the gap between the fireplace face
and the drywall edges.
Face of Fireplace must be flush with drywall. Install
Fireplace with framing 1/2” behind face of Fireplace (See
Nailing Tab Guide Section).
Step 3 (illustrated): Install screws in top corners.
Step 4: Open Lower Panel and install screws through surround.
Raise Lower Panel and replace screws.
Step 2:
Slide surround over fireplace frame.
Step 1:
Remove [2] top screws in
Lower Panel and open.
Step 3:
Install DT screws through
surround into top corners.
Install screws into bottom
corners through surround.
ZCV36S1BL Surround
Parts List:
- [Qty-1] Surround Frame
- [Qty-4] #6 Self Tapping Screws
ZCV36S1BL Surround
ZCV36S1BL Surround
18

ZCV36SWFBL – Flat Surround for ZCV3622
This surround will cover the framing opening
between the fireplace face and the drywall edges.
 Face of Fireplace must be flush with
drywall. Install Fireplace with framing
1/2” behind face of Fireplace (See Nailing
Tab Guide Section).
 Bottom of Fireplace must be raised
1/2” above floor or hearth to install
this surround.
1. Hook Bottom Ledge of Surround onto Lower Panel of Fireplace. 2. Attach Surround with [2] Screws provided.
Each kit contains:
- [Qty-1] Surround Frame
- [Qty-2] #6 Self Tapping Screws
Bottom Ledge of
Surround
Lower Panel of
Fireplace
Attach to Upper Side Frame
with supplied Screws
Screw Holes
Lower Panel of Fireplace
37-1/2”
To Floor
Bottom of Fireplace must be raised 1/2” above floor
or hearth to provide clearance for Surround
19

ZCVRB36SWFBL – Flat Surround for ZCVRB3622
This surround will cover the framing opening
between the fireplace face and the drywall edges.
 Face of Fireplace must be flush with
drywall. Install Fireplace with framing
1/2” behind face of Fireplace (See Nailing
Tab Guide Section).
 Bottom of Fireplace must be raised
1/2” above floor or hearth to install
this surround.
1. Hook Bottom Ledge of Surround onto Lower Panel of Fireplace. 2. Attach Surround with [2] Screws provided.
Each kit contains:
- [Qty-1] Surround Frame
- [Qty-2] #6 Self Tapping Screws
Bottom Ledge of
Surround
Lower Panel of
Fireplace
Attach to Tile Lip with supplied Screws
Screw Holes
Lower Panel of Fireplace
34-7/8”
To Floor
Bottom of Fireplace must be raised 1/2” above floor
or hearth to provide clearance for Surround
20