Kirby Lester KL1 Configuration guide

5DIM‐3802‐DCI4/2016
DailyCleaningInstructions:KL1

Cleanthefollowingcomponentsatleastoncedaily.Cleanmorefrequentlyifyourpharmacy
dispensesmanydust‐generatingmedicationsorifyouexperiencecountingerrors.

Materials:70%isopropylalcoholormildsoapywater(e.g.,dishsoap),lint‐freeclothor
papertowels.Donotusefacialtissue,cottonballsorcottonswabs.

Beforestarting,turnofftheunitandunplugit.

1.Funnel
A. Removethefunnelfromtheunit.
B. Cleanoutsideandinsidethoroughlywithalcoholormildsoapywater.


2.GlassDetectorWindows
Theunit’scountingsensorsarelocatedbehindtheremovableinsidechannelassembly.
Mostcountingerrorsarecausedbypilldustaccumulatingontheedgesandcornersof
thewindowsonthechannelassembly.Cleanthewindowswell.

A. Unscrewthetworoundthumbscrewsontopoftheunit.Removethe
squareguard.
B. Liftouttheentireinsidechannelassembly.Donotremovetheindividualglasspanes
attachedtotheinsidechannelassembly.
C. Wipeoffexcesspilldustontheinsideofthefourcleardetectorwindowswith
adrycloth.
D. Wetacleanclothwithalcoholormildsoapywaterandcleantheinsideofthefour
glasswindowsthoroughlytoremoveallremainingdustandresidue.Wipeback‐and‐
forth,notup‐and‐down.Donotpresshardasthismaybreaktheglasswindows.Do
notremovetheindividualglasspanes.
E. Foldtheclothtoformanedgetocleananyedgedustcanaccumulate,especiallycorners.
F. Wipetheglasswindowsdrywithacleancloth.Holdthewindowsuptoalighttovisually
inspecttheglassforanydust,fingerprints,orstreaks.Re‐cleanifnecessary.Wipedry.
G. LookdowninsidetheKL1deviceandvisuallyinspectthefourinsideglasswindows
fordustorstreaks.Ifnecessary,cleanwithwaterandwipedry.
H. Replacetheinsidechannelassemblyandsquareguard.Tightentheroundthumb
screwsuntilsnug.Donotover‐tightenthethumbscrews.
StepA–Remove
SquareGuard
StepsC‐F,Inside
ChannelAssembly:
Cleaninsideand
outsideof4glass
windowswithout
removingor
damagingthepanes

5DIM‐3802‐DCI4/2016

I. Ifdesired,theglasswindowholdercanberemovedfromtheinsidechannel
assemblyforamorethoroughcleaningandvisualinspection.Gentlypushdownon
thesquareslidingtube,whichspreadsthetwoblackclipsholdingtheglasswindow
holder.Takespecialcarenottobreaktheblackclips.

3.CountingTray
Cleanthoroughlywithmildsoapywater.Donotusealcohol.


4.TraySensor
LocatedontheKL1behindthecountingtraywhenthetrayisfullyinserted.Thissensor
tellstheunitthatthetrayisproperlyseated.Withthetrayremoved,cleanthesensor
windowwithwater.Wipedrytoremovestreaks.




Noteabouttheuseofmildsoapywaterversusisopropylalcohol:Mildsoapywaterandalcoholboth
provideappropriatesanitarycleansing.WaterleavesfewerstreaksthanalcoholonaKirbyLester
device'sinsideglasssensorwindows.Ifstreaksarefoundaftercleaning,usejustwaterandwipedry.
Ingeneral,prolongedalcoholexposurecausesfasterwear‐and‐tearonplastic.

5.CleaningandTroubleshooting

ProblemorErrorCodeProbableCause PossibleSolution(s)
E‐2,E‐4,E‐9,O‐Sorunitcountsby
itself
Tabletdustorresidueonglassdetector
windows,orreplacecrackedglassdetector
window.
Cleanglassdetectorwindowsthoroughly.Or
replacecrackedglassdetectorwindow.
OvercountsTabletfragments,ortabletdustonglass
detectorwindows.
Checkcountedmedicationsfortablet
fragments.Cleanglassdetectorwindows
thoroughly.
UndercountsPouringtoofast,orpouringtabletsdirectly
intothefunnelhole.
Slowpouringspeedsothe“PourSlower”
indicatordoesnotactivate.
Displayreads"‐‐‐‐"insteadof
"0000"withtraypushedin
Traynotfullyinserted.Traysensorwindow
isdirty.
Cleantraysensorwindow.Fullyinserttray.

6.QuestionsorProblems
PleasecontactKirbyLesterServiceat800.243.2465or[email protected].


StepI–Visually
InspectWindows
TraySensor