Kleenmaid RHSOG91 Installation guide

cooking collection
Instructions for use and warranty details
Rangehood
0RGHO1RRHSOG61_RHSOG91

Dear Customer,
Thank you and congratulations for choosing
Kleenmaid.
Your new appliance has been designed
and meticulously tested to ensure that it
meets all your culinary requirements, and
has been carefully manufactured using top
quality materials to give you years of reliable
performance.
For best results, carefully read the instructions
on how your new appliance is to be installed.
Correct installation will avoid delays and
unnecessary service call costs.
Once installation is complete, please read this
instruction manual carefully and get to know
the controls and the features of your new
Kleenmaid appliance. These simple instructions
will enable you to achieve excellent results from
the very first time you use it.
Again, congratulations and thank you for
choosing The Best You Can Own.
KLEENMAID
2

Instructions for mounting and use
Closely follow the instructions set
out in this manual. All responsibility,
for any eventual inconveniences,
damages or fires caused by not
complying with the instructions in this
manual, is declined. This appliance is
intended to be used in household and
similar application such as: staff
kitchen areas in shop, offices and other
working environments,;farm houses,;
by clients in hotels, motels and other
residential type environments and;bed
and breakfast type environments.
Note: The parts marked with the
symbol "(*)" are optional accessories
supplied only with some models or
otherwise not supplied, but available for
purchase.
Caution
•Before any cleaning or maintenance
operation, disconnect rangehood from
the mains by removing the plug
or disconnecting the mains electrical
supply.
•Always wear work gloves for all
installation and maintenance operations.
•This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their well
being.
•Children should be supervised to ensure
that they do not play with the appliance.
•Cleaning and user maintenance should
not be performed by children without
supervision.
•There shall be adequate ventilation of
the room when the range hood is used at
the same time as appliances burning gas
or other fuels.
•The hood must be regularly cleaned on
both the inside and outside (AT LEAST
ONCE A MONTH).
•This must be completed in accordance
with the maintenance instructions
provided. Failure to follow the instructions
provided regarding the cleaning of the
rangehood and filters will lead to the risk of
fires.
•If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in
order to avoid a hazard.
•Do not flambé under the rangehood.
•For lamp replacement follow the
instructions in the Maintenance/Replacing
lamps section of this manual (page 13).
•The use of exposed flames is detrimental
to the filters and may cause a fire risk,
and must therefore be avoided in all
circumstances.
•Any frying must be done with care in
order to make sure that the oil does not
overheat and ignite.
•CAUTION: Accessible parts of the hood
may become hot when used with cooking
appliances.
•Do not connect the appliance to the
mains until the installation is fully
complete.
•With regards to the technical and safety
measures to be adopted for fume
discharging it is important to closely follow
the regulations provided by the local
authorities.
•The air must not be discharged into a
flue that is used for exhausting fumes
from appliance burning gas or other fuels.
•Do not use or leave the hood without
the lamp correctly mounted due to the
possible risk of electric shocks.
•Never use the hood without effectively
mounted grids.
•The hood must NEVER be used as a
support surface unless specifically
indicated.
•Use only the fixing screws supplied with
the product for installation or, if not
supplied, purchase the correct screws
type.
•Use the correct length for the screws
which are identified in the Installation
Guide.
•In case of doubt, consult an authorised
service assistance center or similar
qualified person.
WARNING!
,Failure to install the screws or fixing device
in accordance with these instructions may
result in electrical hazards.
,Do not use with a programmer, timer, separate
remote control system or any other device that
switches on automatically.
,This appliance is marked according to the
European directive 2012/19/EC0on Waste
Electrical and Electronic Equipment (WEEE).
,By ensuring this product is disposed of
correctly, you will help prevent potential
negative consequences for the environment
and human health, which could otherwise be
caused by inappropriate waste handling of this
product.
3

The symbol on the product, or on the
documents accompanying the product, indicates
that this appliance may not be treated as
household waste. Instead it should be taken to the
appropriate collection point for the recycling of
electrical and electronic equipment. Disposal
must be carried out in accordance with local
environmental regulations for waste disposal.
For further detailed information regarding the
process, collection and recycling of this product,
please contact the appropriate department of
your local authorities or the local department for
household waste or the shop where you
purchased this product.
Appliance designed, tested and manufactured
according to:
Safety: EN/IEC 60335-1; EN/IEC
60335-2-31, EN/IEC 62233.
Performance: EN/IEC 61591; ISO 5167-1; ISO
5167-3; ISO 5168; EN/IEC 60704-1; EN/IEC
60704-2-13; EN/IEC 60704-3; ISO 3741; EN
50564; IEC 62301.
EMC: EN 55014-1; CISPR 14-1; EN 55014-2;
CISPR 14-2; EN/IEC 61000-3-2; EN/IEC
61000-3-3.
Suggestions for correct use in order to reduce
the environmental impact:: Switch ON the hood
at minimum speed when you start cooking and
kept it running for few minutes after cooking is
finished. Increase the speed only in case of large
amount of smoke and vapor and use boost
speed(s) only in extreme situations. Replace the
charcoal filter(s) when necessary to maintain a
good odor reduction efficiency. Clean the grease
filter(s) when necessary to maintain a good
grease filter efficiency. Use the maximum
diameter of the ducting system indicated in this
manual to optimize efficiency and minimize noise.
WARNING!
Before re-connecting the hood circuit to
the mains supply and checking the
efficient functioning of the rangehood,
always check that the mains cable is
correctly assembled.
4

Installation
The hood is designed to be used either for exhausting or filter
version.
Ducting version
In this case the fumes are conveyed outside of the building by
means of a special pipe connected with the connection ring
located on top of the hood.
Attention!The exhausting pipe is not supplied and must be
purchased separately.
Diameter of the exhausting pipe must be equal to that of the
connection ring.
In the horizontal runs the exhausting pipe must be slightly
slanted (about 10°) and directed upwards to vent the air easily
from the room to the outside.
Attention! If the hood is supplied with active charcoal
filter, then it must be removed.
Connect the hood and discharge holes on the walls with a
diameter equivalent to the air outlet (connection flange).
Using the tubes and discharge holes on walls with smaller
dimensions will cause a diminution of the suction performance
and a drastic increase in noise.
Any responsibility in the matter is therefore declined.
!Use a duct of the minimum indispensible length.
!Use a duct with as few elbows as possible (maximum
elbow angle: 90°).
!Avoid drastic changes in the duct cross-section.
!Use a duct which is as smooth as possible inside.
!The duct must bemadeofcertified material.
Filter version
One active charcoal filter is needed for this and can
be obtained from your usual retailer.
The filter removes the grease and odours from the extracted
air before sending it back into the room through the upper
outlet grid.
Installation
Electrical connection
The mains power supply must correspond to the rating
indicated on the plate situated inside the hood. If providedwith a
plug connect the hood toasocket in compliance with current
regulations and positioned in an accessible area, after
installation. If it not fitted with a plug (direct mains connection) or
if the plug is not located in an accessible area, after
installation, apply adouble pole switch in accordance with
standards which assures the complete disconnection of the
mains under conditions relating toover-current category III, in
accordance with wiring rules.
Warning! Before re-connecting the hood circuit to the
mains supply and checking the efficient functioning of the
hood,always check that the mains cable is correctly assembled.
Mounting
Before beginning installation:
• Check that the product purchased is of asuitable size for
the chosen installation area.
•Remove the charcoal (*) filter/s if supplied (see also
relative paragraph). This/these is/are to be mounted only
if you want lo use the hood in the filtering version.
•Check (for transport reasons) that there is no other
supplied material inside the hood (e.g. packets with
screws (*), guarantees (*), etc.). If so, removeand
keep them.
•If possible, disconnect and move freestanding or slide-in
range from cabinet opening to provide easier access to
rear wall/ceiling. Otherwise put a thick, protective
covering over countertop, cooktop or range to protect
from damage and debris. Select aflat surface for
assembling the unit. Cover that surface with a protective
covering and place all canopy hood parts and hardware
onit.
•In addition check whether an electric socket is available
near the installation area of the hood and it is possible
to connect a fumes discharge device to the outside
(only suction version).
•Carry out all the masonry work necessary (e.g.
installation of an electric socket and/or a hole for the
passage of the discharge tube).
Expansion wall plugs are provided to secure the hood to most
types of walls/ceilings. However, a qualified technician must
verify suitability of the materials in accordance with the type of
wall/ceiling. The wall/ceiling must be strong enough to take
the weight of the hood. Do not tile, grout or silicone this
appliance to the wall. Surface mounting only.
This hood is designed for fitting in a cabinet or on some other
support.
5
The safety gap between the rangehood and the hob below
must comply with the recommendations of the hob
manufacturer. In case of no instructions, a minimum distance
of 650mm (or other minimum distance as may be specified by
AS/NZS 5601 and interpreted by a certified installer) should
apply.
Regulations concerning the discharge of air must be fulfilled.
Technical Information
Power Supply: 220-240V 50-60Hz
Total Absorbed Power: 120W
Motor:115W Lights: 2x2.5W

&

6

7

8

9

10

11

15
12

Operation
The hood is fitted with a control panel with aspiration
speed selection control and a light switch to control cooking
area lights.
a ON/OFF lighting
b-c ON/OFF motors
It is recommended that the rangehood suction is switched on for
5 minutes prior to cooking, be left in operation during cooking
and for approximately 15 minutes after terminating cooking.
Maintenance
ATTENTION! Before performing any maintenance operation,
isolate the rangehood from the electrical supply by switching off
at the connector and removing the connector fuse.
If the appliance has been connected through a plug and socket,
then the plug must be removed from the socket.
Cleaning
The hood must be regularly cleaned on both the inside and
outside (AT LEAST ONCE A MONTH). Clean using ONLY a
cloth dampened with neutral liquid detergent. DO NOT CLEAN
WITH TOOLS OR INSTRUMENTS. Do not use abrasive
products. DO NOT USE ALCOHOL!
Grease filter
The grease filter must be cleaned once a month using non
abrasive detergents, either by hand or in the dishwasher, which
must be set to a low temperature and a short cycle. When
washed in a dishwasher, the grease filter may discolor slightly,
but this does not affect its filtering capacity.
Charcoal filter (filter version only)
Fig. 13 on page 12
The saturation of the charcoal filter occurs after prolonged
use, with the time depending on the type of cooking and the
regularity of cleaning the grease filter.
In any case it is necessary to replace the cartridge at least
every four months. The charcoal filter must NOT be washed or
regenerated.
Replacing lamps
Fig. 15 on page 12
The hood is equipped with a lighting system based on LED
technology.
The LEDs guarantee for optimum lighting, a duration up to 10
times as long as the traditional lamps and allow saving up to
90% on electrical energy.
To replace lights, contact an authorised spare part centre.
13

KLEENMAID WARRANTY
TERMS AND CONDITIONS
1. Compass Capital Services Pty Ltd ABN 96 138 214 525 trading as Kleenmaid will provide parts and labour to you the
customer as set out herein.
2. Kleenmaid’s Products come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does
not amount to a major failure.
3. The benefits given to you under this Kleenmaid Warranty are in addition to other rights and remedies to which you may be
entitled under the Australian Consumer Law in relation to the Product to which this Kleenmaid Warranty relates. Subject to
the conditions below, the Product is warranted by Kleenmaid and/or its agents to be free from defects in materials and
workmanship for the Warranty Period for normal Domestic Use.
4. Product Identification: -
a. Kleenmaid reserves the right to reject claims for any services or work where you cannot produce for verification the
serial number and a proof of purchase for the Product (including but not limited to the original invoice).
b. this Kleenmaid Warranty will be voided if the serial number for the Product cannot be verified. This is not intended to
exclude, restrict or modify any right or remedy to which you may otherwise be entitled under the consumer guarantee
provisions of the Australian Consumer Law.
c. in the event that a request for repair is made against this Kleenmaid Warranty where the serial number for the Product
cannot be verified or you cannot produce for verification a proof of purchase for the Product (including but not limited to
the original invoice), the repairer will not carry out any repairs on the Product and you will be charged a service call-out
fee.
5. What is covered by this Kleenmaid Warranty: -
a. the Product is covered for faulty workmanship or parts that have failed under normal Domestic Use.
b. Kleenmaid and/or its agents will determine by objective testing if there are any defects in the Product and/or faulty
workmanship.
c. this Kleenmaid Warranty is only applicable if repairs on Products are carried out within Mainland Australia.
d. this Kleenmaid Warranty: -
i. covers a Product purchased as new, manufactured for use in Mainland Australia;
ii. commences from the date of delivery of the Product;
iii. provides for the labour and replacement parts necessary to maintain the Product in good operating condition as
specified in this Kleenmaid Warranty, however, if repair is needed because of Product failure during normal Domestic
Use, Kleenmaid has the option to repair or replace the defective Product or part of the Product with a product or part
of like kind and quality. A replacement part may be new or reconditioned of like kind and quality and may cost less
than the original Product purchased and no charges or refunds will be made based on the replacement product or
part cost difference; and
iv. is only applicable when the Product is used and operated in accordance with the Manufacturer’s instructions.
6. What is not Covered by this Kleenmaid Warranty (excluded):-
a. any damage or failure to or of the Product or part of the Product:
i. due to the Product being inadequately serviced to manufacturer’s recommendations;
ii. resulting from environmental conditions including and not limited to dirt, dust, rodents, insects, rust, corrosion, salt
built-up, of or in any part of the Product;
iii. resulting from excessive use but fair wear and tear is excepted;
iv. resulting from poor installation including and not limited to positioning and externally fitted equipment such as
plumbing and drainage, cabling, antennae or due to incompatibility of connected equipment;
v. caused by overheating as a result of sitting or positioning of the Product, where there is no provision for adequate
ventilation or adequate protection from excessive dust;
vi. if the Product has been dismantled, repaired or serviced by any person other than someone authorised by Kleenmaid
or its agents or representatives;
vii. caused by power surges or spikes, including and not limited to, mains power and telecommunications
connections, or to other unspecified sources, incorrect power current, voltage fluctuation, amperage fluctuation, rust
or corrosion;
viii. if the Product is dropped, collision of the Product with another object, use for which the Product is not designed,
damage to the Product caused by your own negligence, accidental or deliberate misuse of the Product by you, theft,
abuse, vandalism, flood, fire, earthquake, electrical storms or any other act of God or any war related events; or
ix. due to the introduction of abnormal heat loads to the Product;
b. costs of attendance and testing where no fault or defect covered by the terms of this Kleenmaid Warranty is identified in
the Product;
c. initial setup and installation of the Product;
d. normal maintenance costs and costs incurred through the installation of items listed as requiring periodic replacement;
e. Products with removed or altered serial numbers;
f. broken or cracked glass other than transport damage to the initial point of delivery;
g. consumables such as but not limited to bulbs/globes, seals, filters, batteries and remote controls;
h. removal and reinstallation of an internal component not performed by an authorised Kleenmaid agent or representative
or authorised service centre;
i. cosmetic or structural items; or
j. any failures due to interference from or with other products and/or sources.
7. This Kleenmaid Warranty ceases if: -
a. the Product ceases to carry the original manufacturer’s serial number or is sold at an auction;
b. the Product is rented; or
c. there is failure to pay monies owing on invoices as a result of non-warranty work being carried out at the request of the
end user as per point 16 below.
8. Neither Kleenmaid nor its representatives provide loan equipment under the terms of this Kleenmaid Warranty.
9. Any unauthorised access to the internal hardware of the Product will void this Kleenmaid Warranty.
14

10. Repair Notice: Products presented for repair may be replaced by refurbished Products of the same type rather than being
repaired. Refurbished parts may be used to repair the Products.
11. Replacement items are “like for like” and is not “new for old” and does not indicate in any way that a faulty Product will be
replaced with a new part or unit. “Like for like” may either be a quality checked, refurbished or reconditioned unit of the
same or later batch of model/size/specifications
12. The cost of making a claim under this Kleenmaid Warranty is not covered by Kleenmaid, including any costs of transportation
or travel expenses between your home and your nearest authorised service agent.
13. Kleenmaid accepts no liability for items that are lost, damaged, or stolen as a result of freight, transport or storage. If you are
required to transport the Product to an authorised service centre, you must ensure that it is securely packed and insured.
14. On Public Holidays or other periods when regular business and wholesale operations are temporarily ceased, repairer
availability and warranty response times may extend beyond the standard response times due to the unavailability of
repairers and parts.
15. For any repair performed on a Product under this Kleenmaid Warranty where no fault can be found, or the item is deemed by
Kleenmaid or an authorised agent, to be not faulty under this Kleenmaid Warranty, or the repair or fault is not covered under
this Kleenmaid Warranty, a ‘No Fault Found’fee is payable by you. Kleenmaid will advise you of this cost and seek your
agreement to pay such costs before commencing such repairs.
16. Any repairs or services required that are outside the terms and conditions of this Kleenmaid Warranty can be carried out at
your request at your cost (including where the Product has not been installed or set up correctly). Kleenmaid will always
advise you of this cost and seek your agreement to pay such costs before commencing such repairs. A credit card may be
required prior to the commencement of such services.
17. Extra charges will be payable by the customer should the Product not be readily accessible without special equipment, such
as but not limited to cranes and lifts or should the Product be installed in a position that service access is blocked and/or
repair work is not possible without uninstalling the Product to gain access.
18. You, the customer, may be entitled to purchase an extended warranty in respect of the Product. Any extended warranty will
not be issued by Kleenmaid but by a third party. Any extended warranty services will be provided directly by the third party as
principal and not as agent for Kleenmaid, under their extended warranty terms and conditions and not under this Kleenmaid
Warranty.
19. To make a claim under this Kleenmaid Warranty, please have your proof of purchase and the serial number of the Product
ready and call [phone] during business hours.
20. This Kleenmaid Warranty is given by:
Name: Compass Capital Services Pty Ltd ABN 96 138 214 525 trading as Kleenmaid
Business address: Level 2, Suite 3, 204 Botany Rd, Alexandria NSW Australia 2015
Telephone: [phone]
21. Definitions:
a. Australian Consumer Law means the Competition and Consumer Act 2010 (Cth).
b. Domestic Use means use of the Product for personal, domestic or household purposes.
c. Kleenmaid means Compass Capital Services Pty Ltd ABN 96 138 214 525 trading as Kleenmaid.
d. Mainland Australia means the following States and Territories of Australia: New South Wales, Victoria, South Australia,
Western Australia, Queensland, Tasmania, Northern Territory, Australian Capital Territory.
e. Product means the appliance sold by Kleenmaid to you as evidenced by the original purchase invoice.
f. Warranty Period means the period of 60 months for domestic use, 12 months for non-domestic use or such
alternative period as may be specified.
UPDATE NOTICE: This Kleenmaid Warranty is current as at 1 January 2019 but is subject to variation from time to time.
For the latest version of the Kleenmaid Warranty, please see our website
http://www.kleenmaid-appliances.com.au/support/your-kleenmaid-warranty or phone us on [phone].
15

Compass Capital Services Pty Limited
trading as Kleenmaid
ABN 96138214525
Level 2, 204 Botany Road Alexandria
NSW 2015
Other products available in the
Kleenmaid range of appliances
|Washing machines
|Clothes dryers
|Dishwashers
|Ovens
|Cooktops
|Steam ovens
|Microwave ovens
|Built in espresso
coffee machines
|Rangehoods
|Freestanding ovens
|
|
|
|
Refrigerators & Freezers
Beverage Serving Cabinets
Water Dispensers
Vacuum Cleaners
Register your Kleenmaid
Appliances Warranty
www.kleenmaidwarranty.com.au
Request a Warranty Service
www.kleenmaidwarranty.com.au
E: [email protected]
www.kleenmaid.com.au
V2