Kleenmaid RHWMDB40 User manual

cooking collection
Instructions for use and warranty details
Rangehood – 40cm
Model No.: RHWMDB40

3
Your new Kleenmaid appliance has been
designed and manufactured to give you
years of reliable performance.
For best results, carefully read the
instructions on how to install your new
appliance. Correct installation will avoid
delays and unnecessary service call costs.
Once installation is complete, please read
this entire instruction manual carefully and
get to know the controls and the features
of your new Kleenmaid appliance.
Again, congratulations and thank you for
choosing Kleenmaid.
Congratulations on the purchase
of your new Kleenmaid appliance.

4
X
1 x ø150
O
1 x ø120
X =
1X 2X
2 X
A
B

5
THIS PRODUCT IS DESIGNED FOR
DOMESTIC USE.
THE MANUFACTURER DECLINES
ALL RESPONSIBILITY FOR DAMAGES TO
THINGS OR PEOPLE DERIVING FROM
INCORRECT INSTALLATION OR IMPROPER,
ERRONEOUS OR UNSUITABLE USE.
THE APPLIANCE MUST NOT BE USED BY
PEOPLE (INCLUDING CHILDREN) WITH
PHYSICAL, SENSORIAL OR MENTAL
IMPAIRMENTS, OR BY PEOPLE WITHOUT
THE NECESSARY EXPERIENCE OR
KNOWLEDGE, UNLESS THEY ARE
SUPERVISED OR INSTRUCTED IN THE USE
OF THE APPLIANCE BY A PERSON
RESPONSIBLE FOR THEIR SAFETY.
CHILDREN MUST BE SUPERVISED TO
ENSURE THAT THEY DO NOT PLAY WITH
THE APPLIANCE.
Dear Customer,
We would like to thank you and congratulate
you on your choice.
This new product has been carefully designed
and built using top quality materials, and
meticulously tested to ensure that it meets all
your culinary requirements.
Please read and observe these simple
instructions, which will enable you to achieve
excellent results from the very first time you
use it. This state-of-the-art appliance comes
to you with our very best wishes.
THE MANUFACTURER

6
We recommend that you wear gloves during installation and maintenance.
When installing a vented version (the extracted air is sent outside = Fig. A), it is important to:
- prepare an air exhaust hole and duct with a diameter of 150 mm.
- use a duct that is as short as possible
- use a duct with the least number of curves possible (maximum curve angle 90°)
- avoid the use of flat ducts and ducts of different section as much as possible
- use a duct with the smoothest possible interior and conforming to the standard
- do not connect the rangehood to a duct that exhausts fumes produced by combustion (fireplaces, boilers, ovens, etc.)
- do not discharge the air into a cavity in the wall unless the cavity has been prepared for that purpose.
- provide the room with air intakes so that the hood does not create negative suction (no higher than 0.04 mbar).
When installing a recirculating version (the extracted air is returned to the kitchen = Fig. B) there is no need to prepare a
hole and exhaust duct, but you must provide two activated carbon filters (request them separately as an accessory).
Fig. 1: using the fixing bracket (1), mark the positions of the fastening holes on the ceiling.
Fasten using no. 2 anchors Ø 8 + no. 2 screws Ø 4.8x38 + no. 2 washers.
Fig. 2: attach the cover with grill (2) to the fixing bracket (1). (If you wish this cover can be omitted in the vented
version).

7
Fig. 3: adjust the telescopic section of the upper cylinder and fasten it to the bracket (1) using the two M4X12 screws
provided.
3°
X526
438
1100900 -
M
Fig.1
Fig.2
156
IMPORTANT: to fasten the rangehood tothe bracket that has previously been fastened to the wall, see detail (M); if you need
knto ow the height at which the rangehood must be positioned, see the measurements table.
X = 327 H = 1100
X = 227 H = 1000
The H900 does not need part 2
Variable rangehood height: 900 - 1000 - 1100

8
Fig. 4: mount the grease filter on the rangehood cylinder with the metal handle.
Fig. 5: position the glass with the smaller diameter facing down (A).
B
A

9
Fig. 6: hook the hinge (B) integrated into the glass to the hook of the male hinge C.
C
B
Fig. 7: slide the H26 Nylon spacer on the M6X40 screw provided and fasten it, by passing through the hole in the hole
in the glass, to the upper hole in the rangehood cylinder, tightening it by hand or using a tool or coin.
A

Fig. 8:
.)yrossecca
etarapesasadeilppus()D(sretlifnobracowttseuqertsumuoy,dellatsnigniebsirangehoodrecirculatingafi
Proceed to the insertion of the drawer-type carbon filter with the required type of slot system.
D
CONTROLS
AB C D E F G H I
A) starts/stops the motor at the second speed (the intermediate operating speed
B) selects the first motor speed
C) selects the second motor speed
D) selects the third motor speed
E) selects the fourth motor speed
F) turns on the halogen lamp: if held down, you can select 3 different levels of light. The last level selected is remembered for
the next time it is turned on.
G) turns on the timer (delayed turn-off): you can choose from 3 times (10’, 15’, 20’)
H) *Filter alarm (see detail)
I) remote-control receiver sensor