Kleenmaid RHWMDB40 Installation guide

3

4
X
1 x ø150
O
1 x ø120
X =
1X 2X
2 X
A
B

5
THIS PRODUCT IS DESIGNED FOR
DOMESTIC USE.
THE MANUFACTURER DECLINES ALL
RESPONSIBILITY FOR DAMAGES TO THINGS
OR PEOPLE DERIVING FROM INCORRECT
INSTALLATION OR IMPROPER, ERRONEOUS
OR UNSUITABLE USE.
THE APPLIANCE MUST NOT BE USED
BY PEOPLE (INCLUDING CHILDREN)
WITH PHYSICAL, SENSORIAL OR
MENTAL IMPAIRMENTS, OR BY PEOPLE
WITHOUT THE NECESSARY EXPERIENCE
OR KNOWLEDGE, UNLESS THEY ARE
SUPERVISED OR INSTRUCTED IN THE
USE OF THE APPLIANCE BY A PERSON
RESPONSIBLE FOR THEIR SAFETY.
CHILDREN MUST BE SUPERVISED TO
ENSURE THAT THEY DO NOT PLAY WITH THE
APPLIANCE.
Dear Customer,
we would like to thank you and congratulate
you on your choice.
This new product has been carefully designed
and built using top quality materials, and
meticulously tested to ensure that it meets all
your culinary requirements.
Please read and observe these simple
instructions, which will enable you to achieve
excellent results from the very first time you
use it. This state-of-the-art appliance comes
to you with our very best wishes.
THE MANUFACTURER

6
We recommend that you wear gloves during installation and maintenance.
When installing an extracting version (the extracted air is sent outside = Fig. A), it is important to:
- prepare an air exhaust hole and duct with a diameter of 150 mm.
- use a duct that is as short as possible
- use a duct with the least number of curves possible (maximum curve angle 90°)
- avoid the use of flat ducts and ducts of different section as much as possible
- use a duct with the smoothest possible interior and conforming to the standard
- do not connect the hood to a duct that exhausts fumes produced by combustion (fireplaces, boilers, ovens, etc.)
- do not discharge the air into a cavity in the wall unless the cavity has been prepared for that purpose.
- provide the room with air intakes so that the hood does not create negative suction (no higher than 0.04 mbar).
When installing a filtering version (the extracted air is returned to the kitchen = Fig. B) there is no need to prepare a
hole and exhaust duct, but you must provide two activated carbon filters (request them separately as an accessory).
Fig. 1: using the fixing bracket (1), mark the positions of the fastening holes on the ceiling.
Fasten using no. 2 anchors Ø 8 + no. 2 screws Ø 4.8x38 + no. 2 washers.
Fig. 2: attach the cover with grill (2) to the fixing bracket (1). (If you wish this cover can be omitted in the extracting
version).

7
Fig. 3: adjust the telescopic section of the upper cylinder and fasten it to the bracket (1) using the two M4X12 screws
provided.
3°
X526
438
1100900 -
M
Fig.1
Fig.2
156
IMPORTANT: to fasten the hood to the bracket that has previously been fastened to the wall, see detail (M); if you need to
know the height at which the hood must be positioned, see the measurements table.
X = 327 H = 1100
X = 227 H = 1000
The H900 does not need part 2
Variable hood height: 900 - 1000 - 1100

8
Fig. 4: mount the grease filter on the hood cylinder with the metal handle.
Fig. 5: position the glass with the smaller diameter facing down (A).
B
A

9
Fig. 6: hook the hinge (B) integrated into the glass to the hook of the male hinge C.
C
B
Fig. 7: slide the H26 Nylon spacer on the M6X40 screw provided and fasten it, by passing through the hole in the hole
in the glass, to the upper hole in the hood cylinder, tightening it by hand or using a tool or coin.
A

Fig. 8: .)yrosseccaetarapesasadeilppus()D(sretlifnobracowttseuqertsumuoy,dellatsnigniebsidoohgniretlifafi
Proceed to the insertion of the drawer-type carbon filter with the required type of slot system.
D
CONTROLS
A B C D E F G H I
A) starts/stops the motor at the second speed (the intermediate operating speed
B) selects the first motor speed
C) selects the second motor speed
D) selects the third motor speed
E) selects the fourth motor speed
F) turns on the halogen lamp: if held down, you can select 3 different levels of light. The last level selected is remembered for
the next time it is turned on.
G) turnson the timer (delayed turn-off): you can choosefrom 3 times (10’, 15’, 20’)
H) *Filter alarm (see detail)
I) remote-control receiver sensor