klimaoprema FDC25 Series User manual
1| re damper user manual 03/2020
Gradna 78A, 10430 Samobor
Croatia | Hrvatska
+385 (0)1 33 62 513
www.klimaoprema.hr
|
1. Product presentation.......................................................................................................2
2.Dimensionalrange............................................................................................................3
3. Dimensions.........................................................................................................................4
4. Storage and handling......................................................................................................6
5. Installation and implementation.................................................................................6
6. Control mechanism........................................................................................................21
7. Electrical connections....................................................................................................23
8. Other mechanisms.........................................................................................................25
9. Evolution of service kits...............................................................................................27
10.Maintenance...................................................................................................................27
2 3| re damper user manual 03/2020
steel sheet, damper blade is made of special insulating material, and damper blade shaft and
with solenoid actuator mechanism or with electric actuator mechanism..
•
•
•
blocks wall
•
•
• Maintenance free
1. Galvanized steel casing
2. Fire resistant damper blade
3. Control mechanism
4. Intumescent joint
6. Product marking on the casing
2. Intumescent joint
3. Cold smoke seal
1
3
4
5
2
6
7
1
2
3
4
(dm²)
blade 40mm) (dm²)
(m²)
blade 40mm) (m²)
Diameter (mm) Gross section (dm²)
FDC25
100 0,74 0,50
125 1,17 0,87
160 1,93 1,55
200 3,05 2,56
250 4,79 4,18
300 6,18 5,74
315 7,64 6,87
FDC40
355 9,73 8,33
400 12,37 10,79
450 15,69 13,91
500 19,39 17,41
630 30,86 28,36
710 39,24 36,42
800 49,86 46,68
Diameter (mm) Gross section (dm²)
FDC
100 3,30 0,50
125 3,80 0,87
160 5,11 1,55
200 6,16 2,56
250 8,55 4,18
315 12,25 6,87
5| re damper user manual 03/2020
380 ∅D/2+12 ∅D/2+22
220
Y
D
AC
D
∅D
E
380 ∅D/2+12 ∅D/2+22
∅D
Y
101
E
A
E
Y
D
AC ∅D
380 ∅D/2+12
C
∅D/2+22
∅D
380 100 45
∅D+A
(∅D/2)+80 (∅D/2)+94
(∅D/2)+80 (∅D/2)+124
380 100 45
∅D
∅D+A
45
∅D+A
380
145
∅D+160
45
∅D+A
380
145
∅D+160
(∅D/2)+80 (∅D/2)+124
380 100 45
∅D
∅D+A
∅D
380 100 45
∅D+A
(∅D/2)+80 (∅D/2)+94
FDC25-R
Product A C D E
Belimo BFL (M) 25 200 90 120
25 225 100 120
Klimaoprema
55 150 105 150
55 200 105 200
55 200 105 200
100 Øn+105mm
Øn+95mm
Øn+80mm
*(dimension X is same as Y
(blade lenght outside of housing)
but on opposite side
6 7| re damper user manual 03/2020
attention to:
•
•
• do not use the damper as a workbench or scaffolding
•
sunlight to prevent premature aging of the thermal fuse. Once the damper is installed, the
wedging and caulking during the sealing of the dampers must not cause deformations that will
alter the good functioning of the damper and in particular the closing of the blade.
•
•
•
•
accordance with the technical manual
•
•
Opening size – A (minimum)
ØD < 160 ØD + 85
180 < ØD < 315 ØD + 75
315 < ØD < 450 ØD + 65
ØD > 450 ØD + 55
³) and with a minimum
thickness of 100 mm.
³ and a minimum
thickness of 100 mm
Place the damper in an opening
according to table (on pg. 6)
screws (screw hole is 6mm in
diameter)
Fill the space between the damper
and the wall with mortar
Place the damper in an opening
according to table
(on pg. 6)
screws (screw hole is 6mm in
diameter)
Fill the space between the damper
and the slab with mortar
8 9| re damper user manual 03/2020
³), and with minimum thickness
of 70mm.
³), and with minimum thickness
of 100mm.
Place the damper in an opening
according to table (on pg. 6)
(12,5mm thick) to wall with screws
(screw hole is 6mm in diameter)
Fill the space between the damper
and the wall with mortar
boards (12,5 mm thick)
all dimensions and must
dimensions of the damper
Diameter of the
damper (mm) Mounting kit
100 60061429
125 60061430
160 60061431
200 60061432
250 60061433
315 60061435
355 60061436
400 60061437
450 60061438
500 60061439
560 60061440
630 60061441
710 60061442
800 60061443
screws (screw hole is 6mm in
diameter)
Fill the space between the damper
and the wall with mortar
boards (12,5 mm thick)
Place the damper in an opening
according to table (on pg. 6)
all dimensions and must
dimensions of the damper
Diameter of the
damper (mm) Mounting kit
100 60061429
125 60061430
160 60061431
200 60061432
250 60061433
315 60061435
355 60061436
400 60061437
450 60061438
500 60061439
560 60061440
630 60061441
710 60061442
800 60061443
11 | re damper user manual 03/2020
construction of 48 mm width.
625 625
> 440
construction Place the damper in an opening
according to table (on pg. 6)
screws (screw hole is 6mm in
diameter)
Fill the space between the damper
and the wall with mineral wool (100
Cover the mineral wool with GKF
625 625
> 440
construction
Place the damper in an opening
according to table
(on pg. 6)
screws (screw hole is 6mm in
diameter)
Fill the space between the damper
and the wall with mortar
boards (12,5 mm thick)
all dimensions and must
dimensions of the damper
Diameter of the
damper (mm) Mounting kit
100 60061429
125 60061430
160 60061431
200 60061432
250 60061433
315 60061435
355 60061436
400 60061437
450 60061438
500 60061439
560 60061440
630 60061441
710 60061442
800 60061443
all dimensions and must
dimensions of the damper
Diameter of the
damper (mm) Mounting kit
100 60061429
125 60061430
160 60061431
200 60061432
250 60061433
315 60061435
355 60061436
400 60061437
450 60061438
500 60061439
560 60061440
630 60061441
710 60061442
800 60061443
12 13 | re damper user manual 03/2020
Installation material: Fire damper FDC, Mineral wool >140kg/m³
400mm, but openings from Ø +
80…600 mm can also be used
Damper blade must be closed
during installation!
Space between casing and wall
mm thick, coated on one side)
Connections of mineral wool seal
must be coated with
protection coating
³
700
Øn+80
Øn+80
Place the damper in an opening
according to table (on pg. 6) (wall
Place ventilation duct trough wall
(thickness of threaded rod for
suspension should be M12 or more)
Fill space between duct and wall with
mineral wool (Isover U protect, min.
with Isover BSF in thickness of 1mm
the other side. Place the wool on
ventilation duct in lenght of 80mm
200mm distance between them
Place steel protection on place where
1mm thick metal sheet cover)
glue Isover BSK in thickness of 2mm
15 | re damper user manual 03/2020
³), and with minimum thickness
of 70mm.
30
30
30
45º
30
150
150
Prepare opening in the wall
according to dimension table (on
page 6)
Fire damper can be installed with
minimal distance of 30 mm between
wall, ceiling or other dampers.
boards (12,5 mm thick)
Space between casing and wall
close with mortar
³) and with a
minimum thickness of 100 mm.
Ø+ 400mm, but openings from
Ø + 80…600 mm can also be used
Damper blade must be closed
during installation!
Space between casing and wall
mm thick, coated on one side)
Connections of mineral wool should be
wool and damper casing must be coated with
1
3
2
1
45
Dn + 70
Dn + 70
Wall installation Ceiling installation
galvanized steel
Washer, galvanized steel
galvanized steel
secured with self tapping
screw to damper housing
1
2
3
4
5
16 17 | re damper user manual 03/2020
of 100mm.
³) and with a minimum
thickness of 100 mm.
30
30
30
45º
30
Prepare opening in the wall
according to dimension table
(on page 6)
30
30
30
45º
30
150
150
Prepare opening in the wall
according to dimension table
(on page 6)
Fire damper can be installed with
minimal distance of 30 mm between
wall, ceiling or other dampers.
boards (12,5 mm thick)
Space between casing and wall
close with mortar
Fire damper can be installed with
minimal distance of 30 mm between
wall, ceiling or other dampers.
Space between casing and wall
close with mortar
18 19 | re damper user manual 03/2020
30
30
30
45º
30
³) and with a minimum
thickness of 100 mm.
30
30
30
45º
30
Prepare opening in the wall
according to dimension table
(on page 6)
Fire damper can be installed with
minimal distance of 30 mm between
wall, ceiling or other dampers.
Space between casing and wall
close with mortar
according to drawing. Prepare
opening in the wall according to
dimension table (on page 6)
Mineral wool and damper casing
protection coating
Space between casing and wall
Fire damper can be installed with
minimal distance of 30 mm between
wall, ceiling or other dampers.
21 | re damper user manual 03/2020
³
5.2.1
³ and a minimum thickness
of 100 mm.
Installation hole is Øn + A + 10
mm (see page 5)
and fasten with screws
625 625
n +A
n +A
Installation hole is Øn + A + 10
and fasten with screws
Wall opening dimensions
100 Øn+105 Øn+115mm
Øn+95mm Øn+105mm
Øn+80mm Øn+90mm
•
• Manual triggering is possible
• Manual reset, use the screwdriver (turn counterclockwise)
and turn counterclockwise
head with a screwdriver
• electric limit switch indicating CLOSED position
•
Activation :
• Manual activation: Push the release button.
•
•
22 23 | re damper user manual 03/2020
and turn counterclockwise
head with a screwdriver
•
• electric limit switch indicating CLOSED position
•
• additional electric limit switch indicating CLOSED position
•
Activation:
• Manual activation: Push the release button.
•
•
voltage)
•
•
•
• Electrical wiring of the S option
Electronic control board
(automatic change on the electronic card)
Power
• Break of current: Pnom = 1.6W
1mA…500mA,
Blade closure time
Blade opening time Spring: 1 second
Manual Spring: 1 second
Degree of protection IP 42 IP 42
25 | re damper user manual 03/2020
Damper is delivered in closed position. When
electric actuator is connected to the power
reaches the end position (damper open), the
a temperature of 72 °C (inside or outside duct).
If checking is needed for proper functioning of
tripping device will close damper. When switch
on tripping device is released, the damper will
open.
Damper can be opened without connecting
to a voltage with enclosed handle turning in
the direction of the arrow on electric actuator
(clockwise). Damper can be locked in the desired
actuator will not move the damper into closed
position after power failure.
1
2
S1 common micro switch closed damper
S2
S3
S4 common micro switch open damper
S5
S6
voltage /
power con
sumption
voltage
50/60Hz
50/60Hz
50/60Hz
50/60Hz
50/60Hz
50/60Hz
opening 2,5 W 4 W 3,5 W 5 W 7 W 8.5 W
holding 0,8 W 1,4 W 1,1 W 2,1 W 2 W 3 W
for wire sizing
End switch
1 mA...3
A (0,5 A),
1 mA...3
A (0.5 A),
1 mA...3
A (0.5 A),
1 mA...3
A (0.5 A),
1 mA...6 A
(3 A), DC
1 mA...3
A (0.5 A),
time
motor <60 s <60 s <60 s <60 s <120 s <120 s
~20 s ~20 s ~20 s ~20 s ~16 s ~16 s
Ambient temperature range
Damper is delivered in closed position. When
damperwill open. When the damper reaches
the end position(damper open), in which is it
break at a temperature of 72 °C (inside or outside
duct). If checking is needed for proper unctioning
tripping device will close damper. When switch on
tripping device is released, the damper will open.
Damper can be opened without connecting to a
direction of the arrow on electric actuator
will go to closed position.
26 27 | re damper user manual 03/2020
•
• Provide at least one annual check of the damper
•
and its movable plate
• Check the if the electrical terminals are tightened
Designation Code
Fuse kit
Double contact S kit
Upgradeable to solenoid
Solenoid current break kit
1. Unique identification code of the product-type: Circular fire damper
2. Identification of the construction product: FDC25/40
3. Intended use(s) of the construction product: Circular fire damper to be used in conjunction with fire separating elements to maintain fire compartments in HVAC installations.
4. Name and contact address of the manufacturer: Klimaoprema d.d., Gradna 78A, 10430 Samobor
5. Not applicable
6. System of assessment and verification of constancy of System 1
performance of the construction proudct
7. In case of the declaration of performance concerning a The notified body 1812 carried out the initial inspection of the manufacturing plant and of the factory
construction product covered by a harmonised standard: production control as well as the continous surveillance, assessment and evaluation of factory production
control under system 1 and issued the Certificate of constancy of performance 1812 - CPR - 1161
8. Not applicable
9. Declared performance according to EN 15650: (Fire resistance according to EN 1366‐2 and classifications according to EN 13501‐3)
Essential characteristics Performance
Range Supporting construction Supporting construction details Type of installation Classification
FDC 40 ( ф100 -
ф630mm) Flexible wall
Type of installation: remote from wall, 0-180⁰
Nominal activation conditions/sensitivity according to ISO 10294-4: Passed
- sensing element load bearing capacity
- sensing element response temperature
Response delay (closing time) according to EN 1366-2: Passed
Operational reliability (opening, closing) according to EN 1366-2: Passed
Durability of response delay according to ISO 10294-4: Passed
- sensing element response to temperature and load bearing capacity
Durability of operational reliability (opening and closing cycle) according to EN 15650: Passed
- Belimo, Schischek, Siemens - 10 000 cycles
- Fuse only, Fuse + electromagnet (Klimaoprema) - 300 cycles
Protection against corrosion according to EN 60068-2-52: NPD
Damper blade and casing leakage according to EN 1751: Class ≥C
10. The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 7.
This declaration of performanse is issued under the sole responsibilty of the manufacturer identified in point 4.
Signed for on behalf of the manufacturer by:
Sergio Galošić, General manager
Samobor, 27. March 2018
EI 120 (ve i↔o)S (500Pa)
EI 90 (ve i↔o)S (300Pa)
EI 120 (ve i↔o)S (500Pa)
EI 120 (ve i↔o)S (500Pa)
EI 90 (ve i↔o)S (300Pa)
DECLARATION OF PERFORMANCE
No: DoP 711/2019_8_EN
Gypsum plaster/Mortar
WEICHSCHOTT
Mineral wool + cover boards
ф100 - ф800mm
Aerated concrete (≥550kg/m3) ≥100mm and
reinforced concrete (≥2200kg/m3) ≥100mm EI 90 (ve i↔o)S (500 Pa)
Plasterboard type 98/48 ≥100mm
EI 120 (ve i↔o)S (500 Pa)
Floor/ceiling Aerated concrete (≥550kg/m3) ≥100mm and
reinforced concrete (≥2200kg/m3) ≥100mm
EI 90 (ve i↔o)S (300Pa)
Gypsum plaster/Mortar
Harmonised standard EN 15650:2010
Gypsum plaster/Mortar + cover boards
Plasterboard type 98/48 ≥100mm EI 60 (ve i←o)S (300 Pa)Isover (remote from wall)
EI 90 (ve i↔o)S (500 Pa)
Type of installation: built in, APPLIQUE 0-360⁰ Minimal distances authorised.
EI 90 (ve i↔o)S (500 Pa)
Flexible wall
ф100 - ф315mm
WEICHSCHOTT
Gypsum plaster/Mortar + cover boards
Mineral wool + cover boards
WEICHSCHOTT
Aerated concrete (≥550kg/m3) ≥100mm and
reinforced concrete (≥2200kg/m3) ≥100mm
APPLIQUE (installation frame)
Rigid wall
Flexible wall
Gypsum blocks (≥995kg/m3) ≥70mm
Gypsum blocks (≥995kg/m3) ≥70mm
Plasterboard type 98/48 ≥100mm
Rigid wall
Other manuals for FDC25 Series
3
This manual suits for next models
7
Table of contents
Other klimaoprema Fire And Smoke Damper manuals
klimaoprema
klimaoprema RKP-P-N User manual
klimaoprema
klimaoprema FSD User manual
klimaoprema
klimaoprema FDC Series User manual
klimaoprema
klimaoprema FDC25 Series User manual
klimaoprema
klimaoprema FDC25 Series User manual
klimaoprema
klimaoprema FD User manual
klimaoprema
klimaoprema FD25 User manual
klimaoprema
klimaoprema FD25 User manual
klimaoprema
klimaoprema FD25 User manual
klimaoprema
klimaoprema FDSD User manual
Popular Fire And Smoke Damper manuals by other brands
System air
System air FDR-3G KR Series Handbook
Rf-t
Rf-t KAMOUFLAGE MP Series manual
System air
System air fantech bathfan Select SC50-80-110 installation instructions
Lindab
Lindab WK45 Series Installation booklet
Komfovent
Komfovent UVS60 M installation instructions
JRClancy
JRClancy 016-410L installation instructions
Lindab
Lindab WK45 Series Technical manual
HVC
HVC NCA 700 Series Operation and maintenance manual
Mandik
Mandik FDMB Technical documentation
Greenheck
Greenheck FD Series Installation instruction supplement
Komfovent
Komfovent UVA30-D-t installation instructions
Johnson Controls
Johnson Controls BD-1300 installation instructions
actionair
actionair SmokeShield Installation Methods
Mandik
Mandik FDMR 60 manual
Mandik
Mandik RKM Instructions for use
ETS NORD
ETS NORD NORDfire manual
Advanced Air
Advanced Air 2530 Installation, operation and maintenance manual
Greenheck
Greenheck FSDR Series Installation, operation and maintenance manual