klimaoprema FSD User manual

Gradna 78A, 10430 Samobor, Croatia
[phone]
[email protected]
www.klimaoprema.com
Projektiranje, proizvodnja i održavanje opreme za klimatizaciju, ventilaciju i čiste prostore.
Design, production and service of Ventilation, Air-Conditioning and Cleanroom equipment.
Product manual
Gradna 78A, 10430 Samobor, Croatia
[phone]
[email protected]
www.klimaoprema.com
Projektiranje, proizvodnja i održavanje opreme za klimatizaciju, ventilaciju i čiste prostore.
Design, production and service of Ventilation, Air-Conditioning and Cleanroom equipment.
Fire protection
FSD
Smoke control damper
Product manual
Version 1.0.2
Issue Date: 07.03.2023.

2
PRODUCT OVERVIEW
DIMENSIONS
INSTALLATIONS
ACTUATORS
ACCESSORIES
MAINTENANCE AND OPERATION
FSD SMOKE CONTROL DAMPER
1. Blades
2. Casing
3. Actuator
1. Side seal
2. Blade seal
3. Cover of the actuator encasing
PRODUCT OVERVIEW
Smoke control dampers FSD are used in smoke extraction
systems for extraction of smoke gases or providing supply air to
one or more fire compartments. Smoke control dampers consist
of calcium silicate casing and calcium silicate damper blade.
Calcium silicate blade is equipped with galvanized steel shaft
and with seals. Seals are made out of silicon and of intumescent
material. Smoke control dampers FSD are produced in sizes from
200x240 till 1200x2040 mm and are equipped with Belimo
actuator in version 24V or 230V.
Activation of smoke control dampers equipped with
electric actuator can be via smoke detector or remotely via control
signal. Rearming of the electric smoke damper can also be done
remotely via control signal. All electric actuators are equipped
with end switches for position signalling.
In case of smoke detection the actuator is triggered by a signal.
The signal can come either from a duct smoke detector or
from a fire alarm system. FSD smoke control damper have two
safe positions: open and closed. Depending on the fire site
and the path of the smoke to be extracted, the safe position is
either “open” or “closed”. The blades of FSD move to the safe
position when receiving an automatically or manually triggered
control signal.
FSD smoke control damper complies with the requirements
of EN 12101-8, and is tested to EN 1366-10 and EN 1366-2.
Classification of damper is EI 120/90 (vedw-hodw, i↔o) S1000
C10000 HOT 400/30 MA multi.
2
13
12
3
PRODUCT OVERVIEW

3
PRODUCT OVERVIEW
DIMENSIONS
INSTALLATIONS
ACTUATORS
ACCESSORIES
MAINTENANCE AND OPERATION
FSD SMOKE CONTROL DAMPER
CLASSIFICATION
FSD smoke control damper is tested according to EN 1366-10
“Fire resistance tests for service installations - Smoke control
dampers” and EN 1366-2 “Fire resistance tests for service
installations – Fire dampers”.
Classification of the FSD smoke control dampers is defined
according to EN 13501-4 “Fire classification of construction
products and building elements using data from fire resistance
tests”
Classification of FSD smoke control damper is:
EI 120/90 (vedw-hodw, i↔o) S1000 C10000 HOT 400/30
MA multi
Smoke damper should be installed according installation
manual which can be found within this document.
Please consult latest Declaration of Performance on our
website:
For more information about certificates, visit our website:
www.klimaoprema.com/fsd
E- Integrity
I- Insulation
120/90 - Classification time in minutes
ve - Damper installed in vertical position
ho - Damper installed in horizontal position
i↔o- Fire performance criteria are met on both sides
S- Smoke leakage
C- 10 000 Cycles
MA - manual intervention, can be used also as an AA classified
control damper
MULTI- usage in compartments classified as “multi”, can be
used aslo in compartments classified as “single”
www.klimaoprema.com/fsd/dop
PRODUCT OVERVIEW

4
PRODUCT OVERVIEW
DIMENSIONS
INSTALLATIONS
ACTUATORS
ACCESSORIES
MAINTENANCE AND OPERATION
FSD SMOKE CONTROL DAMPER
Pressure drop values are described with the “Zeta” values for each size. The exact pressure drop
in [Pa] is calculated using the following formula:
Product label
1 - Manufacturer
2 - Serial number
3 - Production date
4 - Type
5 - Dimension
6 - Mechanism type
7 - Nominal voltage
8 - Signalisation (end contacts)
9 - IP protection
10 - Free space
11 - Number of the European standard and
year of its publication
12 - Declaration of performance
13 - Classification according to EN13501-4
14 - Barcode
15 - CE mark
TECHNICAL DATA
2
3
4
5
6
1
7
15
11
9
10
12
13
14
Nominal sizes
FSD
200x240 - 1200x2040 [mm]
Casing length 250 mm
Temperature
range
-30 °C ... 50 °C
Volume flow
rate range
up to 82080 m³/h
Pressure level 2 -1000 up to 500 Pa
Casing air
leakage
Class C, EN 1751
EC conformity EU Construction Products Regulation no. 305/2011
EN 12101-8 – Smoke and heat control systems
EN 1366-10 – Fire resistance tests for service installations
EN 1366-2 – Fire resistance tests for service installations
EN 13501-4 – Fire classification of construction products and build-
ing elements – Fire resistance tests on components of smoke control
EN 1751 – Ventilation for buildings – Air terminal devices
Product specifications Pressure drop tables
8
16
2
3
4
5
6
1
7
15
11
9
10
12
13
14
8
16
LOCATION:
PRODUCTION DATE
SIGNALISATION
THIS DAMPER SHALL BE INSTALLED AS PER THE MANUFACTURER'S INSTRUCTIONS
IP PROTECTION:
23
1396-CPR-0227
NOMINAL VOLTAGE:
ACT. MECHANISM:
TYPE:
DIMENSION:
For fire classification of product
consult declaration of performance.
Smoke control damper
Multi compartment
EN12101-8:2011
El 120/90 (vedw, hodw i <->o)S1000 C10.000 HOT 400/30 MA multi
FREE SPACE (dm2):
Leakage rated
SERIAL NUMBER:
Yes
400x440
AC/DC 24V
07.03.2023
FSD-400x440-M24-S
M24
202926800100001
IP54
12,12
DOP 1715-1/2023
202926800100001
USER MANUALS
2
3
4
5
6
1
7
15
11
9
10
12
13
14
8
PRODUCT OVERVIEW
Zeta values
HxB 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000 1050 1100 1150 1200
240 0,658 0,637 0,624 0,614 0,608 0,602 0,598 0,595 0,592 0,59 0,588 0,586 0,585 0,583 0,582 0,581 0,58 0,579 0,579 0,578 0,577
440 0,586 0,568 0,556 0,548 0,542 0,537 0,533 0,53 0,528 0,526 0,524 0,522 0,521 0,52 0,519 0,518 0,517 0,516 0,516 0,515 0,515
640 0,554 0,536 0,525 0,517 0,512 0,507 0,504 0,501 0,499 0,497 0,495 0,493 0,492 0,491 0,49 0,489 0,488 0,488 0,487 0,487 0,486
840 0,535 0,518 0,508 0,5 0,494 0,49 0,487 0,484 0,482 0,48 0,478 0,477 0,476 0,475 0,474 0,473 0,472 0,471 0,471 0,47 0,47
1040 0,523 0,507 0,496 0,489 0,483 0,479 0,476 0,473 0,471 0,469 0,468 0,466 0,465 0,464 0,463 0,462 0,462 0,461 0,46 0,46 0,459
1240 0,515 0,499 0,488 0,481 0,476 0,472 0,468 0,466 0,464 0,462 0,46 0,459 0,458 0,457 0,456 0,455 0,454 0,453 0,453 0,452 0,452
1440 0,509 0,493 0,482 0,475 0,47 0,466 0,463 0,46 0,458 0,456 0,455 0,453 0,452 0,451 0,45 0,449 0,449 0,448 0,447 0,447 0,446
1640 0,504 0,488 0,478 0,471 0,465 0,461 0,458 0,456 0,454 0,452 0,45 0,449 0,448 0,447 0,446 0,445 0,444 0,444 0,443 0,443 0,442
1840 0,5 0,484 0,474 0,467 0,462 0,458 0,455 0,452 0,45 0,448 0,447 0,446 0,445 0,444 0,443 0,442 0,441 0,44 0,44 0,439 0,439
2040 0,496 0,48 0,47 0,463 0,459 0,455 0,452 0,448 0,446 0,444 0,444 0,443 0,442 0,441 0,44 0,439 0,438 0,436 0,437 0,435 0,436
Δp [Pa]= ζ* v² * 0,6
* ζis Zeta value from the tables below, v is airflow velocity in [m/s]

5
PRODUCT OVERVIEW
DIMENSIONS
INSTALLATIONS
ACTUATORS
ACCESSORIES
MAINTENANCE AND OPERATION
FSD SMOKE CONTROL DAMPER
Ordering key
MODELS
• Smoke control damper is used in smoke
extractsystems and is certified for installation in a
wall or duct.
• Produced according to standard EN 12101-8 and
tested according to EN 1366-10 and EN 1366-2
norms for smoke control systems
• Smoke control dampers come in dimensions from
200x240 mm till 1200x2040 mm. Volume flows
up to 82080 m3/h with airflow velocities up to 12
m/s.
• Damper casing is produced out of rigid, thermally
stable calcium silicate material
(1) Damper type (2) Dimension (3) Actuator type
FSD - BxH - M24-S
(1)
(2)
(3)
FSD
Dimensions
200x240 - 1200x2040
Actuator type:
M230-S - electric actuator AC/DC 230 V
M24-S - electric actuator AC/DC 24 V
M24-S-ST - electric actuator AC/DC 24 V
with connection plug
Actuators
Belimo BEN, BEE and BE actuators are used specifically for
smoke control dampers. Type of the model used depends on
the size of the smoke control damper.
M230-S
Belimo 230 V operation is controlled via 2-wire open/close
control. The actuator is overload-proof and can thus remain
energized even at the end stops. The Safety Position Lock™
reliably holds the smoke control damper in the defined safety
position in case of fire, thus ensuring maximum safety. The
hand crank included in the shipment can be used for man-
ual operation of the actuator. Two micro-switches with fixed
settings are installed in the actuator for indicating the damper
end positions. It should be noted with this application howev-
er that the contacts can no longer be used in the milliampere
range after larger currents have been applied to them, even
if this has taken place only once.The position of the damper
blade can be read off on a mechanical position indication
M24-S
Belimo 24V operation is controlled via 2-wire open/close
control. The actuator is overload-proof and can thus remain
energized even at the end stops. The Safety Position Lock™
reliably holds the smoke control damper in the defined safety
position in case of fire, thus ensuring maximum safety. The
hand crank included in the shipment can be used for man-
ual operation of the actuator. Two micro-switches with fixed
settings are installed in the actuator for indicating the damper
end positions. It should be noted with this application howev-
er that the contacts can no longer be used in the milliampere
range after larger currents have been applied to them, even
if this has taken place only once. The position of the damper
blade can be read off on a mechanical position indication
M24-S-ST
Belimo 24V operation is controlled via 2-wire open/close
control. The actuator is overload-proof and can thus remain
energized even at the end stops. The Safety Position Lock™
reliably holds the smoke control damper in the defined safety
position in case of fire, thus ensuring maximum safety. The
hand crank included in the shipment can be used for man-
ual operation of the actuator. Two micro-switches with fixed
settings are installed in the actuator for indicating the damper
end positions. It should be noted with this application howev-
er that the contacts can no longer be used in the milliampere
range after larger currents have been applied to them, even
if this has taken place only once. The position of the damper
blade can be read off on a mechanical position indication
The actuator is fitted with connection plugs. This means that
it can be integrated via communication and the power supply
unit in the control and monitoring system SBSE-Control.
PRODUCT OVERVIEW

6
PRODUCT OVERVIEW
DIMENSIONS
INSTALLATIONS
ACTUATORS
ACCESSORIES
MAINTENANCE AND OPERATION
FSD SMOKE CONTROL DAMPER
FSD
Dimensions
DIMENSIONS
B
B+380
H
H+80
250
290
250
Weight [kg]
HxB 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000 1050 1100 1150 1200
240 24.6 25.8 27 28,2 29,4 31,7 32,9 34 35,2 36,4 37,6 39,9 41,1 42,3 43,4 44,6 45,8 47 49,3 50,5 51,7
440 34 36,4 37,6 38,7 41,1 42,3 44,6 45,8 48,1 49,3 51,7 52,8 55,2 56,4 57,5 59,9 61,1 63,4 64,6 66,9 68,1
640 43,4 45,8 48,1 50,5 51,7 54 56,4 58,7 59,9 62,3 64,6 66,975 68,1 70,5 72,8 75,2 76,3 78,7 81 83,4 84,6
840 54 56,4 58,7 62,2 63,4 65,8 68,1 71,6 72,8 75,2 77,5 81,075 82,2 84,6 88,1 90,4 91,65 94 97,5 99,8 102,2
1040 63,4 65,8 69,3 71,6 74 77,5 79,9 82,2 85,7 88,1 90,4 94 96,3 98,7 102,2 104,5 106,9 110,4 112,8 115,1 118,6
1240 72,8 76,3 78,7 82,2 85,7 88,1 91,6 95,1 97,5 101 104,5 106,9 110,4 113,9 116,3 119,8 122,2 125,7 129,2 131,6 135,1
1440 83,4 85,7 89,3 92,8 96,3 99,8 103,4 106,9 110,4 113,9 117,5 121 124,5 128 131,6 135,1 137,4 141 144,5 148 151,5
1640 92,8 96,3 99,8 103,4 108,1 111,6 115,1 118,6 123,3 126,9 130,4 133,9 138,6 142,1 145,7 149,2 152,7 157,4 160,9 164,5 168
1840 102,2 106,9 110,4 115,1 118,6 123,3 126,9 131,6 135,1 139,8 143,3 148 151,5 156,2 159,8 164,5 168,0 172,7 176,2 180,9 185
2040 111,6 116,3 121 125,7 130,4 133,9 138,6 143,3 148 152,7 157,4 160,9 165,6 170,3 175 179,7 183,3 188 192,7 197,4 202,1

PRODUCT OVERVIEW
DIMENSIONS
INSTALLATIONS
ACTUATORS
ACCESSORIES
MAINTENANCE AND OPERATION
7
FSD SMOKE CONTROL DAMPER
Actuator types per dimension
HxB 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000 1050 1100 1150 1200
240
440
640
840
1040
1240
1440
1640
1840
2040
Effective area Aef [m2]
HxB 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000 1050 1100 1150 1200
240 0,03 0,04 0,04 0,05 0,06 0,06 0,07 0,08 0,09 0,09 0,10 0,11 0,11 0,12 0,13 0,14 0,14 0,15 0,16 0,16 0,17
440 0,06 0,08 0,09 0,11 0,12 0,14 0,15 0,17 0,18 0,20 0,21 0,23 0,24 0,26 0,27 0,29 0,30 0,32 0,33 0,35 0,36
640 0,09 0,12 0,14 0,16 0,19 0,21 0,23 0,25 0,28 0,30 0,32 0,35 0,37 0,39 0,42 0,44 0,46 0,49 0,51 0,53 0,56
840 0,12 0,16 0,19 0,22 0,25 0,28 0,31 0,34 0,37 0,40 0,44 0,47 0,50 0,53 0,56 0,59 0,62 0,65 0,69 0,72 0,75
1040 0,16 0,20 0,23 0,27 0,31 0,35 0,39 0,43 0,47 0,51 0,55 0,59 0,63 0,67 0,70 0,74 0,78 0,82 0,86 0,90 0,94
1240 0,19 0,24 0,28 0,33 0,38 0,42 0,47 0,52 0,57 0,61 0,66 0,71 0,75 0,80 0,85 0,90 0,94 0,99 1,04 1,08 1,13
1440 0,22 0,28 0,33 0,39 0,44 0,50 0,55 0,61 0,66 0,72 0,77 0,83 0,88 0,94 0,99 1,05 1,10 1,16 1,21 1,27 1,32
1640 0,25 0,32 0,38 0,44 0,51 0,57 0,63 0,69 0,76 0,82 0,88 0,95 1,01 1,07 1,14 1,20 1,26 1,33 1,39 1,45 1,52
1840 0,28 0,36 0,43 0,50 0,57 0,64 0,71 0,78 0,85 0,92 1,00 1,07 1,14 1,21 1,28 1,35 1,42 1,49 1,57 1,64 1,71
2040 0,32 0,40 0,47 0,55 0,63 0,71 0,79 0,87 0,95 1,03 1,11 1,19 1,27 1,35 1,42 1,50 1,58 1,66 1,74 1,82 1,90
BEN
BEE
BE
Dimensional range

8
FSD SMOKE CONTROL DAMPER
Range Supporting
construction
Wall
thickness
Supporting construction
details Type of installation Classification Pressure
difference Details Construction type
Sealing
type
200 x 240 - 1200 x 2040
Rigid wall
≥100mm Aerated concrete wall,
ρ≥ 500kg/m3
Dry instalation,
mineral wool 140 kg/m3,
intumescent fire resistant sealant
EI 90 (vew, i↔o) S1000
C10000 HOT 400/30 MA
multi
-1000 to 500 Pa
≥100mm Concrete wall,
ρ ≥ 500kg/m3 -1000 to 500 Pa
≥100mm Brick wall,
ρ≥ 500kg/m3 -1000 to 500 Pa
200 x 240 - 1200 x 2040
Flexible wall ≥100mm Plasterboard type F (EN520),
mineral wool up to 115 kg/m³
EI 90 (vew, i↔o) S1000
C10000 HOT 400/30
MA multi
-1000 to 500 Pa
Vertical duct Duct tested on EN1366-8 or
EN1366-9, ρ≥500kg/m3
Installation in duct-own design,
boards and glue
EI 120 (ved, hod, i↔o)
S1000 C10000 HOT
400/30 MA multi
-1000 to 500 Pa
Horizontal duct Duct tested on EN1366-8 or
EN1366-9, ρ≥500kg/m3
Installation in duct-own design,
boards and glue
EI 120 (ved, hod, i↔o)
S1000 C10000 HOT
400/30 MA multi
-1000 to 500 Pa
Horizontal duct installation
Aerated concrete ( ≥ 550 kg/m³), more
than 100 mm thick
Concrete wall (≥ 500 kg/m³) wall, more
than 100 mm thick
Plasterboard wall, type F (EN520),
mineral wool up to 115kg/m2,
more than 100 mm thick
INSTALLATION
Check for more information about certificate
installations in the declaration of performance:
www.klimaoprema.com/fsd/dop
Brick wall (≥ 500 kg/m³) wall, more
than 100 mm thick
Vertical duct installation
Connect the boards with Promat
Kleber K84 and screws
Sealing with mineral wool and
ablating coating
Construction of the duct
Smoke control dampers for multi compartments may be used with
ducts that have been tested to EN 1366-9 (Single compartment
smoke extraction ducts) and to EN 1366-8 (Smoke extraction ducts)
and that are constructed either from materials of the same density
(ρ≈ 500 kg/m³) as the tested material or from the same material
with a greater density or thickness. In addition, smoke extract ducts
that consist of sheet material from Promat, like Promatect L500,
Promatect AD 40 and Promatect LS, may be used.

PRODUCT OVERVIEW
DIMENSIONS
INSTALLATIONS
ACTUATORS
ACCESSORIES
MAINTENANCE AND OPERATION
9
FSD SMOKE CONTROL DAMPER
Wooden supports
min. 70mm
min. 40mm
INSTALLATION
The FSD Smoke control damper is always tested in
standardized support frames (both in a rigid wall and in a
flexible wall) in accordance with EN 1366-2: 2015. The results
obtained are valid for all similar support frames which have
a thickness and/ or density and/or fire resistance similar or
greater than the one on the test. Depending on where the
dampers are installed, country-specific regulations may apply
to ventilation applications.
The smoke control damper will never be, in practice, in the
open position at the beginning of the smoke hazard when
manually operated (MA). FSD smoke control dampers may
be installed in wall systems if these walls have been erected
in compliance with regulations and the manufacturer’s
instructions, and if the information on the respective
installation situation applies and the following requirements are
met.
When installed on a wall the dampers are suitable only for
installation in a vertical position, with the blade axis horizontal.
Dampers and duct must be suspended separately. The
ductwork must be suspended in such way that the transfer of
all loads from the adjoining ventilaton duct to the damper body
is completely exclude. Adjacent duct must be suspended or
supported as required by the duct suppliers. Smoke extraction
ducts can be connected to a smoke control damper as per
national authority regulations. Make sure that the smoke control
damper is not exposed to any external mechanical forces or
that the duct connetion is affecting the fuctional operation of
the damper. Connections should be performed according to
the instructions in this manual.
The gap in the installation opening between the smoke
control damper and the wall can be increased by up to 50%
of the gap area or decreased to the smallest amount that still
provides sufficient space for the seal.
Warning:
• Avoid damaging the casing
• Avoid casing deformation during installation and
commisioning
• Make sure that the product is installed in a way that is
accessible for future inspection and maintenance
• Avoid deformation of the casing during mounting and
sealing
• During installation, avoid applying force to the damper
blades.
Transport supports
(remove it after installation)
Reccomendation:
• Unload on a flat and dry surface
• Avoid shocks to the damper
• When using forklift for installation, make sure to support
the upper side of the smoke damper with wooden sup-
port beams

PRODUCT OVERVIEW
DIMENSIONS
INSTALLATIONS
ACTUATORS
ACCESSORIES
MAINTENANCE AND OPERATION
10
FSD SMOKE CONTROL DAMPER
Gap (G) Min. Max. Recomended
Mineral wool 50 150 100
G
GG
Installation gap
Center installation
• wall min. 100mm
Flush installation
• operation side
• wall min. 175mm
Flush installation
• installation side
• wall min. 175mm
max 75max 75 max 75 max 75
250
min 100
250
min 175
250
min 175

11
PRODUCT OVERVIEW
DIMENSIONS
INSTALLATIONS
ACTUATORS
ACCESSORIES
MAINTENANCE AND OPERATION
FSD SMOKE CONTROL DAMPER
Aerated concrete
wall installation
The wall is composed of aerated concrete
(minimum density of 500 kg/m³), and with minimum
thickness of 100 mm.
INSTALLATION
2
13
1. Create a hole in the wall. Check the recommended wall
opening on page 10. Cover the bottom side of the hole with
with Promastop CC (Hilti CFS-CT, Hensel HENSOMASTIK 5
KS Farbe). Thickness of the coating should be about 2 mm.
2. Insert the damper into the wall so that the bottom side
rests against the wall. CAUTION: Avoid leaning on the
damper blades during installation! Drill holes on the bottom
and top sides, and on the vertical side opposite the actua-
tor. Fix the smoke damper to the wall using masonry screws
(∅ 6, of appropriate length). CAUTION: Make sure that the
tightening force does not cause deformation of the housing!
Number of screws
∅ 6 top and bottom sides (B dimension)
200-500- 2 pcs.
550-850- 3 pcs.
900-1200- 4 pcs.
∅ 6 left sides (H dimension)
240-440- 1 pcs.
640-840-2 pcs.
1040-1240-3 pcs.
1440-1640- 4 pcs.
1840-2040- 5 pcs.
3. Fill the space between casing and wall with mineral wool (140 kg/m3) and seal all connections with
Promastop CC (intumescent fire resistant sealant). Mineral wool and the connection between the
damper and the mineral wool must be coated with one layer of fire protection coating.
Test the operation of the
damper blades!
Remove corner supports after
installation!
Make sure the head of the screws doesn’t
interfere with the operation of the blades!

12
PRODUCT OVERVIEW
DIMENSIONS
INSTALLATIONS
ACTUATORS
ACCESSORIES
MAINTENANCE AND OPERATION
FSD SMOKE CONTROL DAMPER
Rigid wall
installation
The wall is composed of concrete
(minimum density of 500 kg/m³) with a minimum
thickness of 100 mm.
2
INSTALLATION
13
Make sure the head of the screws doesn’t
interfere with the operation of the blades!
1. Create a hole in the wall. Check the recommended wall
opening on page 10. Cover the bottom side of the hole with
with Promastop CC (Hilti CFS-CT, Hensel HENSOMASTIK 5
KS Farbe). Thickness of the coating should be about 2 mm.
2. Insert the damper into the wall so that the bottom side
rests against the wall. CAUTION: Avoid leaning on the
damper blades during installation! Drill holes on the bottom
and top sides, and on the vertical side opposite the actua-
tor. Fix the smoke damper to the wall using masonry screws
(∅ 6, of appropriate length). CAUTION: Make sure that the
tightening force does not cause deformation of the housing!
Number of screws
∅ 6 top and bottom sides (B dimension)
200-500- 2 pcs.
550-850- 3 pcs.
900-1200- 4 pcs.
∅ 6 left sides (H dimension)
240-440- 1 pcs.
640-840-2 pcs.
1040-1240-3 pcs.
1440-1640- 4 pcs.
1840-2040- 5 pcs.
3. Fill the space between casing and wall with mineral wool (140 kg/m3) and seal all connections with
Promastop CC (intumescent fire resistant sealant). Mineral wool and the connection between the
damper and the mineral wool must be coated with one layer of fire protection coating.
Test the operation of the
damper blades!
Remove corner supports after
installation!

13
PRODUCT OVERVIEW
DIMENSIONS
INSTALLATIONS
ACTUATORS
ACCESSORIES
MAINTENANCE AND OPERATION
FSD SMOKE CONTROL DAMPER
Brick wall
installation
The wall is composed of brick blocks
(minimum density of 500 kg/m³) with a minimum
thickness of 100 mm.
2
13
Make sure the head of the screws doesn’t
interfere with the operation of the blades!
1. Create a hole in the wall. Check the recommended wall
opening on page 10. Cover the bottom side of the hole with
with Promastop CC (Hilti CFS-CT, Hensel HENSOMASTIK 5
KS Farbe). Thickness of the coating should be about 2 mm.
2. Insert the damper into the wall so that the bottom side
rests against the wall. CAUTION: Avoid leaning on the
damper blades during installation! Drill holes on the bottom
and top sides, and on the vertical side opposite the actua-
tor. Fix the smoke damper to the wall using masonry screws
(∅ 6, of appropriate length). CAUTION: Make sure that the
tightening force does not cause deformation of the housing!
Number of screws
∅ 6 top and bottom sides (B dimension)
200-500- 2 pcs.
550-850- 3 pcs.
900-1200- 4 pcs.
∅ 6 left sides (H dimension)
240-440- 1 pcs.
640-840-2 pcs.
1040-1240-3 pcs.
1440-1640- 4 pcs.
1840-2040- 5 pcs.
3. Fill the space between casing and wall with mineral wool (140 kg/m3) and seal all connections with
Promastop CC (intumescent fire resistant sealant). Mineral wool and the connection between the
damper and the mineral wool must be coated with one layer of fire protection coating.
Test the operation of the
damper blades!
Remove corner supports after
installation!

14
PRODUCT OVERVIEW
DIMENSIONS
INSTALLATIONS
ACTUATORS
ACCESSORIES
MAINTENANCE AND OPERATION
FSD SMOKE CONTROL DAMPER
Flexible wall
installation
The wall is composed of 2x2 plasterboard boards,
12,5 mm thick, installed on a steel frame construction.
To fulfill the classification it is NOT mandatory to use
the mineral wool inside the wall (mineral wool with
density up to 115 kg/m³can be used).The minimum
thickness of the wall is 100 mm.
INSTALLATION
B+580
H+180
(B+580)/3 (B+580)/3
23 4
1. Create a hole in the wall, check the recommended wall
opening on page 10. and build a subframe as per drawing 1.
2. Cover the bottom side of the hole with with Promastop CC
(Hilti CFS-CT, Hensel HENSOMASTIK 5 KS Farbe).
Thickness of the coating should be about 2 mm.
3. Insert the damper into the wall so that the bottom side
rests against the wall. CAUTION: Avoid leaning on the flap
slats during installation! Drill holes on the bottom and top
sides, and on the vertical side opposite the actuator. Fix the
smoke damper to the wall using masonry screws (Φ6, of
appropriate length). CAUTION: Make sure that the tightening
force does not cause deformation of the housing!
Number of screws
6x80 bottom sides (B dimension)
200-500 -2 pcs.
550-850 -3 pcs.
900-1200- 4 pcs.
6x180 top and left sides (H dimension)
240-440 -1 pcs.
640-840 -2 pcs.
1040-1240 -3 pcs.
1440-1640 -4 pcs.
1840-2040 -5 pcs.
4. Fill the space between casing and wall with mineral wool (140 kg/m3) and seal all connections with
Promastop CC (intumescent fire resistant sealant). Mineral wool and the connection between the damper
and the mineral wool must be coated with one layer of fire protection coating.
Test the operation of the damper blades!
Remove corner supports after installation!
1
Make sure the head of the screws doesn’t
interfere with the operation of the blades!
B+605
H+205
Detail of the opening in flexible wall

15
PRODUCT OVERVIEW
DIMENSIONS
INSTALLATIONS
ACTUATORS
ACCESSORIES
MAINTENANCE AND OPERATION
FSD SMOKE CONTROL DAMPER
D
D
D
D
D
D
Horizontal duct
installation
Smoke damper smaller
then duct
Duct is defined as a fire resistant smoke extract
duct, with wall thickness ≥ 35 mm. Duct is tested
according EN1366-8 or EN1366-9, with density
ρ ≥ 500kg/m3.
SECTION A-A
SECTION B-B
1. Create an installation opening according to drawing.
2. Fix the bottom fire rated boards to the duct first, to
create the underside for the smoke damper to sit on.
3. Place the smoke control damper in front of the
installation opening. If necessary, support the damper.
4. Fix the rest of the fire rated boards according to the
drawings.
Test the operation of the damper blades!
All connection must be covered with Promat Kleber
K84 or similar glue!
Duct and damper must be suspended separately.
Damper must not bear the weight of the duct and vice
versa.
A
A
A
A
A
A
Smoke extract duct
INSTALLATION

16
PRODUCT OVERVIEW
DIMENSIONS
INSTALLATIONS
ACTUATORS
ACCESSORIES
MAINTENANCE AND OPERATION
FSD SMOKE CONTROL DAMPER
A
A
A
A
Horizontal duct
installation
Smoke damper equal to
duct
Duct is defined as a fire resistant smoke extract
duct, with wall thickness ≥ 35 mm. Duct is tested
according EN1366-8 or EN1366-9, with density
ρ ≥ 500kg/m3.
Promatect H boards 10 mm
1. Create an installation opening aaccording to drawing.
2. Place the smoke control damper in front of the
installation opening. Support the damper.
3. Fix the rest of the fire rated boards according to the
drawings.
4. Cover top and bottom connections to the duct with
10mm Promatec H boards
Test the operation of the damper blades!
All connection must be covered with Promat Kleber
K84 or similar glue!
Duct and damper must be suspended separately.
Damper must not bear the weight of the duct and vice
versa.
A
A
A
A
A
A
Smoke extract duct
INSTALLATION
screw 5x70

17
PRODUCT OVERVIEW
DIMENSIONS
INSTALLATIONS
ACTUATORS
ACCESSORIES
MAINTENANCE AND OPERATION
FSD SMOKE CONTROL DAMPER
Horizontal duct
installation
Smoke damper in the
midle of the duct
Duct is defined as a fire resistant smoke extract
duct, with wall thickness ≥ 35 mm. Duct is tested
according EN1366-8 or EN1366-9, with density
ρ ≥ 500kg/m3.
A
A
SECTION A-A SECTION B-B
Promatect H boards 10 mm
1. Create an installation opening according to drawing.
2. Fix the bottom fire rated boards to the duct, to create
the underside for the smoke damper to sit on.
3. Place the smoke control damper in front of the
installation opening. Support the damper.
4. Fix the rest of the fire rated boards according to the
drawings.
Test the operation of the damper blades!
All connection must be covered with Promat Kleber
K84 or similar glue!
Duct and damper must be suspended separately.
Damper must not bear the weight of the duct and vice
versa.
Smoke extract duct
INSTALLATION

18
PRODUCT OVERVIEW
DIMENSIONS
INSTALLATIONS
ACTUATORS
ACCESSORIES
MAINTENANCE AND OPERATION
FSD SMOKE CONTROL DAMPER
Horizontal duct
installation
Smoke damper on the
end of the duct
Duct is defined as a fire resistant smoke extract
duct, with wall thickness ≥ 35 mm. Duct is tested
according EN1366-8 or EN1366-9, with density
ρ ≥ 500kg/m3.
A
ASECTION A-A SECTION B-B
Promatect H boards 10 mm
Smoke extract duct
1. Create an installation opening according to drawing.
2. Fix the bottom fire rated boards to the duct, to create
the underside for the smoke damper to sit on.
3. Place the smoke control damper in front of the
installation opening. Support the damper.
4. Fix the rest of the fire rated boards according to the
drawings.
Test the operation of the damper blades!
All connection must be covered with Promat Kleber
K84 or similar glue!
Duct and damper must be suspended separately.
Damper must not bear the weight of the duct and vice
versa.
BB
INSTALLATION

19
PRODUCT OVERVIEW
DIMENSIONS
INSTALLATIONS
ACTUATORS
ACCESSORIES
MAINTENANCE AND OPERATION
FSD SMOKE CONTROL DAMPER
A
A
BB
5x70 screw
SECTION A-A SECTION B-B
Horizontal duct
installation
Smoke damper smaller
then duct
Duct is defined as a fire resistant smoke extract
duct, with wall thickness ≥ 35 mm. Duct is tested
according EN1366-8 or EN1366-9, with density
ρ ≥ 500kg/m3.
Smoke extract duct
1. Create an installation opening according to drawing.
2. Place the smoke control damper on top of the
installation opening. Support the damper with additional L
profiles. Install suspension with drywall screws.
See page 26.
3. Fix the rest of the fire rated boards according to the
drawings.
Test the operation of the damper blades!
All connection must be covered with Promat Kleber
K84 or similar glue!
Duct and damper must be suspended separately.
Damper must not bear the weight of the duct and vice
versa.
A
A
BB
5x70 screw
SECTION A-A
SECTION B-B
A
A
BB
5x70 screw
SECTION A-A
SECTION B-B
INSTALLATION
screw 5x70

20
PRODUCT OVERVIEW
DIMENSIONS
INSTALLATIONS
ACTUATORS
ACCESSORIES
MAINTENANCE AND OPERATION
FSD SMOKE CONTROL DAMPER
Vertical duct
installation
Smoke damper smaller
then duct
Duct is defined as a fire resistant smoke extract
duct, with wall thickness ≥ 35 mm. Duct is tested
according EN1366-8 or EN1366-9, with density
ρ ≥ 500kg/m3.
Smoke extract duct
1. Create an installation opening according to drawing.
2. Fix the bottom fire rated boards to the duct first, to
create the underside for the smoke damper to sit on.
3. Place the smoke control damper in front of the
installation opening. Support the damper.
4. Fix the rest of the fire rated boards according to the
drawings.
Test the operation of the damper blades!
All connection must be covered with Promat Kleber
K84 or similar glue!
Duct and damper must be suspended separately.
Damper must not bear the weight of the duct and vice
versa.
SECTION A-A
SECTION B-B
B
B
A
A
B
INSTALLATION