KMC Controls STE-6012-10 User manual

STE-6012/6016 Room Temperature Transmitters 1 Installation Guide
Installation Guide
Room Temperature Transmitters (with LCD Display)
STE-6012/6016
Mounting 1
Location and Cover Removal 1
Handy Box Installation (Recommended) 1
Hollow Wall Installation 1
Wiring 2
STE-6016 2
STE-6012 2
Maintenance 2
More Information 2
Important Notices 2
Mounting
All dimensions are in inches
Handy Box Installation (Recommended)
1. Mountauniversal
backplateHMO-6036or
HMO-6036Wtothehandy
boxusingthetwoscrews
provided.
2. Removethecoverfrom
thebackpanel.
3. Aachthebackpanelto
thebackplateusingthe
twoscrewsprovided.
4. Aachthecabletotheterminalblockorjack
accordingtotheappropriatewiringdiagramon
thenextpage.
5. Replacethecover.
Hollow Wall Installation
1. Removethecoverfromthebackpanel.
2. Usingthebackpanelasatemplate,drilltwoholes
formountingscrews(7/64inchesor3mmindi-
ameterand1.4inches,1-13/32inches,or35.6mm
apart)andcutacenterhole(sizeneededisdepen-
dentonmodel)fortheterminalblockorjack.
3. Aachthebackpaneltothewallusingtwo
#6self-threadingscrews.(Plasticanchorsare
recommended,andthesizeoftheholeswillthen
needadjusting.)
4. Aachthecabletotheterminalblockorjack
accordingtotheappropriatewiringdiagramon
thenextpage.
5. Replacethecover.
Location and Cover Removal
Installthesensoronaninsidewallwhereitcansense
theaverageroomtemperatureandbeawayfrom
directsunlight,heatsources,windows,airvents,and
aircirculationobstructions(curtains,furniture,etc.).It
canbemountedonahollowwallor(withauniversal
backplateHMO-6036/HMO-6036W)toa2x4inch
handybox.
Thecoverisheldtotheblack,backpanelbythree,
small,roundpegsthattintheholesofthecover.
Theboompegisonatabandsnapsintothecenter
boomhole.
1. WithasmallPhillipsscrewdriverorhexwrench,
press in and hold the tab buon that snaps into
the center hole on the boom cover.
2. Carefullypullorprythebackpanelfromthe
frontcover.
2.438
2.250
R 3.094
R 0.187
0.643
STE-6012
0.475
max.
STE-6016
Modular
RJ-45
Jack
Four-pin
EIA-485
PC Data
Port
Clamp
(Screw-type)
Terminals
0.149
Model
Number
Connections
Screw Clamp
Terminals
RJ-45
Connector
EIA-485 Data
Port
STE-6012-10 X
STE-6016-10 X X

STE-6012/6016 Room Temperature Transmitters 2 Installation Guide
STE-6016
STE-6012
Wiring
ConnectingthismodeltoaKMCcontrollerrequires
aspecialcablewith(onthesensorend)anRJ-45
connectorand(onthecontrollerend)anRJ-11
connectorwithanadditionalthreewires(asrelevant
tothemodel)forcontrollerinputs.Purchasing
preassembledcablesfromKMCismorecost-
eectiveandreliablethancreatingcustomcablesin
theeld.Useoneofthefollowingcables:
• KMD-5693=25feet
• KMD-5694=50feet
• KMD-5695=75feet
Thethreeadditionalwireconnectionstothecontrol-
lerare:
• Orangeisthethermistor (temperature voltage)
signaltothecontroller’sappropriateinput
• Orange/whiteisthesetpointsignaltothecon-
troller’sappropriateinput
• Greenisthesupply voltageof7.5/12VDCfrom
anoutputofthecontrollerpress
KMD–5693 = 25 feet; KMD–5694 = 50 feet; KMD–5695 = 75 feet
1 8
Orange Wire = Thermistor Input to Controller
Orange/White Wire = Setpoint Signal Input to Controller
(for STE-6014/6016/6017/6018 only; clip or tape when not used)
12 inches
52
RJ-11 and
Wire Leads
to Controller
RJ-45
to STE
Sensor
Green Wire = Aux. Supply Voltage to STE-6015/6018
(10 VDC) or STE-6016 (7.5/12 VDC) (clip or tape when not used)
RJ-11 RJ-45 Color
(Lead) 8 Orange
7 N.C.
(Lead) 6 Green
3 5 Blue
4 4 Blue/White
5 3 Green/White
2 N.C.
(Lead) 1 Orange/White
(Cables crossed, 20 AWG)
Common (“Ground”)
0–5 VDC Temperature Signal and (during a Button Press)
SENSOR-ON (0 VDC on ) or SENSOR-OFF (> 5 VDC on )
D
B
C
A0–5 VDC Setpoint Signal
7.5 VDC (Setback/Setup) or
12 VDC (Normal) Supply (from Controller)
{
{
{
{
© 2012 KMC Controls, Inc. 866-019-05C
More Information
Forgeneralproductinfor-
mation,seetheSTE-6000
Series Room Temperature
Sensors/Transmiers Data
SheetontheKMCControls
website.
Formountingconsider-
ations,networkconnection,
controllerconguration,
programming,troubleshoot-
ing,andotherinformation,
seetheSTE-6012/6016
Application Guide.
Maintenance
Carefulinstallationwillalsoensurelong-term
reliabilityandperformance.Removedustasneces-
saryfromholesintopandboom.Cleanwithaso,
dampclothandmildsoap.
KMC Controls, Inc.
19476IndustrialDrive
NewParis,IN46553
574.831.5250
www.kmccontrols.com;[email protected]
Connectwiresasshownfortherelevantmodel.
Important Notices
Thematerialinthisdocumentisforinformation
purposesonly.The contents and the product it
describes are subject to change without notice.
KMCControls,Inc.makesnorepresentationsor
warrantieswithrespecttothisdocument.Innoevent
shallKMCControls,Inc.beliableforanydamages,
directorincidental,arisingoutoforrelatedtothe
useofthisdocument.
Up (Toward Ceiling at Installation)
NOTE: IntheSTE-6012/6016,pressingthe
Down buonmomentarilysends0 VDC
tothecontrollerforaSENSOR-ONsignal;
pressingtheUp buonsendsgreater
than 5 VDCforaSENSOR-OFFsignal.
Wheninnormal/overridemode,pressing
theDownorUpbuonraisesorlowersthe
setpointvoltage.Wheninsetback/setup
mode,pressingeitherbuonalsoselects
overridemode.