KNEX Rippin Rocket User manual

Keep this important information for future
reference. Read all warnings and instructions
before you start to build and operate the model.
WARNING: CHOKING HAZARD - Small parts.
Not for Children under 3 years.
CAUTION:
•Keep hair, fingers, face, and clothing away from all moving parts.
•Do not attempt to launch anything other than the Rippin’ Rocket car.
•Do not operate Turbo Boosters unless properly installed as shown.
•Do not obstruct Track with objects or any part of your body.
•You will need sharp scissors to cut the Track. Keep your hands and
fingers away from the blades and especially the points of the blades.
Adult help is recommended.
•Remove rechargeable batteries from model before charging; they must
be charged only under adult supervision.
•Non-rechargeable batteries must not be recharged.
•Do not mix different types of batteries; do not mix alkaline, standard
(carbon-zinc), or rechargeable (nickel-cadmium) batteries. Do not mix
new and used batteries. Only batteries of the same or equivalent type
recommended should be used.
•Insert batteries with correct polarity (+/-) as shown.
•Remove exhausted batteries from model; do not short-circuit supply
terminals.
•Keep Components free of dust; do not immerse or use in water.
•Alkaline batteries C (LR14) are recommended.
•Do not dispose of batteries in a fire; they could leak or explode and
cause injury.
•Remove all batteries if the toy will not be used for a long period of time.
•Power Option (not required): There is a plug on each Turbo Booster that
accepts a plug-in AC to DC power adapter, 4.5 Volt DC, 1000 (or
higher) mA, that can be used in place of the 3 batteries in each Turbo
Booster. This optional adapter can be purchased separately from most
electronics stores.
Be sure to use an adapter with the correct polarity.
Outside of jack is negative (-), inside of jack is positive (+).
Keep these instructions in a handy location.
They contain important safety information.
Here are a few tips before you get started.
•Take your time to enjoy the building process. Take breaks often and ask a
family member or friend to help. Most importantly, don’t rush!
•Install batteries before building models.
•Your roller coaster model will perform best when placed on a smooth, flat
surface.
•The RIPPIN’ ROCKET Roller Coaster sets up in 7 feet by 3 feet.
(213 cm x 91cm)
•If you need to move your model after it's built, two people can lift it
carefully, making sure you are not unsnapping the connections.
•Product and colors may vary.
Our Warranty (US and Canada)
K’NEX Industries warrants the RIPPIN’ ROCKET Set to be free of
manufacturing defects in material and workmanship for a period of
90 days from the date of purchase. If, within the period of warranty,
any part proves to have such defect, it will be replaced or repaired at
our option at no charge.
K’NEX will not be responsible for damage and/or abuse to your
RIPPIN’ ROCKET Set, and such will not be covered by this warranty.
Also, K’NEX will not be responsible for damage caused by defective or
old batteries. Old or damaged batteries can leak and corrode metals.
K’NEX’s sole and exclusive liability for defects in materials and
workmanship shall be limited to repair or replacement by our
Consumer Services Department, and K’NEX shall not be liable of
incidental, consequential, contingent damages, except in those states
that do not allow this exclusion or limitation.
This warranty gives you specific legal rights. You may have other
rights which vary from state to state.
+ -
IMPORTANT STUFF FOR PARENTS & KIDS
IMPORTANT STUFF FOR PARENTS & KIDS

• Car will go in the direction of the
arrow on top of the Turbo
Boosters.
•
Your set contains 6 Splice pieces for
connecting Track. If you cut the Track in
the wrong place, you can use the Splice
pieces to re-connect the Track.
•
TIP: DON’T THROW AWAY ANY EXTRA
TRACK. The best place to splice is on the
big, downward hill or the straight, flat
Track sections. Try to minimize the number
of splices.
• Pay special attention to the placement
of the Track Connectors and the
spacing between them.
•Use a small Phillips head
screwdriver to loosen the
screw, then remove each
battery door. Insert 3 fresh
“C” (or LR14) batteries into
each compartment with
the correct polarity.
•
Install all batteries in the
Turbo Boosters before
building.
With high-performance features that rival the most extreme
coasters in the world, your K’NEX RIPPIN’ ROCKET Roller Coaster
is built to thrill!
If your K’NEX Roller Coaster was life-sized and you were actually
riding it, it would perform something like this:
Coaster Performance (to scale):
Top Speed: Over 120 mph (193 km/hour)
Maximum Acceleration: 7 G’s
Height: 15 stories
Vertical Climb Angle: 90 Degrees
Vertical Drop: 12 stories
Super-G Loop Diameter: 3 stories
• Power Option (not required): There is a plug on
each Turbo Booster that
accepts a plug-in AC to DC
power adapter, 4.5 Volt DC,
1000 (or higher) mA, that can
be used in place of the 3
batteries in each Turbo
Booster. Adapter(s) can be
purchased separately from
most electronics stores.
You can use 1 or 2 adapters. If you are using
only 1 adapter, plug it into the Turbo Booster on
the floor. The batteries are easier to replace in
the Turbo Booster on the hill/side.
NOTE: When using a universal adapter with
multiple power settings, use ONLY the 4.5v
setting. Higher voltages WILL damage the
Boosters.
How to Insert and Remove Batteries:
GETTING STARTED
GETTING STARTED

Connectors
There are blue and purple Connectors with
special long slots. They slide together as
you see in the
pictures. Push
these parts
together until
you hear a
“click”.
Ready, Set, Build
To begin your model, find the
and follow the numbers. Each piece
has its own shape and color. Just
look at the pictures, find the pieces
in your set that match and then
connect them together. Try to face
your model in the same direction as
the instructions while you build.
Building with K’NEX
Hi! I’m your K’NEX Building Buddy.
If you are new to the K’NEX Rod
and Connector system, here are
some tips that will have you
building like a real K’NEXpert.
When you see me in
the instructions, you’ll
want to pay close
attention to the details
being pointed out.
1
Flexi-rods
A Flexi-rod is a Rod that you can bend to
make curves. It will be easier to attach to
your model if you bend it back and forth
first.
Movin’ On
Faded colors show you this section
is already built. You’ll want to connect
the new section to the place where
the arrows are pointing. The new
pieces you add and the place where
they connect will be in full color.
1 3
-
Spacers
There are places in your model where
you need to add silver Spacers.
Be sure to count them carefully.
2
4
3
5
6
1
2
3
4
1
K’NEX BUILDING BASICS
K’NEX BUILDING BASICS

Keep this important information for future reference.
•Remove rechargeable batteries from model before charging; they must be
charged only under adult supervision.
•Non-rechargeable batteries must not be recharged.
•Do not mix different types of batteries; do not mix alkaline, standard (carbon-
zinc), or rechargeable (nickel-cadmium) batteries. Do not mix new and used
batteries. Only batteries of the same or equivalent type recommended should
be used.
•Insert batteries with correct polarity (+/–) as shown.
•Remove exhausted batteries from model; do not short-circuit supply terminals.
•Requires 6 “C” (or LR14) batteries.
•Do not dispose of batteries in a fire; they could leak or explode and
cause injury.
•Remove all batteries if the toy will not be used for a long period
of time.
Track:
•It's important to adjust the Track, especially in the loop area, before
you finally cut the Track.
•If you cut the Track too short, you can use the Splice pieces to
re-connect it. Use a minimum of splices.
•Be sure to apply the Track so that it is very smooth. If the ends of
your Track are rough, trim a little off to make the ends a square,
clean cut.
Car Performance:
•For best operation, you may want to clean the sides of the car
periodically with a damp cloth.
•Car gets stuck at top.
A. If the Turbo Boosters are not running, check to see if the
batteries are fresh and installed properly.
B. Is Track built properly at top of frame?
•Car does not go through loop.
A. Check to see if loop is built correctly.
B. Is Track fully attached and smooth on the Track Connector?
C. Is return curve and frame built properly?
D. Do you have the right number of Track Connectors and are
they placed according to the instructions?
E. Are the support Connectors, that hold up the Track at specific
spots, on the proper side of the Flexi-rods?
To disassemble, you can use a
long green Rod to pop out the
orange Connector as shown.
TIPS & TROUBLESHOOTING
TIPS & TROUBLESHOOTING

The frame is built in
7 sections (A-G).
Le châssis est composé de
7 sections (A-G).
El armazón se construye
en 7 secciones (A-G).
Der Rahmen wird mit 7 Teile
zusammengebaut (A-G).
Het geraamte bestaat
uit 7 stukken (A-G).
NL
D
E
F
GBUS
RIPPIN’ ROCKET ROLLER COASTER
RIPPIN’ ROCKET ROLLER COASTER

1
2
3
1 3
-

4
1 4
-
1 3
-

5
5

7
6
5 7
-
5

x4
8
9
5 9
-
5 7
-
5 8
-

Connect the sections (Steps 1-4, Steps 5-9)
Connecte les sections (Etapes 1-4, Etapes 5-9)
Conecta las secciones (Pasos 1-4, Pasos 5-9)
Verbinde die Abschnitte (Schritt 1-4, Schritt 5-9)
Verbind de delen (Stappen 1-4, Stappen 5-9)
NL
D
E
F
GBUS
110
-
5 9
-
10
1 4
-

12
11
11 12
-

13
14
11 14
-
11 12
-
11 13
-

15
115
-
11 14
-
110
-
Connect the sections (Steps 1-10, Steps 11-14)
Connecte les sections (Etapes 1-10, Etapes 11-14)
Conecta las secciones (Pasos 1-10, Pasos 11-14)
Verbinde die Abschnitte (Schritt 1-10, Schritt 11-14)
Verbind de delen (Stappen 1-10, Stappen 11-14)
NL
D
E
F
GBUS

16
17
16 17
-

18
16 19
-
19
16 17
-

20
16 21
-
16 19
-
21

x2
16 22
-
16 21
-
22