KOBE PREMIUM IN2630SQB-700 Troubleshooting guide

KOBE Brand Range Hood
Model No.
IN2630SQB-700
IN-026 SERIES
INSTALLATION INSTRUCTIONS
AND OPERATION MANUAL

[ENGLISH]
- READ AND SAVE THESE INSTRUCTIONS -
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS ........................................................................1
COMPONENTS OF PACKAGE......................................................................................3
INSTALLATION...............................................................................................................4
OPERATING INSTRUCTIONS.......................................................................................9
SPECIFICATIONS ........................................................................................................13
MEASUREMENTS & DIAGRAMS.................................................................................14
PARTS LIST..................................................................................................................16
CIRCUIT DIAGRAM......................................................................................................18
TROUBLE SHOOTING.................................................................................................19
DISCLAIMER................................................................................................................20
WARRANTY..................................................................................................................21
PRODUCT REGISTRATION.........................................................................................23
- READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING -
ALL W I RING MUS T BE D O NE BY A PROFE SSIO NAL AN D IN
ACCO RDAN CE WI TH NAT IO NAL AND LO CAL E LEC TR I CAL CO DES

1
IMPORTANT SAFETY INSTRUCTIONS
- PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION -
WARNING : TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL
INJURY, OBSERVE THE FOLLOWING:
1) Installation and electrical wiring must be done by qualified professionals and in accordance
with all applicable codes and standards, including fire-rated construction.
2) When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or
other hidden utilities.
3) Ducted fans must be vented to the outside.
a) Before servicing or cleaning unit, open the light panel and SWITCH POWER OFF AT
SERVICE PANEL.
b) Clean all grease laden surfaces frequently. To reduce the risk of fire and to disperse air
properly, make sure to vent air outside. DO NOT vent exhaust air into wall spaces,
attics, crawl spaces or garages.
NOTE
- This warranty is void without an authorized agent’s receipt or if
unit is damaged due to misuse, poor installation, improper use,
mistreatment, negligence or any other circumstances beyond the
control of KOBE RANGE HOODS authorized agents. Any repair
carried out without the supervision of KOBE RANGE HOODS
authorized agents will automatically void the warranty.
- KOBE RANGE HOODS will not be held responsible for any
damages to personal property or real estate or any bodily injuries
whether caused directly or indirectly by the range hood.
WARNING : TO REDUCE THE RISK OF PERSONAL INJURY IN THE EVENT OF A
RANGE TOP GREASE FIRE:
1. Keep all fan, baffle/spacer/filter/oil tunnel/oil container and grease-laden surfaces clean.
Grease should not be allowed to accumulate on fan, baffle/spacer/filter/oil tunnel/oil
container.
2. Always turn hood ON when cooking.
3. Use high settings on cooking range ONLY when necessary.
4. Do not leave cooking range unattended when cooking.
5. Always use cookware and utensils appropriate for the type and amount of food prepared.
6. Use this unit only in the manner intended by the manufacturer.
7. Before servicing, switch power off at service panel and lock service panel (if possible) to
prevent power from switching on accidentally.
8. Clean ventilating fan frequently.

2
What to Do In The Event Of a Range Top Grease Fire
• SMOTHER FLAMES with a tight fitting lid, cookie sheet, or metal tray, and then turn off the
burner. KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If
the flames do not go out immediately, EVACUATE THE AREA AND CALL THE FIRE
DEPARTMENT or 911.
• NEVER PICK UP A BURNING PAN – You May Get Burned.
• DO NOT USE WATER, including wet dishcloths or towels – a steam blast will result.
• Use an extinguisher ONLY if:
a) You have a Class A, B, C extinguisher and know how to operate it.
b) The fire is small and contained in the area where it started.
c) The fire department has been called.
d) You can fight the fire with your back to an exit.
What to Do If You Smell Gas
- Extinguish any open flame.
- Do not try to turn on the lights or any type of appliance.
- Open all doors and windows to disperse the gas. If you still smell gas, call the Gas
Company and Fire Department right away.
CAUTION
1. For general ventilation use only. Do not use to exhaust hazardous or explosive materials
and vapors.
2. To reduce the risk of fire, use only metal ductwork. Sufficient air is needed for proper
combustion and exhausting of gases through the flue (chimney) to prevent back drafting.
3. Follow the heating equipment manufacturer’s guideline and safety standards such as those
published by the National Fire Protection Association (NFPA), and the American Society for
Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and code authorities.
4. Activating any switch on may cause ignition or an explosion.
5. Due to the size and weight of this hood, installation by 2 persons is recommended.
ELECTRICAL SHOCK HAZARD – Can result in serious injury or
death. Disconnect appliance from electric power before servicing.
If equipped, the fluorescent light bulb contains small amounts of
mercury, which must be recycled or disposed of according to
Local, State, and Federal Codes.

3
COMPONENTS OF PACKAGE
(Must keep all material for returns or refunds)
- FOR MORE INFORMATION, PLEASE VISIT OUR WEBSITE www.KOBERangeHoods.com OR
CONTACT KOBE RANGE HOODS AT [phone].
Range Hood Box
{A} KOBE Range Hood
{B} Warranty Registration Card
{C} Instruction Manual
{D} Baffle Filter – 2
{E} Oil Tunnel – 1
{F} Stainless Steel Spacer – 2
{G} Baffle Handle Package – 1
{H} Remote Control with holder – 1
{I} Round Vent Cover– 1
{J} Rectangular Exhaust plate – 1
{A}
{B} {C}
{D} {E}
{F} {G}
{H} {I}
{J}
Adjustable
Liner (Sold Separately)
{
K
} Front Section of Liner
{L} Rear Section of Liner
{K}
{L}
(AAA Battery not included.)

4
INSTALLATION
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING
Calculation before Installation
To calculate installation, please refer to TABLE 1. (All calculation in inches.)
- FOR UNDER THE CABINET -
TABLE 1
A = Height of Floor to Ceiling
B = Height of Floor to Counter Top
(Standard: 36")
C = Height of Counter Top to Wood Frame
Bottom (Minimum 27"to 30")
D = Height of Wood Frame
SAFETY WARNING
HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF
REMOVING ANY PARTS FOR INSTALLING, CLEANING OR SERVICING.
NOTE: BE CAREFUL WHEN USING ELECTRICAL SCREWDRIVER, DAMAGE TO THE HOOD
MAY OCCUR.

5
Preparation Before Installation
NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT
DEBRIS FROM ENTERING THE VENT OPENING.
• Decide the location of the venting pipe from the hood to
the outside. Refer to Figure 1.
• A straight, short vent run will allow the hood to perform
more efficiently.
• Try to avoid as many transitions, elbows, and long run as
possible. This may reduce the performance of the hood.
• Temporarily wire the hood to test for proper operation
before installing.
• Important: Peel protective film off the hood, if any.
• Use duct tape to seal joints between pipe sections.
CAUTION : If moving the cooking range is
necessary to install the hood, turn off the power in
an electric range at the main electrical box. SHUT
OFF THE GAS BEFORE MOVING A GAS RANGE
.
And use a protective covering to protect cooktop
and/or countertop from damage.
Custom Hood Preparation
1. The custom hood frame must be designed according to
the shape and the weight of the insert. Refer to
Measurements and Diagrams on Page 14-15.
2. A sturdy base (3/4 inch thick plywood recommended) is
needed to sustain the weight of insert.
3. If an optional liner will be installed, the side of the wood
frame must be sturdy (3/4 inch thick plywood
recommended).
4. It is recommended to install front & rear stud support
(not included). Refer to Figure 2. For safety purposes,
extra installation holes on the side of the insert are
provided. Prepare the side stud support if needed.
5. Determine and mark the centerlines on the base of the
wood frame where the insert will be installed.
6. Determine the proper location for the Power Supply
Cable. Make a wiring access hole using a drill bit.
Install the wire cable and seal the gap around hole.
7. Cut out the opening where the insert will be installed.
(Figure 3)
Liner Installation (Additional Purchase required)
8. The custom wood frame must have a sturdy base to
accommodate the cut-out for the insert. The base must
be recessed to accommodate the height of the liner (See
liner dimension on Page 15)
9. Secure the liner to the bottom of the base using screws
(not included) appropriate for the size and material of your
wood frame.
Figure 1
Figure 2
Figure 3
Figure 4

6
10. Liner is made up of two sections: a large, rear section with
pre-cut for insert and a front section for a total adjustable
depth between 23” and 25-3/4”.
11. Position the rear section of the liner so that it aligns with
the back edge of the custom wood frame. Use a pen to
trace the outline of the pre-cut area.
12. Install the rear section of the liner with 6 screws (not
included).
13. Install the front section of the liner with 3 screws (not
included)
Hood Preparation Before Installation
CAUTION : If moving the cooking range is
necessary to install the hood, turn off the power in
an electric range at the main electrical box. SHUT
OFF THE GAS BEFORE MOVING A GAS RANGE.
14. Choose the require vent option. The Round Exhaust
Plate is pre-installed for top vent.
15. For Top 3-1/4” x 10” rectangular installation only:
- Remove the Top Round Exhaust Plate. Refer to
Figure 5. Keep screws to attach Exhaust Plate.
- Attached the Rectangular Exhaust Plate using 10
screws. Refer to Figure 6.
16. For Rear Vent Options only:
NOTE: The blower is pre-installed for top vent. If
installing as rear vent, follow the steps below.
- Remove the 4 screws that secure the blower
system. Keep the screws. Refer to Figure 7. Slowly
rotate the blower system to align with the mounting
holes at the back of the insert. Secure the blower
system with 4 screws as shown in Figure 8.
17. For Rear 6” round installation only:
- Remove the Rear Round Vent Cover and Rear
Rectangular Vent Cover. Keep screws to attach
Exhaust Plate. Refer to Figure 4.
- Remove the Top Round Exhaust Plate. Refer to
Figure 5. Keep screws to attach the Round Vent
Cover and Rectangular Vent Cover.
- Attached the Round Exhaust Plate using 13 screws.
Refer to Figure 9.
18. For Rear 3-1/4” x 10” rectangular installation only:
- Remove the Rear Round Vent Cover and Rear
Rectangular Vent Cover. Keep screws to attach
Exhaust Plate. Refer to Figure 4.
- Remove the Top Round Exhaust Plate. Refer to
Figure 5. Keep screws to attach the Round Vent
Cover and Rectangular Vent Cover.
- Attached the Rectangular Exhaust Plate using 10
screws. Refer to Figure 10.
Figure 5
Figure 6
Figure 7
Figure 8

7
Duct Work Installation
19. Determine and make all necessary cuts in the wall or
ceiling for the ductwork. Note: Install the ductwork
before installing the insert.
20. Use steel pipe to connect the exhaust on the hood to the
ductwork above. Use duct tape to make all joints secure
and air tight.
21. Please refer to local codes for the usage of a damper
(not included).
Wiring to Power Supply
SAFETY WARNING
RISK OF ELECTRICAL SHOCK. THIS RANGE HOOD MUST
BE PROPERLY GROUNDED. MAKE SURE THIS IS DONE
BY QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL
APPLICABLE NATIONAL AND LOCAL ELECTRICAL
CODES. BEFORE CONNECTING WIRES, SWITCH POWER
OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO
PREVENT POWER FROM BEING SWITCHED ON
ACCIDENTALLY.
22. Connect electrical wires.
23. Connect three wires (black, white and green) to house
wires and cap with wire connectors. Connect wires
according to their colors (i.e. black to black, white to
white, and green to green).
24. Store wires in the wiring box.
Hood Installation
NOTE: USE HAND TOOLS ONLY. DO NOT OVER
TIGHTEN SCREWS. IT MIGHT CAUSED DAMAGED TO
THE HOOD.
25. Remove 10 screws located at the bottom of the insert.
(Figure 11). Carefully remove the light support panel.
26. Install the hood casing support (provided in the screw
package).
27. Position the insert inside the custom wood frame, and
secure the insert to the front and rear stud support.
(Figure 2) by using the front and rear mounting holes
(Screws not included).
28. For a more secure installation, use the mounting holes
located on the side of the insert
29. Make sure insert is secure before releasing.
30. Re-install the light support panel. (Do not over tighten
screws.)
CAUTION : MAKE SURE HOOD IS SECURE
BEFORE RELEASING.
Figure 9
Figure 10
Figure 11

8
Final Assembly
31. Install the oil tunnel into recess support near rear of
hood. Refer to Figure 12.
32. Install Baffle filters. Angle baffle filter toward back of
hood ①. Push baffle filter up until almost level ②.
Slide forward into recess behind the front of hood ③.
Lower baffle filter ④. Slide back until it fits into resting
position ⑤. Refer to Figure 13.
Figure 12
Figure 13

9
OPERATING INSTRUCTIONS
This KOBE hood is equipped with five electronic push buttons with LEDarray, six electronic button wireless
remote control, double horizontal squirrel cage blower with stainless steel baffle filter, and two bright LED
light.
The five control buttons are Power Control (On/Off), Speed Control (High, Medium, Low & QuietMode™),
ECO Control, Timer Control and Light Control. Refer to Figure 14.
Figure 14
Note: For best results, turn the range hood to QuietMode™ prior to any preparation or cooking. Adjust
speed as needed.
Power Control
Press Power Control to turn On/Off the range hood.
Output Display:
Speed Control
(Each press of speed button will cycle the fan through High, Medium, Low, and QuietMode™.)
Output Display will indicate:

10
= QuietMode™ Speed
= Low Speed
= Medium Speed
= High Speed
ECO Control
Press ECO Control to activate and deactivate the ECO Function. The ECO function is set to
turn on the range hood on QuietMode™ setting for 10 minutes every hour to remove excess
moisture, microscopic particles and odors to promote cleaner environment. The ECO
feature will be deactivated when the Speed Control is pressed and Speed Indicator is lit up.
NOTE: Must open door or windows to create sufficient make-up air when ECO is operating.
Output Display:
Light Control
(Lights are controlled independently from Power Control. Turning the power off will not turn the
lights off.)
Press Light control to turn lights ON and OFF.
Timer Control
Press Timer Control to start timer. The Timer Indicator on the display screen will flash.
Each press of Timer Control will increase by 1 minute on the display.
When Timer Control is activated, the range hood will automatically turn off after the set time.
Timer range from 1 min. to 99 mins.
To cancel the timer, press Timer Control twice.
Baffle Change Indicator
The display will indicate when baffle filter needs cleaning.
Press and hold the Power Control for 5 seconds to reset the Baffle Change Indicator.

11
Remote Control
The six control buttons for the wireless remote control are Power Control (On/Off), Light Control, Timer
Control, ECO Control andSpeedControls (High, Medium, Low& QuietMode™).
NOTE: Batteries are not included. AAA battery x 2 and re-install the batterydoor.
Power Control
Press Power Control to turn hood ON and OFF.
Light Control
(Lights are controlled independently from Power Control. Turning the power off will not turn the
lights off.)
Press Light control to turn lights ON and OFF.
Speed Control
Press the Speed Control to activate the fan. The fan will start on High speed. Each press of the
Speed Control button will cycle through the various speeds.
Press to cycle from High, Medium, Low, and QuietMode™.
Press to cycle from High, QuietMode™, Low, and Medium.
Timer Control
Press Timer Control to activate Timer. The Timer Indicator on the display screen will flash.
Press of will decrease the timer by 1 minute. Each press of will increase the timer by
1 minute.
If Speed/Timer Control button ( OR ) is not pressed within 6 seconds, the unit will
automatically exit the Timer mode, and the arrow will switch to speed function control.
When Timer Control is activated, the range hood will automatically turn off after the set time.
Timer range from 1 min. to 99 mins.
ECO Control
Press ECO Control to activate and deactivate the ECO Function.
For optimal performance, clean the range hood surface and baffles regularly.

12
To Clean Hood Surface
CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS.
*** Regular care will help preserve its fine appearance.
1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth.
2. If hood looks splotchy (stainless steel hood), use a stainless steel cleaner to clean the surface
of the hood. Avoid getting cleaning solution onto or into the control panel. Follow directions of
the stainless steel cleaner. Caution: Do not leave on too long as this may cause damage to
hood finish. Use soft towel to wipe off the cleaning solution, gently rub off any stubborn spots.
Use dry soft towel to dry the hood.
3. DO NOT allow deposits to accumulate or remain on the hood.
4. DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface
and cause rusting.
5. DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in
contact with stainless steel for extended periods. Many of these compounds contain chemicals,
which may be harmful. Rinse with water after exposure and wipe dry with a clean lint free cloth.
To Clean Baffle Filter/Oil Tunnel
CAUTION: DRAIN OIL FROM BAFFLE FILTER & OIL TUNNEL REGULARLY TO PREVENT
OVERFLOW.
1. Remove all the baffle filters and oil tunnel.
2. Using a sponge, wash with warm soapy water. Dry completely before returning into place.
(Note: Baffle Filters are top rack dishwasher safe.)

13
SPECIFICATIONS
MODEL / SIZE IN2630SQB-700 / 30”
COLOR Commercial Stainless Steel
CONSUMPTION / AMPERE 290W / 2.5A
VOLTAGE 120V 60Hz
NUMBER OF MOTORS 1
FAN TYPE: CENTRIFUGAL Double Horizontal Squirrel Cage
EXHAUST Top –
6” Round
3-1/4” x 10” Rectangular
Rear –
6” Round
3-1/4” x 10” Rectangular
CONTROLS 5 Push-Button with LED Array
- Variable Delay Shutoff
LIGHTS LED Lights 3W x 2
HOOD DIMENSION
(W X D X H) 30” x 18-1/2” x 12”
OPTIONALACCESSORIES
(W X D X H) 2 Piece Adjustable Liner Model No.: INL36252B
(34-7/16” x 23” to 25-3/4” x 3”)
HOOD WEIGHT (lbs) Net Gross
IN2630SQB-700 42 52
Blower Air Capacity (cfm) QuietMode™ Low Medium High
250 460 560 700
Sone* 1.0 3.5 5.0 6.0
dB 40.0 58.0 63.5 66.0
* One Sone is equivalent to 40 decibels.
**Specifications subject to change without notice.

14
MEASUREMENTS & DIAGRAMS
All ( ) are in millimeter.
All inch measurements are converted from millimeters. Inch measurements are estimated.
MODEL NO: IN2630SQB-700
Side View Bottom View
Back View Top View

15
Front View
Ajustable Stainless Steel Liner (Sold Separately)
Model No. INL36252B

16
PARTS LIST
MODEL NO: IN2630SQB-700
NO.
DESCRIPTION
MODEL/SIZE
PART NO.
1 Round Vent Cover B101-2630-17A
2 Rectangular Vent Cover B101-2630-17B
3 Round Exhaust Plate B101-2630-16A
4 Rectangular Exhaust Plate B101-2630-16B
5 Hood Casing IN2630SQB-700 IN2630
6 Transformer (LED Light) L1-0402-0120-700
7 Electric Component Support L1-0201-2630
8 Processor Board FA-18880-0401-B
9 Capacitor L1-0401-0120-01
10 Blower Bracket L1-0105-2630
11 Oil Tunnel IN2630SQB-700 B101-2630-14A
12 Blower System L1-0302-A120-01
13 Bottom Casing B101-2630-09
14 Baffle Filter Support B101-2630-14B
15 Stainless Steel Spacer B101-2630-14B
16 Baffle Filter B101-2630-15
17 Control Unit Support L1-0207-2630
18 Control Unit FA-18880-0401-A
19 Light Panel B101-2630-06
20 LED Light (3W) L1-0403-0001
Optional
Adjustable
Liner (Sold Separately)
21 Rear Seation of Liner INL36252B B103-2630-A
22 Front Section of Liner INL36252B B103-2630-B

17
Optional Liner (Sold Separately)

18
CIRCUIT DIAGRAM
MODEL NO.: IN2630SQB-700