KOCOM KIV-102 Instruction Manual

KIV-102, KIV-D102 Users Manual for Operation and Installation
Communication and monitoring b front door camera
Interactive call and communication between house and guardroom
Inner line call and communication within the house
Communication with lobb phone and door open function
Monitoring of lobb
For both single house and multi house (Apartments)
KIV-102 : AC t pe
KIV-D102 : DC t pe
B/W HANDS-FREE
VIDEO PHONE
Thank you very much
for purchasing KOCOM
video doorphone.
please read this manual
thoroughly to ensure
correct usage, before
operating
KIV-102, KIV-D102 05.08
This manual is based on the date as shown in the right and specifications
are subject to change without notice for qualit improvement.
PRODUCT
MODEL
DATE PURCHASED
WARRANTY PERIOD
AGENCY ADDRESS

KOCOM Warranties the original urchaser of this roduct
as follows.
1) This product is produced under strict qualit control and inspection procedures.
2) If this product breaks down during proper use as a result of product defect, KOCOM
will repair it within one ear from date of purchase free of charge.
3) The following cases will be subject to charge, even during warrant period:
a. Breakdown during transport, or through careless treatment, b consumer.
b. Breakdown cause b unauthorized repair, or s stem modification.
c. Breakdown caused b natural disaster or power disorder.
Warranty
Warrant Card
To receive after-Sale service, have the following ready
when you contact our branches
1. Name of the product
2. Model number of the product
3. The area of problem
4. Phone number and address at
which ou can be contacted.

Do not throw used-up batter into fire places, which ma cause fire and explosion.
Cautions for installation
The relevant law obliges users to have a qualified electrician carr out wiring work for power suppl . Work b disqualified
persons ma cause fire and electric shock.
Wiring work for communication cables needs techniques and experiences. For this t pe of wiring work, please consult to our
local sales agent.
According to the standard for electric work and other relevant regulations, install communication cables at the place awa
from power cables. The failure to install cables separatel ma cause fire, electric shock and communication troubles.
Do not install the product on rolling table or sloping place.
Dropping or falling ma cause damage on our product.
In installation, avoid the place exposed to tremor or shocks, which ma cause damages on our product.
Even if our product is waterproof, do not install it slanted place of water leakage, which ma cause a short circuit.
For the product of wall-mounting t pe with fixing pegs, keep it safel .
Fixing pegs ma cause injur of user.
Install the product of wall-mounting t pe carefull not to drop from the wall. Dropping due to earthquake or tremors ma
cause injur of user.
When installing the product on the wall, consider the thickness and material of the wall.
Dropping in use ma cause injur of user.
Cautions for Use
Do not put heav thing on the product. Dropping or falling due to heav things on it ma cause injur of user.
Cautions for Repairs and Maintenance
Clean the dust inside the product regularl . Failure to clean the dust for long time ma cause fire. For inspection and cleaning
of the inside of product, please contact our local sales agent.
When putting our hands into the inside of equipment, be sure that plug is alread detached form an outlet or circuit-breaker is
turned off.
Be careful not to expose the product to benzene, thinner or hot water.
Do not expose detergent directl to the product in a wa of spa ing, etc.
Moving equipment, be sure that the plug is detached from an outlet.
For equipment whose cables are connected to terminals, please contact our local sales agent or qualified electrician.
When replacing old fuse with new one, do not directl touch it with bare hands.
Use insulated tools or contact A/S center.
Cautions
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
Warnings for disposal
�Read this cautions carefull and keep it within eas reach of ou.
�For right installation, read this cautions thoroughl . Please install the product according to its specifications.
�This Cautions for Safet ma include items that are not contained in specifications of the product that consumer
purchases.
�Reading this cautions, use the product in a right manner. For further information, please contact our A/S center.
About S mbol
A variet of s mbols are used in this Cautions for Safet and our products to guide ou to use products in a right
and safe manner and to prevent possible risks for users and other persons and damages to their propert . The meaning
of each s mbol is as follows. After full aware of meaning of each s mbol, read the following cautions.
This s mbol means that wrong handling or ignorance of matters that this s mbol indicates
ma cause serious injur or even death of user.
This s mbol means that wrong handling or ignorance of matters that this s mbol indicates
ma cause serious injur or propert damage of user.
This s mbol means the matter that user should not do at na event.
This s mbol means that user should follow the instructions.
S mbols on Drawing
This s mbol means that contents (high voltage, electric shock, warnings, etc.) to which user
should pa attention are included.
This s mbols means that a certain action is not permitted. Specific points not permitted are
depicted around this s mbol (for example, in the left drawing, disassembl is not permitted.).
This s mbol means instructions or is used to force user to do a certain action. Specific
instructions are depicted on the drawing
(for example, the left drawing instructs user to detach power plug from an outlet).
Cautions for Safet
Warnings
Cautions
For safe use, please stick to the following cautions.
Warnings

�This product is onl for home. Do not the product for industrial or militar use.
�Do not handle the equipment with wet hand, which ma cause electric shock.
�Do not place wet or metallic materials on equipment. Water leakage or intrusion of metallic materials ma cause fire and
electric shock.
�Do not block the ventilating opening of equipment or put alien substances into it, which ma cause fire and electric shock.
�Do not use batter that is not designated or mix new batter with old ones. Insert batteries to fit their polarit . Explosion or
leakage of batter ma cause fire and injur of user.
�When visitor's image or voice is not displa ed on screen or not sounded from speaker, please check his/her identit before
opening the door and contact our A/S center.
�Do not use equipment when lighting is expected or strokes. It ma cause fire and electric shock.
�Do not open rear cover, cabinet and cover of equipment. It ma cause electric shock.
�Do not modif power cable or pull it with excessive strength, which ma cause fire and electric shock.
�Do not modif equipment. It ma cause fire and electric shock.
�Call signal ma cause damage on user's hearing abilit .
Cautions for Abnormalit
�When power cable is broken (exposure of core or short-circuit), do not fail to replace broken cable with new one. Failure to
replace broken power cable ma cause fire and electric shock.
�When detecting an abnormalities in equipment (communication is not available, images do not be displa ed on screen, calling
is not available, or abnormal sound is heard), immediatel detach plug from an outlet, or turn off circuit breaker or detach
batteries from equipment (in case that equipment has no plug) before requesting repairs to sales agent or A/S center. Keeping
connection to power suppl ma cause fire and electric shock.
�When alien substances go into equipment, immediatel detach plug from an outlet, or turn off circuit breaker or detach batteries
from equipment (in case that equipment has no plug) before requesting repair to sales agent or A/S center.
�In the case of smoke or smell of unknown origin from equipment, keeping use it ma cause fire and electric shock. Detach
plug from an outlet, or turn off circuit breaker or detach batteries from equipment (in case that equipment has no plug) and be
sure to check no more smoke or smell from equipment before requesting repair to sales agent or A/S center. Since personal
repairing work b user ma serious accidents. In an case, do not repair equipment with our own hand.
�When dropping equipment or breaking its cabinet, detach plug from an outlet, or turn off circuit breaker or detach batteries
from equipment (in case that equipment has no plug) before requesting repair to sales agent or A/S center. Keeping use
equipment ma cause fire and electric shock.
�Avoid direct exposure to sunlight and store equipment at the place free from dust and high temperature as ou can. High
temperature of equipment ma cause fire and electric shock.
Warnings Warnings
Cautions for Use
�Do not install the product at bathroom or at the place near a washing machine, or at other humid places. It ma cause fire or
electric shock.
�Do not install the product at the place near a dresser, humidifier or heater. Also avoid the place exposed to spark, heat or
humidit . All of them ma cause fire and electric shock.
�Do not install the product at the place exposed to dust, metals and harmful gas such as h drogen sulfide gas, all of which
ma cause fire and electric shock.
�Do not install the product at the place exposed to water and chemicals. This ma cause fire and electric shock.
�Do not scratch, break or arbitraril process power cable, which ma cause fire and electric shock. Putting a heav thing on a
cable, heating it or pulling it ma cause impairment on it.
�Do not place power cable at the place near heating equipment. It ma cause damage of cable's clothing material, which
result in fire ad electric shock. When detaching plug from an outlet, do not pull power cable.
�Damages on power cable ma cause fire and electric shock. When detaching plug from an outlet, please hold the plug
tightl .
�Do not detach plug from an outlet with wet hand. I ma cause electric shock.
�When using the existing wiring, be sure of the suitabilit of it to the product and install the product. Failure to this caution
ma cause fire.
�When moving equipment, be sure that plug is detached from an outlet and communication cable is disconnected. Damage
on cables ma cause fire.
�Voltage other than prescribed rated voltage is not permitted, which cause fire and electric shock.
�Do not use power terminal of product's main bod in other equipment than prescribed ones. It ma cause fire and short-
circuit.
�In wiring work, use the designated wiring materials.
Wiring work using other materials than designated ones ma cause fire.
�The equipment without waterproof marking shall not be installed at the place water leaks. It ma cause electric shock and
short circuit.
�When working, be sure that power is disconnected. Failure to disconnect power ma cause electric shock.
�Be sure that the power cable is connected and earths according to designated method. Failure to connection and earth ma
cause fire.
�Do not connect power to other terminals than designated ones.
�It ma cause fire and electric shock.
�When building a s stem with the product, do not connect the product other equipment than designated one. It ma cause
fire.
�When installing A/C switch, do work after removing the substance that ma cause short circuit or electric shock.
�Before installing or providing A/S service, be sure that the power is disconnected.
Cautions for Use

Home Auto: KHV-444/454/446/456
- Do not insert an metallic materials into the inside of fuse cover. It ma cause electric shock.
- Do not close ear to speaker. Abrupt call or signal ma give harmful effects on user's hearing.
- After turning power on and off, check again that input contents are saved correctl . Otherwise, data ma be missed when auto-signal mode operates.
- Use a standard detector. Non-standardized detectors are likel to cause fire due to excessive voltage or current.
- Please install motion detector at a place easil detect the motions of subjects. When detector is installed at a wrong place or obstacles block the front
side of detector, it cannot work well.
- When setting night guard mode, be sure that detector should be connected well.
- Sufficientl charge the batter of wireless handset before using it. Be careful that children should not throw batter . Be sure to close batter cover
(When children throw or disassemble batter , it ma cause serious accidents).
- Be careful that the polarit of the product matches to that of guardroom communication cable. When polarit is reversed, it ma cause abnormal
operations of the product or apartment s stem as a whole.
4-Line Related Products: KVM-604, 624, 524RG, 524G, 524GS, 520, KCV-346/356
- In wiring work, be careful that wirings should keep awa from the wall-mounting pegs or other furniture at regular interval. Contact of wiring with
wall-mounting pegs, etc. ma cause short-circuit, electric shock and fire (it is applied to all products with wall-mounting pegs).
- Use the prescribed standard wirings. Non-standardized wirings ma give adverse effects on operation of product
(it is applied to both video phone and CCTV).
CCTV Camera
- Do not install at nois places.
- Do not install at the place exposed to electromagnetic waves.
Excessive electromagnetic waves ma cause continuous noise on screen and mechanical troubles.
- When installing camera outdoor, please put it in the outdoor case. Otherwise, when it rains, the camera ma be broken or operate incorrectl .
- Install the product at well-ventilated places.
- Do not use the product for medical or militar uses.
- Do not install the product at humid places. It ma cause reduction of the product's durabilit as well as fire and electric shock.
- When lens is stained with alien substances, clean it with soft cloth to prevent the damages on it.
- Install the product out of reach of children.
S stem for Multi-unit Housing
- In installation, be careful that other wiring or metallic substances should not contact to the s stem for multi-unit housing.
- In installation, be careful that alien substances should not go into the s stem.
- Before installation, be full aware of wiring specifications of each model.
- In installation, be sure that the length and dimension of wiring meet the requirement prescribed in installation manual.
- Excessive strength and external shock ma cause mechanical breakdowns of equipment.
- Do not arbitraril open the case of the product
(When user opens the case arbitraril , KOCOM ma reject to provide A/S service).
Lobb Phone: KLP-(100, 104, 108, 112), KLP-(P100, P104, P108, P112), KDP-(100, 104, 108, 112),
KLP-(C100, C104, C108, C112)
- A stroke of lighting or strong shock ma give fatal and adverse effects on s stem. Thus, do not fail to ground the s stem.
- For registration of household password, please refer to user manual of the concerned product ( It is applied to ten-ke lobb phone products
[KLP-100, KLP-P100, KDP-100 and KLP-C100] ).
Rela : KVS-104P
- An rela can support up to four households.
- In the case of over four householders, additional rela s are needed.
Video Amplifier : KHU-102P
- In installation, follow the specification for image in/output.
Video Phone
- In assembling the product, be careful that wall-mounting pegs should not contact with wirings.
- In connection of cables, strip its insulation off as much as necessar (Excessive stripping off its insulation ma cause short circuit).
- Be careful that signal cables should not be wired with A/C wiring (it ma cause poor displa qualit ).
- Do not drop handset (its damage or short-circuit due to drop ma make communication impossible).
- When connecting wires to terminals, use standard screwdriver (otherwise, screws ma loosen, which will result in disconnection of wiring).
- Do not clean CRT screen with wet towel or cloth. When water penetrates into the product, it ma cause short-circuit.
Do not fail to clean it with dr towel or soft cloth.
- Do not install camera at the place where water penetrates or leaks. Penetration or leakage of water ma cause electric shock or short circuit.
Safet Instructions, Warnings, and Cautions of Each S stem
- This equipment is electronicall precision equipment, so do not arbitraril disassemble it.
- In installation of the product, do not fail to follow the specifications (specifications offered b KOCOM).
- Do not touch the product with alien materials (for example, sticker, magnet, opener, metal chopstick, etc.)
or insert them into the product (it ma cause reduction of the product's durabilit and harmful results to user as well).
- In the rain season, water is likel to penetrate into the product along the wiring. Thus, U-t pe finishing is recommended
as a desirable method of end part finishing.

Com onent’’ s Name
B
E
N
Z
E
N
E
T
H
I
N
N
E
R
CRT Screen 
Identif ing visitors
Precautions for O eration
Keep awa from humidifier and
stove. High temperature and
humidit can cause breakdown.
When cleaning, never use wet
hands, volatile benzene or paint
thinner.
Keep picture clear b cleaning
camera window frequentl with
soft cloths.
As this device consists of
electronic precision
components, and high voltage
is generated internall , do not
attempt to disassemble.
Do not drop monitor or door
camera, and avoid strong
impact.
Keep awa from devices
generating strong magnetic field
(TV, Speaker, etc.) (Picture can
be disturbed or blurred and
breakdown can result)
Installation Precautions
 Monitor and camera must be installed awa from direct
light and counter light.
 Camera must be installed at a place free from rain.
 Standard height of monitor must be 1,450mm~1,500mm
from ground, centered around brawn tube.
 Camera should be installed on the wall in which cement
is completel dr .
 If installed during winter season at temperature below
-5, condensation might be generated inside monitor and
camera due to temperature difference between indoors
and outdoors. To prevent breakdown due to such
condensation, connection should be made in 2 hours or
more after installation.
 Do not install monitor and camera in locations subject to
direct heating as harmful gases ma subsequentl be
emitted in significant amounts.
Stopping up pipe as above minimizes
temperature difference between indoors and outdoors, and
also eliminates moisture and condensation on door camera
window.
Stop up P.V.C. pipe using
adiabatic substances, to
prevent air circulation
 C-Mic
To communicate with Monitor
 Speaker
When visitor calls, the voice from monitor
comes out of the speaker.
 Call Button
B pressing the button, the related house
will be called.
 Camera Lens
Clear picture qualit realized
b adopting 1/3" CCD
MIC
Sending the voice to lobb phone, guard
phone, camera and other equipment
connecting to in-house line
Power LED
Communication Button
When receiving the call signal from interlocked
outside equipment, user can communicate with
it after pressing this button
Guardroom / Lobby Button
Chime Volume Switch 
Three-level (louder, middle and smaller)
adjusting the electronic tone sound
S eaker 
Door O en Button
Pressing this button while communicating,
user can automaticall open the front door
and common gate
Main Line Port from Lobb phone
A Port used when multi-home wiring is needed.
For further information, see the instruction sticker
or installation specifications
In-house Line Button 
Used in inner line call and communication
Power Cord: AC 220V - 230V
Front Door Button 
When receiving the call signal from front door,
user can communicate with front door after
pressing this button
Camera 1 Port
A Port connecting to in-house camera
Camera 2 Port
A Port connecting to in-house camera
Power Switch
KIV-102
Front Door Opener Port
A Port connecting to front door opener
Power Cord: DC 17V - 20V
DC INPUT (DC 17V - 20V)
House No. Setting Switch 
KIV-D102
KC-C63 Camera
 Power Lamp
To check power ON/OFF status

KC-C63 Surface-mounting Door Camera Installation
※Before installation, do not fail to shut the piping.
Standard Height of Door Camera
Standard height of the door camera is 1,400mm 1,450mm from the bottom of one camera
to the floor.
In case that the height of Door camera exceeds the range of min. 1,250mm1,550mm, it is
impossible to control the screen picture with onl the lens angle,
and therefore, be careful of the height of camera installation.
(unit:mm)
Door camera Installation
Bottom base of
One hall Box
Surface mount
Basic Installation method of Monitor
When s stem is attached to 1 rectangular switch box
Standard height monitor
Wall hanger panel for
fixing Monitor
Screw
Wall
Wall hanger panel
for fixing Monitor
1 Rectangular
switch box
Standard height of monitor is ranged 1,450 ~ 1,500
from bottom to the center of monitor screen.
For installation, avoid the places where there is an
excessive humidit ,magnetic force, dangerous
chemicals, direct ra of sun, and an places near a
heater which can cause break down.
Monitor Installation
(unit:mm)
Screw
Bottom of
1 Rectangular
switch box
Center of monitor
Straight Ahead Installation
Screw
Wall

Product S ecifications
AC 220V - AC 230V / DC17V - DC20V (Stand-b : Min 4.1W, Operation: Max 24W)
DC +12.8V
Call Signal (Electronic Tone Sound)
User can monitor situations of front door camera using "Front Door" button on monitor.
B pressing "Guard/Lobb " button for about 5 seconds, users can monitor lobb situations
(This function is available onl in lobb phones adopting TEN-KEY [KLP-100 series] mode).
When pressing call button on outdoor camera, call signal rings.
Explanation for melod t pe of front door camera :
- Camera 1 : ‘Ding-Dong~’ 2times
- Camera 2 : ‘Ddiriri~’ 8times
Hands-free S stem (DSP)
In calling from front door camera, image maintains for about 30 seconds.
While communicating, image maintains for about 3 minutes.
Front Door Camera: 4-wire Polarit IV 0.65mm or more
Main line: VOICE1/VOICE2/DATA(3-line) Polarit IV 0.8mm or more
Power (+/GND) (2-line) Polarit IV 1.2mm or more
For Video line, coaxial cable is used - COAXIAL 5C-2V
191(W) X 217(H) X 52(D) mm
Front Door Camera: When 0.65mm cable is used, 30m
Main Line Communication Line: When IV 0.8Фis used, 300m
Monitor: 0.C ~ 50.C
Power Source
Voltage of O erating Power
Lobby / Guardroom / In-house Call Signal
Monitoring of Front Door Camera
Lobby Phone's Lobby
Monitoring Function
Call Method
Communication Method
Image Maintenance Time
Number of Wiring
Dimensions
Communication Distance
Guaranteed O eration Tem erature

KC-C63 Front Door Camera

KIV-102 Monitor / KIV-D102 Monitor
Com onent
Monitor Accessories
Camera
Monitor Components
①A Wall Hanger Frame
②Wall Hanger
Fixing Screws
③Wiring Lines of Camera 1 & 2
Blue (Power)
Yellow (GND)
Red (Voice)
White (Video)
Gra (+17V)
Violet (GND)
Blue (Voice)
Green (Voice)
Yellow (Video)
Orange (Data)
Red (In-house Line)
Brown (Data in-house line)
Black (Video Output)
④Wiring Lines of Multi-home Main Wiring
Front Door Camera Components
①Camera Main Frame Supporter
Monitor
②Screws for fixing camera
to main frame supporter
③Screws for fixing cabinet
bod on the wall
④Upward adjusting Supporter
for lens angle
Power Source
Ambient tem erature
Angle of icture
Min. Illumination
Lens
Dimension
DC12V ±1V(Power suppl for monitor)
-10~ 50
Diagonal 120。
0.1Lux(LED ON)
F:2.0, f=3.0mm
95(W) X 127(H) X 34(D)mm
CAMERA (KC-C63)

Wiring Diagram Wiring Diagram
Precautions for Wiring
As incorrect wiring ma cause the devices non-operation
or poor communication qualit , please carefull
conduct wiring work.
When connecting a wiring chord to a terminal, loosen
screw, insert the end of the chord into the bottom part of
screw, and tighten the screw.
When fixing wiring chord, use stapler not to cause damage
to the chord.
When using existing wiring, please be cautious not to
cause disconnection and short-circuit.
 Wiring for multi houses (apartment) using KLP-100 series Lobb phone
- Video phone to Video phone wiring in a house.
 Wiring for single house without lobb phone connection
Cautions
1. Pin No.6 (data line) in Main Line Port is not connected in sub video phone.
2. Pin No.1, 2, 3, 4, 5, 7 & 8 in Main Line Port are used in a form of parallel connection between
main monitor and sub monitor.
3. The DIP switch in sub unit should be set as “0”.
Cautions
1. Pin No.1, 2, 7 & 8 in Main Line Port should be connected between main and sub monitor for internal
call and communication.
2. For the connection with KIP-603, please refer to the wiring diagram in multi houses (apartment) in next.
3. In extention with KIP-603 (Audio phone), it is not available to make conversation with front door camera.
4. The DIP switch in sub unit should be set as “0”.
Cautions
- Door lock connection
Onl one door lock should be installed and
connected to the monitor for front door open.
(single house use)
If 2 door locks are installed in parallel connection,
these 2 doors will be open at same time.
- Front door camera connection
Be careful in camera connection to the camera
ports. As the camera ports have different
2 call sounds,
if camera 1 is connected to the camera port 1
in main monitor and to the camera port 2
in sub monitor, main monitor and sub monitor
have different 2 call sounds. And camera 1 has 2
different call back tones, too.
- Call sounds : Camera 1 - ‘Ding~Dong~’ 2 times.
Camera 2 - ‘Ddiriri~’ 8 times.
Cautions
- Door lock connection
Onl one door lock should be installed and connected to the monitor for front door open. (single house use)
If 2 door locks are installed in parallel connection, these 2 doors will be open at same time.
- Front door camera connection
Be careful in camera connection to the camera ports. As the camera ports have different 2 call sounds,
if camera 1 is connected to the camera port 1 in main monitor and to the camera port 2 in sub monitor,
main monitor and sub monitor have different 2 call sounds. And camera 1 has 2 different call back tones, too.
- Call sounds : Camera 1 - ‘Ding~Dong~’ 2 times. Camera 2 - ‘Ddiriri~’ 8 times.

 Wiring for multi houses (apartment) using KLP-100 series Lobb phone
- Video phone to Audio phone wiring in a house.
Cautions
1. Terminal No. 5(data line) in sub audio phone is not connected from Pin No. 6(data line) of main
monitor.
2. Pin No. 1, 2, 3, 4, 7 & 8 in Main Line Port (Monitor) are used in a form of parallel connection
between main monitor and sub audio phone (1, 2, 3, 4, 6, 7).
3. In extention with KIP-603 (Audio phone), it is not available to make conversation with the front
door camera.
4. The DIP switch in sub unit should be set as “0”.
Communication between front door camera and interphone is unavailable.
Instructions for O eration
 Functional Descriptions

Communication with front door when a visitor comes:
When a visitor presses the call button of front door camera,
1. Call signal rings at home monitor and its screen is automaticall turned on to displa a visitor.
2. If pressing communication button or front door button on the front side of videophone,
user can communicate with the visitor at front door.
(The monitor screen will be automaticall faded out after 30 seconds)
3. If pressing communication button or front door button again after communication with
the visitor, user can end the communication (and screen is also faded out). If user wants to keep
communicating, press front door button again to connect to front door camera and then press
communication button .
B doing so, monitor screen is turned on and user can keep communicating with the visitor. (While
communicating with the visitor, if user presses the door open button , house front door
will be opened.)

Monitoring of Front Door Situations
1. Monitoring for Camera 1
- If pressing the front door button once on the monitor, the image from camera 1 port is displa ed
on the monitor screen.
2. Monitoring for Camera 2
- If pressing the front door button once on the monitor, the image from camera 1 port is displa ed
on the monitor screen. And if pressing the front door button once again, the image from
camera 2 port is displa ed on the monitor screen. Then, if pressing the front door button once
again, the monitor screen is turned off.
3. In case onl one camera is installed
- If pressing the front door button , the image is displa ed on the monitor screen.
If pressing once again, there will be no image displa ed on the monitor screen.
- In case camera 1 is connected to the camera port 2 at the back of the monitor.
If pressing the front door button once, there is no image displa ed and then if pressing once
again, the image from camera port 2 is displa ed. In this case, if ou change the camera 2 port to
1 port, it will work in normal.
4. In case two cameras are installed.
- If pressing the front door button once, the image from camera 1 is displa ed and if pressing
once again, the image from camera 2 is displa ed. If pressing one more, the monitor
screen is turned off.
- Cautions : Be careful for wrong connection between cameras and camera ports.

Call from Guardroom - How to communicate
1. If the guard calls to the house, tone sound rings and both communication and guard/lobb LED flicker
at the front side of videophone.
2. When user presses communication or guard/lobb button , communication begins.
3. When user presses communication or guard/lobb button again, communication is ended.


Call to guardroom - How to communicate
1. When user presses guard/lobb button , call signal rings and the button's LED is turned on
to call guardroom phone.
2. If handset is picked up in guardroom phone, communication begins (for up to 3 minutes).
3. If hanging up the handset in guardroom or pressing communication or guard/lobb button
on videophone, and communication will be automaticall ended.

Call from lobby hone - How to communicate
1. When a call from lobb phone, both communication and guard/lobb buttons flicker
(tone sound rings for 30 seconds).
2. Press communication or guard/lobb buttons , and communication will be
available (communication lasts for 3 minutes).
3. Press door open button on videophone while communicating with lobb phone to operate
common gate opener.
4. Press either communication or guard/lobb button to end communication.

Monitoring of Lobby (Common Gate) Situations
1. If pressing the guard/ lobb button around 3 sec. on the monitor for about 3sec, the image
from lobb phone (common gate camera) is displa ed on the monitor screen.
But in case the lobb phone (common gate camera) or guardroom phone is bus , the image from
lobb phone (common gate camera) is not displa ed.
2. After 8 sec. of lobb (common gate) monitoring, the monitor screen is automaticall turned off.
3. In house, the users can see the image and hear the voice from the lobb phone (common gate camera)
for 8 sec.
4. This lobb (common gate) monitoring function is onl available with 10 ke t pe of KLP-100,
KLP-P100 & KLP-C100 lobb phone (common gate camera).
Communication is available only when o tions are installed. If o tions are not installed,
only tone sounds rings.
Call from In-house Line (When o tions are installed)
1. When internal call signal, in-house line LED at the front side of videophone flickers.
2. Press either communication or in-house line button to start communication
(LED keeps On-mode).
3. Communication is available for up to 3 minutes. When 3 minutes pass, communication is automaticall
ended.
4. Press either communication or in-house line to end communication.
Internal Call using In-house Line (When o tions are installed)
1. When user presses in-house line button , the button's LED flicker and a call signal is sent to
extended unit.
2. Press communication or in-house line button on extended unit to begin
communication (communication maintains for 3 minutes).
3. Press communication or in-house line button to end communication.
Users can control chime volume b adjusting 3-level volume switch on videophone.
In all functions, call maintenance time is set for 30 seconds. After 30 seconds, call signal and images
return to stand-b mode.
All communications maintains for 3 minutes. After 3 minutes, communication automaticall
returns to stand-b mode.
 Instructions for Operation
Model: (KLP-100 / KLP-P100 / KLP-C100), Functional S ecifications

Call to house
When a visitor calls to house using lobb phone, press house number.
> Pressing call button, call sound rings and house is called.
> If the house responds to the call, communication is available for 3 minutes.
(Pressing door open button during the communication, opener installed with common gate is opened.)
> When communication is ended, device returns to standb mode.

Call from lobby hone to guardroom
Pressing 0and call button on the lobb phone, guardroom is called and lobb phone ID is displa ed
in guardroom phone.
> Communication with guardroom maintains (for 3 minutes). When communication is ended,
device returns to standb mode.

Password Change
(Password change function is onl available during the call with house.)
Pressing # # 0 0 #during the call with house, - - - - is displa ed.
Input new password and press button.
e.g) When register passward as ‘1111’. (It should be 4 digits)

Door o en using lobby hone with assword
Pressing house number + # + password + #designated b the house, door is automaticall opened.
when the user from house number “0101” opens common gate with passward.
e.g) Press house number 0101, #, passward and # in order.
[Lobby Phone's Direct-Button Call Function]
Model : KLP-104, 108, 112, KLP-P104, P108, P112, KLP-C104, C108, C112
To call to house, ress house number using lobby hone's key ad.
Tone sound rings and call signal is sent to the house.
Pressing the call button again while calling, calling is cancelled. No separate cancel button is offered.
If called house is communicating with extended other lobb phones or guardroom phone,
bus signal sounds and device immediatel returns to stand-b mode.
▷▷O eration of Door O ener While Communicating with House
1. Pressing door open button during the communication with house, common gate is opened.
(Door Opener Specification: Within DC 12V 300mA)
※Functional specifications ma be changed according to the specifications of installed products.
(Stand-b ) (House Number) (Call state) (Communication state) (Stand-b )
(Stand-b ) (Guard Master Number) (Call state) (Communication state) (Stand-b )
(Communication state) (Password input mode) (Hold) (Password) (# Button)
(Stand-b ) (House Number) (# Button) (Password) (# Button) (Releasing common gate)

Numbers b the figure indicate the number set when
all switches move toward ON direction.
1. Above figure, turning all DIP switches from No.1 to No. 12 toward ON direction, numbers set b DIP
switches are summed up.
e.g. 1) Above figure, turning switch No.1 and No. 2 toward On direction, value is set at 3 (1 + 2 = 3) since
numbers set b switches are 1 and 2.
e.g. 2) Above figure, turning switch No.1 and No. 3 toward On direction, value is set at 5 (1 + 4 = 5) since
numbers set b switches are 1 and 4.
e.g. 3)
e.g. 4)
e.g. 1)
e.g. 2)
DIP Switch Setting at House Inter hone and Video Phone

3. If DIP switches are set as in the above example, press 8102to call the house using guardroom master
or lobb phone.
In addition, house number is displa ed as small character b102in FND of guardroom master or
lobb phone.
4. Precautions for DIP Switch Setting (House No. Setting)
1) After setting DIP switches, device power should be reset.
(In power switch ON state, DIP switches cannot be set.)
2) For setting basement floors, switch No. 11 and 12 should be ON state.
3) For direct button t pe lobb phone, up to 12 houses can be set.
Thus, when DIP switches of house interphone and video phone are set, available houses are also 1 to 12
in number.
For Common gate pannel (KDP-104/KDP-108/KDP-112) and Lobb Phone (KLP-104/KLP-108/KLP-112,
KLP-C104/KLP-C108/KLP-C112, KLP-P104/KLP-P108/KLP-P112), house (KVM-520 and KIP-603,
KIV-102, KIV-D102, KIV-202, KIV-D202) No. setting should be conducted as following instructions.
(A specification preset b internal protocol)
House No. (DIP Switch) Setting for direct button t pe.
(Warning!) House device should be set as described above (Fix house No. t pe).
4) If user wants to use interphone or video phone as sub-phone, all DIP switches should be in OFF state.
5) When user sets DIP switches, excessive impact on DIP switches ma cause abnormal or erroneous
operation of device.
2. For basement floors, DIP switch No. 11 and 12 are generall set toward ON direction.
In this case, the value of DIP switch setting is 3,000 (1,000 + 2,000). However, program uses 8with
similar shape of B(Basement) to indicate basement floors. Thus, value is not 3,000 but 8,000.

11
9
7
5
3
1
A
12
10
8
6
4
2
B
�
�
House Setting No.