Kodak LUMA 150 User manual

Quick Start Guide

CONTENTS
EN
INTRODUCTION
PRODUCT OVERVIEW
CHARGING THE PROJECTOR
POWERING THE PROJECTOR ON/OFF
SCREEN MIRRORING
WIRELESS SETTINGS AND SOFTWARE UPGRADES
ADJUSTING FOCUS
ADJUSTING VOLUME
VIEWING DISTANCE AND SCREEN SIZE
USING THE PROJECTOR
CUSTOMER SERVICE CONTACT INFORMATION
FR
PRESENTATION
VUE D'ENSEMBLE
CHARGER LE PROJECTEUR
MISE EN MARCHE/ARRtT DU PROJECTEUR
DIFFUSER L'ECRAN
ARAMETRES SANS FIL ET MISES A NIVEAU DU LOGICIEL
REGLAGE DE LA MISE AU POINT
REGLAGE DU VOLUME
5
5-6
7
7
7-9
9-10
10
10-11
11
11-12
12
13
13-14
15
15
15-17
17-18
18-19
19

INTRODUCTION
Thank you for purchasing the KODAK LUMA 150 Portable Projector.This User
Guide is intended to provi de you with guidelines to ensure that operation of
th is pr o duct is safe and does not po se risk to the user. Any use that does not
c onform to the guidelines described in this User Guide may void the limited
warranty.
Th is product is covered by a limited one-year warranty. Coverage is subject to
limits and exclusions.See warranty for details.
Please make sure to view and down load the full user guide at
www .kodakphotoplus.com
PRODUCT OVERVIEW
1. Lens 1. Power
2. Speakers 2. Focus Wheel
3. Return 3. Air Inlet
4. Confirm / Play / Pau se 4. Tripod Dock
5. Ri ght / FF / Volume + 5.
Rat i ng Label
6. Left / REW / Vo l ume -
6. Non-slip Mat
7. Volume Switch 7. MicroSD Slot
8. Power Indicator 8. Speaker
9. Audio Output (3 . 5mm)
5I EN

10. USB Input/ Power Out
11. HDMI Input
12 . DC Input (5V/2.4A)
13. Reset
[t5J
0000000
000000000
000000000
0000000
.
-J -
~
:!) --- - -
•
•
•
•
EN l6
'1 1 1) ► I - -
•
0000 00 -
0 --
D
[Il) □ oo mm
•
.

CHARGING THE PROJECTOR
Before using the projector, connect it to the charger, plug the USB end of the
charging cable in to a wall charger or similar power source and allow it to fully
charge. This process should take about three hours.
Always use the original charger that was provided to ensure proper charging,
and make sure the power rating of the adapter for the charging cable is~2.4A
POWERINGTHE PROJECTOR ON/OFF
To turn the projector on or off, simply hold the power button on the side for
three (3) seconds. Once powered on, the projector's main menu will display the
remaining battery percentage.
SCREEN MIRRORING
Th is projector allows you to share the screen from your compatible iOS,
Android™, or Windows® 10device. Follow these steps to activate the screen
sharing function:
1. Open the third menu option, "Wireless." The name
of the device and the password to connect to it will appear at the
top of the screen. It will be PRO-XXXXXX (where all the X's are
integers between 0-9) and the password will be 12345678.
7I EN

ENl8
2. Activate your device's screen mirroring software and
let it scan for devices.
a. To activate screen mirroring on your Android™ device:
i. On Samsung devices, swipe down from
the top notification bar to the expanded
view, and then swipe left(if necessary) and
touch the "SmartView" icon to activate
screen sharing. NOTE: Check your device
settings for the screen casting/screen
mirroring options. The name of the
function may vary by device model and
service carrier. Other names used may
include, "Cast," or "Screen Mirroring," as
well as "Smart View". All devices must be
running at least Android version 4.1.2 .
b. To activate screen mirroring on your iOS device:
i. Swipe up to reveal the Control Center and
tap the "AirPlay Mirroring" button.
c. To activate screen mirroring on your Windows® 10
device:
i. From the start menu, select "Settings."
ii. In the Settings menu, select "Devices."
iii. On the leftside of the Devices menu,
select "Connected Devices," and then click
"Add a Device."

3. Select the projectorfrom the li st of compatible devices.
4. If the system prompts you to enter a password, enter "12345678 ."
5. When connected, the screen from your devicewill be mirrored to
the projector, so you can then use your device to play videos,
share images, etc.
6. Disconnect your device when finished.
WIRELESS SETTINGS AND SOFTWARE UPGRADES
To adjust the wireless settings on th is projector, you' ll need to connect to the
projector's hotspotwhile it is in wirel ess mode and proceed from there. Follow
these instructions to connect to the hotspot:
1. Turn on the projector and select the third menu option, "Wireless".
The name of the device and the password to connect to it will
appear at the top of the screen. It will be PRO -XXXXXX (where
all the X's are integers between 0-9) and the password will be
12345678. NOTE: You can change the wireless hotspotpassword
from the wireless settings menu that can be accessed by
following thesesteps.
2. Open yourdevice's wirele ss s ett ing s, and you should see a secure
wireless network with the PRO -XXXXXX name. Sel ect that
network and enter the default password (12345678).
9IEN

3. Open your device's internet browser and enter the following URL
to adjust the settings: 192.168.49.1
4. The browser should display two options, to adjust the wireless
access points, or to adjust the settings. Software upgrades can
be found and installed from the Settings menu. You can also
adjust the projector's hotspot password and other advanced
options from this menu.
ADJUSTING FOCUS
If the image on the screen appears fuzzy or unfocused when you turn the
projector on, use the focus wheel on the side to correct the image. Turn the
wheel up or down until the image appears sharp and clear.
NOTE: Ifa specific image or video remains fuzzy after adjusting the focus
wheel, try hitting the back button to return to the main menu. If the main menu
graphics appear clear and the image is still fuzzy, the problem may be the
image or videoquality.
ADJUSTING VOLUME
During playback, if you need to adjust the volume, touch the .- ibutton, and
the screen will display the volume bar.
EN I10

Once the volume bar appears on screen, use the < and > buttons to adjust the
volume accordingly.
VIEWING DISTANCE AND SCREEN SIZE
See the chart below to see how far away to place your projector from the
display area to create the intended screen size.
])
USING THE PROJECTOR
0.56m 1.07m 1.60m 2.13m 2.65m 3.20m
1. Turn the projector on and connect either a USB drive, micro SD card,
or an HDMl-compatible device via the ports on the side of the projector.
NOTE: if you connect an HDMI device as well as a micro SD card or USB
drive, the HDMI device will take precedence and you will need to disconnect
it to access the otherconnected sources.
2. Optionally, connect a speaker or headphones to the AUDIO OUT jack.
11 I EN

3. Use th e touch menu on the top of the projector to navigate to either
"Images" or "Videos" from the main projector menu. The projector will access
the files on your connected device and populate both sections.
4. If you want to use the screen mirroring option, navigate to "Wireless"
from the main menu and follow the instructions on page 3 to connect your
device.
5. Turn the focus wheel to make sure the image is crisp and clear as you
view your videos, images, or mirrored screen.
6. Enjoy!
CUSTOMER SERVICE CONTACT INFORMATION
Should you experience any problems with your product, please
contact us before returning the item to the place of purchase. We're here to
help!
U.S. Support: [email protected]
844-516-1539
International Support: [email protected]
844-516-1540
EN I 12