Kodak 2400 DV Plus User manual
IMAGELINK2400DVPlus
andAccessories
InstallationGuide
Unpacking
and
Setting up
Unpacking and Setting Up
1. Remove the plastic bag from the machine and remove all accessories in
the packing material.
Operator's Manual (1).
3 x 8 mm screws for RFC Option I/F Board (5)
Power Cord (1)
Printer Cable (1)
Prism Unit (1)
2. Remove the foam packing and several pieces of tape holding the machine
housing into position.
3. Remove the 2 screws from the front of the machine. Retain the screws as
they will be needed later in this procedure.
4. Remove 2 screws from the top OPTICAL COVER, slide to the rear and
then lift the cover off the machine.
5. Remove the foam from the MIRROR of the OPTICAL COVER.
6. Remove the several pieces of foam packing and tape from the inside of
the machine, refer to the illustration.
NOTE
Check and remove any material from the SCAN DRIVE SHAFT.
7. Install the PRISM into the PRISM HOLDER and then install the SHIELD
PLATE removed in the previous step of this procedure.
NOTE
Be sure to install the SHIELD PLATE even if the PRISM is not to be used.
8. Replace the OPTICAL COVER.
9. Connect the Printer to the Reader, follow this procedure
.
10. Connect the Personal Computer to the Reader, follow this procedure
.
11. Connect power to the machine and check operation.
Connecting
the
MSP3500
Printer.
PR Mode (Scanner + Printer)
1. Connect the Printer Cable to either of the ports at the rear of the MSP 3500.
NOTE:
The MSP 3500 Printer will support two DV Plus Scanners connected to it like. If
you intend to use this type of configuration, it is possible for the Printer to print
an identifier on each print so the operators can distinguish between which
scanner the prints came from.
This is enabled in the DV Plus Function Mode, “S7”. See the User’s Manual of
the scanner for more details.
2. Connect the Printer Cable to the scanner.
3. Power on the Printer and the scanner.
4. After the Printer has initialized enter the Function mode on the scanner.
* Select Fb → START key is turned ON, it will display as follows.
For MSP3500 : Fb → Pr → 35 → Fb
For MSP3000 : Fb → Pr → 30 → Fb
6. Test the machine operation.
Connecting
To a
Personal
Computer.
PC Mode (Scanner + Personal Computer).
The Scanner is connected to a personal computer and the scanned images
can be uploaded to the computer. An optional PC interface kit required for
connection to a personal computer. The SCSI cable should meet the following
specifications:
1. Power down the Reader and the Personal computer.
2. Connect the USB cable to the PC’s USB 2.0 port.
3. Connect the other end of the cable to Personal Computer.
5. Check Reader operation.
6. The
printer can be switched using Control Panel.
Manual
Frame
Masking
Kit
Manual Frame Masking Kit
Check all the component parts are in the kit before starting the installation.
1. Check the Reader is working correctly before starting the installation.
2. Power down the Reader and remove the power cord.
3. Remove the 2 screws from the top OPTICAL COVER, slide the cover to
the rear of the machine lift and remove.
CAUTION
Be careful not to damage the mirror mounted on the underside of the cover.
4. Remove the left side cover and the metal plate behind the cover.
NOTE
The METAL COVER only installed on 220vac machines.
5. Remove the PROJECTION UNIT.
6. Remove the lower left side cover.
7. Remove the STOPPER from the right hand side cover and open the
RIGHT COVER. Remove the metal plate behind the RIGHT COVER.
NOTE
The METAL COVER only installed on 220vac machines.
8. Remove the PLATE under the CCD ASSEMBLY.
9. Remove the FRONT & REAR SHIELD PLATES.
10. Lift up and remove the SCREEN FRAME ASSEMBLY, disconnect the
connector from the CONTROL PANEL PCB.
11. Peel off the LABELS from the SCREEN FRAME.
12. Fix the new X and Y DIRECTION LABELS from the MANUAL MASKING
KIT onto the SCREEN FRAME.
13. Remove the PLATE SPRING from the
rear side of the SCREEN FRAME.
14. Insert the X key A and the X key B (see
component contents listing of the Manual
Masking Kit) supplied into the backside of
the SCREEN FRAME shown in the
illustration.
15. Connect the connectors of the HARNESS A supplied in the kit into the new
X-DIRECTION PCB supplied.
16. Install the X-DIRECTION PCB onto the backside of the SCREEN FRAME
assembly.
17. Install the PLATE A supplied in the kit onto the SCREEN FRAME shown in
the illustration.
NOTE
The Ground of the CONTROL PANEL BOARD must
not touch the Auto Image Rotation (AIR)
potentiometer.
18. Insert the Y key A and Y key B (see component contents listing of the
Manual Masking Kit) supplied into the backside of
the SCREEN FRAME shown in the illustration.
19. Insert the PLATE B supplied in the kit onto
the SCREEN FRAME as shown in the
illustration.
20. Install the Y-DIRECTION PCB.
21. Connect the connectors of the HARNESS A onto the Y-DIRECTION PCB.
22. Install the 5 PLATE C supplied onto the SCREEN FRAME.
23. Install the WIRE SADDLES, one large and one
small from the kit on to PLATE C as shown in the
illustration of the left.
24. Secure the wiring into the wire saddles.
25. Secure the WIRE HARNESS in the wire saddles.
26. Insert the HARNESS A inside the SCREEN FRAME. Attach a “cushion”
(bumper) from the kit under the RESISTOR ARRAY to fix the harness.
27. Connect the connectors of the HARNESSES A and B as shown in the
illustration.
28. Install the large WIRE SADDLE in the frame of the Reader and the EDGE
COVER as illustrated.
29. Re-install the Reader SCREEN FRAME and connect the connector to the
CONTROL PANEL PCB.
30. Insert the HARNESS of the SCREEN FRAME through the hole of the
EDGE COVER, and secure the WIRING HARNESS in the wiring saddles.
31. Connect the black connector of the MANUAL MASKING HARNESS to the
remaining connector on the left hand side of the machine.
Secure the HARNESS
into the Wire Saddles as
shown in the illustration.
32. Continue to clip the Wire Harness into the wire saddles down the left side
of the machine as illustrated.
33. Connect the MANUAL MASKING HARNESS connector into PJ7 on the
PWB-BB PCB.
34. Re-install all the PLATES and COVERS on the Reader.
35. Apply power and check the Reader for correct operation.
Foot Switch
Accessory.
Other manuals for 2400 DV Plus
2
Table of contents
Other Kodak Scanner manuals
Kodak
Kodak Scanmate i1120 User instructions
Kodak
Kodak I1860 - Document Scanner Technical manual
Kodak
Kodak I780 - Document Scanner User manual
Kodak
Kodak Point-of-Care CR 120 System Installation instructions
Kodak
Kodak i1400 Series User manual
Kodak
Kodak i1300 Plus Series User manual
Kodak
Kodak I780 - Document Scanner User manual
Kodak
Kodak P460 User manual
Kodak
Kodak i4250 User manual
Kodak
Kodak 5500 - EASYSHARE All-in-One Color Inkjet User manual
Kodak
Kodak Ngenuity 9090DB User manual
Kodak
Kodak i1800 Series Operating instructions
Kodak
Kodak I1420 - Document Scanner User manual
Kodak
Kodak I250 - Document Scanner User manual
Kodak
Kodak Scanmate i920 User manual
Kodak
Kodak SCANZA User manual
Kodak
Kodak i1200 series User manual
Kodak
Kodak SCAN STATION 100 User manual
Kodak
Kodak i2900 User manual
Kodak
Kodak I810 - Scanner Firmware - PC User manual
Popular Scanner manuals by other brands
LZR
LZR FLATSCAN SL user guide
Hart InterCivic
Hart InterCivic Verity Print Troubleshooting Field Guide
GRAPHTEC
GRAPHTEC CS610-11eN Service manual
Canon
Canon DR 7090C - imageFORMULA - Document Scanner user manual
Revopoint 3D Technologies
Revopoint 3D Technologies POP 2 user manual
QPIX
QPIX PS970H Quick user guide