Kodak i100 Series User manual

for Kodak Scanners
Cleaning and Consumable Replacement Instructions
IManualnstruction
Versitec is a division of Cranel, Inc.
i100/i200/i260

INSTRUCTION MANUAL FOR
KODAK
i100/i200/i260 Scanner
Versitec 1- 888 - 722 - 6548 www. versitec.com

Step One: Cleaning the scanner......................................2
Step Two: Cleaning the separator module....................3 - 4
Step Three: Cleaning the feed module........................4 - 5
Step Four: Cleaning drive rollers & transport area.......6 - 7
Step Five: Cleaning the imaging guides...........................7
Step Six: Cleaning the paper path...................................8
TABLE OF CONTENTS
I. i200 Scanner Maintenance
II. i200 Replacing Parts
Step One: Replacing the feed Module & feed....................9
For inquiries during any of these procedures,
contact the Versitec Customer Support Center
at 1-800-224-3475.
Versitec 1- 888 - 722 - 6548 www. versitec.com 1
Step Two: Cleaning the paper path................................10
Step Three: Replacing parts..................................10 - 11

Cleaning the scanner
2Versitec 1- 888 - 722 - 6548 www. versitec.com
The scanner will collect dust and other debris during routine scanning.
Foroptimalscannerperformance,followthedetailedcleaninginstructions
in this section and clean the feed module rollers, separator module rollers,
imaging guides, transport area, and paper path at least once per week.
Clean the scanner and paper path daily if you are scanning carbonless
paper or newsprint, or if you are using the imprinter.
Use only these cleaning materials:
IMPORTANT
Staticide Wipes contain isopropanol which can cause eye
irritation and dry skin. Wash your hands with soap and
waterafterperformingmaintenanceprocedures.Referto
theMaterialData Safety Sheet (MSDS) for more information.
The MSDS is available on the Kodak web site at
www.kodak.com/go/MSDS.
Allow all rollers to dry completely before using the scanner.
NOTE:
Theuse of any other cleaning materials could damage your scanner.
Usefreshcleaningmaterialunlessotherwiseindicated.Inaddition
to the recommended cleaning supplies, you may use a vacuum
cleanertoremovedebrisfromthe scanner. Some debris from the
rubbertireson the feed module and separator module is normal.
Tire debris does not always mean that the tires are worn or damaged.
Aftercleaning, inspect the tires for wear and replace the separator
moduleorfeedmoduleifnecessary.Toordercleaningsupplies,refer
to Appendix B, Supplies and Accessories.
I. ii
ii
i260260
260260
260 MaintenanceMaintenance
MaintenanceMaintenance
Maintenance
Item CAT No.
Kodak Digital Science Roller Cleaning Pads (24) 853-5981
Staticide Wipes for KODAK Scanners [phone]
Kodak Digital Science Transport Cleaning Sheets (50) 169-0783

Cleaning the separator module
5Remove the separator module by pulling it down and lifting it off.
Separator
module
1 Powerdown the scanner.
2 Removeanydocumentsfromthefeederarea.
3 Lift up the scanner door release to unlatch the scanner door.
4 Pull up to open the scanner door.
Versitec 1- 888 - 722 - 6548 www. versitec.com 3

Front Roller
Cover
Cleaning the Feed Module
1 Push against the raised edge on the left side of the front roller cover to
the side and pull the cover up and out to remove it.
4 Versitec 1- 888 - 722 - 6548 www. versitec.com
6 Manually rotate and wipe the separator module rollers with a roller
cleaning pad.
7 Inspect the rollers. If the separator roller tires show signs of
wear or damage, replace the tires or the separator module.
8 Insert the separator module and align the shaft ends.
9 Press until the separator module clicks into place.
10 Go to the next section to clean the feed module.

4 Inspect the feed module. If the feed module tires show signs of
wear or damage, replace the tires or the feed module.
5 Remove any dust or debris from the tray area under the feed
module and the front roller cover.
6 Insert the feed module by aligning the pins and pushing it toward
the right to fit it into position.
7 Re-installthefrontrollercover.
8 Go to the next section to clean the drive rollers and transport area.
Versitec 1- 888 - 722 - 6548 www. versitec.com 5
Feed module
3 Manually rotate and wipe the feed module rollers with a roller
cleaning pad.
2 Remove the feed module by pushing it to the right and lifting it out.

Cleaning the Drive Rollers and
TransportationArea
6 Versitec 1- 888 - 722 - 6548 www. versitec.com
1 Manually rotate and wipe the drive rollers with a roller cleaning pad.
2 Clean any dust or debris in the slots around the drive rollers.
3 Wipe the upper and lower transport areas with a roller cleaning pad.
4 Dry the transport area with a dry Staticide Wipe.
5 Push against the raised edge on the left side of the rear roller cover
and pull the cover up and out to remove it.

Rear roller
cover
6 Removeanydust or debris under the rear roller cover.
7 Re-installtherearrollercover.
8 Go to the next section to clean the imaging guides.
Cleaning the Imaging Guides
Clean the exposed (top side) surfaces of the imaging guides.
You do not need to remove theimagingguides for cleaning.
1 Wipe the upper and lower imaging guides with a Staticide Wipe.
2 Dry the imaging guides with a dry Staticide Wipe.
3 Lower the scanner door and press it down firmly until it latches
into place.
4 Go to the next section to clean the paper path.
Versitec 1- 888 - 722 - 6548 www. versitec.com 7