Kodak P811 User manual

P811 Personal Photo
Scanner
User Guide
Guide de l’utilisateur
Guía del usuario

2 Customer Support: http://www.pandigital.net/kodaksupport
Table of Contents
Read This First ..................................................................................................................................... 5
Important Safety Precautions ........................................................................................................... 5
Introduction .......................................................................................................................................... 6
Scanner Overview................................................................................................................................ 6
Scanner Indicator Lights..................................................................................................................... 7
Suitable and Unsuitable Original Types ............................................................................................ 8
Supported Memory Cards ................................................................................................................... 9
Plastic Sheaths..................................................................................................................................... 9
Orientation of the Original and Scanned Picture............................................................................ 10
Operating the Scanner....................................................................................................................... 10
Preparation and Initial Setup .......................................................................................................... 10
Setting the Scanning Resolution .................................................................................................... 11
Scanning a Photo ........................................................................................................................... 11
Scanning 35mm Negatives............................................................................................................. 11
Feeding Filmstrips .......................................................................................................................... 12
Automatic Image Cropping ............................................................................................................. 13
Connect Scanner to a PC .................................................................................................................. 14
PC System Requirements .............................................................................................................. 14
For WINDOWS VISTA Users ......................................................................................................... 15
For WINDOWS XP Users............................................................................................................... 15
For WINDOWS 7 Users.................................................................................................................. 15
For MAC Users............................................................................................................................... 15
Scanned Picture Naming Convention............................................................................................. 16
Safely Disconnect the Scanner from Computer ............................................................................. 16
Scan PC Software for KODAK Personal Photo Scanners.............................................................. 16
Install Scan PC Software................................................................................................................ 16
Using the Scan PC Software.......................................................................................................... 17
Uninstall the Scan PC Software ..................................................................................................... 17
Scan Mac Manager (Macintosh) ....................................................................................................... 17
System Requirements .................................................................................................................... 17
Installing the Scan Mac Manager ................................................................................................... 17
Using the Scan Mac Manager ........................................................................................................ 18
File Naming Convention ............................................................................................................ 18
Manually Start the Scan Mac Manager .......................................................................................... 18
Uninstalling the Scan Mac Manager............................................................................................... 18
KODAK EASYSHARE Software for PC ............................................................................................ 18
System Requirements .................................................................................................................... 18
Install EASYSHARE Software ........................................................................................................ 18
Launch EASYSHARE..................................................................................................................... 19
Uninstall the EASYSHARE Software.............................................................................................. 19
KODAK EASYSHARE Software for MACINTOSH............................................................................ 20
System Requirements .................................................................................................................... 20
Install EASYSHARE Software ........................................................................................................ 20
Uninstall the EASYSHARE Software.............................................................................................. 20
Scanner Maintenance ........................................................................................................................ 20
Calibrate the Scanner ........................................................................................................................ 21

Customer Support: http://www.pandigital.net/kodaksupport 3
Notes on Battery Usage..................................................................................................................... 21
Storing the Scanner ........................................................................................................................... 21
Technical Specifications ................................................................................................................... 21
Frequently Asked Questions ............................................................................................................ 22
Upgrading Software and Firmware .................................................................................................. 23
Disposal of this product.................................................................................................................... 23
Limited Warranty................................................................................................................................ 23
FCC Statement............................................................................................................................... 24

4 Customer Support: http://www.pandigital.net/kodaksupport
04.Kodak P811_UG_v1.6_EN-FRC-SP_2010-09-07

Customer Support: http://www.pandigital.net/kodaksupport 5
Read This First
Please read the following important safety instructions carefully before using the KODAK Personal Photo Scanner. Failure to
observe these instructions may result in personal injuries or damages to the scanner.
Important Safety Precautions
Always follow these basic safety precautions when using your scanner. This reduces the risk of fire, electric shock, and
injury.
Do not place this device under direct sunlight or near heat sources, such as in a closed car under sunlight
or near a stove. The outer casing of this device may become deformed and the sophisticated sensors
inside may become damaged due to excessive heat.
Do not use this device near water, in the rain or allow any liquid to get inside this product. Water and
moisture may cause short-circuit to the electronic components and lead to malfunctions.
Do not use this device in dusty environments. Dust grains may cover this device and scratch the original.
Do not scan originals that are contaminated by dusts or other particles.
Do not use this device near strong electromagnetic sources, such as a microwave oven or television. The
electromagnetic interference may cause this device to malfunction.
Do not attempt to disassemble or modify this device. There are no user serviceable parts inside this
scanner, and unauthorized modifications voids your warranty.
Do not drop or apply shock/vibration to this device. Strong impacts may damage the components inside.
Do not insert objects other than compatible memory cards into the memory card slots of this scanner. The
metal contacts inside the slots can easily become damaged by foreign objects.
Do not use an unknown power adapter other than the one supplied with this scanner. Connecting this
scanner to an unknown power adapter is very dangerous and may lead to fire or explosion.
Some adapter models may include switchable prongs. When necessary to use alternate prongs, use only
the prongs included with the scanner.
Do not cut, bend, modify, place heavy objects, or step on the cable of the power adapter. Otherwise the
external insulation may be damaged and result in short-circuit or fire.
The power socket and USB port on this scanner are designed solely for connecting to the supplied power
adapter and optional USB cable. Do not insert any other objects into these sockets.
If there are strange odors or heat emitting from this device or any signs of malfunction, disconnect this
scanner from the power immediately and contact your dealer for inspection or service.
What’s in the Box
Check the package for the following items. If there are any items missing or damaged, please contact your place of
purchase immediately.
Personal Photo Scanner
AC Power Adapter (varies by region)
USB Cable
SD Memory Card
35mm Negative Adapter
Calibration Card
Plastic Sheath
Scan PC Software (on SD Card)
KODAK EASYSHARE Software (on SD Card)
Quick Start Guide
User Guide

6 Customer Support: http://www.pandigital.net/kodaksupport
Introduction
Now you can scan your printed photos and negative films and store them on your memory card. No computer is necessary. Simply
insert a memory card into the scanner, and power it on. When the unit is ready, feed your printed photo or negative film into the
scanner and your pictures are stored on the memory card. It’s as easy as that.
If you want to transfer your photos directly into your PC, it’s just as easy via a USB cable and our Scan PC Software (page 16).
Scanner Overview
Front View
No. Name Function/ Description
 Power Button
Press once to turn on in 600dpi mode; press again for 300dpi mode.
Press and hold for 1 second to turn off.
If an original jams in the feeding slot , press to back it out from the scanner.
 Power Indicator Indicates the power status of the scanner. (Refer to “Indicator Lights” on page 7.)
 Status/Card Indicator Indicates the operating status of the scanner and memory card. (Refer to “Indicator Lights”
on page 7.)
 Paper Guide Slide Slide the guide to adjust for smaller originals to ensure the proper alignment.
 Feed Slot Insert non-transparent originals like photos and business cards.
 Adapter Grooves For installing the 35mm Negative adapter.
 Mini USB socket For connecting to a computer via a USB cable.
 Power socket For connecting to the supplied power adapter.

Customer Support: http://www.pandigital.net/kodaksupport 7
Rear View
No. Name Function/ Description
 Output slot The scanned original exits from this slot.
 SD/xD/MMC/
MS Card slot
Accepts the following types of memory cards: SD, xD, MMC and MS. Also accepts
MICROSD Cards with an SD adapter. (Refer to "Supported Memory Cards" on page 9.)
Bottom View
Scanner Indicator Lights
Listed below are the indicator light patterns and the functions they represent:
Blinking slowly
Blinking rapidly
Steadily on
 Off
Power Status
/Card




(orange)

(green)
The scanning resolution setting is indicated by color of Status/Card light.
600dpi – The scanner is ready for use in 600dpi mode (default).
300dpi – After scanner is ready in 600dpi mode, press the power button again for
300dpi mode.

(green)
(color)
Initializing system and memory card. Please wait until the initialization process is complete before
using the scanner.
Busy scanning and storing picture files. Please wait until the process is complete before scanning
another original.
Battery compartment
takes 4 AAA (UM-4) batteries
(not included)
There is no battery charging
function in this scanner.
Recommend using NiMH rechargeable type batteries. We do not
recommend or support alkaline batteries. For acceptable battery
life, and to make sure your scanner operates dependably, use
recommended batteries.

8 Customer Support: http://www.pandigital.net/kodaksupport

(green)
(color)
Paper jam. Press the Power button. The scanner backs out the original so you can remove the
jammed original from the feed slot in photo scanning mode, and transparency output slot in filmstrip
scanning mode.
Calibration error. Please contact your nearest service center for help.

(color)
No memory card, card full (free space below 10MB), card error, card locked or the file system is not
supported. Remove files from the card to free up space, unlock the card if it is locked, or try another
card.

(green)

(color) The battery power is low.
The scanner is turned off.
Suitable and Unsuitable Original Types
Suitable
The scanner is designed to obtain the best scanning results with the following types of originals (without using a plastic
sheath):
3”x5”, 4”x6”, 5”x7”, 8x10” up to A4/Letter size
Business cards (standard 3.5”x2” (8.9x5 cm) or larger)
35mm negatives and slides (1-6 frames 35mm Negative adapter)
Unsuitable
Do not use the following types of originals for scanning. Otherwise the scanner may malfunction or cause the original to
jam in the slot.
Originals thicker than 1.0mm
Originals with either side shorter than 55mm
Originals with lots of black or dark colors
Originals with dark colors surrounding the edges
Printed pictures (pictures on newspapers, magazines, etc.)
Soft and thin materials (thin paper, cloth, etc.)
Over-exposed film/slides. To avoid auto-detection failure, remove any over-exposed frames from the beginning of the
filmstrip before feeding.
Over-sized film (i.e., 24x36mm) or professional High Exposure ISO 800+ film may cause the device to malfunction.
Originals that exceed the following acceptable size:
35mm Negative/Monochrome filmstrips are unsuitable with any of the following conditions:
1. Ends of the filmstrip are taped. Remove the tape and clean any residue of glue before scanning.
2. Ends of the filmstrip have not been cut straight across. Cut the ends straight across before
scanning.
Width 8.5 inches (216mm)
Length: 12 inches (304.8mm)

Customer Support: http://www.pandigital.net/kodaksupport 9
3. Ends of the filmstrip are folded. Cut the folded portions before scanning.
4. Ends of the filmstrip are tapered. Cut the ends straight across before scanning.
5. Some perforations on the filmstrip are torn or missing. This may affect the scanner’s auto feeding
mechanism. Gently push the filmstrip into the 35mm Negative adapter when necessary.
Supported Memory Cards
MS (MemoryStick)
MS Pro
MS Pro Duo (adapter required)
MS Duo
MMC (Multi Media Card)
RS-MMC (adapter required)
xD (extreme Digital, H-type and M-type)
SD (Secure Digital)
SDHC
MINISD (adapter required)
MICROSD/T-Flash (adapter required)
MICROSD Card (SD adapter required)
Plastic Sheaths
The plastic sheath is especially useful when scanning your older, fragile photos. The plastic sheath also helps eliminate the
possibility of de-focusing due to the uneven surface of curled photos.
1. Insert the photo into the plastic sheath as shown.
2. Adjust the paper guide lever so that the plastic sheath aligns against the left side of the
feed slot, and then insert the plastic sheath (with the folded side first) into the feed slot
flat and level as shown.
Use a soft, dry, lint-free cloth to wipe dust from the original and the plastic sheath.
Keep the original flat and level when feeding to prevent jamming.
Keep originals free from finger prints, oil, dirt, and dust for optimum scanned image quality.
Remove photos from the plastic sheath after scanning to prevent the plastic sheath from sticking to the photos over time.
Store plastic sheaths in a safe place and protect them from dust.
Fuzzy areas that result from the uneven
surface of the curled photo
Curled photo
A
djust the paper guide lever
Insert the
folded side
first

10 Customer Support: http://www.pandigital.net/kodaksupport
Orientation of the Original and Scanned Picture
It’s easy to see how scanned pictures appear on your computer. Note: You can rotate pictures on your computer.
Scanning the same original in different orientations may produce scanned pictures that look slightly different in color tones and
brightness. This is not a malfunction.
Operating the Scanner
Preparation and Initial Setup
The scanner can run on battery power or an external power supply.
When both power sources are available, the scanner only consumes power from the external power supply.
Recommended Ni-MH type rechargeable batteries. (There is no battery charging function in the scanner.)
1. Turn the scanner over and slide open the battery compartment cover.
2. Install four AAA (UM-4) batteries. Make sure the batteries are correctly installed according to the markings in
the battery compartment.
3. Replace the battery compartment cover.
4. Connect the plug on the power adapter to the power connector on the scanner.
5. Plug the power adapter into a power outlet.
The type of power plug and socket illustrated may differ from that of your region.
6. Insert the SD Memory Card (included) or any unlocked (writable) memory card into the memory card slot.
Always insert a memory card before scanning.
Make sure the memory card is unlocked (writable)
The scanner only accepts memory cards in FAT or FAT32 file system. NTFS and other file systems are not
supported.
Turning on the Scanner
1. Press the
Power button. The power indicator and Status/Card lights blink. (For more indicator lights
information, refer to “Indicator Lights” on page 7.)
2. Wait until the power indicator stops blinking and then turns off. The Status/Card indicator stays on steady,
indicating that the scanner is ready.
Do not insert an original into the feed slot when the power indicator is blinking; the original will not be
scanned.
Scanne
r
Original
Scanne
r
Original
Scanned image when
displayed on-screen

Customer Support: http://www.pandigital.net/kodaksupport 11
Setting the Scanning Resolution
The scanning resolution is measured in dpi (dots per inch). The higher the dpi, the more details on the original are captured by
the scanner and produce a higher quality scanned image. However, a higher dpi also results in a larger image size and occupy
more space on the memory card.
To change the scanning resolution, press and release the Power button. The scanning resolution changes by
each press of the button, and the color of the Status/Card indicator also change according to the resolution
selected:
Orange: 600dpi (fine mode, default setting)
Green: 300dpi (normal mode)
The scanning resolution for transparencies is fixed as 1200dpi and cannot be changed.
Scanning a Photo
1. Insert your photo into the plastic sheath (included with scanner).
2. With the photo facing upward and in correct orientation, place one edge of the photo on the
scanner and adjust the guide lever so that the photo aligns against the left side of the feed slot.
3. Insert the original level and flat into the feed slot.
CAUTION: Do not scan glossy photos in humid environments (humidity higher than 70% RH); the
surface of the photo becomes sticky and may cause the scanner to jam.
The original is fed through the slot and scanned automatically; the Power and Status/Card indicator
lights blink while scanning.
To prevent poor image quality, reserve adequate space behind the scanner for the photo to
complete the scan feeds.
When scanning is completed, the Power and Status/Card indicator lights blink while the scanner stores
the photo on the memory card.
Wait until the indicator lights stop blinking before inserting and scanning the next photo.
CAUTION: Insert only one photo at a time, and insert the next photo only when the previous one is done. Otherwise the
scanner may malfunction.
Do not remove the memory card or disconnect the power supply or batteries while the indicators are blinking.
This scanner produces JPEG (.jpg) file formats. The date/ time attribute are not added.
For more information on how this scanner stores the scanned picture files on the memory card, refer to “Orientation” on
page 10.
If the memory card is nearly full (less than 10MB remaining), the Status/Card indicator blinks (refer to “Indicator Lights” on
page 7). Use another card or transfer pictures to your computer.
To turn off the scanner, press and hold the power button for one second. The power indicator blinks and then
goes off.
Now you can safely disconnect the power and remove the memory card from the scanner.
The scanner automatically turns off if it’s left idle for 5 minutes. (If it’s connected to a computer, the scanner
does not automatically turn off.)
Scanning 35mm Negatives
This scanner only supports the scanning of 35mm negative/monochrome 6-frame 35mm filmstrips commonly available
from your local photo studios.
Filmstrips in certain conditions are not suitable for scanning. Refer to Suitable and Unsuitable Original Types on
page 8.
Guide Lever
A
lign left

12 Customer Support: http://www.pandigital.net/kodaksupport
Auto Image Mirror/Flip
The scanner can detect the orientation of a filmstrip when the printed numbers on the edge of the filmstrip are in the
same orientation as the picture.
If you feed the filmstrip with the image mirrored or upside-down, the scanner automatically adjusts the scanned
image during the scan.
The following orientations would result in the same scanned image:
For example, the bottom image (above) is upside-down but the numbers are right-side up. If fed in this
orientation, the picture would not be rotated, resulting in the scanned picture remaining upside-down.
The current recognition capability has difficulty distinguishing the direction of the number “3”, “6”, “8” and
“9”. The number’s position is near the edge of the film and can easily be worn out or damaged. When the
number on the edge cannot be detected in the expected position, or does not meet the required condition
above, the Auto Mirror/Flip function is disabled.
Feeding Filmstrips
1. Make sure that the feed slot is clear of any original, and that there is enough space behind the scanner for the filmstrip to
feed all the way through.
2. Slide the paper guide lever all the way to the right side of the feed slot.
3. Insert the 35mm film adapter all the way into the feed slot until it snaps into place, being careful not
to bend the metal parts.
Wait until indicator lights are in the “Ready to use” status before proceeding.
4. Hold up the negative towards light, with the image facing you in normal orientation (not mirror or
upside down).
5. Insert the filmstrip into the 35mm
Negative adapter.
No rotation required
A
uto mirrored
A
uto flipped
Final scanned image
If the numbers and image are not in the same orientation, or if numbers are damaged,
the auto mirror/flip function will not rotate the image.
Pay attention to the direction of
the filmstrip when inserting.

Customer Support: http://www.pandigital.net/kodaksupport 13
The filmstrip is fed into the slot and scanned. The Power and Status/Card indicator lights blink while
scanning.
Common filmstrip length is up to 6 negatives. To prevent poor image quality, reserve adequate
space behind the scanner for the filmstrip to complete the scan feeds.
While scanning a filmstrip, the scanner automatically recognizes the filmstrip type (negative) and
determines the best suitable scan and color enhancement settings for scanning.
The scanner scans filmstrips at a higher resolution; therefore the scanning speed is slower than
that of photo scanning. This is not a malfunction.
If the filmstrip is pulled out from the scanner while scanning, the scanning process remains for a
few seconds and then stops. This is not a malfunction.
When scanning is completed, the Power and Status/Card indicator lights blink while the scanner stores
the photo on the memory card.
Wait until the indicator lights stop blinking before inserting and scanning the next photo.
CAUTION: Insert only one filmstrip at a time, and insert the next filmstrip only when the previous one is done. Otherwise
the scanner may malfunction.
Do not remove the memory card or disconnect the power supply or batteries while the indicators are blinking.
This scanner produces JPEG (.jpg) file formats. The date/ time attribute are not added.
If the memory card is nearly full (less than 10MB remaining), the Status/Card indicator blinks (refer to “Indicator Lights” on
page 7). Use another card or transfer pictures to your computer.
To remove the 35mm Negative adapter after all filmstrips are scanned, gently pull it out from the
feed slot.
To power down the scanner, press and hold the power button for one second. The power indicator
blinks and then goes off.
Now you can safely disconnect the power and remove the memory card from the scanner.
The scanner automatically turns off if it’s left idle for 5 minutes. (If it’s connected to a computer, the
scanner does not automatically turn off.)
Automatic Image Cropping
The scanner has a built-in cropping function that detects and crops dark edges of an original during the scan process
(see following illustration).
Cropping size (as measured on the original)
Original size
Cropping size (as measured on the original
A B C D
When original size is
larger than 5”x7”
3 mm 3 mm 3 mm 3 mm
When original size is
smaller than 5”x7”
1.5 mm 1.5 mm 1.5 mm 1.5 mm
Original Scanned image
Scanning direction
B
D
C
A

14 Customer Support: http://www.pandigital.net/kodaksupport
Use the plastic sheath when scanning originals that are sized or shaped other than the standard 3.5”x5”, 4”x6”, or 5”x7”.
Depending on the shape, you may want to perform additional manual cropping on the scanned image, using your own
photo editing software, to achieve your desired final image.
When scanning darker originals (for example, a photo of the night sky),
over-cropping may occur.
When scanning over-exposed, older or lighter color (faded) filmstrip originals,
an irregular auto-cropping may occur. Cut the filmstrip into individual films and
rescan them.
Connect Scanner to a PC
By connecting the scanner to a computer, you can access the scanned pictures on the memory card directly, or use the scanner
as a memory card reader, so that you can freely copy, paste or delete files to and from the memory card using the PC.
PC System Requirements
Operating system: WINDOWS XP, WINDOWS VISTA, WINDOWS 7 or later - 32 bit
MAC OS 10.5, 10.6 or later
USB Port Supported: USB 1.1 or 2.0 port
1. Connect the plug on the power adapter cord to the power connector on the scanner.
2. Plug the power adapter into an electrical outlet.
The type of power plug and socket illustrated may differ from that of your region.
3. Insert the SD Memory Card (included) or any unlocked (writable) memory card into the memory card
slot.
Memory card is required. The scanned picture files are stored on an inserted memory card, and
then you can access the scanned pictures with WINDOWS EXPLORER or VISTA Photo Import
Wizard.
4. Connect the mini end of the USB cable (included with scanner) to the Mini USB connector on the
scanner.
5. Turn on your PC, and then connect the large end of the USB cable to a USB port on your PC.
6. Press the Power button; the power indicator light blinks. (For more information, refer to “Indicator Lights”
on page 7.)
CAUTION: Do not remove the memory card while the computer is accessing the files on it.
The scanner is recognized by the computer as a removable disk (WINDOWS system). Now you are ready to view or edit
the files on the memory card.

Customer Support: http://www.pandigital.net/kodaksupport 15
For WINDOWS VISTA Users
When the PC recognizes the scanner, with an inserted SD Card, an “Auto
Play” pop-up window appears.
To view photos on the PC while scanning, change WINDOWS EXPLORER
setting as follows:
1. Check the
Always do this for pictures checkbox.
2. Select
Open folder to view files option.
3. When the scanner connects with the PC, an additional drive is listed in the
EXPLORER window. If you are using the SD Memory Card, the drive is
titled KODAKSCN [drive letter].
If you are using your own memory card, the drive is titled Removable
Disk [drive letter] or the personalized title you may have previously
assigned to your memory card.
Do not select “Take no Action” or “Set AutoPlay to defaults in Control
Panel”.
For WINDOWS XP Users
When the PC recognizes the scanner with an inserted SD card, a pop-up
window appears.
To view photos on the PC while scanning, change WINDOWS EXPLORER
setting as follows:
1. Select
Open folder to view files using WINDOWS EXPLORER.
2. Select the “Always do the selected action” checkbox, and then click
OK.
3. When the scanner connects with the PC, an additional drive is listed in the
EXPLORER window. If you are using the SD Memory Card, the drive is
titled KODAKSCN [drive letter].
If you are using your own memory card, the drive is titled Removable
Disk [drive letter] or the personalized title you may have previously
assigned to your memory card.
For WINDOWS 7 Users
When the PC recognizes the scanner with an inserted SD card, WINDOWS
EXPLORER opens.
1. Select
KODAKSCN drive in EXPLORER window.
2. Open
PHOTO1 folder to view your scanned photos.
For MAC Users
When the computer recognizes the scanner with an inserted SD card, an
icon appears on the desktop; double-click it to open a Finder window.
1. Double-click the
KODAKSCN icon on the desktop.
2. Open
PHOTO1 folder to view your scanned photos.

16 Customer Support: http://www.pandigital.net/kodaksupport
Scanned Picture Naming Convention
After your first scan, a folder titled PHOTO1 is added to the memory card file structure.
The scanned pictures are saved in the PHOTO1 folder. Each scanned picture is given a file name with the prefix EK_
followed by a 4- digit sequential number in the order the pictures are stored. For example, EK_0001.jpg, EK_0002.jpg.
If the file name reaches EK_9999.jpg in the PHOTO1 folder, a new folder titled PHOTO2 is automatically created to
store subsequent new files, and so on.
There can be up to 9 folders (PHOTO1..9, EK_0001... EK_9999) on a memory card. If exceeded, the Status/Card
indicator light blinks.
You can now view or edit the files on the memory card using your own photo editing software.
Safely Disconnect the Scanner from Computer
For WINDOWS
1. On the WINDOWS System Tray, click the hardware removal icon as indicated below.
2. Click the ‘Safely remove USB mass Storage device’ message with the corresponding Drive.
3. When the ‘Safe to Remove Hardware’ message appears, you can safely remove the scanner’s USB cable.
For MAC
On the desktop, right-click on the KODAKSCN volume, then select Eject “KODAKSCN”.
Scan PC Software for KODAK Personal Photo Scanners
With the Scan PC Software for KODAK Personal Photo Scanners (Scan PC Software), you can easily scan photos and save the
scanned pictures directly to the connected PC.
System Requirements
Operating system: WINDOWS XP, WINDOWS VISTA, WINDOWS 7
Intel Pentium IV processor
1.2GHZ or better processor speed
512MB RAM
10MB free hard disk space
USB 2.0 compatible
Install Scan PC Software
1. Connect the scanner to your PC (see instructions beginning on page 14), using
the included SD Memory Card.
2. Open a Windows Explorer window.
3. Select
KODAKSCAN>KODAK>Software>KODAK_Scan_PC_Software_Setup_Vxxxx.
4. Double-click the
ScanPC_KODAK_Scanner_Setup_Vxxxx.exe file.
5. In the Install window, select Scan PC for KODAK Personal Photo Scanners, and
then click Install.
6. In the Install Wizard window, click Next.
7. Click
Next to install in default location, or select desired location and then click
Next.
8. In the Ready to Install window, click Install.
9. After the software is installed, click Finish.
Once installed, the
Scan PC Software runs automatically upon PC startup, and the icon stays on the system tray.
If you want to close the Scan PC Software temporarily, right-click on the icon and select Exit.
Hardware Removal Icon

Customer Support: http://www.pandigital.net/kodaksupport 17
Using the Scan PC Software
CAUTION: To maximize memory usage, close all other applications programs before scanning multi-image filmstrips.
After your first scan, a folder titled PHOTO1 is added to the file structure as follows:
~ Memory Card: \PHOTO1
~ Scan to PC: WINDOWS XP: C:\Documents and Settings\(your username)\My Documents\My Pictures\PHOTO1
WINDOWS VISTA or WINDOWS 7: C:\Users\(your username) \Pictures\PHOTO1
You can click the button to select a different location if desired.
4. Scan your original as instructed beginning on page 11.
5. The scanned picture is saved to the location you selected in step 2 above.
Each scanned picture is given a file name with the prefix EK_ followed by a 4- digit sequential number in the order the
pictures are stored. For example, EK_0001.jpg, EK_0002.jpg.
If the file name reaches EK_9999.jpg in the PHOTO1 folder, a new folder titled PHOTO2 is automatically created to
store subsequent new files, and so on.
Note: There can be up to 9 folders (PHOTO1..9, EK_0001... EK_9999) on a memory card. If exceeded, the
Status/Card indicator light blinks.
Launch Scan PC Software Manually
Uninstall the Scan PC Software
1. From the PC Start menu, select All Programs>Scan PC Software>Uninstall.
2. Follow the uninstall wizard to uninstall the software.
3. Restart your PC when prompted to do so.
If you choose to restart later, be aware that the Scan PC Software uninstall does not complete until you restart the PC.
Scan Mac Manager (Macintosh)
With the Scan Mac Manager, you can easily scan photos and save the scanned images directly to the connected computer. You
can also choose the location where the scanned images are saved.
System Requirements
Operating system: MACINTOSH OS X v10.6.x, MACINTOSH OS X v10.5.x, MACINTOSH OS X v10.4.x
Intel Duo Core/G3 processor
1.2GHZ or better/G3 processor speed
128MB RAM
10MB free hard disk space
USB 2.0 compatible
1. When the scanner is connected via USB cable to the PC, the Status/Card
light blinks. The Scan PC Software window appears.
2. Specify the location where you want the scanned pictures to be saved:
~ Memory Card
~ Scan to PC
3. Click
Apply; the window closes.
Double-click the icon on the Desktop, or right-click the icon in the system tray and select Setting.
If you want to close the Scan PC Software temporarily, right-click on the icon and select Exit.
Installing the Scan Mac Manager
1. Connect the Scanner to your computer (see instructions beginning on page 14), using the included SD card.
2. Open a Finder window.
3. Select
KODAKSCAN>KODAK>Software>KODAK_Scan_Mac_Software_Setup_Vxxxx.
4. Double-click the
ScanMac_KODAK_Scanner_Setup_Vxxxx.zip file.
5. Double-click Scan2Mac to begin the installation.
6. Follow the on-screen instructions to complete the installation.
7. Click Restart to restart your computer.
8. The Scan Mac Manager automatically starts when the restart is complete.
Once installed, the
Scan Mac Manager opens whenever you connect the Scanner.

18 Customer Support: http://www.pandigital.net/kodaksupport
Using the Scan Mac Manager
File Naming Convention
Each scanned image is given a file name with the prefix EK_ followed by a 4- digit sequential number in the order the
images are stored. For example, EK_0001.JPG, EK_0002.JPG.
If the file name reaches EK_9999.JPG in the PHOTO1 folder, a new folder titled PHOTO2 is automatically created to store
subsequent new files, and so on.
There can be up to 9 folders (PHOTO1..9, EK_0001... EK_9999) on a memory card. If exceeded, the Status/Card
indicator light blinks. Delete some files on the memory card or use another one if necessary.
Manually Start the Scan Mac Manager
1. Open a Finder window.
2. Click Applications, and then double-click .
Uninstalling the Scan Mac Manager
1. Close the Scan Mac Manager by clicking the icon in the top Finder bar, and then click Exit.
2. Click Yes to confirm you want to exit the application.
3. Open a Finder window.
4. Click Applications, right-click Scan Mac, and then select Move to Trash.
KODAK EASYSHARE Software for PC
After using Scan PC Software for KODAK Personal Photo Scanners to scan and store your pictures on your PC, you can use
EASYSHARE Software to organize, edit, print, and share your pictures online.
System Requirements
Operating system: WINDOWS XP, WINDOWS VISTA, WINDOWS 7
Intel Pentium IV processor
1.2GHZ or better processor speed
512MB RAM
200MB free hard disk space
Install EASYSHARE Software
1. When the Scanner is connected via USB cable to the computer,
the Status/Card light blinks. The Scan Mac Manager window
appears.
2. You can specify the location where you want the scanned images to be
saved, either on the memory card or in a specific folder on the computer.
After your first scan, a folder titled PHOTO1 is added to the file structure.
Therefore, if Scan Mac is selected, the scanned images are saved to the
following location by default:
/Users/(your username)/Pictures/PHOTO1/
You can also click the button to select a different location if you
prefer.
3. Click
Apply; the window closes.
4. Scan your original as instructed beginning on page 11.
5. The scanned image are saved to the location you selected in step 2 above.
1. Insert the SD Memory Card into the scanner.
2. Connect the scanner to your PC (see instructions beginning on page 14)
using the included SD card.
Scan Mac

Customer Support: http://www.pandigital.net/kodaksupport 19
Launch EASYSHARE
Uninstall the EASYSHARE Software
1. Open WINDOWS Control Panel.
2. WINDOWS VISTA: Select
Programs>Uninstall a Program
WINDOWS 7: Select Programs and Features
WINDOWS XP: Select Add or Remove a Program
3. Select
Kodak EASYSHARE Software, and then click Uninstall.
4. Follow the prompts to complete.
3. Open a Windows Explorer window.
4. Select
KODAKSCAN>KODAK>
Software>KODAK_Scan_PC_Software_Setup_Vxxxx>KodakEasyShare.
5. Double-click the
Setup.exe file.
6. Follow the prompts to install and register your software.
7. After the software is installed, click Finish.
1. Double-click the KODAK EASYSHARE shortcut on your desktop
or select Kodak EASYSHARE software from the Start>Programs list.
2. Click
Add Pictures.
3. Select the
PHOTO1 folder containing the scanned pictures (as
designated during the Scan PC usage, pg. 17).
4. Select the desired pictures to add to an Album.
5. Enter a new Album destination name.
6. Click
Add Pictures, and then Done.
7. Using the top row of options in the EASYSHARE window, pictures that
you’ve copied into Albums can be edited and enhanced, copied to
other locations, and uploaded directly into your FACEBOOK or
FLICKR accounts for quick and easy sharing.
8. Use the
Help for complete usage instructions on all features.
 





20 Customer Support: http://www.pandigital.net/kodaksupport
KODAK EASYSHARE Software for MACINTOSH
After using Scan PC Software for KODAK Personal Photo Scanners to scan and store your pictures on your computer, you can
use EASYSHARE Software to organize, edit, print, and share your pictures online.
System Requirements
Operating system: MACINTOSH OS X v10.6.x, MACINTOSH OS X v10.5.x, MACINTOSH OS X v10.4.x
Intel Duo Core/G3 processor
1.2GHZ or better/G3 processor speed
128MB RAM
200MB free hard disk space
Install EASYSHARE Software
1. Verify that your computer meets the system requirements.
2. Close all programs.
3. Disconnect all accessory devices from your computer. For example, digital camera, camera dock, printer dock, photo
printer, card reader, etc.
4. Insert the SD Memory Card into the scanner, and then connect the scanner to your computer.
5. Select
KODAKSCAN>KODAK>Software>KODAK_Scan_Mac_Software_Setup_VQ1.01\KODAK EasyShare
Mac>KodakEasyShare_v6_2.dmg to install and the follow the on-screen instructions.
6. Use the
Help feature in the software or go to www.kodak.com for complete usage instructions.
Uninstall the EASYSHARE Software
1. Open a Finder window.
2. Click Applications, right-click EasyShare, and then select Move to Trash.
Scanner Maintenance
Cleaning the Scanner
In order to maintain the scanned image quality and prevent dust accumulation, it is recommended that you clean the
scanner (outer casing, image sensor and roller inside the scanner) approximately every 50-100 scans.
Clean the scanner also if:
vertical lines or stripes appear on the scanned picture
photos or film will not feed
Use only the recommended and supplied tools to clean the scanner.
WARNING: Do not use any solvents or corrosive liquid (i.e., alcohol, kerosene, etc.) to clean any part of the scanner.
Otherwise the plastic material may be permanently damaged.
Clean the Outer Casing
1. Use a suitable dust blower to blow off the dust on the scanner.
2. Use a slightly dampened cloth to wipe off any smears on the surface of the scanner.
3. Wipe the scanner with a dry and clean lint-free cloth.
Clean the Image Sensor
1. Clean the scanner’s outer casing first.
2. With the scanner powered off and disconnected from the power supply, insert the
sensor cleaning swab into one end of the output slot.
Make sure that there is no visible dust on the swab before inserting it into the output
slot
3. Gently slide the sensor cleaning swab back and forth from one end of the output slot to
the other five or six times consecutively.
CAUTION: Do not apply too much force on the swab.