Kogan AC1200 User manual

WI-FI AC1200 WHOLE-
HOME MESH
(3 PACK, WI-FI 5)
KAWM6WF53PA

• Mesh3 Node (x3)
• Power Adapter (x3)
• Ethernet Cable
• User Guide
Wall mounting hole
Used to fix the device to the wall. Recommended specifications are:
• Screws: PA3x14 mm; head diameter: 5.2 mm; head thickness: 1.8 mm
• Plastic anchor: inner diameter: 2.4 mm; length: 26.4 mm
COMPONENTS LIST
OVERVIEW
DC power jack
WAN/LAN port
LAN port
Reset
button
Wall mounting holes

Install the KoganMesh App
Download the KoganMesh App onto your mobile device by searching for
KoganMesh in App Store or Google Play or by scanning the QR code.
Then install the KoganMesh App.
INSTALLATION
Available for iOS and Android
KoganMesh App

Connect the Primary node:
The first node you set up functions as the primary node, while the rest are referred to as the
secondary nodes.
1. Power off your modem and remove its battery (if any).
2. Use the included Ethernet cable to connect a LAN port of your modem or the
Ethernet jack to the (WAN/LAN) port of one of the nodes. This node is your primary
node.
3. Reinstall its battery and power on your modem.
4. Use the included power adapter to connect the primary node to a power source,
the LED indicator lights solid green. Wait about for 40 seconds. The system
completes start-up when the LED indicator blinks green.
Internet
Ethernet jack
Modem
Reset

Connect the primary node to the internet
1. Go to the Wi-Fi network list on your mobile device, select the SSID of the primary
node and enter its password. The SSID and password are specified on the bottom
label of any node.
2. Run the KoganMesh App and follow the onscreen instructions to connect the
primary node to the internet. After the primary node is connected to the internet,
its LED indicator lights solid green.
LED

Connect the secondary nodes to the internet
1. Place each node:
• In a high & open area
• Ensure that there are less than two walls between any two nodes.
• Keep your nodes away from electronics with strong interference, such as microwave
ovens, induction cookers and refrigerators.
2. Use other power adapters to connect the remaining secondary nodes to power outlets,
the LED indicators will turn solid green. Wait for about 40 seconds. The secondary node
is connecting to another node when its LED indicator blinks green.
3. Observe the LED indicator of the secondary nodes until their LED indicators are one of
the following colours:
Solid Green
Good Connection
Solid Yellow
Fair Connection
Solid Red
Disconnected
4. If a node's LED indicator does not light solid green, you can relocate it ensuring you
avoid obstructions and any electronic interference.

To access the internet:
• Wired devices: Connect wired devices to the LAN ports of your nodes.
• Wireless devices: Connect wireless devices to the Wi-Fi network using the SSID and Wi-
Fi password you set.
• To manage the network anytime anywhere, tap “ ” icon in the app and use your
account to login.

Input
100 - 240 V, AC, 50/60 Hz, 0.4 A
Output
12 V, DC 1 A
Operating Temperature
0-40°C
Operating Humidity
(10-90) % RH, non-condensing
Q1: How can I remove a node from my Wi-Fi network?
A1: Tap the node on the KoganMesh App, tap ... in the upper-right corner and choose
Delete.
Q2: Can I add another new set of nodes to expand my network coverage?
A2: Yes. Run the KoganMesh App, tap Settings in the lower-right corner, tap Add nova and
follow the on-screen instructions.
Q3: How to restore my network to factory settings?
A3: With your nodes powered on, hold the Reset button of your primary node down using a
sharp item (such as a pin) for about 6 seconds and release it when the LED indicator blinks
fast. Your network is reset successfully when the LED indicator lights solid green then blinks
slow again. All nodes will be restored to factory settings.
FAQ
Note:
Removing operation restores the node to factory settings.
SPECIFCATIONS

Q4. My 2.4 GHz Wi-Fi-enabled devices, such as a home security camera, cannot connect
to my nova Wi-Fi network. What should I do?
A4: Please try the following solution:
Step 1: Connect your smart phone used during setup to your Wi-Fi network.
Step 2: Run the KoganMesh App, tap Settings, Smart Assistant and Enable.
Your smart phone will connect to the 2.4 GHz Wi-Fi network.
Step 3: Use the smart phone to set up your 2.4 GHz Wi-Fi-enabled device following the
prompts in the app.
Disposal
This marking indicates that this appliance should not be disposed with
other household wastes. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources.