Kogan KADSAFSA9LA User manual

DIGITAL SECURITY SAFE
LOCK BOX
KADSAFSA9LA, KADSAFL27LA & KADSAFM16LA

• Do not install the safe in an elevated, insecure location. A falling safe can cause
serious personal injury and damage to the product.
• Do not use any liquids or a spray cleaner to clean the safe. Wipe with a damp cloth
instead.
• Do not expose the control panel to water or any other liquids as this may cause
electric shock and damage the internal components.
• This product does not contain any user serviceable parts. Do not dismantle or
modify the product in any way. Unguided dismantling and incorrect reassembly
may damage the electrical components. If repairs are required, please contact
help.Kogan.com for support.
• Never store the emergency keys inside the safe.
SAFETY & WARNINGS

Safe
Control panel
1
Bolts
2
Reset Button
3
Battery Compartment
4
Knob
5
Emergency Lock Cover
6
Indicator
7
Confirm Button (#)
OVERVIEW

• Select a stable, dry and secure location for the safe.
• If bolting to a wall, ensure that your safe is resting on a well-supported surface
(such as the floor or a shelf). Do not bolt your safe to both the floor and wall.
• Place the safe in the selected location. Use a pencil to mark the mounting holes on
the floor or wall.
• Move the safe and drill the holes 50mm deep using the appropriately sized drill bit.
Note: If you have any doubt regarding the installation or appropriate hardware for
your application, contact a qualified trades person for advice before drilling.
• Move the safe back into position and align the mounting holes to the openings in
the safe.
• If you are mounting into concrete, insert the included expansion anchors into the
holes before securing the safe in place using the suppled bolts.
• Tighten the bolts securely.
INSTALLATION
WARNING: Always use the expansion anchor when mounting to a
concrete surface.
Expansion anchor
Bolt
C
A
B

Installing the Batteries
• Remove the emergency lock cover and unlock the safe using the emergency key.
• Pull the door open.
• Remove the battery compartment cover.
• Insert x4 AA batteries into the battery compartment. Pay close attention to the
orientation of the polarity symbols (+ and -).
Setting the Passcode
By default the factory passcode is “159”. It i s h i g h ly recommended to change the passcode
to something more secure.
• Open the door and press the reset button, the yellow indicator will flash and the
safe will beep.
• Input a new code (between 3-8 digits) and press “#” to confirm. If the code change
has been successful, the yellow indicator will flash twice and the safe will emit 2
beeps.
• If the yellow light flashes 3 times with 3 beeps, the code change has failed and the
process will need to be repeated.
Unlocking the Safe
Passcode:
1. Input the passcode and press the “#” button to confirm.
2. The yellow indicator will flash twice, the safe will emit 2 beeps and the green
indicator will turn on.
3. The safe has been successfully unlocked. Turn the knob clockwise to open the safe.
OPERATION
Note:
If the red indicator turns on during operation, the batteries are low and will need to be
replaced. It is highly recommended to use a high-powered alkaline battery.

Emergency key:
In the event the passcode cannot be used, you can use the emergency key to unlock and
open the safe.
1. Remove the emergency lock cover.
2. Insert the emergency key and turn counter-clockwise.
3. Tu r n t h e k n o b c l o c k w i s e a n d open the door.
Resetting the Safe
To return the safe back to factory settings, open the safe then press and hold the reset
button until the yellow indicator flashes twice and the safe emits 2 beeps. The passcode will
return to the default code “159”.
WARNING: Ensure the emergency keys are kept in a safe place. Never
store them in safe.

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com.